1* Analog Devices ADV7604/11/12 video decoder with HDMI receiver 2 3The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated 4HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog 5input, and the ADV7611 has one HDMI input and no analog input. The 7612 is 6similar to the 7611 but has 2 HDMI inputs. 7 8These device tree bindings support the ADV7611/12 only at the moment. 9 10Required Properties: 11 12 - compatible: Must contain one of the following 13 - "adi,adv7611" for the ADV7611 14 - "adi,adv7612" for the ADV7612 15 16 - reg: I2C slave addresses 17 The ADV76xx has up to thirteen 256-byte maps that can be accessed via the 18 main I2C ports. Each map has it own I2C address and acts as a standard 19 slave device on the I2C bus. The main address is mandatory, others are 20 optional and revert to defaults if not specified. 21 22 - hpd-gpios: References to the GPIOs that control the HDMI hot-plug 23 detection pins, one per HDMI input. The active flag indicates the GPIO 24 level that enables hot-plug detection. 25 26The device node must contain one 'port' child node per device input and output 27port, in accordance with the video interface bindings defined in 28Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes 29are numbered as follows. 30 31 Port ADV7611 ADV7612 32------------------------------------------------------------ 33 HDMI 0 0, 1 34 Digital output 1 2 35 36The digital output port node must contain at least one endpoint. 37 38Optional Properties: 39 40 - reset-gpios: Reference to the GPIO connected to the device's reset pin. 41 - default-input: Select which input is selected after reset. 42 - reg-names : Names of maps with programmable addresses. 43 It can contain any map needing a non-default address. 44 Possible maps names are : 45 "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe", 46 "rep", "edid", "hdmi", "test", "cp", "vdp" 47 48Optional Endpoint Properties: 49 50 The following three properties are defined in video-interfaces.txt and are 51 valid for source endpoints only. 52 53 - hsync-active: Horizontal synchronization polarity. Defaults to active low. 54 - vsync-active: Vertical synchronization polarity. Defaults to active low. 55 - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge. 56 57 If none of hsync-active, vsync-active and pclk-sample is specified the 58 endpoint will use embedded BT.656 synchronization. 59 60Example: 61 62 hdmi_receiver@4c { 63 compatible = "adi,adv7611"; 64 /* 65 * The edid page will be accessible @ 0x66 on the I2C bus. All 66 * other maps will retain their default addresses. 67 */ 68 reg = <0x4c>, <0x66>; 69 reg-names = "main", "edid"; 70 71 reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>; 72 hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>; 73 74 #address-cells = <1>; 75 #size-cells = <0>; 76 77 default-input = <0>; 78 79 port@0 { 80 reg = <0>; 81 }; 82 port@1 { 83 reg = <1>; 84 hdmi_in: endpoint { 85 remote-endpoint = <&ccdc_in>; 86 }; 87 }; 88 }; 89