1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause 3 * 4 * Copyright (c) 2013 Ian Lepore <ian@freebsd.org> 5 * Copyright (c) 2011 Ben Gray <ben.r.gray@gmail.com>. 6 * All rights reserved. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions and the following disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 17 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 18 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 19 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 20 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 21 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 22 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 23 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 24 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 25 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 26 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 27 * SUCH DAMAGE. 28 * 29 */ 30 31 #include <sys/param.h> 32 #include <sys/systm.h> 33 #include <sys/bus.h> 34 #include <sys/gpio.h> 35 #include <sys/kernel.h> 36 #include <sys/malloc.h> 37 #include <sys/module.h> 38 #include <sys/resource.h> 39 #include <sys/rman.h> 40 #include <sys/sysctl.h> 41 #include <sys/taskqueue.h> 42 #include <sys/lock.h> 43 #include <sys/mutex.h> 44 45 #include <arm/ti/ti_cpuid.h> 46 #include <arm/ti/ti_sysc.h> 47 #include "gpio_if.h" 48 49 #include <dev/extres/clk/clk.h> 50 #include <dev/ofw/ofw_bus.h> 51 #include <dev/ofw/ofw_bus_subr.h> 52 53 #include <dev/mmc/bridge.h> 54 #include <dev/mmc/mmcreg.h> 55 #include <dev/mmc/mmcbrvar.h> 56 57 #include <dev/sdhci/sdhci.h> 58 #include <dev/sdhci/sdhci_fdt_gpio.h> 59 #include "sdhci_if.h" 60 61 #include <machine/bus.h> 62 #include <machine/resource.h> 63 #include <machine/intr.h> 64 65 #include "opt_mmccam.h" 66 67 struct ti_sdhci_softc { 68 device_t dev; 69 struct sdhci_fdt_gpio * gpio; 70 struct resource * mem_res; 71 struct resource * irq_res; 72 void * intr_cookie; 73 struct sdhci_slot slot; 74 uint32_t mmchs_reg_off; 75 uint32_t sdhci_reg_off; 76 uint64_t baseclk_hz; 77 uint32_t cmd_and_mode; 78 uint32_t sdhci_clkdiv; 79 boolean_t disable_highspeed; 80 boolean_t force_card_present; 81 boolean_t disable_readonly; 82 }; 83 84 /* 85 * Table of supported FDT compat strings. 86 * 87 * Note that "ti,mmchs" is our own invention, and should be phased out in favor 88 * of the documented names. 89 * 90 * Note that vendor Beaglebone dtsi files use "ti,omap3-hsmmc" for the am335x. 91 */ 92 static struct ofw_compat_data compat_data[] = { 93 {"ti,am335-sdhci", 1}, 94 {"ti,omap3-hsmmc", 1}, 95 {"ti,omap4-hsmmc", 1}, 96 {"ti,mmchs", 1}, 97 {NULL, 0}, 98 }; 99 100 /* 101 * The MMCHS hardware has a few control and status registers at the beginning of 102 * the device's memory map, followed by the standard sdhci register block. 103 * Different SoCs have the register blocks at different offsets from the 104 * beginning of the device. Define some constants to map out the registers we 105 * access, and the various per-SoC offsets. The SDHCI_REG_OFFSET is how far 106 * beyond the MMCHS block the SDHCI block is found; it's the same on all SoCs. 107 */ 108 #define OMAP3_MMCHS_REG_OFFSET 0x000 109 #define OMAP4_MMCHS_REG_OFFSET 0x100 110 #define AM335X_MMCHS_REG_OFFSET 0x100 111 #define SDHCI_REG_OFFSET 0x100 112 113 #define MMCHS_SYSCONFIG 0x010 114 #define MMCHS_SYSCONFIG_RESET (1 << 1) 115 #define MMCHS_SYSSTATUS 0x014 116 #define MMCHS_SYSSTATUS_RESETDONE (1 << 0) 117 #define MMCHS_CON 0x02C 118 #define MMCHS_CON_DW8 (1 << 5) 119 #define MMCHS_CON_DVAL_8_4MS (3 << 9) 120 #define MMCHS_CON_OD (1 << 0) 121 #define MMCHS_SYSCTL 0x12C 122 #define MMCHS_SYSCTL_CLKD_MASK 0x3FF 123 #define MMCHS_SYSCTL_CLKD_SHIFT 6 124 #define MMCHS_SD_CAPA 0x140 125 #define MMCHS_SD_CAPA_VS18 (1 << 26) 126 #define MMCHS_SD_CAPA_VS30 (1 << 25) 127 #define MMCHS_SD_CAPA_VS33 (1 << 24) 128 129 /* Forward declarations, CAM-relataed */ 130 // static void ti_sdhci_cam_poll(struct cam_sim *); 131 // static void ti_sdhci_cam_action(struct cam_sim *, union ccb *); 132 // static int ti_sdhci_cam_settran_settings(struct ti_sdhci_softc *sc, union ccb *); 133 134 static inline uint32_t 135 ti_mmchs_read_4(struct ti_sdhci_softc *sc, bus_size_t off) 136 { 137 138 return (bus_read_4(sc->mem_res, off + sc->mmchs_reg_off)); 139 } 140 141 static inline void 142 ti_mmchs_write_4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) 143 { 144 145 bus_write_4(sc->mem_res, off + sc->mmchs_reg_off, val); 146 } 147 148 static inline uint32_t 149 RD4(struct ti_sdhci_softc *sc, bus_size_t off) 150 { 151 152 return (bus_read_4(sc->mem_res, off + sc->sdhci_reg_off)); 153 } 154 155 static inline void 156 WR4(struct ti_sdhci_softc *sc, bus_size_t off, uint32_t val) 157 { 158 159 bus_write_4(sc->mem_res, off + sc->sdhci_reg_off, val); 160 } 161 162 static uint8_t 163 ti_sdhci_read_1(device_t dev, struct sdhci_slot *slot, bus_size_t off) 164 { 165 struct ti_sdhci_softc *sc = device_get_softc(dev); 166 167 return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xff); 168 } 169 170 static uint16_t 171 ti_sdhci_read_2(device_t dev, struct sdhci_slot *slot, bus_size_t off) 172 { 173 struct ti_sdhci_softc *sc = device_get_softc(dev); 174 uint32_t clkdiv, val32; 175 176 /* 177 * The MMCHS hardware has a non-standard interpretation of the sdclock 178 * divisor bits. It uses the same bit positions as SDHCI 3.0 (15..6) 179 * but doesn't split them into low:high fields. Instead they're a 180 * single number in the range 0..1023 and the number is exactly the 181 * clock divisor (with 0 and 1 both meaning divide by 1). The SDHCI 182 * driver code expects a v2.0 or v3.0 divisor. The shifting and masking 183 * here extracts the MMCHS representation from the hardware word, cleans 184 * those bits out, applies the 2N adjustment, and plugs the result into 185 * the bit positions for the 2.0 or 3.0 divisor in the returned register 186 * value. The ti_sdhci_write_2() routine performs the opposite 187 * transformation when the SDHCI driver writes to the register. 188 */ 189 if (off == SDHCI_CLOCK_CONTROL) { 190 val32 = RD4(sc, SDHCI_CLOCK_CONTROL); 191 clkdiv = ((val32 >> MMCHS_SYSCTL_CLKD_SHIFT) & 192 MMCHS_SYSCTL_CLKD_MASK) / 2; 193 val32 &= ~(MMCHS_SYSCTL_CLKD_MASK << MMCHS_SYSCTL_CLKD_SHIFT); 194 val32 |= (clkdiv & SDHCI_DIVIDER_MASK) << SDHCI_DIVIDER_SHIFT; 195 if (slot->version >= SDHCI_SPEC_300) 196 val32 |= ((clkdiv >> SDHCI_DIVIDER_MASK_LEN) & 197 SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_HI_SHIFT; 198 return (val32 & 0xffff); 199 } 200 201 /* 202 * Standard 32-bit handling of command and transfer mode. 203 */ 204 if (off == SDHCI_TRANSFER_MODE) { 205 return (sc->cmd_and_mode >> 16); 206 } else if (off == SDHCI_COMMAND_FLAGS) { 207 return (sc->cmd_and_mode & 0x0000ffff); 208 } 209 210 return ((RD4(sc, off & ~3) >> (off & 3) * 8) & 0xffff); 211 } 212 213 static uint32_t 214 ti_sdhci_read_4(device_t dev, struct sdhci_slot *slot, bus_size_t off) 215 { 216 struct ti_sdhci_softc *sc = device_get_softc(dev); 217 uint32_t val32; 218 219 val32 = RD4(sc, off); 220 221 /* 222 * If we need to disallow highspeed mode due to the OMAP4 erratum, strip 223 * that flag from the returned capabilities. 