1 /*- 2 * Copyright (c) 2016 Jared McNeill <jmcneill@invisible.ca> 3 * 4 * Redistribution and use in source and binary forms, with or without 5 * modification, are permitted provided that the following conditions 6 * are met: 7 * 1. Redistributions of source code must retain the above copyright 8 * notice, this list of conditions and the following disclaimer. 9 * 2. Redistributions in binary form must reproduce the above copyright 10 * notice, this list of conditions and the following disclaimer in the 11 * documentation and/or other materials provided with the distribution. 12 * 13 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 14 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 15 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 16 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 17 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, 18 * BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; 19 * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED 20 * AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 21 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 22 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 23 * SUCH DAMAGE. 24 */ 25 26 /* 27 * Allwinner RSB (Reduced Serial Bus) and P2WI (Push-Pull Two Wire Interface) 28 */ 29 30 #include <sys/param.h> 31 #include <sys/systm.h> 32 #include <sys/bus.h> 33 #include <sys/rman.h> 34 #include <sys/kernel.h> 35 #include <sys/lock.h> 36 #include <sys/module.h> 37 #include <sys/mutex.h> 38 #include <machine/bus.h> 39 40 #include <dev/ofw/ofw_bus.h> 41 #include <dev/ofw/ofw_bus_subr.h> 42 43 #include <dev/iicbus/iiconf.h> 44 #include <dev/iicbus/iicbus.h> 45 46 #include <dev/clk/clk.h> 47 #include <dev/hwreset/hwreset.h> 48 49 #include "iicbus_if.h" 50 51 #define RSB_CTRL 0x00 52 #define START_TRANS (1 << 7) 53 #define GLOBAL_INT_ENB (1 << 1) 54 #define SOFT_RESET (1 << 0) 55 #define RSB_CCR 0x04 56 #define RSB_INTE 0x08 57 #define RSB_INTS 0x0c 58 #define INT_TRANS_ERR_ID(x) (((x) >> 8) & 0xf) 59 #define INT_LOAD_BSY (1 << 2) 60 #define INT_TRANS_ERR (1 << 1) 61 #define INT_TRANS_OVER (1 << 0) 62 #define INT_MASK (INT_LOAD_BSY|INT_TRANS_ERR|INT_TRANS_OVER) 63 #define RSB_DADDR0 0x10 64 #define RSB_DADDR1 0x14 65 #define RSB_DLEN 0x18 66 #define DLEN_READ (1 << 4) 67 #define RSB_DATA0 0x1c 68 #define RSB_DATA1 0x20 69 #define RSB_PMCR 0x28 70 #define RSB_PMCR_START (1 << 31) 71 #define RSB_PMCR_DATA(x) (x << 16) 72 #define RSB_PMCR_REG(x) (x << 8) 73 #define RSB_CMD 0x2c 74 #define CMD_SRTA 0xe8 75 #define CMD_RD8 0x8b 76 #define CMD_RD16 0x9c 77 #define CMD_RD32 0xa6 78 #define CMD_WR8 0x4e 79 #define CMD_WR16 0x59 80 #define CMD_WR32 0x63 81 #define RSB_DAR 0x30 82 #define DAR_RTA (0xff << 16) 83 #define DAR_RTA_SHIFT 16 84 #define DAR_DA (0xffff << 0) 85 #define DAR_DA_SHIFT 0 86 87 #define RSB_MAXLEN 8 88 #define RSB_RESET_RETRY 100 89 #define RSB_I2C_TIMEOUT hz 90 91 #define RSB_ADDR_PMIC_PRIMARY 0x3a3 92 #define RSB_ADDR_PMIC_SECONDARY 0x745 93 #define RSB_ADDR_PERIPH_IC 0xe89 94 95 #define PMIC_MODE_REG 0x3e 96 #define PMIC_MODE_I2C 0x00 97 #define PMIC_MODE_RSB 0x7c 98 99 #define A31_P2WI 1 100 #define A23_RSB 2 101 102 static struct ofw_compat_data compat_data[] = { 103 { "allwinner,sun6i-a31-p2wi", A31_P2WI }, 104 { "allwinner,sun8i-a23-rsb", A23_RSB }, 105 { NULL, 0 } 106 }; 107 108 static struct resource_spec rsb_spec[] = { 109 { SYS_RES_MEMORY, 0, RF_ACTIVE }, 110 { -1, 0 } 111 }; 112 113 /* 114 * Device address to Run-time address mappings. 