1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause 3 * 4 * Copyright (c) 2013 Ian Lepore <ian@freebsd.org> 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 */ 28 29 #include <sys/cdefs.h> 30 __FBSDID("$FreeBSD$"); 31 32 /* 33 * USBPHY driver for Freescale i.MX6 family of SoCs. 34 */ 35 36 #include "opt_bus.h" 37 38 #include <sys/param.h> 39 #include <sys/systm.h> 40 #include <sys/kernel.h> 41 #include <sys/module.h> 42 #include <sys/bus.h> 43 #include <sys/rman.h> 44 45 #include <dev/ofw/ofw_bus.h> 46 #include <dev/ofw/ofw_bus_subr.h> 47 48 #include <machine/bus.h> 49 50 #include <arm/freescale/imx/imx_ccmvar.h> 51 #include <arm/freescale/imx/imx6_anatopreg.h> 52 #include <arm/freescale/imx/imx6_anatopvar.h> 53 54 /* 55 * Hardware register defines. 56 */ 57 #define PWD_REG 0x0000 58 #define CTRL_STATUS_REG 0x0030 59 #define CTRL_SET_REG 0x0034 60 #define CTRL_CLR_REG 0x0038 61 #define CTRL_TOGGLE_REG 0x003c 62 #define CTRL_SFTRST (1U << 31) 63 #define CTRL_CLKGATE (1 << 30) 64 #define CTRL_ENUTMILEVEL3 (1 << 15) 65 #define CTRL_ENUTMILEVEL2 (1 << 14) 66 67 struct usbphy_softc { 68 device_t dev; 69 struct resource *mem_res; 70 u_int phy_num; 71 }; 72 73 static struct ofw_compat_data compat_data[] = { 74 {"fsl,imx6q-usbphy", true}, 75 {"fsl,imx6ul-usbphy", true}, 76 {NULL, false} 77 }; 78 79 static int 80 usbphy_detach(device_t dev) 81 { 82 struct usbphy_softc *sc; 83 84 sc = device_get_softc(dev); 85 86 if (sc->mem_res != NULL) 87 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->mem_res); 88 89 return (0); 90 } 91 92 static int 93 usbphy_attach(device_t dev) 94 { 95 struct usbphy_softc *sc; 96 int err, regoff, rid; 97 98 sc = device_get_softc(dev); 99 err = 0; 100 101 /* Allocate bus_space resources. */ 102 rid = 0; 103 sc->mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 104 RF_ACTIVE); 105 if (sc->mem_res == NULL) { 106 device_printf(dev, "Cannot allocate memory resources\n"); 107 err = ENXIO; 108 goto out; 109 } 110 111 /* 112 * XXX Totally lame way to get the unit number (but not quite as lame as 113 * adding an ad-hoc property to the fdt data). This works as long as 114 * this driver is used for imx6 only. 115 */ 116 const uint32_t PWD_PHY1_REG_PHYSADDR = 0x020c9000; 117 if (BUS_SPACE_PHYSADDR(sc->mem_res, 0) == PWD_PHY1_REG_PHYSADDR) { 118 sc->phy_num = 0; 119 regoff = 0; 120 } else { 121 sc->phy_num = 1; 122 regoff = 0x60; 123 } 124 125 /* 126 * Based on a note in the u-boot source code, disable charger detection 127 * to avoid degrading the differential signaling on the DP line. Note 128 * that this disables (by design) both charger detection and contact 129 * detection, because of the screwball mix of active-high and active-low 130 * bits in this register. 131 */ 132 imx6_anatop_write_4(IMX6_ANALOG_USB1_CHRG_DETECT + regoff, 133 IMX6_ANALOG_USB_CHRG_DETECT_N_ENABLE | 134 IMX6_ANALOG_USB_CHRG_DETECT_N_CHK_CHRG); 135 136 imx6_anatop_write_4(IMX6_ANALOG_USB1_CHRG_DETECT + regoff, 137 IMX6_ANALOG_USB_CHRG_DETECT_N_ENABLE | 138 IMX6_ANALOG_USB_CHRG_DETECT_N_CHK_CHRG); 139 140 /* XXX Configure the overcurrent detection here. */ 141 142 /* 143 * Turn on the phy clocks. 144 */ 145 imx_ccm_usbphy_enable(dev); 146 147 /* 148 * Set the software reset bit, then clear both it and the clock gate bit 149 * to bring the device out of reset with the clock running. 150 */ 151 bus_write_4(sc->mem_res, CTRL_SET_REG, CTRL_SFTRST); 152 bus_write_4(sc->mem_res, CTRL_CLR_REG, CTRL_SFTRST | CTRL_CLKGATE); 153 154 /* Set UTMI+ level 2+3 bits to enable low and full speed devices. */ 155 bus_write_4(sc->mem_res, CTRL_SET_REG, 156 CTRL_ENUTMILEVEL2 | CTRL_ENUTMILEVEL3); 157 158 /* Power up: clear all bits in the powerdown register. */ 159 bus_write_4(sc->mem_res, PWD_REG, 0); 160 161 err = 0; 162 163 out: 164 165 if (err != 0) 166 usbphy_detach(dev); 167 168 return (err); 169 } 170 171 static int 172 usbphy_probe(device_t dev) 173 { 174 175 if (!ofw_bus_status_okay(dev)) 176 return (ENXIO); 177 178 if (!ofw_bus_search_compatible(dev, compat_data)->ocd_data) 179 return (ENXIO); 180 181 device_set_desc(dev, "Freescale i.MX6 USB PHY"); 182 183 return (BUS_PROBE_DEFAULT); 184 } 185 186 static device_method_t usbphy_methods[] = { 187 /* Device interface */ 188 DEVMETHOD(device_probe, usbphy_probe), 189 DEVMETHOD(device_attach, usbphy_attach), 190 DEVMETHOD(device_detach, usbphy_detach), 191 192 DEVMETHOD_END 193 }; 194 195 static driver_t usbphy_driver = { 196 "usbphy", 197 usbphy_methods, 198 sizeof(struct usbphy_softc) 199 }; 200 201 /* 202 * This driver needs to start before the ehci driver, but later than the usual 203 * "special" drivers like clocks and cpu. Ehci starts at DEFAULT so SUPPORTDEV 204 * is where this driver fits most. 205 */ 206 EARLY_DRIVER_MODULE(usbphy, simplebus, usbphy_driver, 0, 0, 207 BUS_PASS_SUPPORTDEV + BUS_PASS_ORDER_MIDDLE); 208