224 */ 225 if (off == SDHCI_CAPABILITIES && sc->disable_highspeed) 226 val32 &= ~SDHCI_CAN_DO_HISPD; 227 228 /* 229 * Force the card-present state if necessary. 230 */ 231 if (off == SDHCI_PRESENT_STATE && sc->force_card_present) 232 val32 |= SDHCI_CARD_PRESENT; 233 234 return (val32); 235 } 236 237 static void 238 ti_sdhci_read_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 239 uint32_t *data, bus_size_t count) 240 { 241 struct ti_sdhci_softc *sc = device_get_softc(dev); 242 243 bus_read_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); 244 } 245 246 static void 247 ti_sdhci_write_1(device_t dev, struct sdhci_slot *slot, bus_size_t off, 248 uint8_t val) 249 { 250 struct ti_sdhci_softc *sc = device_get_softc(dev); 251 uint32_t val32; 252 253 #ifdef MMCCAM 254 uint32_t newval32; 255 if (off == SDHCI_HOST_CONTROL) { 256 val32 = ti_mmchs_read_4(sc, MMCHS_CON); 257 newval32 = val32; 258 if (val & SDHCI_CTRL_8BITBUS) { 259 device_printf(dev, "Custom-enabling 8-bit bus\n"); 260 newval32 |= MMCHS_CON_DW8; 261 } else { 262 device_printf(dev, "Custom-disabling 8-bit bus\n"); 263 newval32 &= ~MMCHS_CON_DW8; 264 } 265 if (newval32 != val32) 266 ti_mmchs_write_4(sc, MMCHS_CON, newval32); 267 } 268 #endif 269 val32 = RD4(sc, off & ~3); 270 val32 &= ~(0xff << (off & 3) * 8); 271 val32 |= (val << (off & 3) * 8); 272 273 WR4(sc, off & ~3, val32); 274 } 275 276 static void 277 ti_sdhci_write_2(device_t dev, struct sdhci_slot *slot, bus_size_t off, 278 uint16_t val) 279 { 280 struct ti_sdhci_softc *sc = device_get_softc(dev); 281 uint32_t clkdiv, val32; 282 283 /* 284 * Translate between the hardware and SDHCI 2.0 or 3.0 representations 285 * of the clock divisor. See the comments in ti_sdhci_read_2() for 286 * details. 287 */ 288 if (off == SDHCI_CLOCK_CONTROL) { 289 clkdiv = (val >> SDHCI_DIVIDER_SHIFT) & SDHCI_DIVIDER_MASK; 290 if (slot->version >= SDHCI_SPEC_300) 291 clkdiv |= ((val >> SDHCI_DIVIDER_HI_SHIFT) & 292 SDHCI_DIVIDER_HI_MASK) << SDHCI_DIVIDER_MASK_LEN; 293 clkdiv *= 2; 294 if (clkdiv > MMCHS_SYSCTL_CLKD_MASK) 295 clkdiv = MMCHS_SYSCTL_CLKD_MASK; 296 val32 = RD4(sc, SDHCI_CLOCK_CONTROL); 297 val32 &= 0xffff0000; 298 val32 |= val & ~(MMCHS_SYSCTL_CLKD_MASK << 299 MMCHS_SYSCTL_CLKD_SHIFT); 300 val32 |= clkdiv << MMCHS_SYSCTL_CLKD_SHIFT; 301 WR4(sc, SDHCI_CLOCK_CONTROL, val32); 302 return; 303 } 304 305 /* 306 * Standard 32-bit handling of command and transfer mode. 307 */ 308 if (off == SDHCI_TRANSFER_MODE) { 309 sc->cmd_and_mode = (sc->cmd_and_mode & 0xffff0000) | 310 ((uint32_t)val & 0x0000ffff); 311 return; 312 } else if (off == SDHCI_COMMAND_FLAGS) { 313 sc->cmd_and_mode = (sc->cmd_and_mode & 0x0000ffff) | 314 ((uint32_t)val << 16); 315 WR4(sc, SDHCI_TRANSFER_MODE, sc->cmd_and_mode); 316 return; 317 } 318 319 val32 = RD4(sc, off & ~3); 320 val32 &= ~(0xffff << (off & 3) * 8); 321 val32 |= ((val & 0xffff) << (off & 3) * 8); 322 WR4(sc, off & ~3, val32); 323 } 324 325 static void 326 ti_sdhci_write_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 327 uint32_t val) 328 { 329 struct ti_sdhci_softc *sc = device_get_softc(dev); 330 331 WR4(sc, off, val); 332 } 333 334 static void 335 ti_sdhci_write_multi_4(device_t dev, struct sdhci_slot *slot, bus_size_t off, 336 uint32_t *data, bus_size_t count) 337 { 338 struct ti_sdhci_softc *sc = device_get_softc(dev); 339 340 bus_write_multi_4(sc->mem_res, off + sc->sdhci_reg_off, data, count); 341 } 342 343 static void 344 ti_sdhci_intr(void *arg) 345 { 346 struct ti_sdhci_softc *sc = arg; 347 348 sdhci_generic_intr(&sc->slot); 349 } 350 351 static int 352 ti_sdhci_update_ios(device_t brdev, device_t reqdev) 353 { 354 struct ti_sdhci_softc *sc = device_get_softc(brdev); 355 struct sdhci_slot *slot; 356 struct mmc_ios *ios; 357 uint32_t val32, newval32; 358 359 slot = device_get_ivars(reqdev); 360 ios = &slot->host.ios; 361 362 /* 363 * There is an 8-bit-bus bit in the MMCHS control register which, when 364 * set, overrides the 1 vs 4 bit setting in the standard SDHCI 365 * registers. Set that bit first according to whether an 8-bit bus is 366 * requested, then let the standard driver handle everything else. 367 */ 368 val32 = ti_mmchs_read_4(sc, MMCHS_CON); 369 newval32 = val32; 370 371 if (ios->bus_width == bus_width_8) 372 newval32 |= MMCHS_CON_DW8; 373 else 374 newval32 &= ~MMCHS_CON_DW8; 375 376 if (ios->bus_mode == opendrain) 377 newval32 |= MMCHS_CON_OD; 378 else /* if (ios->bus_mode == pushpull) */ 379 newval32 &= ~MMCHS_CON_OD; 380 381 if (newval32 != val32) 382 ti_mmchs_write_4(sc, MMCHS_CON, newval32); 383 384 return (sdhci_generic_update_ios(brdev, reqdev)); 385 } 386 387 static int 388 ti_sdhci_get_ro(device_t brdev, device_t reqdev) 389 { 390 struct ti_sdhci_softc *sc = device_get_softc(brdev); 391 392 if (sc->disable_readonly) 393 return (0); 394 395 return (sdhci_fdt_gpio_get_readonly(sc->gpio)); 396 } 397 398 static bool 399 ti_sdhci_get_card_present(device_t dev, struct sdhci_slot *slot) 400 { 401 struct ti_sdhci_softc *sc = device_get_softc(dev); 402 403 return (sdhci_fdt_gpio_get_present(sc->gpio)); 404 } 405 406 static int 407 ti_sdhci_detach(device_t dev) 408 { 409 410 /* sdhci_fdt_gpio_teardown(sc->gpio); */ 411 412 return (EBUSY); 413 } 414 415 static int 416 ti_sdhci_hw_init(device_t dev) 417 { 418 struct ti_sdhci_softc *sc = device_get_softc(dev); 419 uint32_t regval; 420 unsigned long timeout; 421 clk_t mmc_clk; 422 int err; 423 424 /* Enable the controller and interface/functional clocks */ 425 if (ti_sysc_clock_enable(device_get_parent(dev)) != 0) { 426 device_printf(dev, "Error: failed to enable MMC clock\n"); 427 return (ENXIO); 428 } 429 430 /* FIXME: Devicetree dosent have any reference to mmc_clk */ 431 err = clk_get_by_name(dev, "mmc_clk", &mmc_clk); 432 if (err) { 433 device_printf(dev, "Can not find mmc_clk\n"); 434 return (ENXIO); 435 } 436 err = clk_get_freq(mmc_clk, &sc->baseclk_hz); 437 if (err) { 438 device_printf(dev, "Cant get mmc_clk frequency\n"); 439 /* AM335x TRM 8.1.6.8 table 8-24 96MHz @ OPP100 */ 440 sc->baseclk_hz = 96000000; 441 } 442 443 /* Issue a softreset to the controller */ 444 ti_mmchs_write_4(sc, MMCHS_SYSCONFIG, MMCHS_SYSCONFIG_RESET); 445 timeout = 1000; 446 while (!