xref: /freebsd/contrib/wpa/wpa_supplicant/ChangeLog (revision 86aa9539fef591a363b06a0ebd3aa7a07f4c1579)

ChangeLog for wpa_supplicant

2019-04-21 - v2.8
	* SAE changes
	  - added support for SAE Password Identifier
	  - changed default configuration to enable only groups 19, 20, 21
	    (i.e., disable groups 25 and 26) and disable all unsuitable groups
	    completely based on REVmd changes
	  - do not regenerate PWE unnecessarily when the AP uses the
	    anti-clogging token mechanisms
	  - fixed some association cases where both SAE and FT-SAE were enabled
	    on both the station and the selected AP
	  - started to prefer FT-SAE over SAE AKM if both are enabled
	  - started to prefer FT-SAE over FT-PSK if both are enabled
	  - fixed FT-SAE when SAE PMKSA caching is used
	  - reject use of unsuitable groups based on new implementation guidance
	    in REVmd (allow only FFC groups with prime >= 3072 bits and ECC
	    groups with prime >= 256)
	  - minimize timing and memory use differences in PWE derivation
	    [https://w1.fi/security/2019-1/] (CVE-2019-9494)
	* EAP-pwd changes
	  - minimize timing and memory use differences in PWE derivation
	    [https://w1.fi/security/2019-2/] (CVE-2019-9495)
	  - verify server scalar/element
	    [https://w1.fi/security/2019-4/] (CVE-2019-9499)
	  - fix message reassembly issue with unexpected fragment
	    [https://w1.fi/security/2019-5/]
	  - enforce rand,mask generation rules more strictly
	  - fix a memory leak in PWE derivation
	  - disallow ECC groups with a prime under 256 bits (groups 25, 26, and
	    27)
	* fixed CONFIG_IEEE80211R=y (FT) build without CONFIG_FILS=y
	* Hotspot 2.0 changes
	  - do not indicate release number that is higher than the one
	    AP supports
	  - added support for release number 3
	  - enable PMF automatically for network profiles created from
	    credentials
	* fixed OWE network profile saving
	* fixed DPP network profile saving
	* added support for RSN operating channel validation
	  (CONFIG_OCV=y and network profile parameter ocv=1)
	* added Multi-AP backhaul STA support
	* fixed build with LibreSSL
	* number of MKA/MACsec fixes and extensions
	* extended domain_match and domain_suffix_match to allow list of values
	* fixed dNSName matching in domain_match and domain_suffix_match when
	  using wolfSSL
	* started to prefer FT-EAP-SHA384 over WPA-EAP-SUITE-B-192 AKM if both
	  are enabled
	* extended nl80211 Connect and external authentication to support
	  SAE, FT-SAE, FT-EAP-SHA384
	* fixed KEK2 derivation for FILS+FT
	* extended client_cert file to allow loading of a chain of PEM
	  encoded certificates
	* extended beacon reporting functionality
	* extended D-Bus interface with number of new properties
	* fixed a regression in FT-over-DS with mac80211-based drivers
	* OpenSSL: allow systemwide policies to be overridden
	* extended driver flags indication for separate 802.1X and PSK
	  4-way handshake offload capability
	* added support for random P2P Device/Interface Address use
	* extended PEAP to derive EMSK to enable use with ERP/FILS
	* extended WPS to allow SAE configuration to be added automatically
	  for PSK (wps_cred_add_sae=1)
	* removed support for the old D-Bus interface (CONFIG_CTRL_IFACE_DBUS)
	* extended domain_match and domain_suffix_match to allow list of values
	* added a RSN workaround for misbehaving PMF APs that advertise
	  IGTK/BIP KeyID using incorrect byte order
	* fixed PTK rekeying with FILS and FT

2018-12-02 - v2.7
	* fixed WPA packet number reuse with replayed messages and key
	  reinstallation
	  [https://w1.fi/security/2017-1/] (CVE-2017-13077, CVE-2017-13078,
	  CVE-2017-13079, CVE-2017-13080, CVE-2017-13081, CVE-2017-13082,
	  CVE-2017-13086, CVE-2017-13087, CVE-2017-13088)
	* fixed unauthenticated EAPOL-Key decryption in wpa_supplicant
	  [https://w1.fi/security/2018-1/] (CVE-2018-14526)
	* added support for FILS (IEEE 802.11ai) shared key authentication
	* added support for OWE (Opportunistic Wireless Encryption, RFC 8110;
	  and transition mode defined by WFA)
	* added support for DPP (Wi-Fi Device Provisioning Protocol)
	* added support for RSA 3k key case with Suite B 192-bit level
	* fixed Suite B PMKSA caching not to update PMKID during each 4-way
	  handshake
	* fixed EAP-pwd pre-processing with PasswordHashHash
	* added EAP-pwd client support for salted passwords
	* fixed a regression in TDLS prohibited bit validation
	* started to use estimated throughput to avoid undesired signal
	  strength based roaming decision
	* MACsec/MKA:
	  - new macsec_linux driver interface support for the Linux
	    kernel macsec module
	  - number of fixes and extensions
	* added support for external persistent storage of PMKSA cache
	  (PMKSA_GET/PMKSA_ADD control interface commands; and
	   MESH_PMKSA_GET/MESH_PMKSA_SET for the mesh case)
	* fixed mesh channel configuration pri/sec switch case
	* added support for beacon report
	* large number of other fixes, cleanup, and extensions
	* added support for randomizing local address for GAS queries
	  (gas_rand_mac_addr parameter)
	* fixed EAP-SIM/AKA/AKA' ext auth cases within TLS tunnel
	* added option for using random WPS UUID (auto_uuid=1)
	* added SHA256-hash support for OCSP certificate matching
	* fixed EAP-AKA' to add AT_KDF into Synchronization-Failure
	* fixed a regression in RSN pre-authentication candidate selection
	* added option to configure allowed group management cipher suites
	  (group_mgmt network profile parameter)
	* removed all PeerKey functionality
	* fixed nl80211 AP and mesh mode configuration regression with
	  Linux 4.15 and newer
	* added ap_isolate configuration option for AP mode
	* added support for nl80211 to offload 4-way handshake into the driver
	* added support for using wolfSSL cryptographic library
	* SAE
	  - added support for configuring SAE password separately of the
	    WPA2 PSK/passphrase
	  - fixed PTK and EAPOL-Key integrity and key-wrap algorithm selection
	    for SAE;
	    note: this is not backwards compatible, i.e., both the AP and
	    station side implementations will need to be update at the same
	    time to maintain interoperability
	  - added support for Password Identifier
	  - fixed FT-SAE PMKID matching
	* Hotspot 2.0
	  - added support for fetching of Operator Icon Metadata ANQP-element
	  - added support for Roaming Consortium Selection element
	  - added support for Terms and Conditions
	  - added support for OSEN connection in a shared RSN BSS
	  - added support for fetching Venue URL information
	* added support for using OpenSSL 1.1.1
	* FT
	  - disabled PMKSA caching with FT since it is not fully functional
	  - added support for SHA384 based AKM
	  - added support for BIP ciphers BIP-CMAC-256, BIP-GMAC-128,
	    BIP-GMAC-256 in addition to previously supported BIP-CMAC-128
	  - fixed additional IE inclusion in Reassociation Request frame when
	    using FT protocol

2016-10-02 - v2.6
	* fixed WNM Sleep Mode processing when PMF is not enabled
	  [http://w1.fi/security/2015-6/] (CVE-2015-5310)
	* fixed EAP-pwd last fragment validation
	  [http://w1.fi/security/2015-7/] (CVE-2015-5315)
	* fixed EAP-pwd unexpected Confirm message processing
	  [http://w1.fi/security/2015-8/] (CVE-2015-5316)
	* fixed WPS configuration update vulnerability with malformed passphrase
	  [http://w1.fi/security/2016-1/] (CVE-2016-4476)
	* fixed configuration update vulnerability with malformed parameters set
	  over the local control interface
	  [http://w1.fi/security/2016-1/] (CVE-2016-4477)
	* fixed TK configuration to the driver in EAPOL-Key 3/4 retry case
	* extended channel switch support for P2P GO
	* started to throttle control interface event message bursts to avoid
	  issues with monitor sockets running out of buffer space
	* mesh mode fixes/improvements
	  - generate proper AID for peer
	  - enable WMM by default
	  - add VHT support
	  - fix PMKID derivation
	  - improve robustness on various exchanges
	  - fix peer link counting in reconnect case
	  - improve mesh joining behavior
	  - allow DTIM period to be configured
	  - allow HT to be disabled (disable_ht=1)
	  - add MESH_PEER_ADD and MESH_PEER_REMOVE commands
	  - add support for PMKSA caching
	  - add minimal support for SAE group negotiation
	  - allow pairwise/group cipher to be configured in the network profile
	  - use ieee80211w profile parameter to enable/disable PMF and derive
	    a separate TX IGTK if PMF is enabled instead of using MGTK
	    incorrectly
	  - fix AEK and MTK derivation
	  - remove GTKdata and IGTKdata from Mesh Peering Confirm/Close
	  - note: these changes are not fully backwards compatible for secure
	    (RSN) mesh network
	* fixed PMKID derivation with SAE
	* added support for requesting and fetching arbitrary ANQP-elements
	  without internal support in wpa_supplicant for the specific element
	  (anqp[265]=<hexdump> in "BSS <BSSID>" command output)
	* P2P
	  - filter control characters in group client device names to be
	    consistent with other P2P peer cases
	  - support VHT 80+80 MHz and 160 MHz
	  - indicate group completion in P2P Client role after data association
	    instead of already after the WPS provisioning step
	  - improve group-join operation to use SSID, if known, to filter BSS
	    entries
	  - added optional ssid=<hexdump> argument to P2P_CONNECT for join case
	  - added P2P_GROUP_MEMBER command to fetch client interface address
	* P2PS
	  - fix follow-on PD Response behavior
	  - fix PD Response generation for unknown peer
	  - fix persistent group reporting
	  - add channel policy to PD Request
	  - add group SSID to the P2PS-PROV-DONE event
	  - allow "P2P_CONNECT <addr> p2ps" to be used without specifying the
	    default PIN
	* BoringSSL
	  - support for OCSP stapling
	  - support building of h20-osu-client
	* D-Bus
	  - add ExpectDisconnect()
	  - add global config parameters as properties
	  - add SaveConfig()
	  - add VendorElemAdd(), VendorElemGet(), VendorElemRem()
	* fixed Suite B 192-bit AKM to use proper PMK length
	  (note: this makes old releases incompatible with the fixed behavior)
	* improved PMF behavior for cases where the AP and STA has different
	  configuration by not trying to connect in some corner cases where the
	  connection cannot succeed
	* added option to reopen debug log (e.g., to rotate the file) upon
	  receipt of SIGHUP signal
	* EAP-pwd: added support for Brainpool Elliptic Curves
	  (with OpenSSL 1.0.2 and newer)
	* fixed EAPOL reauthentication after FT protocol run
	* fixed FTIE generation for 4-way handshake after FT protocol run
	* extended INTERFACE_ADD command to allow certain type (sta/ap)
	  interface to be created
	* fixed and improved various FST operations
	* added 80+80 MHz and 160 MHz VHT support for IBSS/mesh
	* fixed SIGNAL_POLL in IBSS and mesh cases
	* added an option to abort an ongoing scan (used to speed up connection
	  and can also be done with the new ABORT_SCAN command)
	* TLS client
	  - do not verify CA certificates when ca_cert is not specified
	  - support validating server certificate hash
	  - support SHA384 and SHA512 hashes
	  - add signature_algorithms extension into ClientHello
	  - support TLS v1.2 signature algorithm with SHA384 and SHA512
	  - support server certificate probing
	  - allow specific TLS versions to be disabled with phase2 parameter
	  - support extKeyUsage
	  - support PKCS #5 v2.0 PBES2
	  - support PKCS #5 with PKCS #12 style key decryption
	  - minimal support for PKCS #12
	  - support OCSP stapling (including ocsp_multi)
	* OpenSSL
	  - support OpenSSL 1.1 API changes
	  - drop support for OpenSSL 0.9.8
	  - drop support for OpenSSL 1.0.0
	* added support for multiple schedule scan plans (sched_scan_plans)
	* added support for external server certificate chain validation
	  (tls_ext_cert_check=1 in the network profile phase1 parameter)
	* made phase2 parser more strict about correct use of auth=<val> and
	  autheap=<val> values
	* improved GAS offchannel operations with comeback request
	* added SIGNAL_MONITOR command to request signal strength monitoring
	  events
	* added command for retrieving HS 2.0 icons with in-memory storage
	  (REQ_HS20_ICON, GET_HS20_ICON, DEL_HS20_ICON commands and
	  RX-HS20-ICON event)
	* enabled ACS support for AP mode operations with wpa_supplicant
	* EAP-PEAP: fixed interoperability issue with Windows 2012r2 server
	  ("Invalid Compound_MAC in cryptobinding TLV")
	* EAP-TTLS: fixed success after fragmented final Phase 2 message
	* VHT: added interoperability workaround for 80+80 and 160 MHz channels
	* WNM: workaround for broken AP operating class behavior
	* added kqueue(2) support for eloop (CONFIG_ELOOP_KQUEUE)
	* nl80211:
	  - add support for full station state operations
	  - do not add NL80211_ATTR_SMPS_MODE attribute if HT is disabled
	  - add NL80211_ATTR_PREV_BSSID with Connect command
	  - fix IEEE 802.1X/WEP EAP reauthentication and rekeying to use
	    unencrypted EAPOL frames
	* added initial MBO support; number of extensions to WNM BSS Transition
	  Management
	* added support for PBSS/PCP and P2P on 60 GHz
	* Interworking: add credential realm to EAP-TLS identity
	* fixed EAPOL-Key Request Secure bit to be 1 if PTK is set
	* HS 2.0: add support for configuring frame filters
	* added POLL_STA command to check connectivity in AP mode
	* added initial functionality for location related operations
	* started to ignore pmf=1/2 parameter for non-RSN networks
	* added wps_disabled=1 network profile parameter to allow AP mode to
	  be started without enabling WPS
	* wpa_cli: added action script support for AP-ENABLED and AP-DISABLED
	  events
	* improved Public Action frame addressing
	  - add gas_address3 configuration parameter to control Address 3
	    behavior
	* number of small fixes

