xref: /freebsd/sys/contrib/device-tree/Bindings/i2c/snps,designware-i2c.yaml (revision 06c3fb2749bda94cb5201f81ffdb8fa6c3161b2e) 
1# SPDX-License-Identifier: GPL-2.0-only
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/i2c/snps,designware-i2c.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Synopsys DesignWare APB I2C Controller
8
9maintainers:
10  - Jarkko Nikula <jarkko.nikula@linux.intel.com>
11
12allOf:
13  - $ref: /schemas/i2c/i2c-controller.yaml#
14  - if:
15      properties:
16        compatible:
17          not:
18            contains:
19              const: mscc,ocelot-i2c
20    then:
21      properties:
22        reg:
23          maxItems: 1
24
25properties:
26  compatible:
27    oneOf:
28      - description: Generic Synopsys DesignWare I2C controller
29        const: snps,designware-i2c
30      - description: Microsemi Ocelot SoCs I2C controller
31        items:
32          - const: mscc,ocelot-i2c
33          - const: snps,designware-i2c
34      - description: Baikal-T1 SoC System I2C controller
35        const: baikal,bt1-sys-i2c
36
37  reg:
38    minItems: 1
39    items:
40      - description: DW APB I2C controller memory mapped registers
41      - description: |
42          ICPU_CFG:TWI_DELAY registers to setup the SDA hold time.
43          This registers are specific to the Ocelot I2C-controller.
44
45  interrupts:
46    maxItems: 1
47
48  clocks:
49    minItems: 1
50    items:
51      - description: I2C controller reference clock source
52      - description: APB interface clock source
53
54  clock-names:
55    minItems: 1
56    items:
57      - const: ref
58      - const: pclk
59
60  resets:
61    maxItems: 1
62
63  clock-frequency:
64    description: Desired I2C bus clock frequency in Hz
65    enum: [100000, 400000, 1000000, 3400000]
66    default: 400000
67
68  i2c-sda-hold-time-ns:
69    description: |
70      The property should contain the SDA hold time in nanoseconds. This option
71      is only supported in hardware blocks version 1.11a or newer or on
72      Microsemi SoCs.
73
74  i2c-scl-falling-time-ns:
75    description: |
76      The property should contain the SCL falling time in nanoseconds.
77      This value is used to compute the tLOW period.
78    default: 300
79
80  i2c-sda-falling-time-ns:
81    description: |
82      The property should contain the SDA falling time in nanoseconds.
83      This value is used to compute the tHIGH period.
84    default: 300
85
86  dmas:
87    items:
88      - description: TX DMA Channel
89      - description: RX DMA Channel
90
91  dma-names:
92    items:
93      - const: tx
94      - const: rx
95
96unevaluatedProperties: false
97
98required:
99  - compatible
100  - reg
101  - interrupts
102
103examples:
104  - |
105    i2c@f0000 {
106      compatible = "snps,designware-i2c";
107      reg = <0xf0000 0x1000>;
108      interrupts = <11>;
109      clock-frequency = <400000>;
110    };
111  - |
112    i2c@1120000 {
113      compatible = "snps,designware-i2c";
114      reg = <0x1120000 0x1000>;
115      interrupts = <12 1>;
116      clock-frequency = <400000>;
117      i2c-sda-hold-time-ns = <300>;
118      i2c-sda-falling-time-ns = <300>;
119      i2c-scl-falling-time-ns = <300>;
120    };
121  - |
122    i2c@2000 {
123      compatible = "snps,designware-i2c";
124      reg = <0x2000 0x100>;
125      #address-cells = <1>;
126      #size-cells = <0>;
127      clock-frequency = <400000>;
128      clocks = <&i2cclk>;
129      interrupts = <0>;
130
131      eeprom@64 {
132        compatible = "atmel,24c02";
133        reg = <0x64>;
134      };
135    };
136  - |
137    i2c@100400 {
138      compatible = "mscc,ocelot-i2c", "snps,designware-i2c";
139      reg = <0x100400 0x100>, <0x198 0x8>;
140      pinctrl-0 = <&i2c_pins>;
141      pinctrl-names = "default";
142      interrupts = <8>;
143      clocks = <&ahb_clk>;
144    };
145...
146