(ti_mmchs_read_4(sc, MMCHS_SYSSTATUS) & 447 MMCHS_SYSSTATUS_RESETDONE)) { 448 if (--timeout == 0) { 449 device_printf(dev, 450 "Error: Controller reset operation timed out\n"); 451 break; 452 } 453 DELAY(100); 454 } 455 456 /* 457 * Reset the command and data state machines and also other aspects of 458 * the controller such as bus clock and power. 459 * 460 * If we read the software reset register too fast after writing it we 461 * can get back a zero that means the reset hasn't started yet rather 462 * than that the reset is complete. Per TI recommendations, work around 463 * it by reading until we see the reset bit asserted, then read until 464 * it's clear. We also set the SDHCI_QUIRK_WAITFOR_RESET_ASSERTED quirk 465 * so that the main sdhci driver uses this same logic in its resets. 466 */ 467 ti_sdhci_write_1(dev, NULL, SDHCI_SOFTWARE_RESET, SDHCI_RESET_ALL); 468 timeout = 10000; 469 while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & 470 SDHCI_RESET_ALL) != SDHCI_RESET_ALL) { 471 if (--timeout == 0) { 472 break; 473 } 474 DELAY(1); 475 } 476 timeout = 10000; 477 while ((ti_sdhci_read_1(dev, NULL, SDHCI_SOFTWARE_RESET) & 478 SDHCI_RESET_ALL)) { 479 if (--timeout == 0) { 480 device_printf(dev, 481 "Error: Software reset operation timed out\n"); 482 break; 483 } 484 DELAY(100); 485 } 486 487 /* 488 * The attach() routine has examined fdt data and set flags in 489 * slot.host.caps to reflect what voltages we can handle. Set those 490 * values in the CAPA register. Empirical testing shows that the 491 * values in this register can be overwritten at any time, but the 492 * manual says that these values should only be set once, "before 493 * initialization" whatever that means, and that they survive a reset. 494 */ 495 regval = ti_mmchs_read_4(sc, MMCHS_SD_CAPA); 496 if (sc->slot.host.caps & MMC_OCR_LOW_VOLTAGE) 497 regval |= MMCHS_SD_CAPA_VS18; 498 if (sc->slot.host.caps & (MMC_OCR_290_300 | MMC_OCR_300_310)) 499 regval |= MMCHS_SD_CAPA_VS30; 500 ti_mmchs_write_4(sc, MMCHS_SD_CAPA, regval); 501 502 /* Set initial host configuration (1-bit, std speed, pwr off). */ 503 ti_sdhci_write_1(dev, NULL, SDHCI_HOST_CONTROL, 0); 504 ti_sdhci_write_1(dev, NULL, SDHCI_POWER_CONTROL, 0); 505 506 /* Set the initial controller configuration. */ 507 ti_mmchs_write_4(sc, MMCHS_CON, MMCHS_CON_DVAL_8_4MS); 508 509 return (0); 510 } 511 512 static int 513 ti_sdhci_attach(device_t dev) 514 { 515 struct ti_sdhci_softc *sc = device_get_softc(dev); 516 int rid, err; 517 pcell_t prop; 518 phandle_t node; 519 520 sc->dev = dev; 521 522 /* 523 * Get the MMCHS device id from FDT. Use rev address to identify the unit. 524 */ 525 node = ofw_bus_get_node(dev); 526 527 /* 528 * The hardware can inherently do dual-voltage (1p8v, 3p0v) on the first 529 * device, and only 1p8v on other devices unless an external transceiver 530 * is used. The only way we could know about a transceiver is fdt data. 531 * Note that we have to do this before calling ti_sdhci_hw_init() so 532 * that it can set the right values in the CAPA register. 533 */ 534 sc->slot.host.caps |= MMC_OCR_LOW_VOLTAGE; 535 536 if (OF_hasprop(node, "ti,dual-volt")) { 537 sc->slot.host.caps |= MMC_OCR_290_300 | MMC_OCR_300_310; 538 } 539 540 /* 541 * Set the offset from the device's memory start to the MMCHS registers. 542 * Also for OMAP4 disable high speed mode due to erratum ID i626. 