2015-09-27 - v2.5
	* fixed P2P validation of SSID element length before copying it
	  [http://w1.fi/security/2015-1/] (CVE-2015-1863)
	* fixed WPS UPnP vulnerability with HTTP chunked transfer encoding
	  [http://w1.fi/security/2015-2/] (CVE-2015-4141)
	* fixed WMM Action frame parser (AP mode)
	  [http://w1.fi/security/2015-3/] (CVE-2015-4142)
	* fixed EAP-pwd peer missing payload length validation
	  [http://w1.fi/security/2015-4/]
	  (CVE-2015-4143, CVE-2015-4144, CVE-2015-4145, CVE-2015-4146)
	* fixed validation of WPS and P2P NFC NDEF record payload length
	  [http://w1.fi/security/2015-5/]
	* nl80211:
	  - added VHT configuration for IBSS
	  - fixed vendor command handling to check OUI properly
	  - allow driver-based roaming to change ESS
	* added AVG_BEACON_RSSI to SIGNAL_POLL output
	* wpa_cli: added tab completion for number of commands
	* removed unmaintained and not yet completed SChannel/CryptoAPI support
	* modified Extended Capabilities element use in Probe Request frames to
	  include all cases if any of the values are non-zero
	* added support for dynamically creating/removing a virtual interface
	  with interface_add/interface_remove
	* added support for hashed password (NtHash) in EAP-pwd peer
	* added support for memory-only PSK/passphrase (mem_only_psk=1 and
	  CTRL-REQ/RSP-PSK_PASSPHRASE)
	* P2P
	  - optimize scan frequencies list when re-joining a persistent group
	  - fixed number of sequences with nl80211 P2P Device interface
	  - added operating class 125 for P2P use cases (this allows 5 GHz
	    channels 161 and 169 to be used if they are enabled in the current
	    regulatory domain)
	  - number of fixes to P2PS functionality
	  - do not allow 40 MHz co-ex PRI/SEC switch to force MCC
	  - extended support for preferred channel listing
	* D-Bus:
	  - fixed WPS property of fi.w1.wpa_supplicant1.BSS interface
	  - fixed PresenceRequest to use group interface
	  - added new signals: FindStopped, WPS pbc-overlap,
	    GroupFormationFailure, WPS timeout, InvitationReceived
	  - added new methods: WPS Cancel, P2P Cancel, Reconnect, RemoveClient
	  - added manufacturer info
	* added EAP-EKE peer support for deriving Session-Id
	* added wps_priority configuration parameter to set the default priority
	  for all network profiles added by WPS
	* added support to request a scan with specific SSIDs with the SCAN
	  command (optional "ssid <hexdump>" arguments)
	* removed support for WEP40/WEP104 as a group cipher with WPA/WPA2
	* fixed SAE group selection in an error case
	* modified SAE routines to be more robust and PWE generation to be
	  stronger against timing attacks
	* added support for Brainpool Elliptic Curves with SAE
	* added support for CCMP-256 and GCMP-256 as group ciphers with FT
	* fixed BSS selection based on estimated throughput
	* added option to disable TLSv1.0 with OpenSSL
	  (phase1="tls_disable_tlsv1_0=1")
	* added Fast Session Transfer (FST) module
	* fixed OpenSSL PKCS#12 extra certificate handling
	* fixed key derivation for Suite B 192-bit AKM (this breaks
	  compatibility with the earlier version)
	* added RSN IE to Mesh Peering Open/Confirm frames
	* number of small fixes

2015-03-15 - v2.4
	* allow OpenSSL cipher configuration to be set for internal EAP server
	  (openssl_ciphers parameter)
	* fixed number of small issues based on hwsim test case failures and
	  static analyzer reports
	* P2P:
	  - add new=<0/1> flag to P2P-DEVICE-FOUND events
	  - add passive channels in invitation response from P2P Client
	  - enable nl80211 P2P_DEVICE support by default
	  - fix regresssion in disallow_freq preventing search on social
	    channels
	  - fix regressions in P2P SD query processing
	  - try to re-invite with social operating channel if no common channels
	    in invitation
	  - allow cross connection on parent interface (this fixes number of
	    use cases with nl80211)
	  - add support for P2P services (P2PS)
	  - add p2p_go_ctwindow configuration parameter to allow GO CTWindow to
	    be configured
	* increase postponing of EAPOL-Start by one second with AP/GO that
	  supports WPS 2.0 (this makes it less likely to trigger extra roundtrip
	  of identity frames)
	* add support for PMKSA caching with SAE
	* add support for control mesh BSS (IEEE 802.11s) operations
	* fixed number of issues with D-Bus P2P commands
	* fixed regression in ap_scan=2 special case for WPS
	* fixed macsec_validate configuration
	* add a workaround for incorrectly behaving APs that try to use
	  EAPOL-Key descriptor version 3 when the station supports PMF even if
	  PMF is not enabled on the AP
	* allow TLS v1.1 and v1.2 to be negotiated by default; previous behavior
	  of disabling these can be configured to work around issues with broken
	  servers with phase1="tls_disable_tlsv1_1=1 tls_disable_tlsv1_2=1"
	* add support for Suite B (128-bit and 192-bit level) key management and
	  cipher suites
	* add WMM-AC support (WMM_AC_ADDTS/WMM_AC_DELTS)
	* improved BSS Transition Management processing
	* add support for neighbor report
	* add support for link measurement
	* fixed expiration of BSS entry with all-zeros BSSID
	* add optional LAST_ID=x argument to LIST_NETWORK to allow all
	  configured networks to be listed even with huge number of network
	  profiles
	* add support for EAP Re-Authentication Protocol (ERP)
	* fixed EAP-IKEv2 fragmentation reassembly
	* improved PKCS#11 configuration for OpenSSL
	* set stdout to be line-buffered
	* add TDLS channel switch configuration
	* add support for MAC address randomization in scans with nl80211
	* enable HT for IBSS if supported by the driver
	* add BSSID black and white lists (bssid_blacklist, bssid_whitelist)
	* add support for domain_suffix_match with GnuTLS
	* add OCSP stapling client support with GnuTLS
	* include peer certificate in EAP events even without a separate probe
	  operation; old behavior can be restored with cert_in_cb=0
	* add peer ceritficate alt subject name to EAP events
	  (CTRL-EVENT-EAP-PEER-ALT)
	* add domain_match network profile parameter (similar to
	  domain_suffix_match, but full match is required)
	* enable AP/GO mode HT Tx STBC automatically based on driver support
	* add ANQP-QUERY-DONE event to provide information on ANQP parsing
	  status
	* allow passive scanning to be forced with passive_scan=1
	* add a workaround for Linux packet socket behavior when interface is in
	  bridge
	* increase 5 GHz band preference in BSS selection (estimate SNR, if info
	  not available from driver; estimate maximum throughput based on common
	  HT/VHT/specific TX rate support)
	* add INTERWORKING_ADD_NETWORK ctrl_iface command; this can be used to
	  implement Interworking network selection behavior in upper layers
	  software components
	* add optional reassoc_same_bss_optim=1 (disabled by default)
	  optimization to avoid unnecessary Authentication frame exchange
	* extend TDLS frame padding workaround to cover all packets
	* allow wpa_supplicant to recover nl80211 functionality if the cfg80211
	  module gets removed and reloaded without restarting wpa_supplicant
	* allow hostapd DFS implementation to be used in wpa_supplicant AP mode

2014-10-09 - v2.3
	* fixed number of minor issues identified in static analyzer warnings
	* fixed wfd_dev_info to be more careful and not read beyond the buffer
	  when parsing invalid information for P2P-DEVICE-FOUND
	* extended P2P and GAS query operations to support drivers that have
	  maximum remain-on-channel time below 1000 ms (500 ms is the current
	  minimum supported value)
	* added p2p_search_delay parameter to make the default p2p_find delay
	  configurable
	* improved P2P operating channel selection for various multi-channel
	  concurrency cases
	* fixed some TDLS failure cases to clean up driver state
	* fixed dynamic interface addition cases with nl80211 to avoid adding
	  ifindex values to incorrect interface to skip foreign interface events
	  properly
	* added TDLS workaround for some APs that may add extra data to the
	  end of a short frame
	* fixed EAP-AKA' message parser with multiple AT_KDF attributes
	* added configuration option (p2p_passphrase_len) to allow longer
	  passphrases to be generated for P2P groups
	* fixed IBSS channel configuration in some corner cases
	* improved HT/VHT/QoS parameter setup for TDLS
	* modified D-Bus interface for P2P peers/groups
	* started to use constant time comparison for various password and hash
	  values to reduce possibility of any externally measurable timing
	  differences
	* extended explicit clearing of freed memory and expired keys to avoid
	  keeping private data in memory longer than necessary
	* added optional scan_id parameter to the SCAN command to allow manual
	  scan requests for active scans for specific configured SSIDs
	* fixed CTRL-EVENT-REGDOM-CHANGE event init parameter value
	* added option to set Hotspot 2.0 Rel 2 update_identifier in network
	  configuration to support external configuration
	* modified Android PNO functionality to send Probe Request frames only
	  for hidden SSIDs (based on scan_ssid=1)
	* added generic mechanism for adding vendor elements into frames at
	  runtime (VENDOR_ELEM_ADD, VENDOR_ELEM_GET, VENDOR_ELEM_REMOVE)
	* added fields to show unrecognized vendor elements in P2P_PEER
	* removed EAP-TTLS/MSCHAPv2 interoperability workaround so that
	  MS-CHAP2-Success is required to be present regardless of
	  eap_workaround configuration
	* modified EAP fast session resumption to allow results to be used only
	  with the same network block that generated them
	* extended freq_list configuration to apply for sched_scan as well as
	  normal scan
	* modified WPS to merge mixed-WPA/WPA2 credentials from a single session
	* fixed nl80211/RTM_DELLINK processing when a P2P GO interface is
	  removed from a bridge
	* fixed number of small P2P issues to make negotiations more robust in
	  corner cases
	* added experimental support for using temporary, random local MAC
	  address (mac_addr and preassoc_mac_addr parameters); this is disabled
	  by default (i.e., previous behavior of using permanent address is
	  maintained if configuration is not changed)
	* added D-Bus interface for setting/clearing WFD IEs
	* fixed TDLS AID configuration for VHT
	* modified -m<conf> configuration file to be used only for the P2P
	  non-netdev management device and do not load this for the default
	  station interface or load the station interface configuration for
	  the P2P management interface
	* fixed external MAC address changes while wpa_supplicant is running
	* started to enable HT (if supported by the driver) for IBSS
	* fixed wpa_cli action script execution to use more robust mechanism
	  (CVE-2014-3686)

