1CE4100 I2C 2---------- 3 4CE4100 has one PCI device which is described as the I2C-Controller. This 5PCI device has three PCI-bars, each bar contains a complete I2C 6controller. So we have a total of three independent I2C-Controllers 7which share only an interrupt line. 8The driver is probed via the PCI-ID and is gathering the information of 9attached devices from the devices tree. 10Grant Likely recommended to use the ranges property to map the PCI-Bar 11number to its physical address and to use this to find the child nodes 12of the specific I2C controller. This were his exact words: 13 14 Here's where the magic happens. Each entry in 15 ranges describes how the parent pci address space 16 (middle group of 3) is translated to the local 17 address space (first group of 2) and the size of 18 each range (last cell). In this particular case, 19 the first cell of the local address is chosen to be 20 1:1 mapped to the BARs, and the second is the 21 offset from be base of the BAR (which would be 22 non-zero if you had 2 or more devices mapped off 23 the same BAR) 24 25 ranges allows the address mapping to be described 26 in a way that the OS can interpret without 27 requiring custom device driver code. 28 29This is an example which is used on FalconFalls: 30------------------------------------------------ 31 i2c-controller@b,2 { 32 #address-cells = <2>; 33 #size-cells = <1>; 34 compatible = "pci8086,2e68.2", 35 "pci8086,2e68", 36 "pciclass,ff0000", 37 "pciclass,ff00"; 38 39 reg = <0x15a00 0x0 0x0 0x0 0x0>; 40 interrupts = <16 1>; 41 42 /* as described by Grant, the first number in the group of 43 * three is the bar number followed by the 64bit bar address 44 * followed by size of the mapping. The bar address 45 * requires also a valid translation in parents ranges 46 * property. 47 */ 48 ranges = <0 0 0x02000000 0 0xdffe0500 0x100 49 1 0 0x02000000 0 0xdffe0600 0x100 50 2 0 0x02000000 0 0xdffe0700 0x100>; 51 52 i2c@0 { 53 #address-cells = <1>; 54 #size-cells = <0>; 55 compatible = "intel,ce4100-i2c-controller"; 56 57 /* The first number in the reg property is the 58 * number of the bar 59 */ 60 reg = <0 0 0x100>; 61 62 /* This I2C controller has no devices */ 63 }; 64 65 i2c@1 { 66 #address-cells = <1>; 67 #size-cells = <0>; 68 compatible = "intel,ce4100-i2c-controller"; 69 reg = <1 0 0x100>; 70 71 /* This I2C controller has one gpio controller */ 72 gpio@26 { 73 #gpio-cells = <2>; 74 compatible = "ti,pcf8575"; 75 reg = <0x26>; 76 gpio-controller; 77 }; 78 }; 79 80 i2c@2 { 81 #address-cells = <1>; 82 #size-cells = <0>; 83 compatible = "intel,ce4100-i2c-controller"; 84 reg = <2 0 0x100>; 85 86 gpio@26 { 87 #gpio-cells = <2>; 88 compatible = "ti,pcf8575"; 89 reg = <0x26>; 90 gpio-controller; 91 }; 92 }; 93 }; 94