1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause 3 * 4 * Copyright (c) 2012 Oleksandr Tymoshenko <gonzo@freebsd.org> 5 * Copyright (c) 2013 Luiz Otavio O Souza <loos@freebsd.org> 6 * All rights reserved. 7 * 8 * Redistribution and use in source and binary forms, with or without 9 * modification, are permitted provided that the following conditions 10 * are met: 11 * 1. Redistributions of source code must retain the above copyright 12 * notice, this list of conditions and the following disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 17 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 18 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 19 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 20 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 21 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 22 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 23 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 24 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 25 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 26 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 27 * SUCH DAMAGE. 28 * 29 */ 30 31 #include <sys/param.h> 32 #include <sys/systm.h> 33 #include <sys/bus.h> 34 35 #include <sys/kernel.h> 36 #include <sys/module.h> 37 #include <sys/rman.h> 38 #include <sys/lock.h> 39 #include <sys/mutex.h> 40 #include <sys/sysctl.h> 41 42 #include <machine/bus.h> 43 #include <machine/resource.h> 44 #include <machine/intr.h> 45 46 #include <dev/ofw/ofw_bus.h> 47 #include <dev/ofw/ofw_bus_subr.h> 48 49 #include <dev/spibus/spi.h> 50 #include <dev/spibus/spibusvar.h> 51 52 #include <arm/broadcom/bcm2835/bcm2835_spireg.h> 53 #include <arm/broadcom/bcm2835/bcm2835_spivar.h> 54 55 #include "spibus_if.h" 56 57 static struct ofw_compat_data compat_data[] = { 58 {"broadcom,bcm2835-spi", 1}, 59 {"brcm,bcm2835-spi", 1}, 60 {NULL, 0} 61 }; 62 63 static void bcm_spi_intr(void *); 64 65 #ifdef BCM_SPI_DEBUG 66 static void 67 bcm_spi_printr(device_t dev) 68 { 69 struct bcm_spi_softc *sc; 70 uint32_t reg; 71 72 sc = device_get_softc(dev); 73 reg = BCM_SPI_READ(sc, SPI_CS); 74 device_printf(dev, "CS=%b\n", reg, 75 "\20\1CS0\2CS1\3CPHA\4CPOL\7CSPOL" 76 "\10TA\11DMAEN\12INTD\13INTR\14ADCS\15REN\16LEN" 77 "\21DONE\22RXD\23TXD\24RXR\25RXF\26CSPOL0\27CSPOL1" 78 "\30CSPOL2\31DMA_LEN\32LEN_LONG"); 79 reg = BCM_SPI_READ(sc, SPI_CLK) & SPI_CLK_MASK; 80 if (reg % 2) 81 reg--; 82 if (reg == 0) 83 reg = 65536; 84 device_printf(dev, "CLK=%uMhz/%d=%luhz\n", 85 SPI_CORE_CLK / 1000000, reg, SPI_CORE_CLK / reg); 86 reg = BCM_SPI_READ(sc, SPI_DLEN) & SPI_DLEN_MASK; 87 device_printf(dev, "DLEN=%d\n", reg); 88 reg = BCM_SPI_READ(sc, SPI_LTOH) & SPI_LTOH_MASK; 89 