2014-06-04 - v2.2
	* added DFS indicator to get_capability freq
	* added/fixed nl80211 functionality
	  - BSSID/frequency hint for driver-based BSS selection
	  - fix tearing down WDS STA interfaces
	  - support vendor specific driver command
	    (VENDOR <vendor id> <sub command id> [<hex formatted data>])
	  - GO interface teardown optimization
	  - allow beacon interval to be configured for IBSS
	  - add SHA256-based AKM suites to CONNECT/ASSOCIATE commands
	* removed unused NFC_RX_HANDOVER_REQ and NFC_RX_HANDOVER_SEL control
	  interface commands (the more generic NFC_REPORT_HANDOVER is now used)
	* fixed MSCHAP UTF-8 to UCS-2 conversion for three-byte encoding;
	  this fixes password with include UTF-8 characters that use
	  three-byte encoding EAP methods that use NtPasswordHash
	* fixed couple of sequencies where radio work items could get stuck,
	  e.g., when rfkill blocking happens during scanning or when
	  scan-for-auth workaround is used
	* P2P enhancements/fixes
	  - enable enable U-APSD on GO automatically if the driver indicates
	    support for this
	  - fixed some service discovery cases with broadcast queries not being
	    sent to all stations
	  - fixed Probe Request frame triggering invitation to trigger only a
	    single invitation instance even if multiple Probe Request frames are
	    received
	  - fixed a potential NULL pointer dereference crash when processing an
	    invalid Invitation Request frame
	  - add optional configuration file for the P2P_DEVICE parameters
	  - optimize scan for GO during persistent group invocation
	  - fix possible segmentation fault when PBC overlap is detected while
	    using a separate P2P group interface
	  - improve GO Negotiation robustness by allowing GO Negotiation
	    Confirmation to be retransmitted
	  - do use freed memory on device found event when P2P NFC
	* added phase1 network parameter options for disabling TLS v1.1 and v1.2
	  to allow workarounds with misbehaving AAA servers
	  (tls_disable_tlsv1_1=1 and tls_disable_tlsv1_2=1)
	* added support for OCSP stapling to validate AAA server certificate
	  during TLS exchange
	* Interworking/Hotspot 2.0 enhancements
	  - prefer the last added network in Interworking connection to make the
	    behavior more consistent with likely user expectation
	  - roaming partner configuration (roaming_partner within a cred block)
	  - support Hotspot 2.0 Release 2
	    * "hs20_anqp_get <BSSID> 8" to request OSU Providers list
	    * "hs20_icon_request <BSSID> <icon filename>" to request icon files
	    * "fetch_osu" and "cancel_osu_fetch" to start/stop full OSU provider
	      search (all suitable APs in scan results)
	    * OSEN network for online signup connection
	    * min_{dl,ul}_bandwidth_{home,roaming} cred parameters
	    * max_bss_load cred parameter
	    * req_conn_capab cred parameter
	    * sp_priority cred parameter
	    * ocsp cred parameter
	    * slow down automatic connection attempts on EAP failure to meet
	      required behavior (no more than 10 retries within a 10-minute
	      interval)
	    * sample implementation of online signup client (both SPP and
	      OMA-DM protocols) (hs20/client/*)
	  - fixed GAS indication for additional comeback delay with status
	    code 95
	  - extend ANQP_GET to accept Hotspot 2.0 subtypes
	    ANQP_GET <addr> <info id>[,<info id>]...
	    [,hs20:<subtype>][...,hs20:<subtype>]
	  - add control interface events CRED-ADDED <id>,
	    CRED-MODIFIED <id> <field>, CRED-REMOVED <id>
	  - add "GET_CRED <id> <field>" command
	  - enable FT for the connection automatically if the AP advertises
	    support for this
	  - fix a case where auto_interworking=1 could end up stopping scanning
	* fixed TDLS interoperability issues with supported operating class in
	  some deployed stations
	* internal TLS implementation enhancements/fixes
	  - add SHA256-based cipher suites
	  - add DHE-RSA cipher suites
	  - fix X.509 validation of PKCS#1 signature to check for extra data
	* fixed PTK derivation for CCMP-256 and GCMP-256
	* added "reattach" command for fast reassociate-back-to-same-BSS
	* allow PMF to be enabled for AP mode operation with the ieee80211w
	  parameter
	* added "get_capability tdls" command
	* added option to set config blobs through control interface with
	  "SET blob <name> <hexdump>"
	* D-Bus interface extensions/fixes
	  - make p2p_no_group_iface configurable
	  - declare ServiceDiscoveryRequest method properly
	  - export peer's device address as a property
	  - make reassociate command behave like the control interface one,
	    i.e., to allow connection from disconnected state
	* added optional "freq=<channel ranges>" parameter to SET pno
	* added optional "freq=<channel ranges>" parameter to SELECT_NETWORK
	* fixed OBSS scan result processing for 20/40 MHz co-ex report
	* remove WPS 1.0 only support, i.e., WSC 2.0 support is now enabled
	  whenever CONFIG_WPS=y is set
	* fixed regression in parsing of WNM Sleep Mode exit key data
	* fixed potential segmentation fault and memory leaks in WNM neighbor
	  report processing
	* EAP-pwd fixes
	  - fragmentation of PWD-Confirm-Resp
	  - fix memory leak when fragmentation is used
	  - fix possible segmentation fault on EAP method deinit if an invalid
	    group is negotiated
	* added MACsec/IEEE Std 802.1X-2010 PAE implementation (currently
	  available only with the macsec_qca driver wrapper)
	* fixed EAP-SIM counter-too-small message
	* added 'dup_network <id_s> <id_d> <name>' command; this can be used to
	  clone the psk field without having toextract it from wpa_supplicant
	* fixed GSM authentication on USIM
	* added support for usin epoll in eloop (CONFIG_ELOOP_EPOLL=y)
	* fixed some concurrent virtual interface cases with dedicated P2P
	  management interface to not catch events from removed interface (this
	  could result in the management interface getting disabled)
	* fixed a memory leak in SAE random number generation
	* fixed off-by-one bounds checking in printf_encode()
	  - this could result in some control interface ATTACH command cases
	    terminating wpa_supplicant
	* fixed EAPOL-Key exchange when GCMP is used with SHA256-based AKM
	* various bug fixes

2014-02-04 - v2.1
	* added support for simultaneous authentication of equals (SAE) for
	  stronger password-based authentication with WPA2-Personal
	* improved P2P negotiation and group formation robustness
	  - avoid unnecessary Dialog Token value changes during retries
	  - avoid more concurrent scanning cases during full group formation
	    sequence
	  - do not use potentially obsolete scan result data from driver
	    cache for peer discovery/updates
	  - avoid undesired re-starting of GO negotiation based on Probe
	    Request frames
	  - increase GO Negotiation and Invitation timeouts to address busy
	    environments and peers that take long time to react to messages,
	    e.g., due to power saving
	  - P2P Device interface type
	* improved P2P channel selection (use more peer information and allow
	  more local options)
	* added support for optional per-device PSK assignment by P2P GO
	  (wpa_cli p2p_set per_sta_psk <0/1>)
	* added P2P_REMOVE_CLIENT for removing a client from P2P groups
	  (including persistent groups); this can be used to securely remove
	  a client from a group if per-device PSKs are used
	* added more configuration flexibility for allowed P2P GO/client
	  channels (p2p_no_go_freq list and p2p_add_cli_chan=0/1)
	* added nl80211 functionality
	  - VHT configuration for nl80211
	  - MFP (IEEE 802.11w) information for nl80211 command API
	  - support split wiphy dump
	  - FT (IEEE 802.11r) with driver-based SME
	  - use advertised number of supported concurrent channels
	  - QoS Mapping configuration
	* improved TDLS negotiation robustness
	* added more TDLS peer parameters to be configured to the driver
	* optimized connection time by allowing recently received scan results
	  to be used instead of having to run through a new scan
	* fixed ctrl_iface BSS command iteration with RANGE argument and no
	  exact matches; also fixed argument parsing for some cases with
	  multiple arguments
	* added 'SCAN TYPE=ONLY' ctrl_iface command to request manual scan
	  without executing roaming/network re-selection on scan results
	* added Session-Id derivation for EAP peer methods
	* added fully automated regression testing with mac80211_hwsim
	* changed configuration parser to reject invalid integer values
	* allow AP/Enrollee to be specified with BSSID instead of UUID for
	  WPS ER operations
	* disable network block temporarily on repeated connection failures
	* changed the default driver interface from wext to nl80211 if both are
	  included in the build
	* remove duplicate networks if WPS provisioning is run multiple times
	* remove duplicate networks when Interworking network selection uses the
	  same network
	* added global freq_list configuration to allow scan frequencies to be
	  limited for all cases instead of just for a specific network block
	* added support for BSS Transition Management
	* added option to use "IFNAME=<ifname> " prefix to use the global
	  control interface connection to perform per-interface commands;
	  similarly, allow global control interface to be used as a monitor
	  interface to receive events from all interfaces
	* fixed OKC-based PMKSA cache entry clearing
	* fixed TKIP group key configuration with FT
	* added support for using OCSP stapling to validate server certificate
	  (ocsp=1 as optional and ocsp=2 as mandatory)
	* added EAP-EKE peer
	* added peer restart detection for IBSS RSN
	* added domain_suffix_match (and domain_suffix_match2 for Phase 2
	  EAP-TLS) to specify additional constraint for the server certificate
	  domain name
	* added support for external SIM/USIM processing in EAP-SIM, EAP-AKA,
	  and EAP-AKA' (CTRL-REQ-SIM and CTRL-RSP-SIM commands over control
	  interface)
	* added global bgscan configuration option as a default for all network
	  blocks that do not specify their own bgscan parameters
	* added D-Bus methods for TDLS
	* added more control to scan requests
	  - "SCAN freq=<freq list>" can be used to specify which channels are
	    scanned (comma-separated frequency ranges in MHz)
	  - "SCAN passive=1" can be used to request a passive scan (no Probe
	    Request frames are sent)
	  - "SCAN use_id" can be used to request a scan id to be returned and
	    included in event messages related to this specific scan operation
	  - "SCAN only_new=1" can be used to request the driver/cfg80211 to
	    report only BSS entries that have been updated during this scan
	    round
	  - these optional arguments to the SCAN command can be combined with
	    each other
	* modified behavior on externally triggered scans
	  - avoid concurrent operations requiring full control of the radio when
	    an externally triggered scan is detected
	  - do not use results for internal roaming decision
	* added a new cred block parameter 'temporary' to allow credential
	  blocks to be stored separately even if wpa_supplicant configuration
	  file is used to maintain other network information
	* added "radio work" framework to schedule exclusive radio operations
	  for off-channel functionality
	  - reduce issues with concurrent operations that try to control which
	    channel is used
	  - allow external programs to request exclusive radio control in a way
	    that avoids conflicts with wpa_supplicant
	* added support for using Protected Dual of Public Action frames for
	  GAS/ANQP exchanges when associated with PMF
	* added support for WPS+NFC updates and P2P+NFC
	  - improved protocol for WPS
	  - P2P group formation/join based on NFC connection handover
	  - new IPv4 address assignment for P2P groups (ip_addr_* configuration
	    parameters on the GO) to replace DHCP
	  - option to fetch and report alternative carrier records for external
	    NFC operations
	* various bug fixes

