xref: /freebsd/sys/contrib/device-tree/Bindings/display/mediatek/mediatek,hdmi.txt (revision ec0ea6efa1ad229d75c394c1a9b9cac33af2b1d3)
1Mediatek HDMI Encoder
2=====================
3
4The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
5its parallel input.
6
7Required properties:
8- compatible: Should be "mediatek,<chip>-hdmi".
9- the supported chips are mt2701, mt7623 and mt8173
10- reg: Physical base address and length of the controller's registers
11- interrupts: The interrupt signal from the function block.
12- clocks: device clocks
13  See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
14- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
15- phys: phandle link to the HDMI PHY node.
16  See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
17- phy-names: must contain "hdmi"
18- mediatek,syscon-hdmi: phandle link and register offset to the system
19  configuration registers. For mt8173 this must be offset 0x900 into the
20  MMSYS_CONFIG region: <&mmsys 0x900>.
21- ports: A node containing input and output port nodes with endpoint
22  definitions as documented in Documentation/devicetree/bindings/graph.txt.
23- port@0: The input port in the ports node should be connected to a DPI output
24  port.
25- port@1: The output port in the ports node should be connected to the input
26  port of a connector node that contains a ddc-i2c-bus property, or to the
27  input port of an attached bridge chip, such as a SlimPort transmitter.
28
29HDMI CEC
30========
31
32The HDMI CEC controller handles hotplug detection and CEC communication.
33
34Required properties:
35- compatible: Should be "mediatek,<chip>-cec"
36- the supported chips are mt7623 and mt8173
37- reg: Physical base address and length of the controller's registers
38- interrupts: The interrupt signal from the function block.
39- clocks: device clock
40
41HDMI DDC
42========
43
44The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
45The Mediatek's I2C controller is used to interface with I2C devices.
46
47Required properties:
48- compatible: Should be "mediatek,<chip>-hdmi-ddc"
49- the supported chips are mt7623 and mt8173
50- reg: Physical base address and length of the controller's registers
51- clocks: device clock
52- clock-names: Should be "ddc-i2c".
53
54HDMI PHY
55========
56See phy/mediatek,hdmi-phy.yaml
57
58Example:
59
60cec: cec@10013000 {
61	compatible = "mediatek,mt8173-cec";
62	reg = <0 0x10013000 0 0xbc>;
63	interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
64	clocks = <&infracfg CLK_INFRA_CEC>;
65};
66
67hdmi_phy: hdmi-phy@10209100 {
68	compatible = "mediatek,mt8173-hdmi-phy";
69	reg = <0 0x10209100 0 0x24>;
70	clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
71	clock-names = "pll_ref";
72	clock-output-names = "hdmitx_dig_cts";
73	mediatek,ibias = <0xa>;
74	mediatek,ibias_up = <0x1c>;
75	#clock-cells = <0>;
76	#phy-cells = <0>;
77};
78
79hdmi_ddc0: i2c@11012000 {
80	compatible = "mediatek,mt8173-hdmi-ddc";
81	reg = <0 0x11012000 0 0x1c>;
82	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
83	clocks = <&pericfg CLK_PERI_I2C5>;
84	clock-names = "ddc-i2c";
85};
86
87hdmi0: hdmi@14025000 {
88	compatible = "mediatek,mt8173-hdmi";
89	reg = <0 0x14025000 0 0x400>;
90	interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
91	clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
92		 <&mmsys CLK_MM_HDMI_PLLCK>,
93		 <&mmsys CLK_MM_HDMI_AUDIO>,
94		 <&mmsys CLK_MM_HDMI_SPDIF>;
95	clock-names = "pixel", "pll", "bclk", "spdif";
96	pinctrl-names = "default";
97	pinctrl-0 = <&hdmi_pin>;
98	phys = <&hdmi_phy>;
99	phy-names = "hdmi";
100	mediatek,syscon-hdmi = <&mmsys 0x900>;
101	assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
102	assigned-clock-parents = <&hdmi_phy>;
103
104	ports {
105		#address-cells = <1>;
106		#size-cells = <0>;
107
108		port@0 {
109			reg = <0>;
110
111			hdmi0_in: endpoint {
112				remote-endpoint = <&dpi0_out>;
113			};
114		};
115
116		port@1 {
117			reg = <1>;
118
119			hdmi0_out: endpoint {
120				remote-endpoint = <&hdmi_con_in>;
121			};
122		};
123	};
124};
125
126connector {
127	compatible = "hdmi-connector";
128	type = "a";
129	ddc-i2c-bus = <&hdmiddc0>;
130
131	port {
132		hdmi_con_in: endpoint {
133			remote-endpoint = <&hdmi0_out>;
134		};
135	};
136};
137