device_printf(dev, "LTOH=%d\n", reg); 90 reg = BCM_SPI_READ(sc, SPI_DC); 91 device_printf(dev, "DC=RPANIC=%#x RDREQ=%#x TPANIC=%#x TDREQ=%#x\n", 92 (reg & SPI_DC_RPANIC_MASK) >> SPI_DC_RPANIC_SHIFT, 93 (reg & SPI_DC_RDREQ_MASK) >> SPI_DC_RDREQ_SHIFT, 94 (reg & SPI_DC_TPANIC_MASK) >> SPI_DC_TPANIC_SHIFT, 95 (reg & SPI_DC_TDREQ_MASK) >> SPI_DC_TDREQ_SHIFT); 96 } 97 #endif 98 99 static void 100 bcm_spi_modifyreg(struct bcm_spi_softc *sc, uint32_t off, uint32_t mask, 101 uint32_t value) 102 { 103 uint32_t reg; 104 105 mtx_assert(&sc->sc_mtx, MA_OWNED); 106 reg = BCM_SPI_READ(sc, off); 107 reg &= ~mask; 108 reg |= value; 109 BCM_SPI_WRITE(sc, off, reg); 110 } 111 112 static int 113 bcm_spi_clock_proc(SYSCTL_HANDLER_ARGS) 114 { 115 struct bcm_spi_softc *sc; 116 uint32_t clk; 117 int error; 118 119 sc = (struct bcm_spi_softc *)arg1; 120 121 BCM_SPI_LOCK(sc); 122 clk = BCM_SPI_READ(sc, SPI_CLK); 123 BCM_SPI_UNLOCK(sc); 124 clk &= 0xffff; 125 if (clk == 0) 126 clk = 65536; 127 clk = SPI_CORE_CLK / clk; 128 129 error = sysctl_handle_int(oidp, &clk, sizeof(clk), req); 130 if (error != 0 || req->newptr == NULL) 131 return (error); 132 133 return (0); 134 } 135 136 static int 137 bcm_spi_cs_bit_proc(SYSCTL_HANDLER_ARGS, uint32_t bit) 138 { 139 struct bcm_spi_softc *sc; 140 uint32_t reg; 141 int error; 142 143 sc = (struct bcm_spi_softc *)arg1; 144 BCM_SPI_LOCK(sc); 145 reg = BCM_SPI_READ(sc, SPI_CS); 146 BCM_SPI_UNLOCK(sc); 147 reg = (reg & bit) ? 1 : 0; 148 149 error = sysctl_handle_int(oidp, ®, sizeof(reg), req); 150 if (error != 0 || req->newptr == NULL) 151 return (error); 152 153 return (0); 154 } 155 156 static int 157 bcm_spi_cpol_proc(SYSCTL_HANDLER_ARGS) 158 { 159 160 return (bcm_spi_cs_bit_proc(oidp, arg1, arg2, req, SPI_CS_CPOL)); 161 } 162 163 static int 164 bcm_spi_cpha_proc(SYSCTL_HANDLER_ARGS) 165 { 166 167 return (bcm_spi_cs_bit_proc(oidp, arg1, arg2, req, SPI_CS_CPHA)); 168 } 169 170 static int 171 bcm_spi_cspol0_proc(SYSCTL_HANDLER_ARGS) 172 { 173 174 return (bcm_spi_cs_bit_proc(oidp, arg1, arg2, req, SPI_CS_CSPOL0)); 175 } 176 177 static int 178 bcm_spi_cspol1_proc(SYSCTL_HANDLER_ARGS) 179 { 180 181 return (bcm_spi_cs_bit_proc(oidp, arg1, arg2, req, SPI_CS_CSPOL1)); 182 } 183 184 static int 185 bcm_spi_cspol2_proc(SYSCTL_HANDLER_ARGS) 186 { 187 188 return (bcm_spi_cs_bit_proc(oidp, arg1, arg2, req, SPI_CS_CSPOL2)); 189 } 190 191 static void 192 bcm_spi_sysctl_init(struct bcm_spi_softc *sc) 193 { 194 struct sysctl_ctx_list *ctx; 195 struct sysctl_oid *tree_node; 196 struct sysctl_oid_list *tree; 197 198 /* 199 * Add system sysctl tree/handlers. 