1.\" Copyright (c) 2013, Luiz Otavio O Souza <loos@FreeBSD.org> 2.\" All rights reserved. 3.\" 4.\" Redistribution and use in source and binary forms, with or without 5.\" modification, are permitted provided that the following conditions 6.\" are met: 7.\" 1. Redistributions of source code must retain the above copyright 8.\" notice, this list of conditions and the following disclaimer. 9.\" 2. Redistributions in binary form must reproduce the above copyright 10.\" notice, this list of conditions and the following disclaimer in the 11.\" documentation and/or other materials provided with the distribution. 12.\" 13.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 14.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 15.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 16.\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 17.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 18.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 19.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 20.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 21.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 22.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 23.\" SUCH DAMAGE. 24.\" 25.\" $FreeBSD$ 26.\" 27.Dd February 13, 2014 28.Dt GPIOIIC 4 29.Os 30.Sh NAME 31.Nm gpioiic 32.Nd GPIO I2C bit-banging device driver 33.Sh SYNOPSIS 34To compile this driver into the kernel, 35place the following lines in your 36kernel configuration file: 37.Bd -ragged -offset indent 38.Cd "device gpio" 39.Cd "device gpioiic" 40.Cd "device iic" 41.Cd "device iicbb" 42.Cd "device iicbus" 43.Ed 44.Sh DESCRIPTION 45The 46.Nm 47driver provides an IIC bit-banging interface using two GPIO pins for the 48SCL and SDA on the 49.Nm gpiobus . 50.Nm 51implements an open collector kind of output, as recommended by the standard, 52when driving the pins on the 53.Nm gpiobus , 54i.e, they are never switched to the logical value of '1', 55or they are '0' or simply open (Hi-Z/tri-state). 56So the pullup resistors are required so 57.Nm 58can work. 59.Pp 60On a 61.Xr device.hints 5 62based system, like 63.Li MIPS , 64these values are configurable for the 65.Nm : 66.Bl -tag -width ".Va hint.gpioiic.%d.atXXX" 67.It Va hint.gpioiic.%d.at 68The 69.Nm gpiobus 70you are attaching to. 71Normally just gpiobus0. 72.It Va hint.gpioiic.%d.pins 73This is a bitmask of the pins on the 74.Nm gpiobus 75that are to be used for SCLOCK and SDATA from the GPIO IIC 76bit-banging bus. 77To configure pin 0 and 7, use the bitmask of 780b10000001 and convert it to a hexadecimal value of 0x0081. 79Please note that this mask should only ever have two bits set 80(any other bits - i.e., pins - will be ignored). 81.It Va hint.gpioiic.%d.scl 82Indicates which bit in the 83.Va hint.gpioiic.%d.pins 84should be used as the SCLOCK 85source. 86Optional, defaults to 0. 87.It Va hint.gpioiic.%d.sda 88Indicates which bit in the 89.Va hint.gpioiic.%d.pins 90should be used as the SDATA 91source. 92Optional, defaults to 1. 93.El 94.Pp 95On a 96.Xr FDT 4 97based system, like 98.Li ARM , 99the DTS part for a 100.Nm gpioiic 101device usually looks like: 102.Bd -literal 103gpio: gpio { 104 105 gpio-controller; 106 ... 107 108 gpioiic0 { 109 compatible = "gpioiic"; 110 /* 111 * Attach to GPIO pins 21 and 22. Set them 112 * initially as inputs. 113 */ 114 gpios = <&gpio 21 1 0 115 &gpio 22 1 0>; 116 scl = <0>; /* GPIO pin 21 - optional */ 117 sda = <1>; /* GPIO pin 22 - optional */ 118 119 /* This is an example of a gpioiic child. */ 120 gpioiic-child0 { 121 compatible = "lm75"; 122 i2c-address = <0x4f>; 123 }; 124 }; 125}; 126.Ed 127.Pp 128Where: 129.Bl -tag -width ".Va compatible" 130.It Va compatible 131Should always be set to "gpioiic". 132.It Va gpios 133The 134.Va gpios 135property indicates which GPIO pins should be used for SCLOCK and SDATA 136on the GPIO IIC bit-banging bus. 137For more details about the 138.Va gpios 139property, please consult 140.Pa /usr/src/sys/boot/fdt/dts/bindings-gpio.txt . 141.It Va scl 142The 143.Va scl 144option indicates which bit in the 145.Va gpios 146should be used as the SCLOCK source. 147Optional, defaults to 0. 148.It Va sda 149The 150.Va sda 151option indicates which bit in the 152.Va gpios 153should be used as the SDATA source. 154Optional, defaults to 1. 155.El 156.Sh SEE ALSO 157.Xr fdt 4 , 158.Xr gpio 4 , 159.Xr gpioled 4 , 160.Xr iic 4 , 161.Xr iicbb 4 , 162.Xr iicbus 4 163.Sh HISTORY 164The 165.Nm 166manual page first appeared in 167.Fx 11.0 . 168.Sh AUTHORS 169This 170manual page was written by 171.An Luiz Otavio O Souza . 172