2013-01-12 - v2.0
	* removed Qt3-based wpa_gui (obsoleted by wpa_qui-qt4)
	* removed unmaintained driver wrappers broadcom, iphone, osx, ralink,
	  hostap, madwifi (hostap and madwifi remain available for hostapd;
	  their wpa_supplicant functionality is obsoleted by wext)
	* improved debug logging (human readable event names, interface name
	  included in more entries)
	* changed AP mode behavior to enable WPS only for open and
	  WPA/WPA2-Personal configuration
	* improved P2P concurrency operations
	  - better coordination of concurrent scan and P2P search operations
	  - avoid concurrent remain-on-channel operation requests by canceling
	    previous operations prior to starting a new one
	  - reject operations that would require multi-channel concurrency if
	    the driver does not support it
	  - add parameter to select whether STA or P2P connection is preferred
	    if the driver cannot support both at the same time
	  - allow driver to indicate channel changes
	  - added optional delay=<search delay in milliseconds> parameter for
	    p2p_find to avoid taking all radio resources
	  - use 500 ms p2p_find search delay by default during concurrent
	    operations
	  - allow all channels in GO Negotiation if the driver supports
	    multi-channel concurrency
	* added number of small changes to make it easier for static analyzers
	  to understand the implementation
	* fixed number of small bugs (see git logs for more details)
	* nl80211: number of updates to use new cfg80211/nl80211 functionality
	  - replace monitor interface with nl80211 commands for AP mode
	  - additional information for driver-based AP SME
	  - STA entry authorization in RSN IBSS
	* EAP-pwd:
	  - fixed KDF for group 21 and zero-padding
	  - added support for fragmentation
	  - increased maximum number of hunting-and-pecking iterations
	* avoid excessive Probe Response retries for broadcast Probe Request
	  frames (only with drivers using wpa_supplicant AP mode SME/MLME)
	* added "GET country" ctrl_iface command
	* do not save an invalid network block in wpa_supplicant.conf to avoid
	  problems reading the file on next start
	* send STA connected/disconnected ctrl_iface events to both the P2P
	  group and parent interfaces
	* added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y)
	* added "SET pno <1/0>" ctrl_iface command to start/stop preferred
	  network offload with sched_scan driver command
	* merged in number of changes from Android repository for P2P, nl80211,
	  and build parameters
	* changed P2P GO mode configuration to use driver capabilities to
	  automatically enable HT operations when supported
	* added "wpa_cli status wps" command to fetch WPA2-Personal passhrase
	  for WPS use cases in AP mode
	* EAP-AKA: keep pseudonym identity across EAP exchanges to match EAP-SIM
	  behavior
	* improved reassociation behavior in cases where association is rejected
	  or when an AP disconnects us to handle common load balancing
	  mechanisms
	  - try to avoid extra scans when the needed information is available
	* added optional "join" argument for p2p_prov_disc ctrl_iface command
	* added group ifname to P2P-PROV-DISC-* events
	* added P2P Device Address to AP-STA-DISCONNECTED event and use
	  p2p_dev_addr parameter name with AP-STA-CONNECTED
	* added workarounds for WPS PBC overlap detection for some P2P use cases
	  where deployed stations work incorrectly
	* optimize WPS connection speed by disconnecting prior to WPS scan and
	  by using single channel scans when AP channel is known
	* PCSC and SIM/USIM improvements:
	  - accept 0x67 (Wrong length) as a response to READ RECORD to fix
	    issues with some USIM cards
	  - try to read MNC length from SIM/USIM
	  - build realm according to 3GPP TS 23.003 with identity from the SIM
	  - allow T1 protocol to be enabled
	* added more WPS and P2P information available through D-Bus
	* improve P2P negotiation robustness
	  - extra waits to get ACK frames through
	  - longer timeouts for cases where deployed devices have been
	    identified have issues meeting the specification requirements
	  - more retries for some P2P frames
	  - handle race conditions in GO Negotiation start by both devices
	  - ignore unexpected GO Negotiation Response frame
	* added support for libnl 3.2 and newer
	* added P2P persistent group info to P2P_PEER data
	* maintain a list of P2P Clients for persistent group on GO
	* AP: increased initial group key handshake retransmit timeout to 500 ms
	* added optional dev_id parameter for p2p_find
	* added P2P-FIND-STOPPED ctrl_iface event
	* fixed issues in WPA/RSN element validation when roaming with ap_scan=1
	  and driver-based BSS selection
	* do not expire P2P peer entries while connected with the peer in a
	  group
	* fixed WSC element inclusion in cases where P2P is disabled
	* AP: added a WPS workaround for mixed mode AP Settings with Windows 7
	* EAP-SIM: fixed AT_COUNTER_TOO_SMALL use
	* EAP-SIM/AKA: append realm to pseudonym identity
	* EAP-SIM/AKA: store pseudonym identity in network configuration to
	  allow it to persist over multiple EAP sessions and wpa_supplicant
	  restarts
	* EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this
	  breaks interoperability with older versions
	* added support for WFA Hotspot 2.0
	  - GAS/ANQP to fetch network information
	  - credential configuration and automatic network selections based on
	    credential match with ANQP information
	* limited PMKSA cache entries to be used only with the network context
	  that was used to create them
	* improved PMKSA cache expiration to avoid unnecessary disconnections
	* adjusted bgscan_simple fast-scan backoff to avoid too frequent
	  background scans
	* removed ctrl_iface event on P2P PD Response in join-group case
	* added option to fetch BSS table entry based on P2P Device Address
	  ("BSS p2p_dev_addr=<P2P Device Address>")
	* added BSS entry age to ctrl_iface BSS command output
	* added optional MASK=0xH option for ctrl_iface BSS command to select
	  which fields are included in the response
	* added optional RANGE=ALL|N1-N2 option for ctrl_iface BSS command to
	  fetch information about several BSSes in one call
	* simplified licensing terms by selecting the BSD license as the only
	  alternative
	* added "P2P_SET disallow_freq <freq list>" ctrl_iface command to
	  disable channels from P2P use
	* added p2p_pref_chan configuration parameter to allow preferred P2P
	  channels to be specified
	* added support for advertising immediate availability of a WPS
	  credential for P2P use cases
	* optimized scan operations for P2P use cases (use single channel scan
	  for a specific SSID when possible)
	* EAP-TTLS: fixed peer challenge generation for MSCHAPv2
	* SME: do not use reassociation after explicit disconnection request
	  (local or a notification from an AP)
	* added support for sending debug info to Linux tracing (-T on command
	  line)
	* added support for using Deauthentication reason code 3 as an
	  indication of P2P group termination
	* added wps_vendor_ext_m1 configuration parameter to allow vendor
	  specific attributes to be added to WPS M1
	* started using separate TLS library context for tunneled TLS
	  (EAP-PEAP/TLS, EAP-TTLS/TLS, EAP-FAST/TLS) to support different CA
	  certificate configuration between Phase 1 and Phase 2
	* added optional "auto" parameter for p2p_connect to request automatic
	  GO Negotiation vs. join-a-group selection
	* added disabled_scan_offload parameter to disable automatic scan
	  offloading (sched_scan)
	* added optional persistent=<network id> parameter for p2p_connect to
	  allow forcing of a specific SSID/passphrase for GO Negotiation
	* added support for OBSS scan requests and 20/40 BSS coexistence reports
	* reject PD Request for unknown group
	* removed scripts and notes related to Windows binary releases (which
	  have not been used starting from 1.x)
	* added initial support for WNM operations
	  - Keep-alive based on BSS max idle period
	  - WNM-Sleep Mode
	  - minimal BSS Transition Management processing
	* added autoscan module to control scanning behavior while not connected
	  - autoscan_periodic and autoscan_exponential modules
	* added new WPS NFC ctrl_iface mechanism
	  - added initial support NFC connection handover
	  - removed obsoleted WPS_OOB command (including support for deprecated
	    UFD config_method)
	* added optional framework for external password storage ("ext:<name>")
	* wpa_cli: added optional support for controlling wpa_supplicant
	  remotely over UDP (CONFIG_CTRL_IFACE=udp-remote) for testing purposes
	* wpa_cli: extended tab completion to more commands
	* changed SSID output to use printf-escaped strings instead of masking
	  of non-ASCII characters
	  - SSID can now be configured in the same format: ssid=P"abc\x00test"
	* removed default ACM=1 from AC_VO and AC_VI
	* added optional "ht40" argument for P2P ctrl_iface commands to allow
	  40 MHz channels to be requested on the 5 GHz band
	* added optional parameters for p2p_invite command to specify channel
	  when reinvoking a persistent group as the GO
	* improved FIPS mode builds with OpenSSL
	  - "make fips" with CONFIG_FIPS=y to build wpa_supplicant with the
	    OpenSSL FIPS object module
	  - replace low level OpenSSL AES API calls to use EVP
	  - use OpenSSL keying material exporter when possible
	  - do not export TLS keys in FIPS mode
	  - remove MD5 from CONFIG_FIPS=y builds
	  - use OpenSSL function for PKBDF2 passphrase-to-PSK
	  - use OpenSSL HMAC implementation
	  - mix RAND_bytes() output into random_get_bytes() to force OpenSSL
	    DRBG to be used in FIPS mode
	  - use OpenSSL CMAC implementation
	* added mechanism to disable TLS Session Ticket extension
	  - a workaround for servers that do not support TLS extensions that
	    was enabled by default in recent OpenSSL versions
	  - tls_disable_session_ticket=1
	  - automatically disable TLS Session Ticket extension by default when
	    using EAP-TLS/PEAP/TTLS (i.e., only use it with EAP-FAST)
	* changed VENDOR-TEST EAP method to use proper private enterprise number
	  (this will not interoperate with older versions)
	* disable network block temporarily on authentication failures
	* improved WPS AP selection during WPS PIN iteration
	* added support for configuring GCMP cipher for IEEE 802.11ad
	* added support for Wi-Fi Display extensions
	  - WFD_SUBELEMENT_SET ctrl_iface command to configure WFD subelements
	  - SET wifi_display <0/1> to disable/enable WFD support
	  - WFD service discovery
	  - an external program is needed to manage the audio/video streaming
	    and codecs
	* optimized scan result use for network selection
	  - use the internal BSS table instead of raw scan results
	  - allow unnecessary scans to be skipped if fresh information is
	    available (e.g., after GAS/ANQP round for Interworking)
	* added support for 256-bit AES with internal TLS implementation
	* allow peer to propose channel in P2P invitation process for a
	  persistent group
	* added disallow_aps parameter to allow BSSIDs/SSIDs to be disallowed
	  from network selection
	* re-enable the networks disabled during WPS operations
	* allow P2P functionality to be disabled per interface (p2p_disabled=1)
	* added secondary device types into P2P_PEER output
	* added an option to disable use of a separate P2P group interface
	  (p2p_no_group_iface=1)
	* fixed P2P Bonjour SD to match entries with both compressed and not
	  compressed domain name format and support multiple Bonjour PTR matches
	  for the same key
	* use deauthentication instead of disassociation for all disconnection
	  operations; this removes the now unused disassociate() wpa_driver_ops
	  callback
	* optimized PSK generation on P2P GO by caching results to avoid
	  multiple PBKDF2 operations
	* added okc=1 global configuration parameter to allow OKC to be enabled
	  by default for all network blocks
	* added a workaround for WPS PBC session overlap detection to avoid
	  interop issues with deployed station implementations that do not
	  remove active PBC indication from Probe Request frames properly
	* added basic support for 60 GHz band
	* extend EAPOL frames processing workaround for roaming cases
	  (postpone processing of unexpected EAPOL frame until association
	  event to handle reordered events)