115 * 116 * Run-time address (RTA) is an 8-bit value used to address the device during 117 * a read or write transaction. The following are valid RTAs: 118 * 0x17 0x2d 0x3a 0x4e 0x59 0x63 0x74 0x8b 0x9c 0xa6 0xb1 0xc5 0xd2 0xe8 0xff 119 * 120 * Allwinner uses RTA 0x2d for the primary PMIC, 0x3a for the secondary PMIC, 121 * and 0x4e for the peripheral IC (where applicable). 122 */ 123 static const struct { 124 uint16_t addr; 125 uint8_t rta; 126 } rsb_rtamap[] = { 127 { .addr = RSB_ADDR_PMIC_PRIMARY, .rta = 0x2d }, 128 { .addr = RSB_ADDR_PMIC_SECONDARY, .rta = 0x3a }, 129 { .addr = RSB_ADDR_PERIPH_IC, .rta = 0x4e }, 130 { .addr = 0, .rta = 0 } 131 }; 132 133 struct rsb_softc { 134 struct resource *res; 135 struct mtx mtx; 136 clk_t clk; 137 hwreset_t rst; 138 device_t iicbus; 139 int busy; 140 uint32_t status; 141 uint16_t cur_addr; 142 int type; 143 144 struct iic_msg *msg; 145 }; 146 147 #define RSB_LOCK(sc) mtx_lock(&(sc)->mtx) 148 #define RSB_UNLOCK(sc) mtx_unlock(&(sc)->mtx) 149 #define RSB_ASSERT_LOCKED(sc) mtx_assert(&(sc)->mtx, MA_OWNED) 150 #define RSB_READ(sc, reg) bus_read_4((sc)->res, (reg)) 151 #define RSB_WRITE(sc, reg, val) bus_write_4((sc)->res, (reg), (val)) 152 153 static phandle_t 154 rsb_get_node(device_t bus, device_t dev) 155 { 156 return (ofw_bus_get_node(bus)); 157 } 158 159 static int 160 rsb_reset(device_t dev, u_char speed, u_char addr, u_char *oldaddr) 161 { 162 struct rsb_softc *sc; 163 int retry; 164 165 sc = device_get_softc(dev); 166 167 RSB_LOCK(sc); 168 169 /* Write soft-reset bit and wait for it to self-clear. */ 170 RSB_WRITE(sc, RSB_CTRL, SOFT_RESET); 171 for (retry = RSB_RESET_RETRY; retry > 0; retry--) 172 if ((RSB_READ(sc, RSB_CTRL) & SOFT_RESET) == 0) 173 break; 174 175 RSB_UNLOCK(sc); 176 177 if (retry == 0) { 178 device_printf(dev, "soft reset timeout\n"); 179 return (ETIMEDOUT); 180 } 181 182 return (IIC_ENOADDR); 183 } 184 185 static uint32_t 186 rsb_encode(const uint8_t *buf, u_int len, u_int off) 187 { 188 uint32_t val; 189 u_int n; 190 191 val = 0; 192 for (n = off; n < MIN(len, 4 + off); n++) 193 val |= ((uint32_t)buf[n] << ((n - off) * NBBY)); 194 195 return val; 196 } 197 198 static void 199 rsb_decode(const uint32_t val, uint8_t *buf, u_int len, u_int off) 200 { 201 u_int n; 202 203 for (n = off; n < MIN(len, 4 + off); n++) 204 buf[n] = (val >> ((n - off) * NBBY)) & 0xff; 205 } 206 207 static int 208 rsb_start(device_t dev) 209 { 210 struct rsb_softc *sc; 211 int error, retry; 212 213 sc = device_get_softc(dev); 214 215 RSB_ASSERT_LOCKED(sc); 216 217 /* Start the transfer */ 218 RSB_WRITE(sc, RSB_CTRL, GLOBAL_INT_ENB | START_TRANS); 219 220 /* Wait for transfer to complete */ 221 error = ETIMEDOUT; 222 for (retry = RSB_I2C_TIMEOUT; retry > 0; retry--) { 223 sc->status |= RSB_READ(sc, RSB_INTS); 224 if ((sc->status & INT_TRANS_OVER) != 0) { 225 error = 0; 226 break; 227 } 228 DELAY((1000 * hz) / RSB_I2C_TIMEOUT); 229 } 230 if (error == 0 && (sc->status & INT_TRANS_OVER) == 0) { 231 device_printf(dev, "transfer error, status 0x%08x\n", 232 sc->status); 233 error = EIO; 234 } 235 236 return (error); 237 238 } 239 240 static int 241 rsb_set_rta(device_t dev, uint16_t addr) 242 { 243 struct rsb_softc *sc; 244 uint8_t rta; 245 int i; 246 247 sc = device_get_softc(dev); 248 249 RSB_ASSERT_LOCKED(sc); 250 251 /* Lookup run-time address for given device