200 */ 201 ctx = device_get_sysctl_ctx(sc->sc_dev); 202 tree_node = device_get_sysctl_tree(sc->sc_dev); 203 tree = SYSCTL_CHILDREN(tree_node); 204 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "clock", 205 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 206 bcm_spi_clock_proc, "IU", "SPI BUS clock frequency"); 207 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "cpol", 208 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 209 bcm_spi_cpol_proc, "IU", "SPI BUS clock polarity"); 210 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "cpha", 211 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 212 bcm_spi_cpha_proc, "IU", "SPI BUS clock phase"); 213 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "cspol0", 214 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 215 bcm_spi_cspol0_proc, "IU", "SPI BUS chip select 0 polarity"); 216 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "cspol1", 217 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 218 bcm_spi_cspol1_proc, "IU", "SPI BUS chip select 1 polarity"); 219 SYSCTL_ADD_PROC(ctx, tree, OID_AUTO, "cspol2", 220 CTLFLAG_RD | CTLTYPE_UINT | CTLFLAG_NEEDGIANT, sc, sizeof(*sc), 221 bcm_spi_cspol2_proc, "IU", "SPI BUS chip select 2 polarity"); 222 } 223 224 static int 225 bcm_spi_probe(device_t dev) 226 { 227 228 if (!ofw_bus_status_okay(dev)) 229 return (ENXIO); 230 231 if (ofw_bus_search_compatible(dev, compat_data)->ocd_data == 0) 232 return (ENXIO); 233 234 device_set_desc(dev, "BCM2708/2835 SPI controller"); 235 236 return (BUS_PROBE_DEFAULT); 237 } 238 239 static int 240 bcm_spi_attach(device_t dev) 241 { 242 struct bcm_spi_softc *sc; 243 int rid; 244 245 if (device_get_unit(dev) != 0) { 246 device_printf(dev, "only one SPI controller supported\n"); 247 return (ENXIO); 248 } 249 250 sc = device_get_softc(dev); 251 sc->sc_dev = dev; 252 253 rid = 0; 254 sc->sc_mem_res = bus_alloc_resource_any(dev, SYS_RES_MEMORY, &rid, 255 RF_ACTIVE); 256 if (!sc->sc_mem_res) { 257 device_printf(dev, "cannot allocate memory window\n"); 258 return (ENXIO); 259 } 260 261 sc->sc_bst = rman_get_bustag(sc->sc_mem_res); 262 sc->sc_bsh = rman_get_bushandle(sc->sc_mem_res); 263 264 rid = 0; 265 sc->sc_irq_res = bus_alloc_resource_any(dev, SYS_RES_IRQ, &rid, 266 RF_ACTIVE); 267 if (!sc->sc_irq_res) { 268 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->sc_mem_res); 269 device_printf(dev, "cannot allocate interrupt\n"); 270 return (ENXIO); 271 } 272 273 /* Hook up our interrupt handler. */ 274 if (bus_setup_intr(dev, sc->sc_irq_res, INTR_TYPE_MISC | INTR_MPSAFE, 275 NULL, bcm_spi_intr, sc, &sc->sc_intrhand)) { 276 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->sc_irq_res); 277 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->sc_mem_res); 278 device_printf(dev, "cannot setup the interrupt handler\n"); 279 return (ENXIO); 280 } 281 282 mtx_init(&sc->sc_mtx, "bcm_spi", NULL, MTX_DEF); 283 284 /* Add sysctl nodes. */ 285 bcm_spi_sysctl_init(sc); 286 287 #ifdef BCM_SPI_DEBUG 288 bcm_spi_printr(dev); 289 #endif 290 291 /* 292 * Enable the SPI controller. Clear the rx and tx FIFO. 293 * Defaults to SPI mode 0. 