2012-05-10 - v1.0
	* bsd: Add support for setting HT values in IFM_MMASK.
	* Delay STA entry removal until Deauth/Disassoc TX status in AP mode.
	  This allows the driver to use PS buffering of Deauthentication and
	  Disassociation frames when the STA is in power save sleep. Only
	  available with drivers that provide TX status events for Deauth/
	  Disassoc frames (nl80211).
	* Drop oldest unknown BSS table entries first. This makes it less
	  likely to hit connection issues in environments with huge number
	  of visible APs.
	* Add systemd support.
	* Add support for setting the syslog facility from the config file
	  at build time.
	* atheros: Add support for IEEE 802.11w configuration.
	* AP mode: Allow enable HT20 if driver supports it, by setting the
	  config parameter ieee80211n.
	* Allow AP mode to disconnect STAs based on low ACK condition (when
	  the data connection is not working properly, e.g., due to the STA
	  going outside the range of the AP). Disabled by default, enable by
	  config option disassoc_low_ack.
	* nl80211:
	  - Support GTK rekey offload.
	  - Support PMKSA candidate events. This adds support for RSN
	    pre-authentication with nl80211 interface and drivers that handle
	    roaming internally.
	* dbus:
	  - Add a DBus signal for EAP SM requests, emitted on the Interface
	    object.
	  - Export max scan ssids supported by the driver as MaxScanSSID.
	  - Add signal Certification for information about server certification.
	  - Add BSSExpireAge and BSSExpireCount interface properties and
	    support set/get, which allows for setting BSS cache expiration age
	    and expiration scan count.
	  - Add ConfigFile to AddInterface properties.
	  - Add Interface.Country property and support to get/set the value.
	  - Add DBus property CurrentAuthMode.
	  - P2P DBus API added.
	  - Emit property changed events (for property BSSs) when adding/
	    removing BSSs.
	  - Treat '' in SSIDs of Interface.Scan as a request for broadcast
	    scan, instead of ignoring it.
	  - Add DBus getter/setter for FastReauth.
	  - Raise PropertiesChanged on org.freedesktop.DBus.Properties.
	* wpa_cli:
	  - Send AP-STA-DISCONNECTED event when an AP disconnects a station
	    due to inactivity.
	  - Make second argument to set command optional. This can be used to
	    indicate a zero length value.
	  - Add signal_poll command.
	  - Add bss_expire_age and bss_expire_count commands to set/get BSS
	    cache expiration age and expiration scan count.
	  - Add ability to set scan interval (the time in seconds wpa_s waits
	    before requesting a new scan after failing to find a suitable
	    network in scan results) using scan_interval command.
	  - Add event CTRL-EVENT-ASSOC-REJECT for association rejected.
	  - Add command get version, that returns wpa_supplicant version string.
	  - Add command sta_autoconnect for disabling automatic reconnection
	    on receiving disconnection event.
	  - Setting bssid parameter to an empty string "" or any can now be
	    used to clear the bssid_set flag in a network block, i.e., to remove
	    bssid filtering.
	  - Add tdls_testing command to add a special testing feature for
	    changing TDLS behavior. Build param CONFIG_TDLS_TESTING must be
	    enabled as well.
	  - For interworking, add wpa_cli commands interworking_select,
	    interworking_connect, anqp_get, fetch_anqp, and stop_fetch_anqp.
	  - Many P2P commands were added. See README-P2P.
	  - Many WPS/WPS ER commands - see WPS/WPS ER sections for details.
	  - Allow set command to change global config parameters.
	  - Add log_level command, which can be used to display the current
	    debugging level and to change the log level during run time.
	  - Add note command, which can be used to insert notes to the debug
	    log.
	  - Add internal line edit implementation. CONFIG_WPA_CLI_EDIT=y
	    can now be used to build wpa_cli with internal implementation of
	    line editing and history support. This can be used as a replacement
	    for CONFIG_READLINE=y.
	* AP mode: Add max_num_sta config option, which can be used to limit
	  the number of stations allowed to connect to the AP.
	* Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad
	  config file.
	* wext: Increase scan timeout from 5 to 10 seconds.
	* Add blacklist command, allowing an external program to
	  manage the BSS blacklist and display its current contents.
	* WPS:
	  - Add wpa_cli wps_pin get command for generating random PINs. This can
	    be used in a UI to generate a PIN without starting WPS (or P2P)
	    operation.
	  - Set RF bands based on driver capabilities, instead of hardcoding
	    them.
	  - Add mechanism for indicating non-standard WPS errors.
	  - Add CONFIG_WPS_REG_DISABLE_OPEN=y option to disable open networks
	    by default.
	  - Add wps_ap_pin cli command for wpa_supplicant AP mode.
	  - Add wps_check_pin cli command for processing PIN from user input.
	    UIs can use this command to process a PIN entered by a user and to
	    validate the checksum digit (if present).
	  - Cancel WPS operation on PBC session overlap detection.
	  - New wps_cancel command in wpa_cli will cancel a pending WPS
	    operation.
	  - wpa_cli action: Add WPS_EVENT_SUCCESS and WPS_EVENT_FAIL handlers.
	  - Trigger WPS config update on Manufacturer, Model Name, Model
	    Number, and Serial Number changes.
	  - Fragment size is now configurable for EAP-WSC peer. Use
	    wpa_cli set wps_fragment_size <val>.
	  - Disable AP PIN after 10 consecutive failures. Slow down attacks on
	    failures up to 10.
	  - Allow AP to start in Enrollee mode without AP PIN for probing, to
	    be compatible with Windows 7.
	  - Add Config Error into WPS-FAIL events to provide more info to the
	    user on how to resolve the issue.
	  - Label and Display config methods are not allowed to be enabled
	    at the same time, since it is unclear which PIN to use if both
	    methods are advertised.
	  - When controlling multiple interfaces:
	     - apply WPS commands to all interfaces configured to use WPS
	     - apply WPS config changes to all interfaces that use WPS
	     - when an attack is detected on any interface, disable AP PIN on
	       all interfaces
	* WPS ER:
	  - Add special AP Setup Locked mode to allow read only ER.
	    ap_setup_locked=2 can now be used to enable a special mode where
	    WPS ER can learn the current AP settings, but cannot change them.
	  - Show SetSelectedRegistrar events as ctrl_iface events
	  - Add wps_er_set_config to enroll a network based on a local
	    network configuration block instead of having to (re-)learn the
	    current AP settings with wps_er_learn.
	  - Allow AP filtering based on IP address, add ctrl_iface event for
	    learned AP settings, add wps_er_config command to configure an AP.
	* WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2)
	  - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool
	    for testing protocol extensibility.
	  - Add build option CONFIG_WPS_STRICT to allow disabling of WPS
	    workarounds.
	  - Add support for AuthorizedMACs attribute.
	* TDLS:
	  - Propogate TDLS related nl80211 capability flags from kernel and
	    add them as driver capability flags. If the driver doesn't support
	    capabilities, assume TDLS is supported internally. When TDLS is
	    explicitly not supported, disable all user facing TDLS operations.
	  - Allow TDLS to be disabled at runtime (mostly for testing).
	    Use set tdls_disabled.
	  - Honor AP TDLS settings that prohibit/allow TDLS.
	  - Add a special testing feature for changing TDLS behavior. Use
	    CONFIG_TDLS_TESTING build param to enable. Configure at runtime
	    with tdls_testing cli command.
	  - Add support for TDLS 802.11z.
	* wlantest: Add a tool wlantest for IEEE802.11 protocol testing.
	  wlantest can be used to capture frames from a monitor interface
	  for realtime capturing or from pcap files for offline analysis.
	* Interworking: Support added for 802.11u. Enable in .config with
	  CONFIG_INTERWORKING. See wpa_supplicant.conf for config parameters
	  for interworking. wpa_cli commands added to support this are
	  interworking_select, interworking_connect, anqp_get, fetch_anqp,
	  and stop_fetch_anqp.
	* Android: Add build and runtime support for Android wpa_supplicant.
	* bgscan learn: Add new bgscan that learns BSS information based on
	  previous scans, and uses that information to dynamically generate
	  the list of channels for background scans.
	* Add a new debug message level for excessive information. Use
	  -ddd to enable.
	* TLS: Add support for tls_disable_time_checks=1 in client mode.
	* Internal TLS:
	  - Add support for TLS v1.1 (RFC 4346). Enable with build parameter
	    CONFIG_TLSV11.
	  - Add domainComponent parser for X.509 names.
	* Linux: Add RFKill support by adding an interface state "disabled".
	* Reorder some IEs to get closer to IEEE 802.11 standard. Move
	  WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames.
	  Move HT IEs to be later in (Re)Assoc Resp.
	* Solaris: Add support for wired 802.1X client.
	* Wi-Fi Direct support. See README-P2P for more information.
	* Many bugfixes.

2010-04-18 - v0.7.2
	* nl80211: fixed number of issues with roaming
	* avoid unnecessary roaming if multiple APs with similar signal
	  strength are present in scan results
	* add TLS client events and server probing to ease design of
	  automatic detection of EAP parameters
	* add option for server certificate matching (SHA256 hash of the
	  certificate) instead of trusted CA certificate configuration
	* bsd: Cleaned up driver wrapper and added various low-level
	  configuration options
	* wpa_gui-qt4: do not show too frequent WPS AP available events as
	  tray messages
	* TNC: fixed issues with fragmentation
	* EAP-TNC: add Flags field into fragment acknowledgement (needed to
	  interoperate with other implementations; may potentially breaks
	  compatibility with older wpa_supplicant/hostapd versions)
	* wpa_cli: added option for using a separate process to receive event
	  messages to reduce latency in showing these
	  (CFLAGS += -DCONFIG_WPA_CLI_FORK=y in .config to enable this)
	* maximum BSS table size can now be configured (bss_max_count)
	* BSSes to be included in the BSS table can be filtered based on
	  configured SSIDs to save memory (filter_ssids)
	* fix number of issues with IEEE 802.11r/FT; this version is not
	  backwards compatible with old versions
	* nl80211: add support for IEEE 802.11r/FT protocol (both over-the-air
	  and over-the-DS)
	* add freq_list network configuration parameter to allow the AP
	  selection to filter out entries based on the operating channel
	* add signal strength change events for bgscan; this allows more
	  dynamic changes to background scanning interval based on changes in
	  the signal strength with the current AP; this improves roaming within
	  ESS quite a bit, e.g., with bgscan="simple:30:-45:300" in the network
	  configuration block to request background scans less frequently when
	  signal strength remains good and to automatically trigger background
	  scans whenever signal strength drops noticeably
	  (this is currently only available with nl80211)
	* add BSSID and reason code (if available) to disconnect event messages
	* wpa_gui-qt4: more complete support for translating the GUI with
	  linguist and add German translation
	* fix DH padding with internal crypto code (mainly, for WPS)
	* do not trigger initial scan automatically anymore if there are no
	  enabled networks

2010-01-16 - v0.7.1
	* cleaned up driver wrapper API (struct wpa_driver_ops); the new API
	  is not fully backwards compatible, so out-of-tree driver wrappers
	  will need modifications
	* cleaned up various module interfaces
	* merge hostapd and wpa_supplicant developers' documentation into a
	  single document
	* nl80211: use explicit deauthentication to clear cfg80211 state to
	  avoid issues when roaming between APs
	* dbus: major design changes in the new D-Bus API
	  (fi.w1.wpa_supplicant1)
	* nl80211: added support for IBSS networks
	* added internal debugging mechanism with backtrace support and memory
	  allocation/freeing validation, etc. tests (CONFIG_WPA_TRACE=y)
	* added WPS ER unsubscription command to more cleanly unregister from
	  receiving UPnP events when ER is terminated
	* cleaned up AP mode operations to avoid need for virtual driver_ops
	  wrapper
	* added BSS table to maintain more complete scan result information
	  over multiple scans (that may include only partial results)
	* wpa_gui-qt4: update Peers dialog information more dynamically while
	  the dialog is kept open
	* fixed PKCS#12 use with OpenSSL 1.0.0
	* driver_wext: Added cfg80211-specific optimization to avoid some
	  unnecessary scans and to speed up association

2009-11-21 - v0.7.0
	* increased wpa_cli ping interval to 5 seconds and made this
	  configurable with a new command line options (-G<seconds>)
	* fixed scan buffer processing with WEXT to handle up to 65535
	  byte result buffer (previously, limited to 32768 bytes)
	* allow multiple driver wrappers to be specified on command line
	  (e.g., -Dnl80211,wext); the first one that is able to initialize the
	  interface will be used
	* added support for multiple SSIDs per scan request to optimize
	  scan_ssid=1 operations in ap_scan=1 mode (i.e., search for hidden
	  SSIDs); this requires driver support and can currently be used only
	  with nl80211
	* added support for WPS USBA out-of-band mechanism with USB Flash
	  Drives (UFD) (CONFIG_WPS_UFD=y)
	* driver_ndis: add PAE group address to the multicast address list to
	  fix wired IEEE 802.1X authentication
	* fixed IEEE 802.11r key derivation function to match with the standard
	  (note: this breaks interoperability with previous version) [Bug 303]
	* added better support for drivers that allow separate authentication
	  and association commands (e.g., mac80211-based Linux drivers with
	  nl80211; SME in wpa_supplicant); this allows over-the-air FT protocol
	  to be used (IEEE 802.11r)
	* fixed SHA-256 based key derivation function to match with the
	  standard when using CCMP (for IEEE 802.11r and IEEE 802.11w)
	  (note: this breaks interoperability with previous version) [Bug 307]
	* use shared driver wrapper files with hostapd
	* added AP mode functionality (CONFIG_AP=y) with mode=2 in the network
	  block; this can be used for open and WPA2-Personal networks
	  (optionally, with WPS); this links in parts of hostapd functionality
	  into wpa_supplicant
	* wpa_gui-qt4: added new Peers dialog to show information about peers
	  (other devices, including APs and stations, etc. in the neighborhood)
	* added support for WPS External Registrar functionality (configure APs
	  and enroll new devices); can be used with wpa_gui-qt4 Peers dialog
	  and wpa_cli commands wps_er_start, wps_er_stop, wps_er_pin,
	  wps_er_pbc, wps_er_learn
	  (this can also be used with a new 'none' driver wrapper if no
	  wireless device or IEEE 802.1X on wired is needed)
	* driver_nl80211: multiple updates to provide support for new Linux
	  nl80211/mac80211 functionality
	* updated management frame protection to use IEEE Std 802.11w-2009
	* fixed number of small WPS issues and added workarounds to
	  interoperate with common deployed broken implementations
	* added support for NFC out-of-band mechanism with WPS
	* driver_ndis: fixed wired IEEE 802.1X authentication with PAE group
	  address frames
	* added preliminary support for IEEE 802.11r RIC processing
	* added support for specifying subset of enabled frequencies to scan
	  (scan_freq option in the network configuration block); this can speed
	  up scanning process considerably if it is known that only a small
	  subset of channels is actually used in the network (this is currently
	  supported only with -Dnl80211)
	* added a workaround for race condition between receiving the
	  association event and the following EAPOL-Key
	* added background scan and roaming infrastructure to allow
	  network-specific optimizations to be used to improve roaming within
	  an ESS (same SSID)
	* added new DBus interface (fi.w1.wpa_supplicant1)