address */ 252 for (rta = 0, i = 0; rsb_rtamap[i].rta != 0; i++) 253 if (rsb_rtamap[i].addr == addr) { 254 rta = rsb_rtamap[i].rta; 255 break; 256 } 257 if (rta == 0) { 258 device_printf(dev, "RTA not known for address %#x\n", addr); 259 return (ENXIO); 260 } 261 262 /* Set run-time address */ 263 RSB_WRITE(sc, RSB_INTS, RSB_READ(sc, RSB_INTS)); 264 RSB_WRITE(sc, RSB_DAR, (addr << DAR_DA_SHIFT) | (rta << DAR_RTA_SHIFT)); 265 RSB_WRITE(sc, RSB_CMD, CMD_SRTA); 266 267 return (rsb_start(dev)); 268 } 269 270 static int 271 rsb_transfer(device_t dev, struct iic_msg *msgs, uint32_t nmsgs) 272 { 273 struct rsb_softc *sc; 274 uint32_t daddr[2], data[2], dlen; 275 uint16_t device_addr; 276 uint8_t cmd; 277 int error; 278 279 sc = device_get_softc(dev); 280 281 /* 282 * P2WI and RSB are not really I2C or SMBus controllers, so there are 283 * some restrictions imposed by the driver. 284 * 285 * Transfers must contain exactly two messages. The first is always 286 * a write, containing a single data byte offset. Data will either 287 * be read from or written to the corresponding data byte in the 288 * second message. The slave address in both messages must be the 289 * same. 290 */ 291 if (nmsgs != 2 || (msgs[0].flags & IIC_M_RD) == IIC_M_RD || 292 (msgs[0].slave >> 1) != (msgs[1].slave >> 1) || 293 msgs[0].len != 1 || msgs[1].len > RSB_MAXLEN) 294 return (EINVAL); 295 296 /* The RSB controller can read or write 1, 2, or 4 bytes at a time. */ 297 if (sc->type == A23_RSB) { 298 if ((msgs[1].flags & IIC_M_RD) != 0) { 299 switch (msgs[1].len) { 300 case 1: 301 cmd = CMD_RD8; 302 break; 303 case 2: 304 cmd = CMD_RD16; 305 break; 306 case 4: 307 cmd = CMD_RD32; 308 break; 309 default: 310 return (EINVAL); 311 } 312 } else { 313 switch (msgs[1].len) { 314 case 1: 315 cmd = CMD_WR8; 316 break; 317 case 2: 318 cmd = CMD_WR16; 319 break; 320 case 4: 321 cmd = CMD_WR32; 322 break; 323 default: 324 return (EINVAL); 325 } 326 } 327 } 328 329 RSB_LOCK(sc); 330 while (sc->busy) 331 mtx_sleep(sc, &sc->mtx, 0, "i2cbuswait", 0); 332 sc->busy = 1; 333 sc->status = 0; 334 335 /* Select current run-time address if necessary */ 336 if (sc->type == A23_RSB) { 337 device_addr = msgs[0].slave >> 1; 338 if (sc->cur_addr != device_addr) { 339 error = rsb_set_rta(dev, device_addr); 340 if (error != 0) 341 goto done; 342 sc->cur_addr = device_addr; 343 sc->status = 0; 344 } 345 } 346 347 /* Clear interrupt status */ 348 RSB_WRITE(sc, RSB_INTS, RSB_READ(sc, RSB_INTS)); 349 350 /* Program data access address registers */ 351 daddr[0] = rsb_encode(msgs[0].buf, msgs[0].len, 0); 352 RSB_WRITE(sc, RSB_DADDR0, daddr[0]); 353 354 /* Write data */ 355 if ((msgs[1].flags & IIC_M_RD) == 0) { 356 data[0] = rsb_encode(msgs[1].buf, msgs[1].len, 0); 357 RSB_WRITE(sc, RSB_DATA0, data[0]); 358 } 359 360 /* Set command type for RSB */ 361 if (sc->type == A23_RSB) 362 RSB_WRITE(sc, RSB_CMD, cmd); 363 364 /* Program data length register and transfer direction */ 365 dlen = msgs[0].len - 1; 366 if ((msgs[1].flags & IIC_M_RD) == IIC_M_RD) 367 dlen |= DLEN_READ; 368 RSB_WRITE(sc, RSB_DLEN, dlen); 369 370 /* Start transfer */ 371 error = rsb_start(dev); 372 if (error != 0) 373 goto done; 374 375 /* Read data */ 376 if ((msgs[1].flags & IIC_M_RD) == IIC_M_RD) { 377 data[0] = RSB_READ(sc, RSB_DATA0); 378 rsb_decode(data[0], msgs[1].buf, msgs[1].len, 0); 379 } 380 381 done: 382 sc->msg = NULL; 383 sc->busy = 0; 384 wakeup(sc); 