xref: /freebsd/sys/contrib/device-tree/Bindings/mmc/arm,pl18x.yaml (revision e6bfd18d21b225af6a0ed67ceeaf1293b7b9eba5) 
1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: ARM PrimeCell MultiMedia Card Interface (MMCI) PL180 and PL181
8
9maintainers:
10  - Linus Walleij <linus.walleij@linaro.org>
11  - Ulf Hansson <ulf.hansson@linaro.org>
12
13description:
14  The ARM PrimeCells MMCI PL180 and PL181 provides an interface for
15  reading and writing to MultiMedia and SD cards alike. Over the years
16  vendors have use the VHDL code from ARM to create derivative MMC/SD/SDIO
17  host controllers with very similar characteristics.
18
19allOf:
20  - $ref: /schemas/arm/primecell.yaml#
21  - $ref: mmc-controller.yaml#
22
23# We need a select here so we don't match all nodes with 'arm,primecell'
24select:
25  properties:
26    compatible:
27      contains:
28        enum:
29          - arm,pl180
30          - arm,pl181
31          - arm,pl18x
32  required:
33    - compatible
34
35properties:
36  compatible:
37    oneOf:
38      - description: The first version of the block, simply called
39          PL180 and found in the ARM Integrator IM/PD1 logic module.
40        items:
41          - const: arm,pl180
42          - const: arm,primecell
43      - description: The improved version of the block, found in the
44          ARM Versatile and later reference designs. Further revisions
45          exist but get detected at runtime by reading some magic numbers
46          in the PrimeCell ID registers.
47        items:
48          - const: arm,pl181
49          - const: arm,primecell
50      - description: Wildcard entry that will let the operating system
51          inspect the PrimeCell ID registers to determine which hardware
52          variant of PL180 or PL181 this is.
53        items:
54          - const: arm,pl18x
55          - const: arm,primecell
56      - description: Entry for STMicroelectronics variant of PL18x.
57          This dedicated compatible is used by bootloaders.
58        items:
59          - const: st,stm32-sdmmc2
60          - const: arm,pl18x
61          - const: arm,primecell
62
63  clocks:
64    description: One or two clocks, the "apb_pclk" and the "MCLK"
65      which is the core block clock. The names are not compulsory.
66    minItems: 1
67    maxItems: 2
68
69  dmas:
70    maxItems: 2
71
72  dma-names:
73    oneOf:
74      - items:
75          - const: tx
76          - const: rx
77      - items:
78          - const: rx
79          - const: tx
80
81  power-domains: true
82
83  resets:
84    maxItems: 1
85
86  reg:
87    description: the MMIO memory window must be exactly 4KB (0x1000) and the
88      layout should provide the PrimeCell ID registers so that the device can
89      be discovered. On ST Micro variants, a second register window may be
90      defined if a delay block is present and used for tuning.
91
92  interrupts:
93    description: The first interrupt is the command interrupt and corresponds
94      to the event at the end of a command. The second interrupt is the
95      PIO (polled I/O) interrupt and occurs when the FIFO needs to be
96      emptied as part of a bulk read from the card. Some variants have these
97      two interrupts wired into the same line (logic OR) and in that case
98      only one interrupt may be provided.
99    minItems: 1
100    maxItems: 2
101
102  st,sig-dir-dat0:
103    $ref: /schemas/types.yaml#/definitions/flag
104    description: ST Micro-specific property, bus signal direction pins used for
105      DAT[0].
106
107  st,sig-dir-dat2:
108    $ref: /schemas/types.yaml#/definitions/flag
109    description: ST Micro-specific property, bus signal direction pins used for
110      DAT[2].
111
112  st,sig-dir-dat31:
113    $ref: /schemas/types.yaml#/definitions/flag
114    description: ST Micro-specific property, bus signal direction pins used for
115      DAT[3] and DAT[1].
116
117  st,sig-dir-dat74:
118    $ref: /schemas/types.yaml#/definitions/flag
119    description: ST Micro-specific property, bus signal direction pins used for
120      DAT[7] and DAT[4].
121
122  st,sig-dir-cmd:
123    $ref: /schemas/types.yaml#/definitions/flag
124    description: ST Micro-specific property, CMD signal direction used for
125      pin CMD.