543 */ 544 switch (ti_chip()) { 545 #ifdef SOC_OMAP4 546 case CHIP_OMAP_4: 547 sc->mmchs_reg_off = OMAP4_MMCHS_REG_OFFSET; 548 sc->disable_highspeed = true; 549 break; 550 #endif 551 #ifdef SOC_TI_AM335X 552 case CHIP_AM335X: 553 sc->mmchs_reg_off = AM335X_MMCHS_REG_OFFSET; 554 break; 555 #endif 556 default: 557 panic("Unknown OMAP device\n"); 558 } 559 560 /* 561 * The standard SDHCI registers are at a fixed offset (the same on all 562 * SoCs) beyond the MMCHS registers. 563 */ 564 sc->sdhci_reg_off = sc->mmchs_reg_off + SDHCI_REG_OFFSET; 565 566 /* Resource setup. */ 567 rid = 0; 568 sc->mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 569 RF_ACTIVE); 570 if (!sc->mem_res) { 571 device_printf(dev, "cannot allocate memory window\n"); 572 err = ENXIO; 573 goto fail; 574 } 575 576 rid = 0; 577 sc->irq_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 578 RF_ACTIVE); 579 if (!sc->irq_res) { 580 device_printf(dev, "cannot allocate interrupt\n"); 581 err = ENXIO; 582 goto fail; 583 } 584 585 if (bus_setup_intr(dev, sc->irq_res, INTR_TYPE_BIO | INTR_MPSAFE, 586 NULL, ti_sdhci_intr, sc, &sc->intr_cookie)) { 587 device_printf(dev, "cannot setup interrupt handler\n"); 588 err = ENXIO; 589 goto fail; 590 } 591 592 /* 593 * Set up handling of card-detect and write-protect gpio lines. 594 * 595 * If there is no write protect info in the fdt data, fall back to the 596 * historical practice of assuming that the card is writable. This 597 * works around bad fdt data from the upstream source. The alternative 598 * would be to trust the sdhci controller's PRESENT_STATE register WP 599 * bit, but it may say write protect is in effect when it's not if the 600 * pinmux setup doesn't route the WP signal into the sdchi block. 601 */ 602 sc->gpio = sdhci_fdt_gpio_setup(sc->dev, &sc->slot); 603 604 if (!OF_hasprop(node, "wp-gpios") && !OF_hasprop(node, "wp-disable")) 605 sc->disable_readonly = true; 606 607 /* Initialise the MMCHS hardware. */ 608 err = ti_sdhci_hw_init(dev); 609 if (err != 0) { 610 /* err should already contain ENXIO from ti_sdhci_hw_init() */ 611 goto fail; 612 } 613 614 /* 615 * The capabilities register can only express base clock frequencies in 616 * the range of 0-63MHz for a v2.0 controller. Since our clock runs 617 * faster than that, the hardware sets the frequency to zero in the 618 * register. When the register contains zero, the sdhci driver expects 619 * slot.max_clk to already have the right value in it. 620 */ 621 sc->slot.max_clk = sc->baseclk_hz; 622 623 /* 624 * The MMCHS timeout counter is based on the output sdclock. Tell the 625 * sdhci driver to recalculate the timeout clock whenever the output 626 * sdclock frequency changes. 627 */ 628 sc->slot.quirks |= SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK; 629 630 /* 631 * The MMCHS hardware shifts the 136-bit response data (in violation of 632 * the spec), so tell the sdhci driver not to do the same in software. 633 */ 634 sc->slot.quirks |= SDHCI_QUIRK_DONT_SHIFT_RESPONSE; 635 636 /* 637 * Reset bits are broken, have to wait to see the bits asserted 638 * before waiting to see them de-asserted. 639 */ 640 sc->slot.quirks |= SDHCI_QUIRK_WAITFOR_RESET_ASSERTED; 641 642 /* 643 * The controller waits for busy responses. 644 */ 645 sc->slot.quirks |= SDHCI_QUIRK_WAIT_WHILE_BUSY; 646 647 /* 648 * DMA is not really broken, I just haven't implemented it yet. 649 */ 650 sc->slot.quirks |= SDHCI_QUIRK_BROKEN_DMA; 651 652 /* 653 * Set up the hardware and go. Note that this sets many of the 654 * slot.host.