385 RSB_UNLOCK(sc); 386 387 return (error); 388 } 389 390 static int 391 rsb_probe(device_t dev) 392 { 393 if (!ofw_bus_status_okay(dev)) 394 return (ENXIO); 395 396 switch (ofw_bus_search_compatible(dev, compat_data)->ocd_data) { 397 case A23_RSB: 398 device_set_desc(dev, "Allwinner RSB"); 399 break; 400 case A31_P2WI: 401 device_set_desc(dev, "Allwinner P2WI"); 402 break; 403 default: 404 return (ENXIO); 405 } 406 407 return (BUS_PROBE_DEFAULT); 408 } 409 410 static int 411 rsb_attach(device_t dev) 412 { 413 struct rsb_softc *sc; 414 int error; 415 416 sc = device_get_softc(dev); 417 mtx_init(&sc->mtx, device_get_nameunit(dev), "rsb", MTX_DEF); 418 419 sc->type = ofw_bus_search_compatible(dev, compat_data)->ocd_data; 420 421 if (clk_get_by_ofw_index(dev, 0, 0, &sc->clk) == 0) { 422 error = clk_enable(sc->clk); 423 if (error != 0) { 424 device_printf(dev, "cannot enable clock\n"); 425 goto fail; 426 } 427 } 428 if (hwreset_get_by_ofw_idx(dev, 0, 0, &sc->rst) == 0) { 429 error = hwreset_deassert(sc->rst); 430 if (error != 0) { 431 device_printf(dev, "cannot de-assert reset\n"); 432 goto fail; 433 } 434 } 435 436 if (bus_alloc_resources(dev, rsb_spec, &sc->res) != 0) { 437 device_printf(dev, "cannot allocate resources for device\n"); 438 error = ENXIO; 439 goto fail; 440 } 441 442 /* Set the PMIC into RSB mode as ATF might have leave it in I2C mode */ 443 RSB_WRITE(sc, RSB_PMCR, RSB_PMCR_REG(PMIC_MODE_REG) | RSB_PMCR_DATA(PMIC_MODE_RSB) | RSB_PMCR_START); 444 445 sc->iicbus = device_add_child(dev, "iicbus", DEVICE_UNIT_ANY); 446 if (sc->iicbus == NULL) { 447 device_printf(dev, "cannot add iicbus child device\n"); 448 error = ENXIO; 449 goto fail; 450 } 451 452 bus_attach_children(dev); 453 454 return (0); 455 456 fail: 457 bus_release_resources(dev, rsb_spec, &sc->res); 458 if (sc->rst != NULL) 459 hwreset_release(sc->rst); 460 if (sc->clk != NULL) 461 clk_release(sc->clk); 462 mtx_destroy(&sc->mtx); 463 return (error); 464 } 465 466 static device_method_t rsb_methods[] = { 467 /* Device interface */ 468 DEVMETHOD(device_probe, rsb_probe), 469 DEVMETHOD(device_attach, rsb_attach), 470 471 /* Bus interface */ 472 DEVMETHOD(bus_setup_intr, bus_generic_setup_intr), 473 DEVMETHOD(bus_teardown_intr, bus_generic_teardown_intr), 474 DEVMETHOD(bus_alloc_resource, bus_generic_alloc_resource), 475 DEVMETHOD(bus_release_resource, bus_generic_release_resource), 476 DEVMETHOD(bus_activate_resource, bus_generic_activate_resource), 477 DEVMETHOD(bus_deactivate_resource, bus_generic_deactivate_resource), 478 DEVMETHOD(bus_adjust_resource, bus_generic_adjust_resource), 479 DEVMETHOD(bus_set_resource, bus_generic_rl_set_resource), 480 DEVMETHOD(bus_get_resource, bus_generic_rl_get_resource), 481 482 /* OFW methods */ 483 DEVMETHOD(ofw_bus_get_node, rsb_get_node), 484 485 /* iicbus interface */ 486 DEVMETHOD(iicbus_callback, iicbus_null_callback), 487 DEVMETHOD(iicbus_reset, rsb_reset), 488 DEVMETHOD(iicbus_transfer, rsb_transfer), 489 490 DEVMETHOD_END 491 }; 492 493 static driver_t rsb_driver = { 494 "iichb", 495 rsb_methods, 496 sizeof(struct rsb_softc), 497 }; 498 499 EARLY_DRIVER_MODULE(iicbus, rsb, iicbus_driver, 0, 0, 500 BUS_PASS_SUPPORTDEV + BUS_PASS_ORDER_MIDDLE); 501 EARLY_DRIVER_MODULE(rsb, simplebus, rsb_driver, 0, 0, 502 BUS_PASS_SUPPORTDEV + BUS_PASS_ORDER_MIDDLE); 503 MODULE_VERSION(rsb, 1); 504 MODULE_DEPEND(rsb, iicbus, 1, 1, 1); 505 SIMPLEBUS_PNP_INFO(compat_data); 506