126
127  st,sig-pin-fbclk:
128    $ref: /schemas/types.yaml#/definitions/flag
129    description: ST Micro-specific property, feedback clock FBCLK signal pin
130      in use.
131
132  st,sig-dir:
133    $ref: /schemas/types.yaml#/definitions/flag
134    description: ST Micro-specific property, signal direction polarity used for
135      pins CMD, DAT[0], DAT[1], DAT[2] and DAT[3].
136
137  st,neg-edge:
138    $ref: /schemas/types.yaml#/definitions/flag
139    description: ST Micro-specific property, data and command phase relation,
140      generated on the sd clock falling edge.
141
142  st,use-ckin:
143    $ref: /schemas/types.yaml#/definitions/flag
144    description: ST Micro-specific property, use CKIN pin from an external
145      driver to sample the receive data (for example with a voltage switch
146      transceiver).
147
148  st,cmd-gpios:
149    maxItems: 1
150    description:
151      The GPIO matching the CMD pin.
152
153  st,ck-gpios:
154    maxItems: 1
155    description:
156      The GPIO matching the CK pin.
157
158  st,ckin-gpios:
159    maxItems: 1
160    description:
161      The GPIO matching the CKIN pin.
162
163dependencies:
164  st,cmd-gpios: [ "st,use-ckin" ]
165  st,ck-gpios: [ "st,use-ckin" ]
166  st,ckin-gpios: [ "st,use-ckin" ]
167
168unevaluatedProperties: false
169
170required:
171  - compatible
172  - reg
173  - interrupts
174
175examples:
176  - |
177    #include <dt-bindings/interrupt-controller/irq.h>
178    #include <dt-bindings/gpio/gpio.h>
179
180    mmc@5000 {
181      compatible = "arm,pl180", "arm,primecell";
182      reg = <0x5000 0x1000>;
183      interrupts-extended = <&vic 22 &sic 1>;
184      clocks = <&xtal24mhz>, <&pclk>;
185      clock-names = "mclk", "apb_pclk";
186    };
187
188  - |
189    #include <dt-bindings/interrupt-controller/irq.h>
190
191    mmc@80126000 {
192      compatible = "arm,pl18x", "arm,primecell";
193      reg = <0x80126000 0x1000>;
194      interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
195      dmas = <&dma 29 0 0x2>, <&dma 29 0 0x0>;
196      dma-names = "rx", "tx";
197      clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
198      clock-names = "sdi", "apb_pclk";
199      max-frequency = <100000000>;
200      bus-width = <4>;
201      cap-sd-highspeed;
202      cap-mmc-highspeed;
203      cd-gpios  = <&gpio2 31 0x4>;
204      st,sig-dir-dat0;
205      st,sig-dir-dat2;
206      st,sig-dir-cmd;
207      st,sig-pin-fbclk;
208      vmmc-supply = <&ab8500_ldo_aux3_reg>;
209      vqmmc-supply = <&vmmci>;
210    };
211
212  - |
213    mmc@101f6000 {
214      compatible = "arm,pl18x", "arm,primecell";
215      reg = <0x101f6000 0x1000>;
216      clocks = <&sdiclk>, <&pclksdi>;
217      clock-names = "mclk", "apb_pclk";
218      interrupts = <22>;
219      max-frequency = <400000>;
220      bus-width = <4>;
221      cap-mmc-highspeed;
222      cap-sd-highspeed;
223      full-pwr-cycle;
224      st,sig-dir-dat0;
225      st,sig-dir-dat2;
226      st,sig-dir-dat31;
227      st,sig-dir-cmd;
228      st,sig-pin-fbclk;
229      vmmc-supply = <&vmmc_regulator>;
230    };
231
232  - |
233    mmc@52007000 {
234      compatible = "arm,pl18x", "arm,primecell";
235      arm,primecell-periphid = <0x10153180>;
236      reg = <0x52007000 0x1000>;
237      interrupts = <49>;
238      clocks = <&rcc 0>;
239      clock-names = "apb_pclk";
240      resets = <&rcc 1>;
241      cap-sd-highspeed;
242      cap-mmc-highspeed;
243      max-frequency = <120000000>;
244    };
245