294 */ 295 BCM_SPI_WRITE(sc, SPI_CS, SPI_CS_CLEAR_RXFIFO | SPI_CS_CLEAR_TXFIFO); 296 297 #ifdef BCM_SPI_DEBUG 298 bcm_spi_printr(dev); 299 #endif 300 301 device_add_child(dev, "spibus", DEVICE_UNIT_ANY); 302 303 return (bus_generic_attach(dev)); 304 } 305 306 static int 307 bcm_spi_detach(device_t dev) 308 { 309 struct bcm_spi_softc *sc; 310 311 bus_generic_detach(dev); 312 313 sc = device_get_softc(dev); 314 mtx_destroy(&sc->sc_mtx); 315 if (sc->sc_intrhand) 316 bus_teardown_intr(dev, sc->sc_irq_res, sc->sc_intrhand); 317 if (sc->sc_irq_res) 318 bus_release_resource(dev, SYS_RES_IRQ, 0, sc->sc_irq_res); 319 if (sc->sc_mem_res) 320 bus_release_resource(dev, SYS_RES_MEMORY, 0, sc->sc_mem_res); 321 322 return (0); 323 } 324 325 static void 326 bcm_spi_fill_fifo(struct bcm_spi_softc *sc) 327 { 328 struct spi_command *cmd; 329 uint32_t cs, written; 330 uint8_t *data; 331 332 cmd = sc->sc_cmd; 333 cs = BCM_SPI_READ(sc, SPI_CS) & (SPI_CS_TA | SPI_CS_TXD); 334 while (sc->sc_written < sc->sc_len && 335 cs == (SPI_CS_TA | SPI_CS_TXD)) { 336 data = (uint8_t *)cmd->tx_cmd; 337 written = sc->sc_written++; 338 if (written >= cmd->tx_cmd_sz) { 339 data = (uint8_t *)cmd->tx_data; 340 written -= cmd->tx_cmd_sz; 341 } 342 BCM_SPI_WRITE(sc, SPI_FIFO, data[written]); 343 cs = BCM_SPI_READ(sc, SPI_CS) & (SPI_CS_TA | SPI_CS_TXD); 344 } 345 } 346 347 static void 348 bcm_spi_drain_fifo(struct bcm_spi_softc *sc) 349 { 350 struct spi_command *cmd; 351 uint32_t cs, read; 352 uint8_t *data; 353 354 cmd = sc->sc_cmd; 355 cs = BCM_SPI_READ(sc, SPI_CS) & SPI_CS_RXD; 356 while (sc->sc_read < sc->sc_len && cs == SPI_CS_RXD) { 357 data = (uint8_t *)cmd->rx_cmd; 358 read = sc->sc_read++; 359 if (read >= cmd->rx_cmd_sz) { 360 data = (uint8_t *)cmd->rx_data; 361 read -= cmd->rx_cmd_sz; 362 } 363 data[read] = BCM_SPI_READ(sc, SPI_FIFO) & 0xff; 364 cs = BCM_SPI_READ(sc, SPI_CS) & SPI_CS_RXD; 365 } 366 } 367 368 static void 369 bcm_spi_intr(void *arg) 370 { 371 struct bcm_spi_softc *sc; 372 373 sc = (struct bcm_spi_softc *)arg; 374 BCM_SPI_LOCK(sc); 375 376 /* Filter stray interrupts. */ 377 if ((sc->sc_flags & BCM_SPI_BUSY) == 0) { 378 BCM_SPI_UNLOCK(sc); 379 return; 380 } 381 382 /* TX - Fill up the FIFO. */ 383 bcm_spi_fill_fifo(sc); 384 385 /* RX - Drain the FIFO. */ 386 bcm_spi_drain_fifo(sc); 387 388 /* Check for end of transfer. */ 389 if (sc->sc_written == sc->sc_len && sc->sc_read == sc->sc_len) { 390 /* Disable interrupts and the SPI