* fields, so we have to do this before overriding any of 655 * those values based on fdt data, below. 656 */ 657 sdhci_init_slot(dev, &sc->slot, 0); 658 659 /* 660 * The SDHCI controller doesn't realize it, but we can support 8-bit 661 * even though we're not a v3.0 controller. If there's an fdt bus-width 662 * property, honor it. 663 */ 664 if (OF_getencprop(node, "bus-width", &prop, sizeof(prop)) > 0) { 665 sc->slot.host.caps &= ~(MMC_CAP_4_BIT_DATA | 666 MMC_CAP_8_BIT_DATA); 667 switch (prop) { 668 case 8: 669 sc->slot.host.caps |= MMC_CAP_8_BIT_DATA; 670 /* FALLTHROUGH */ 671 case 4: 672 sc->slot.host.caps |= MMC_CAP_4_BIT_DATA; 673 break; 674 case 1: 675 break; 676 default: 677 device_printf(dev, "Bad bus-width value %u\n", prop); 678 break; 679 } 680 } 681 682 /* 683 * If the slot is flagged with the non-removable property, set our flag 684 * to always force the SDHCI_CARD_PRESENT bit on. 685 */ 686 node = ofw_bus_get_node(dev); 687 if (OF_hasprop(node, "non-removable")) 688 sc->force_card_present = true; 689 690 bus_generic_probe(dev); 691 bus_generic_attach(dev); 692 693 sdhci_start_slot(&sc->slot); 694 return (0); 695 696 fail: 697 if (sc->intr_cookie) 698 bus_teardown_intr(dev, sc->irq_res, sc->intr_cookie); 699 if (sc->irq_res) 700 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->irq_res); 701 if (sc->mem_res) 702 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->mem_res); 703 704 return (err); 705 } 706 707 static int 708 ti_sdhci_probe(device_t dev) 709 { 710 711 if (!ofw_bus_status_okay(dev)) 712 return (ENXIO); 713 714 if (ofw_bus_search_compatible(dev, compat_data)->ocd_data != 0) { 715 device_set_desc(dev, "TI MMCHS (SDHCI 2.0)"); 716 return (BUS_PROBE_DEFAULT); 717 } 718 719 return (ENXIO); 720 } 721 722 static device_method_t ti_sdhci_methods[] = { 723 /* Device interface */ 724 DEVMETHOD(device_probe, ti_sdhci_probe), 725 DEVMETHOD(device_attach, ti_sdhci_attach), 726 DEVMETHOD(device_detach, ti_sdhci_detach), 727 728 /* Bus interface */ 729 DEVMETHOD(bus_read_ivar, sdhci_generic_read_ivar), 730 DEVMETHOD(bus_write_ivar, sdhci_generic_write_ivar), 731 732 /* MMC bridge interface */ 733 DEVMETHOD(mmcbr_update_ios, ti_sdhci_update_ios), 734 DEVMETHOD(mmcbr_request, sdhci_generic_request), 735 DEVMETHOD(mmcbr_get_ro, ti_sdhci_get_ro), 736 DEVMETHOD(mmcbr_acquire_host, sdhci_generic_acquire_host), 737 DEVMETHOD(mmcbr_release_host, sdhci_generic_release_host), 738 739 /* SDHCI registers accessors */ 740 DEVMETHOD(sdhci_read_1, ti_sdhci_read_1), 741 DEVMETHOD(sdhci_read_2, ti_sdhci_read_2), 742 DEVMETHOD(sdhci_read_4, ti_sdhci_read_4), 743 DEVMETHOD(sdhci_read_multi_4, ti_sdhci_read_multi_4), 744 DEVMETHOD(sdhci_write_1, ti_sdhci_write_1), 745 DEVMETHOD(sdhci_write_2, ti_sdhci_write_2), 746 DEVMETHOD(sdhci_write_4, ti_sdhci_write_4), 747 DEVMETHOD(sdhci_write_multi_4, ti_sdhci_write_multi_4), 748 DEVMETHOD(sdhci_get_card_present, ti_sdhci_get_card_present), 749 750 DEVMETHOD_END 751 }; 752 753 static driver_t ti_sdhci_driver = { 754 "sdhci_ti", 755 ti_sdhci_methods, 756 sizeof(struct ti_sdhci_softc), 757 }; 758 759 DRIVER_MODULE(sdhci_ti, simplebus, ti_sdhci_driver, NULL, NULL); 760 MODULE_DEPEND(sdhci_ti, ti_sysc, 1, 1, 1); 761 SDHCI_DEPEND(sdhci_ti); 762 763 #ifndef MMCCAM 764 MMC_DECLARE_BRIDGE(sdhci_ti); 765 #endif 766