2009-01-06 - v0.6.7
	* added support for Wi-Fi Protected Setup (WPS)
	  (wpa_supplicant can now be configured to act as a WPS Enrollee to
	  enroll credentials for a network using PIN and PBC methods; in
	  addition, wpa_supplicant can act as a wireless WPS Registrar to
	  configure an AP); WPS support can be enabled by adding CONFIG_WPS=y
	  into .config and setting the runtime configuration variables in
	  wpa_supplicant.conf (see WPS section in the example configuration
	  file); new wpa_cli commands wps_pin, wps_pbc, and wps_reg are used to
	  manage WPS negotiation; see README-WPS for more details
	* added support for EAP-AKA' (draft-arkko-eap-aka-kdf)
	* added support for using driver_test over UDP socket
	* fixed PEAPv0 Cryptobinding interoperability issue with Windows Server
	  2008 NPS; optional cryptobinding is now enabled (again) by default
	* fixed PSK editing in wpa_gui
	* changed EAP-GPSK to use the IANA assigned EAP method type 51
	* added a Windows installer that includes WinPcap and all the needed
	  DLLs; in addition, it set up the registry automatically so that user
	  will only need start wpa_gui to get prompted to start the wpasvc
	  servide and add a new interface if needed through wpa_gui dialog
	* updated management frame protection to use IEEE 802.11w/D7.0

2008-11-23 - v0.6.6
	* added Milenage SIM/USIM emulator for EAP-SIM/EAP-AKA
	  (can be used to simulate test SIM/USIM card with a known private key;
	  enable with CONFIG_SIM_SIMULATOR=y/CONFIG_USIM_SIMULATOR=y in .config
	  and password="Ki:OPc"/password="Ki:OPc:SQN" in network configuration)
	* added a new network configuration option, wpa_ptk_rekey, that can be
	  used to enforce frequent PTK rekeying, e.g., to mitigate some attacks
	  against TKIP deficiencies
	* added an optional mitigation mechanism for certain attacks against
	  TKIP by delaying Michael MIC error reports by a random amount of time
	  between 0 and 60 seconds; this can be enabled with a build option
	  CONFIG_DELAYED_MIC_ERROR_REPORT=y in .config
	* fixed EAP-AKA to use RES Length field in AT_RES as length in bits,
	  not bytes
	* updated OpenSSL code for EAP-FAST to use an updated version of the
	  session ticket overriding API that was included into the upstream
	  OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is
	  needed with that version anymore)
	* updated userspace MLME instructions to match with the current Linux
	  mac80211 implementation; please also note that this can only be used
	  with driver_nl80211.c (the old code from driver_wext.c was removed)
	* added support (Linux only) for RoboSwitch chipsets (often found in
	  consumer grade routers); driver interface 'roboswitch'
	* fixed canceling of PMKSA caching when using drivers that generate
	  RSN IE and refuse to drop PMKIDs that wpa_supplicant does not know
	  about

2008-11-01 - v0.6.5
	* added support for SHA-256 as X.509 certificate digest when using the
	  internal X.509/TLSv1 implementation
	* updated management frame protection to use IEEE 802.11w/D6.0
	* added support for using SHA256-based stronger key derivation for WPA2
	  (IEEE 802.11w)
	* fixed FT (IEEE 802.11r) authentication after a failed association to
	  use correct FTIE
	* added support for configuring Phase 2 (inner/tunneled) authentication
	  method with wpa_gui-qt4

2008-08-10 - v0.6.4
	* added support for EAP Sequences in EAP-FAST Phase 2
	* added support for using TNC with EAP-FAST
	* added driver_ps3 for the PS3 Linux wireless driver
	* added support for optional cryptobinding with PEAPv0
	* fixed the OpenSSL patches (0.9.8g and 0.9.9) for EAP-FAST to
	  allow fallback to full handshake if server rejects PAC-Opaque
	* added fragmentation support for EAP-TNC
	* added support for parsing PKCS #8 formatted private keys into the
	  internal TLS implementation (both PKCS #1 RSA key and PKCS #8
	  encapsulated RSA key can now be used)
	* added option of using faster, but larger, routines in the internal
	  LibTomMath (for internal TLS implementation) to speed up DH and RSA
	  calculations (CONFIG_INTERNAL_LIBTOMMATH_FAST=y)
	* fixed race condition between disassociation event and group key
	  handshake to avoid getting stuck in incorrect state [Bug 261]
	* fixed opportunistic key caching (proactive_key_caching)

2008-02-22 - v0.6.3
	* removed 'nai' and 'eappsk' network configuration variables that were
	  previously used for configuring user identity and key for EAP-PSK,
	  EAP-PAX, EAP-SAKE, and EAP-GPSK. 'identity' field is now used as the
	  replacement for 'nai' (if old configuration used a separate
	  'identity' value, that would now be configured as
	  'anonymous_identity'). 'password' field is now used as the
	  replacement for 'eappsk' (it can also be set using hexstring to
	  present random binary data)
	* removed '-w' command line parameter (wait for interface to be added,
	  if needed); cleaner way of handling this functionality is to use an
	  external mechanism (e.g., hotplug scripts) that start wpa_supplicant
	  when an interface is added
	* updated FT support to use the latest draft, IEEE 802.11r/D9.0
	* added ctrl_iface monitor event (CTRL-EVENT-SCAN-RESULTS) for
	  indicating when new scan results become available
	* added new ctrl_iface command, BSS, to allow scan results to be
	  fetched without hitting the message size limits (this command
	  can be used to iterate through the scan results one BSS at the time)
	* fixed EAP-SIM not to include AT_NONCE_MT and AT_SELECTED_VERSION
	  attributes in EAP-SIM Start/Response when using fast reauthentication
	* fixed EAPOL not to end up in infinite loop when processing dynamic
	  WEP keys with IEEE 802.1X
	* fixed problems in getting NDIS events from WMI on Windows 2000

2008-01-01 - v0.6.2
	* added support for Makefile builds to include debug-log-to-a-file
	  functionality (CONFIG_DEBUG_FILE=y and -f<path> on command line)
	* fixed EAP-SIM and EAP-AKA message parser to validate attribute
	  lengths properly to avoid potential crash caused by invalid messages
	* added data structure for storing allocated buffers (struct wpabuf);
	  this does not affect wpa_supplicant usage, but many of the APIs
	  changed and various interfaces (e.g., EAP) is not compatible with old
	  versions
	* added support for protecting EAP-AKA/Identity messages with
	  AT_CHECKCODE (optional feature in RFC 4187)
	* added support for protected result indication with AT_RESULT_IND for
	  EAP-SIM and EAP-AKA (phase1="result_ind=1")
	* added driver_wext workaround for race condition between scanning and
	  association with drivers that take very long time to scan all
	  channels (e.g., madwifi with dual-band cards); wpa_supplicant is now
	  using a longer hardcoded timeout for the scan if the driver supports
	  notifications for scan completion (SIOCGIWSCAN event); this helps,
	  e.g., in cases where wpa_supplicant and madwifi driver ended up in
	  loop where the driver did not even try to associate
	* stop EAPOL timer tick when no timers are in use in order to reduce
	  power consumption (no need to wake up the process once per second)
	  [Bug 237]
	* added support for privilege separation (run only minimal part of
	  wpa_supplicant functionality as root and rest as unprivileged,
	  non-root process); see 'Privilege separation' in README for details;
	  this is disabled by default and can be enabled with CONFIG_PRIVSEP=y
	  in .config
	* changed scan results data structure to include all information
	  elements to make it easier to support new IEs; old get_scan_result()
	  driver_ops is still supported for backwards compatibility (results
	  are converted internally to the new format), but all drivers should
	  start using the new get_scan_results2() to make them more likely to
	  work with new features
	* Qt4 version of wpa_gui (wpa_gui-qt4 subdirectory) is now native Qt4
	  application, i.e., it does not require Qt3Support anymore; Windows
	  binary of wpa_gui.exe is now from this directory and only requires
	  QtCore4.dll and QtGui4.dll libraries
	* updated Windows binary build to use Qt 4.3.3 and made Qt DLLs
	  available as a separate package to make wpa_gui installation easier:
	  http://w1.fi/wpa_supplicant/qt4/wpa_gui-qt433-windows-dll.zip
	* added support for EAP-IKEv2 (draft-tschofenig-eap-ikev2-15.txt);
	  only shared key/password authentication is supported in this version

2007-11-24 - v0.6.1
	* added support for configuring password as NtPasswordHash
	  (16-byte MD4 hash of password) in hash:<32 hex digits> format
	* added support for fallback from abbreviated TLS handshake to
	  full handshake when using EAP-FAST (e.g., due to an expired
	  PAC-Opaque)
	* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
	  draft (draft-ietf-emu-eap-gpsk-07.txt)
	* added support for drivers that take care of RSN 4-way handshake
	  internally (WPA_DRIVER_FLAGS_4WAY_HANDSHAKE in get_capa flags and
	  WPA_ALG_PMK in set_key)
	* added an experimental port for Mac OS X (CONFIG_DRIVER_OSX=y in
	  .config); this version supports only ap_scan=2 mode and allow the
	  driver to take care of the 4-way handshake
	* fixed a buffer overflow in parsing TSF from scan results when using
	  driver_wext.c with a driver that includes the TSF (e.g., iwl4965)
	  [Bug 232]
	* updated FT support to use the latest draft, IEEE 802.11r/D8.0
	* fixed an integer overflow issue in the ASN.1 parser used by the
	  (experimental) internal TLS implementation to avoid a potential
	  buffer read overflow
	* fixed a race condition with -W option (wait for a control interface
	  monitor before starting) that could have caused the first messages to
	  be lost
	* added support for processing TNCC-TNCS-Messages to report
	  recommendation (allow/none/isolate) when using TNC [Bug 243]

2007-05-28 - v0.6.0
	* added network configuration parameter 'frequency' for setting
	  initial channel for IBSS (adhoc) networks
	* added experimental IEEE 802.11r/D6.0 support
	* updated EAP-SAKE to RFC 4763 and the IANA-allocated EAP type 48
	* updated EAP-PSK to use the IANA-allocated EAP type 47
	* fixed EAP-PAX key derivation
	* fixed EAP-PSK bit ordering of the Flags field
	* fixed EAP-PEAP/TTLS/FAST to use the correct EAP identifier in
	  tunnelled identity request (previously, the identifier from the outer
	  method was used, not the tunnelled identifier which could be
	  different)
	* added support for fragmentation of outer TLS packets during Phase 2
	  of EAP-PEAP/TTLS/FAST
	* fixed EAP-TTLS AVP parser processing for too short AVP lengths
	* added support for EAP-FAST authentication with inner methods that
	  generate MSK (e.g., EAP-MSCHAPv2 that was previously only supported
	  for PAC provisioning)
	* added support for authenticated EAP-FAST provisioning
	* added support for configuring maximum number of EAP-FAST PACs to
	  store in a PAC list (fast_max_pac_list_len=<max> in phase1 string)
	* added support for storing EAP-FAST PACs in binary format
	  (fast_pac_format=binary in phase1 string)
	* fixed dbus ctrl_iface to validate message interface before
	  dispatching to avoid a possible segfault [Bug 190]
	* fixed PeerKey key derivation to use the correct PRF label
	* updated Windows binary build to link against OpenSSL 0.9.8d and
	  added support for EAP-FAST
	* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
	  draft (draft-ietf-emu-eap-gpsk-04.txt)
	* fixed EAP-AKA Notification processing to allow Notification to be
	  processed after AKA Challenge response has been sent
	* updated to use IEEE 802.11w/D2.0 for management frame protection
	  (still experimental)
	* fixed EAP-TTLS implementation not to crash on use of freed memory
	  if TLS library initialization fails
	* added support for EAP-TNC (Trusted Network Connect)
	  (this version implements the EAP-TNC method and EAP-TTLS changes
	  needed to run two methods in sequence (IF-T) and the IF-IMC and
	  IF-TNCCS interfaces from TNCC)