engine. */ 391 if ((sc->sc_flags & BCM_SPI_KEEP_CS) == 0) { 392 bcm_spi_modifyreg(sc, SPI_CS, 393 SPI_CS_TA | SPI_CS_INTR | SPI_CS_INTD, 0); 394 } 395 wakeup(sc->sc_dev); 396 } 397 398 BCM_SPI_UNLOCK(sc); 399 } 400 401 static int 402 bcm_spi_transfer(device_t dev, device_t child, struct spi_command *cmd) 403 { 404 struct bcm_spi_softc *sc; 405 uint32_t cs, mode, clock; 406 int err; 407 408 sc = device_get_softc(dev); 409 410 KASSERT(cmd->tx_cmd_sz == cmd->rx_cmd_sz, 411 ("TX/RX command sizes should be equal")); 412 KASSERT(cmd->tx_data_sz == cmd->rx_data_sz, 413 ("TX/RX data sizes should be equal")); 414 415 /* Get the bus speed, mode, and chip select for this child. */ 416 417 spibus_get_cs(child, &cs); 418 if ((cs & (~SPIBUS_CS_HIGH)) > 2) { 419 device_printf(dev, 420 "Invalid chip select %u requested by %s\n", cs, 421 device_get_nameunit(child)); 422 return (EINVAL); 423 } 424 425 spibus_get_clock(child, &clock); 426 if (clock == 0) { 427 device_printf(dev, 428 "Invalid clock %uHz requested by %s\n", clock, 429 device_get_nameunit(child)); 430 return (EINVAL); 431 } 432 433 spibus_get_mode(child, &mode); 434 if (mode > 3) { 435 device_printf(dev, 436 "Invalid mode %u requested by %s\n", mode, 437 device_get_nameunit(child)); 438 return (EINVAL); 439 } 440 441 /* If the controller is in use wait until it is available. */ 442 BCM_SPI_LOCK(sc); 443 if (sc->sc_thread != curthread) 444 while (sc->sc_flags & BCM_SPI_BUSY) 445 mtx_sleep(dev, &sc->sc_mtx, 0, "bcm_spi", 0); 446 447 /* Now we have control over SPI controller. */ 448 sc->sc_flags = BCM_SPI_BUSY; 449 450 if ((cmd->flags & SPI_FLAG_KEEP_CS) != 0) 451 sc->sc_flags |= BCM_SPI_KEEP_CS; 452 453 /* Clear the FIFO. */ 454 if (sc->sc_thread != curthread) 455 bcm_spi_modifyreg(sc, SPI_CS, 456 SPI_CS_CLEAR_RXFIFO | SPI_CS_CLEAR_TXFIFO, 457 SPI_CS_CLEAR_RXFIFO | SPI_CS_CLEAR_TXFIFO); 458 459 sc->sc_thread = curthread; 460 461 /* Save a pointer to the SPI command. */ 462 sc->sc_cmd = cmd; 463 sc->sc_read = 0; 464 sc->sc_written = 0; 465 sc->sc_len = cmd->tx_cmd_sz + cmd->tx_data_sz; 466 467 #ifdef BCM2835_SPI_USE_CS_HIGH /* TODO: for when behavior is correct */ 468 /* 469 * Assign CS polarity first, while the CS indicates 'inactive'. 470 * This will need to set the correct polarity bit based on the 'cs', and 471 * the polarity bit will remain in this state, even after the transaction 472 * is complete. 473 */ 474 if((cs & ~SPIBUS_CS_HIGH) == 0) { 475 bcm_spi_modifyreg(sc, SPI_CS, 476 SPI_CS_CSPOL0, 477 ((cs & (SPIBUS_CS_HIGH)) ? SPI_CS_CSPOL0 : 0)); 478 } 479 else if((cs & ~SPIBUS_CS_HIGH) == 1) { 480 bcm_spi_modifyreg(sc, SPI_CS, 481 SPI_CS_CSPOL1, 482 ((cs & (SPIBUS_CS_HIGH)) ? SPI_CS_CSPOL1 : 0)); 483 } 484 else if((cs & ~SPIBUS_CS_HIGH) == 2) { 485 bcm_spi_modifyreg(sc, SPI_CS, 486 SPI_CS_CSPOL2, 487 ((cs & (SPIBUS_CS_HIGH)) ? SPI_CS_CSPOL2 : 0)); 488 } 489 #endif 490 491 /* 492 * Set the mode in 'SPI_CS' (clock phase and polarity bits). 