xref: /freebsd/sys/contrib/device-tree/Bindings/gpio/gpio-mmio.yaml (revision 5b56413d04e608379c9a306373554a8e4d321bc0) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/gpio/gpio-mmio.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Generic MMIO GPIO
8
9maintainers:
10  - Linus Walleij <linus.walleij@linaro.org>
11  - Bartosz Golaszewski <brgl@bgdev.pl>
12
13description:
14  Some simple GPIO controllers may consist of a single data register or a pair
15  of set/clear-bit registers. Such controllers are common for glue logic in
16  FPGAs or ASICs. Commonly, these controllers are accessed over memory-mapped
17  NAND-style parallel busses.
18
19properties:
20  compatible:
21    enum:
22      - brcm,bcm6345-gpio
23      - ni,169445-nand-gpio
24      - wd,mbl-gpio # Western Digital MyBook Live memory-mapped GPIO controller
25
26  big-endian: true
27
28  '#gpio-cells':
29    const: 2
30
31  gpio-controller: true
32
33  little-endian: true
34
35  reg:
36    minItems: 1
37    description:
38      A list of registers in the controller. The width of each register is
39      determined by its size. All registers must have the same width. The number
40      of GPIOs is set by the width, with bit 0 corresponding to GPIO 0.
41    items:
42      - description:
43          Register to READ the value of the GPIO lines. If GPIO line is high,
44          the bit will be set. If the GPIO line is low, the bit will be cleared.
45          This register may also be used to drive GPIOs if the SET register is
46          omitted.
47      - description:
48          Register to SET the value of the GPIO lines. Setting a bit in this
49          register will drive the GPIO line high.
50      - description:
51          Register to CLEAR the value of the GPIO lines. Setting a bit in this
52          register will drive the GPIO line low. If this register is omitted,
53          the SET register will be used to clear the GPIO lines as well, by
54          actively writing the line with 0.
55      - description:
56          Register to set the line as OUTPUT. Setting a bit in this register
57          will turn that line into an output line. Conversely, clearing a bit
58          will turn that line into an input.
59      - description:
60          Register to set this line as INPUT. Setting a bit in this register
61          will turn that line into an input line. Conversely, clearing a bit
62          will turn that line into an output.
63
64  reg-names:
65    minItems: 1
66    maxItems: 5
67    items:
68      enum:
69        - dat
70        - set
71        - clr
72        - dirout
73        - dirin
74
75  native-endian: true
76
77  no-output:
78    $ref: /schemas/types.yaml#/definitions/flag
79    description:
80      If this property is present, the controller cannot drive the GPIO lines.
81
82required:
83  - compatible
84  - reg
85  - reg-names
86  - '#gpio-cells'
87  - gpio-controller
88
89additionalProperties: false
90
91examples:
92  - |
93    gpio@1f300010 {
94      compatible = "ni,169445-nand-gpio";
95      reg = <0x1f300010 0x4>;
96      reg-names = "dat";
97      gpio-controller;
98      #gpio-cells = <2>;
99    };
100
101    gpio@e0100000 {
102      compatible = "wd,mbl-gpio";
103      reg-names = "dat";
104      reg = <0xe0100000 0x1>;
105      #gpio-cells = <2>;
106      gpio-controller;
107      no-output;
108    };
109
110    gpio@fffe0406 {
111      compatible = "brcm,bcm6345-gpio";
112      reg-names = "dirout", "dat";
113      reg = <0xfffe0406 2>, <0xfffe040a 2>;
114      native-endian;
115      gpio-controller;
116      #gpio-cells = <2>;
117    };
118