2006-11-24 - v0.5.6
	* added experimental, integrated TLSv1 client implementation with the
	  needed X.509/ASN.1/RSA/bignum processing (this can be enabled by
	  setting CONFIG_TLS=internal and CONFIG_INTERNAL_LIBTOMMATH=y in
	  .config); this can be useful, e.g., if the target system does not
	  have a suitable TLS library and a minimal code size is required
	  (total size of this internal TLS/crypto code is bit under 50 kB on
	  x86 and the crypto code is shared by rest of the supplicant so some
	  of it was already required; TLSv1/X.509/ASN.1/RSA added about 25 kB)
	* removed STAKey handshake since PeerKey handshake has replaced it in
	  IEEE 802.11ma and there are no known deployments of STAKey
	* updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest
	  draft (draft-ietf-emu-eap-gpsk-01.txt)
	* added preliminary implementation of IEEE 802.11w/D1.0 (management
	  frame protection)
	  (Note: this requires driver support to work properly.)
	  (Note2: IEEE 802.11w is an unapproved draft and subject to change.)
	* fixed Windows named pipes ctrl_iface to not stop listening for
	  commands if client program opens a named pipe and closes it
	  immediately without sending a command
	* fixed USIM PIN status determination for the case that PIN is not
	  needed (this allows EAP-AKA to be used with USIM cards that do not
	  use PIN)
	* added support for reading 3G USIM AID from EF_DIR to allow EAP-AKA to
	  be used with cards that do not support file selection based on
	  partial AID
	* added support for matching the subjectAltName of the authentication
	  server certificate against multiple name components (e.g.,
	  altsubject_match="DNS:server.example.com;DNS:server2.example.com")
	* fixed EAP-SIM/AKA key derivation for re-authentication case (only
	  affects IEEE 802.1X with dynamic WEP keys)
	* changed ctrl_iface network configuration 'get' operations to not
	  return password/key material; if these fields are requested, "*"
	  will be returned if the password/key is set, but the value of the
	  parameter is not exposed

2006-08-27 - v0.5.5
	* added support for building Windows version with UNICODE defined
	  (wide-char functions)
	* driver_ndis: fixed static WEP configuration to avoid race condition
	  issues with some NDIS drivers between association and setting WEP
	  keys
	* driver_ndis: added validation for IELength value in scan results to
	  avoid crashes when using buggy NDIS drivers [Bug 165]
	* fixed Release|Win32 target in the Visual Studio project files
	  (previously, only Debug|Win32 target was set properly)
	* changed control interface API call wpa_ctrl_pending() to allow it to
	  return -1 on error (e.g., connection lost); control interface clients
	  will need to make sure that they verify that the value is indeed >0
	  when determining whether there are pending messages
	* added an alternative control interface backend for Windows targets:
	  Named Pipe (CONFIG_CTRL_IFACE=named_pipe); this is now the default
	  control interface mechanism for Windows builds (previously, UDP to
	  localhost was used)
	* changed ctrl_interface configuration for UNIX domain sockets:
	  - deprecated ctrl_interface_group variable (it may be removed in
	    future versions)
	  - allow both directory and group be configured with ctrl_interface
	    in following format: DIR=/var/run/wpa_supplicant GROUP=wheel
	  - ctrl_interface=/var/run/wpa_supplicant is still supported for the
	    case when group is not changed
	* added support for controlling more than one interface per process in
	  Windows version
	* added a workaround for a case where the AP is using unknown address
	  (e.g., MAC address of the wired interface) as the source address for
	  EAPOL-Key frames; previously, that source address was used as the
	  destination for EAPOL-Key frames and in key derivation; now, BSSID is
	  used even if the source address does not match with it
	  (this resolves an interoperability issue with Thomson SpeedTouch 580)
	* added a workaround for UDP-based control interface (which was used in
	  Windows builds before this release) to prevent packets with forged
	  addresses from being accepted as local control requests
	* removed ndis_events.cpp and possibility of using external
	  ndis_events.exe; C version (ndis_events.c) is fully functional and
	  there is no desire to maintain two separate versions of this
	  implementation
	* ndis_events: Changed NDIS event notification design to use WMI to
	  learn the adapter description through Win32_PnPEntity class; this
	  should fix some cases where the adapter name was not recognized
	  correctly (e.g., with some USB WLAN adapters, e.g., Ralink RT2500
	  USB) [Bug 113]
	* fixed selection of the first network in ap_scan=2 mode; previously,
	  wpa_supplicant could get stuck in SCANNING state when only the first
	  network for enabled (e.g., after 'wpa_cli select_network 0')
	* winsvc: added support for configuring ctrl_interface parameters in
	  registry (ctrl_interface string value in
	  HKLM\SOFTWARE\wpa_supplicant\interfaces\0000 key); this new value is
	  required to enable control interface (previously, this was hardcoded
	  to be enabled)
	* allow wpa_gui subdirectory to be built with both Qt3 and Qt4
	* converted wpa_gui-qt4 subdirectory to use Qt4 specific project format

2006-06-20 - v0.5.4
	* fixed build with CONFIG_STAKEY=y [Bug 143]
	* added support for doing MLME (IEEE 802.11 management frame
	  processing) in wpa_supplicant when using Devicescape IEEE 802.11
	  stack (wireless-dev.git tree)
	* added a new network block configuration option, fragment_size, to
	  configure the maximum EAP fragment size
	* driver_ndis: Disable WZC automatically for the selected interface to
	  avoid conflicts with two programs trying to control the radio; WZC
	  will be re-enabled (if it was enabled originally) when wpa_supplicant
	  is terminated
	* added an experimental TLSv1 client implementation
	  (CONFIG_TLS=internal) that can be used instead of an external TLS
	  library, e.g., to reduce total size requirement on systems that do
	  not include any TLS library by default (this is not yet complete;
	  basic functionality is there, but certificate validation is not yet
	  included)
	* added PeerKey handshake implementation for IEEE 802.11e
	  direct link setup (DLS) to replace STAKey handshake
	* fixed WPA PSK update through ctrl_iface for the case where the old
	  PSK was derived from an ASCII passphrase and the new PSK is set as
	  a raw PSK (hex string)
	* added new configuration option for identifying which network block
	  was used (id_str in wpa_supplicant.conf; included on
	  WPA_EVENT_CONNECT monitor event and as WPA_ID_STR environmental
	  variable in wpa_cli action scripts; in addition WPA_ID variable is
	  set to the current unique identifier that wpa_supplicant assigned
	  automatically for the network and that can be used with
	  GET_NETWORK/SET_NETWORK ctrl_iface commands)
	* wpa_cli action script is now called only when the connect/disconnect
	  status changes or when associating with a different network
	* fixed configuration parser not to remove CCMP from group cipher list
	  if WPA-None (adhoc) is used (pairwise=NONE in that case)
	* fixed integrated NDIS events processing not to hang the process due
	  to a missed change in eloop_win.c API in v0.5.3 [Bug 155]
	* added support for EAP Generalized Pre-Shared Key (EAP-GPSK,
	  draft-clancy-emu-eap-shared-secret-00.txt)
	* added Microsoft Visual Studio 2005 solution and project files for
	  build wpa_supplicant for Windows (see vs2005 subdirectory)
	* eloop_win: fixed unregistration of Windows events
	* l2_packet_winpcap: fixed a deadlock in deinitializing l2_packet
	  at the end of RSN pre-authentication and added unregistration of
	  a Windows event to avoid getting eloop_win stuck with an invalid
	  handle
	* driver_ndis: added support for selecting AP based on BSSID
	* added new environmental variable for wpa_cli action scripts:
	  WPA_CTRL_DIR is the current control interface directory
	* driver_ndis: added support for using NDISUIO instead of WinPcap for
	  OID set/query operations (CONFIG_USE_NDISUIO=y in .config); with new
	  l2_packet_ndis (CONFIG_L2_PACKET=ndis), this can be used to build
	  wpa_supplicant without requiring WinPcap; note that using NDISUIO
	  requires that WZC is disabled (net stop wzcsvc) since NDISUIO allows
	  only one application to open the device
	* changed NDIS driver naming to only include device GUID, e.g.,
	  {7EE3EFE5-C165-472F-986D-F6FBEDFE8C8D}, instead of including WinPcap
	  specific \Device\NPF_ prefix before the GUID; the prefix is still
	  allowed for backwards compatibility, but it is not required anymore
	  when specifying the interface
	* driver_ndis: re-initialize driver interface is the adapter is removed
	  and re-inserted [Bug 159]
	* driver_madwifi: fixed TKIP and CCMP sequence number configuration on
	  big endian hosts [Bug 146]

2006-04-27 - v0.5.3
	* fixed EAP-GTC response to include correct user identity when run as
	  phase 2 method of EAP-FAST (i.e., EAP-FAST did not work in v0.5.2)
	* driver_ndis: Fixed encryption mode configuration for unencrypted
	  networks (some NDIS drivers ignored this, but others, e.g., Broadcom,
	  refused to associate with open networks) [Bug 106]
	* driver_ndis: use BSSID OID polling to detect when IBSS network is
	  formed even when ndis_events code is included since some NDIS drivers
	  do not generate media connect events in IBSS mode
	* config_winreg: allow global ctrl_interface parameter to be configured
	  in Windows registry
	* config_winreg: added support for saving configuration data into
	  Windows registry
	* added support for controlling network device operational state
	  (dormant/up) for Linux 2.6.17 to improve DHCP processing (see
	  http://www.flamewarmaster.de/software/dhcpclient/ for a DHCP client
	  that can use this information)
	* driver_wext: added support for WE-21 change to SSID configuration
	* driver_wext: fixed privacy configuration for static WEP keys mode
	  [Bug 140]
	* added an optional driver_ops callback for MLME-SETPROTECTION.request
	  primitive
	* added support for EAP-SAKE (no EAP method number allocated yet, so
	  this is using the same experimental type 255 as EAP-PSK)
	* added support for dynamically loading EAP methods (.so files) instead
	  of requiring them to be statically linked in; this is disabled by
	  default (see CONFIG_DYNAMIC_EAP_METHODS in defconfig for information
	  on how to use this)

2006-03-19 - v0.5.2
	* do not try to use USIM APDUs when initializing PC/SC for SIM card
	  access for a network that has not enabled EAP-AKA
	* fixed EAP phase 2 Nak for EAP-{PEAP,TTLS,FAST} (this was broken in
	  v0.5.1 due to the new support for expanded EAP types)
	* added support for generating EAP Expanded Nak
	* try to fetch scan results once before requesting new scan when
	  starting up in ap_scan=1 mode (this can speed up initial association
	  a lot with, e.g., madwifi-ng driver)
	* added support for receiving EAPOL frames from a Linux bridge
	  interface (-bbr0 on command line)
	* fixed EAPOL re-authentication for sessions that used PMKSA caching
	* changed EAP method registration to use a dynamic list of methods
	  instead of a static list generated at build time
	* fixed PMKSA cache deinitialization not to use freed memory when
	  removing PMKSA entries
	* fixed a memory leak in EAP-TTLS re-authentication
	* reject WPA/WPA2 message 3/4 if it does not include any valid
	  WPA/RSN IE
	* driver_wext: added fallback to use SIOCSIWENCODE for setting auth_alg
	  if the driver does not support SIOCSIWAUTH

2006-01-29 - v0.5.1
	* driver_test: added better support for multiple APs and STAs by using
	  a directory with sockets that include MAC address for each device in
	  the name (driver_param=test_dir=/tmp/test)
	* added support for EAP expanded type (vendor specific EAP methods)
	* added AP_SCAN command into ctrl_iface so that ap_scan configuration
	  option can be changed if needed
	* wpa_cli/wpa_gui: skip non-socket files in control directory when
	  using UNIX domain sockets; this avoids selecting an incorrect
	  interface (e.g., a PID file could be in this directory, even though
	  use of this directory for something else than socket files is not
	  recommended)
	* fixed TLS library deinitialization after RSN pre-authentication not
	  to disable TLS library for normal authentication
	* driver_wext: Remove null-termination from SSID length if the driver
	  used it; some Linux drivers do this and they were causing problems in
	  wpa_supplicant not finding matching configuration block. This change
	  would break a case where the SSID actually ends in '\0', but that is
	  not likely to happen in real use.
	* fixed PMKSA cache processing not to trigger deauthentication if the
	  current PMKSA cache entry is replaced with a valid new entry
	* fixed PC/SC initialization for ap_scan != 1 modes (this fixes
	  EAP-SIM and EAP-AKA with real SIM/USIM card when using ap_scan=0 or
	  ap_scan=2)