493 * This must happen before CS output pin is active. 494 * Otherwise, you might glitch and drop the first bit. 495 */ 496 bcm_spi_modifyreg(sc, SPI_CS, 497 SPI_CS_CPOL | SPI_CS_CPHA, 498 ((mode & SPIBUS_MODE_CPHA) ? SPI_CS_CPHA : 0) | 499 ((mode & SPIBUS_MODE_CPOL) ? SPI_CS_CPOL : 0)); 500 501 /* 502 * Set the clock divider in 'SPI_CLK - see 'bcm_spi_clock_proc()'. 503 */ 504 505 /* calculate 'clock' as a divider value from freq */ 506 clock = SPI_CORE_CLK / clock; 507 if (clock <= 1) 508 clock = 2; 509 else if (clock % 2) 510 clock--; 511 if (clock > 0xffff) 512 clock = 0; 513 514 BCM_SPI_WRITE(sc, SPI_CLK, clock); 515 516 /* 517 * Set the CS for this transaction, enable interrupts and announce 518 * we're ready to tx. This will kick off the first interrupt. 519 */ 520 bcm_spi_modifyreg(sc, SPI_CS, 521 SPI_CS_MASK | SPI_CS_TA | SPI_CS_INTR | SPI_CS_INTD, 522 (cs & (~SPIBUS_CS_HIGH)) | /* cs is the lower 2 bits of the reg */ 523 SPI_CS_TA | SPI_CS_INTR | SPI_CS_INTD); 524 525 /* Wait for the transaction to complete. */ 526 err = mtx_sleep(dev, &sc->sc_mtx, 0, "bcm_spi", hz * 2); 527 528 /* Make sure the SPI engine and interrupts are disabled. */ 529 if (!(cmd->flags & SPI_FLAG_KEEP_CS)) { 530 bcm_spi_modifyreg(sc, 531 SPI_CS, SPI_CS_TA | SPI_CS_INTR | SPI_CS_INTD, 0); 532 sc->sc_thread = 0; 533 } 534 535 wakeup_one(dev); 536 sc->sc_flags &= ~BCM_SPI_BUSY; 537 /* Release the controller and wakeup the next thread waiting for it. */ 538 BCM_SPI_UNLOCK(sc); 539 540 /* 541 * Check for transfer timeout. The SPI controller doesn't 542 * return errors. 543 */ 544 if (err == EWOULDBLOCK) { 545 device_printf(sc->sc_dev, "SPI error (timeout)\n"); 546 err = EIO; 547 } 548 549 return (err); 550 } 551 552 static phandle_t 553 bcm_spi_get_node(device_t bus, device_t dev) 554 { 555 556 /* We only have one child, the SPI bus, which needs our own node. */ 557 return (ofw_bus_get_node(bus)); 558 } 559 560 static device_method_t bcm_spi_methods[] = { 561 /* Device interface */ 562 DEVMETHOD(device_probe, bcm_spi_probe), 563 DEVMETHOD(device_attach, bcm_spi_attach), 564 DEVMETHOD(device_detach, bcm_spi_detach), 565 566 /* SPI interface */ 567 DEVMETHOD(spibus_transfer, bcm_spi_transfer), 568 569 /* ofw_bus interface */ 570 DEVMETHOD(ofw_bus_get_node, bcm_spi_get_node), 571 572 DEVMETHOD_END 573 }; 574 575 static driver_t bcm_spi_driver = { 576 "spi", 577 bcm_spi_methods, 578 sizeof(struct bcm_spi_softc), 579 }; 580 581 DRIVER_MODULE(bcm2835_spi, simplebus, bcm_spi_driver, 0, 0); 582