1.\" Copyright (c) 2003 Marcel Moolenaar 2.\" All rights reserved. 3.\" 4.\" Redistribution and use in source and binary forms, with or without 5.\" modification, are permitted provided that the following conditions 6.\" are met: 7.\" 8.\" 1. Redistributions of source code must retain the above copyright 9.\" notice, this list of conditions and the following disclaimer. 10.\" 2. Redistributions in binary form must reproduce the above copyright 11.\" notice, this list of conditions and the following disclaimer in the 12.\" documentation and/or other materials provided with the distribution. 13.\" 14.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 15.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 16.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 17.\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 18.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 19.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 20.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 21.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 22.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 23.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 24.\" SUCH DAMAGE. 25.\" 26.\" $FreeBSD$ 27.\" 28.Dd January 6, 2005 29.Dt BUS_CONFIG_INTR 9 30.Os 31.\" 32.Sh NAME 33.Nm BUS_CONFIG_INTR 34.Nd "configure interrupt polarity and trigger mode" 35.\" 36.Sh SYNOPSIS 37.In sys/param.h 38.In sys/bus.h 39.Ft int 40.Fo BUS_CONFIG_INTR 41.Fa "device_t dev" "int irq" "enum intr_trigger trig" "enum intr_polarity pol" 42.Fc 43.\" 44.Sh DESCRIPTION 45The 46.Fn BUS_CONFIG_INTR 47method allows bus or device drivers to provide interrupt polarity and trigger 48mode to parent busses. 49This typically bubbles all the way up to the root bus (e.g.\& nexus) where the 50necessary actions are taken to actually program the hardware. 51Since the 52.Fn BUS_CONFIG_INTR 53method takes an interrupt number, it is assumed but not necessarily required 54that it is called prior to 55.Xr BUS_SETUP_INTR 9 . 56.Pp 57The 58.Fa trig 59argument can be one of: 60.Bl -tag -width ".Dv INTR_TRIGGER_CONFORM" 61.It Dv INTR_TRIGGER_CONFORM 62The interrupt trigger mode is standard for the bus to which the device is 63attached. 64.It Dv INTR_TRIGGER_EDGE 65The interrupt is edge triggered. 66This means that the interrupt is raised by the rising edge of the signal on 67the interrupt line. 68The signal typically reverts to the original state so as to cause a spike. 69.It Dv INTR_TRIGGER_LEVEL 70The interrupt is level triggered. 71This means that the interrupt is raised when the signal on the interrupt line 72transitions and remains unchanged after that until the interrupt has been 73serviced, after which the signal transitions back. 74.El 75.Pp 76The 77.Fa pol 78argument can be any one of: 79.Bl -tag -width ".Dv INTR_POLARITY_CONFORM" 80.It Dv INTR_POLARITY_CONFORM 81The interrupt polarity is standard for the bus to which the device is attached. 82.It Dv INTR_POLARITY_HIGH 83The interrupt is activated by a high voltage on the interrupt line. 84.It Dv INTR_POLARITY_LOW 85The interrupt is activated by a low voltage on the interrupt line. 86.El 87.\" 88.Sh RETURN VALUES 89Zero is returned on success, otherwise an appropriate error is returned. 90.\" 91.Sh SEE ALSO 92.Xr BUS_SETUP_INTR 9 , 93.Xr BUS_TEARDOWN_INTR 9 , 94.Xr device 9 , 95.Xr driver 9 96.\" 97.Sh HISTORY 98The 99.Fn BUS_CONFIG_INTR 100method first appeared in 101.Fx 5.2 . 102.\" 103.Sh AUTHORS 104This manual page was written by 105.An Marcel Moolenaar Aq Mt marcel@xcllnt.net . 106