2005-12-18 - v0.5.0 (beginning of 0.5.x development releases)
	* added experimental STAKey handshake implementation for IEEE 802.11e
	  direct link setup (DLS); note: this is disabled by default in both
	  build and runtime configuration (can be enabled with CONFIG_STAKEY=y
	  and stakey=1)
	* fixed EAP-SIM and EAP-AKA pseudonym and fast re-authentication to
	  decrypt AT_ENCR_DATA attributes correctly
	* fixed EAP-AKA to allow resynchronization within the same session
	* made code closer to ANSI C89 standard to make it easier to port to
	  other C libraries and compilers
	* started moving operating system or C library specific functions into
	  wrapper functions defined in os.h and implemented in os_*.c to make
	  code more portable
	* wpa_supplicant can now be built with Microsoft Visual C++
	  (e.g., with the freely available Toolkit 2003 version or Visual
	  C++ 2005 Express Edition and Platform SDK); see nmake.mak for an
	  example makefile for nmake
	* added support for using Windows registry for command line parameters
	  (CONFIG_MAIN=main_winsvc) and configuration data
	  (CONFIG_BACKEND=winreg); see win_example.reg for an example registry
	  contents; this version can be run both as a Windows service and as a
	  normal application; 'wpasvc.exe app' to start as applicant,
	  'wpasvc.exe reg <full path to wpasvc.exe>' to register a service,
	  'net start wpasvc' to start the service, 'wpasvc.exe unreg' to
	  unregister a service
	* made it possible to link ndis_events.exe functionality into
	  wpa_supplicant.exe by defining CONFIG_NDIS_EVENTS_INTEGRATED
	* added better support for multiple control interface backends
	  (CONFIG_CTRL_IFACE option); currently, 'unix' and 'udp' are supported
	* fixed PC/SC code to use correct length for GSM AUTH command buffer
	  and to not use pioRecvPci with SCardTransmit() calls; these were not
	  causing visible problems with pcsc-lite, but Windows Winscard.dll
	  refused the previously used parameters; this fixes EAP-SIM and
	  EAP-AKA authentication using SIM/USIM card under Windows
	* added new event loop implementation for Windows using
	  WaitForMultipleObject() instead of select() in order to allow waiting
	  for non-socket objects; this can be selected with
	  CONFIG_ELOOP=eloop_win in .config
	* added support for selecting l2_packet implementation in .config
	  (CONFIG_L2_PACKET; following options are available now: linux, pcap,
	  winpcap, freebsd, none)
	* added new l2_packet implementation for WinPcap
	  (CONFIG_L2_PACKET=winpcap) that uses a separate receive thread to
	  reduce latency in EAPOL receive processing from about 100 ms to about
	  3 ms
	* added support for EAP-FAST key derivation using other ciphers than
	  RC4-128-SHA for authentication and AES128-SHA for provisioning
	* added support for configuring CA certificate as DER file and as a
	  configuration blob
	* fixed private key configuration as configuration blob and added
	  support for using PKCS#12 as a blob
	* tls_gnutls: added support for using PKCS#12 files; added support for
	  session resumption
	* added support for loading trusted CA certificates from Windows
	  certificate store: ca_cert="cert_store://<name>", where <name> is
	  likely CA (Intermediate CA certificates) or ROOT (root certificates)
	* added C version of ndis_events.cpp and made it possible to build this
	  with MinGW so that CONFIG_NDIS_EVENTS_INTEGRATED can be used more
	  easily on cross-compilation builds
	* added wpasvc.exe into Windows binary release; this is an alternative
	  version of wpa_supplicant.exe with configuration backend using
	  Windows registry and with the entry point designed to run as a
	  Windows service
	* integrated ndis_events.exe functionality into wpa_supplicant.exe and
	  wpasvc.exe and removed this additional tool from the Windows binary
	  release since it is not needed anymore
	* load winscard.dll functions dynamically when building with MinGW
	  since MinGW does not yet include winscard library

2005-11-20 - v0.4.7 (beginning of 0.4.x stable releases)
	* l2_packet_pcap: fixed wired IEEE 802.1X authentication with libpcap
	  and WinPcap to receive frames sent to PAE group address
	* disable EAP state machine when IEEE 802.1X authentication is not used
	  in order to get rid of bogus "EAP failed" messages
	* fixed OpenSSL error reporting to go through all pending errors to
	  avoid confusing reports of old errors being reported at later point
	  during handshake
	* fixed configuration file updating to not write empty variables
	  (e.g., proto or key_mgmt) that the file parser would not accept
	* fixed ADD_NETWORK ctrl_iface command to use the same default values
	  for variables as empty network definitions read from config file
	  would get
	* fixed EAP state machine to not discard EAP-Failure messages in many
	  cases (e.g., during TLS handshake)
	* fixed a infinite loop in private key reading if the configured file
	  cannot be parsed successfully
	* driver_madwifi: added support for madwifi-ng
	* wpa_gui: do not display password/PSK field contents
	* wpa_gui: added CA certificate configuration
	* driver_ndis: fixed scan request in ap_scan=2 mode not to change SSID
	* driver_ndis: include Beacon IEs in AssocInfo in order to notice if
	  the new AP is using different WPA/RSN IE
	* use longer timeout for IEEE 802.11 association to avoid problems with
	  drivers that may take more than five second to associate

2005-10-27 - v0.4.6
	* allow fallback to WPA, if mixed WPA+WPA2 networks have mismatch in
	  RSN IE, but WPA IE would match with wpa_supplicant configuration
	* added support for named configuration blobs in order to avoid having
	  to use file system for external files (e.g., certificates);
	  variables can be set to "blob://<blob name>" instead of file path to
	  use a named blob; supported fields: pac_file, client_cert,
	  private_key
	* fixed RSN pre-authentication (it was broken in the clean up of WPA
	  state machine interface in v0.4.5)
	* driver_madwifi: set IEEE80211_KEY_GROUP flag for group keys to make
	  sure the driver configures broadcast decryption correctly
	* added ca_path (and ca_path2) configuration variables that can be used
	  to configure OpenSSL CA path, e.g., /etc/ssl/certs, for using the
	  system-wide trusted CA list
	* added support for starting wpa_supplicant without a configuration
	  file (-C argument must be used to set ctrl_interface parameter for
	  this case; in addition, -p argument can be used to provide
	  driver_param; these new arguments can also be used with a
	  configuration to override the values from the configuration)
	* added global control interface that can be optionally used for adding
	  and removing network interfaces dynamically (-g command line argument
	  for both wpa_supplicant and wpa_cli) without having to restart
	  wpa_supplicant process
	* wpa_gui:
	  - try to save configuration whenever something is modified
	  - added WEP key configuration
	  - added possibility to edit the current network configuration
	* driver_ndis: fixed driver polling not to increase frequency on each
	  received EAPOL frame due to incorrectly cancelled timeout
	* added simple configuration file examples (in examples subdirectory)
	* fixed driver_wext.c to filter wireless events based on ifindex to
	  avoid interfaces receiving events from other interfaces
	* delay sending initial EAPOL-Start couple of seconds to speed up
	  authentication for the most common case of Authenticator starting
	  EAP authentication immediately after association

2005-09-25 - v0.4.5
	* added a workaround for clearing keys with ndiswrapper to allow
	  roaming from WPA enabled AP to plaintext one
	* added docbook documentation (doc/docbook) that can be used to
	  generate, e.g., man pages
	* l2_packet_linux: use socket type SOCK_DGRAM instead of SOCK_RAW for
	  PF_PACKET in order to prepare for network devices that do not use
	  Ethernet headers (e.g., network stack with native IEEE 802.11 frames)
	* use receipt of EAPOL-Key frame as a lower layer success indication
	  for EAP state machine to allow recovery from dropped EAP-Success
	  frame
	* cleaned up internal EAPOL frame processing by not including link
	  layer (Ethernet) header during WPA and EAPOL/EAP processing; this
	  header is added only when transmitted the frame; this makes it easier
	  to use wpa_supplicant on link layers that use different header than
	  Ethernet
	* updated EAP-PSK to use draft 9 by default since this can now be
	  tested with hostapd; removed support for draft 3, including
	  server_nai configuration option from network blocks
	* driver_wired: add PAE address to the multicast address list in order
	  to be able to receive EAPOL frames with drivers that do not include
	  these multicast addresses by default
	* driver_wext: add support for WE-19
	* added support for multiple configuration backends (CONFIG_BACKEND
	  option); currently, only 'file' is supported (i.e., the format used
	  in wpa_supplicant.conf)
	* added support for updating configuration ('wpa_cli save_config');
	  this is disabled by default and can be enabled with global
	  update_config=1 variable in wpa_supplicant.conf; this allows wpa_cli
	  and wpa_gui to store the configuration changes in a permanent store
	* added GET_NETWORK ctrl_iface command
	  (e.g., 'wpa_cli get_network 0 ssid')

2005-08-21 - v0.4.4
	* replaced OpenSSL patch for EAP-FAST support
	  (openssl-tls-extensions.patch) with a more generic and correct
	  patch (the new patch is not compatible with the previous one, so the
	  OpenSSL library will need to be patched with the new patch in order
	  to be able to build wpa_supplicant with EAP-FAST support)
	* added support for using Windows certificate store (through CryptoAPI)
	  for client certificate and private key operations (EAP-TLS)
	  (see wpa_supplicant.conf for more information on how to configure
	  this with private_key)
	* ported wpa_gui to Windows
	* added Qt4 version of wpa_gui (wpa_gui-qt4 directory); this can be
	  built with the open source version of the Qt4 for Windows
	* allow non-WPA modes (e.g., IEEE 802.1X with dynamic WEP) to be used
	  with drivers that do not support WPA
	* ndis_events: fixed Windows 2000 support
	* added support for enabling/disabling networks from the list of all
	  configured networks ('wpa_cli enable_network <network id>' and
	  'wpa_cli disable_network <network id>')
	* added support for adding and removing network from the current
	  configuration ('wpa_cli add_network' and 'wpa_cli remove_network
	  <network id>'); added networks are disabled by default and they can
	  be enabled with enable_network command once the configuration is done
	  for the new network; note: configuration file is not yet updated, so
	  these new networks are lost when wpa_supplicant is restarted
	* added support for setting network configuration parameters through
	  the control interface, for example:
	  wpa_cli set_network 0 ssid "\"my network\""
	* fixed parsing of strings that include both " and # within double
	  quoted area (e.g., "start"#end")
	* added EAP workaround for PEAP session resumption: allow outer,
	  i.e., not tunneled, EAP-Success to terminate session since; this can
	  be disabled with eap_workaround=0
	  (this was allowed for PEAPv1 before, but now it is also allowed for
	  PEAPv0 since at least one RADIUS authentication server seems to be
	  doing this for PEAPv0, too)
	* wpa_gui: added preliminary support for adding new networks to the
	  wpa_supplicant configuration (double click on the scan results to
	  open network configuration)

2005-06-26 - v0.4.3
	* removed interface for external EAPOL/EAP supplicant (e.g.,
	  Xsupplicant), (CONFIG_XSUPPLICANT_IFACE) since it is not required
	  anymore and is unlikely to be used by anyone
	* driver_ndis: fixed WinPcap 3.0 support
	* fixed build with CONFIG_DNET_PCAP=y on Linux
	* l2_packet: moved different implementations into separate files
	  (l2_packet_*.c)

2005-06-12 - v0.4.2
	* driver_ipw: updated driver structures to match with ipw2200-1.0.4
	  (note: ipw2100-1.1.0 is likely to require an update to work with
	  this)
	* added support for using ap_scan=2 mode with multiple network blocks;
	  wpa_supplicant will go through the networks one by one until the
	  driver reports a successful association; this uses the same order for
	  networks as scan_ssid=1 scans, i.e., the priority field is ignored
	  and the network block order in the file is used instead
	* fixed a potential issue in RSN pre-authentication ending up using
	  freed memory if pre-authentication times out
	* added support for matching alternative subject name extensions of the
	  authentication server certificate; new configuration variables
	  altsubject_match and altsubject_match2
	* driver_ndis: added support for IEEE 802.1X authentication with wired
	  NDIS drivers
	* added support for querying private key password (EAP-TLS) through the
	  control interface (wpa_cli/wpa_gui) if one is not included in the
	  configuration file
	* driver_broadcom: fixed couple of memory leaks in scan result
	  processing
	* EAP-PAX is now registered as EAP type 46
	* fixed EAP-PAX MAC calculation
	* fixed EAP-PAX CK and ICK key derivation
	* added support for using password with EAP-PAX (as an alternative to
	  entering key with eappsk); SHA-1 hash of the password will be used as
	  the key in this case
	* added support for arbitrary driver interface parameters through the
	  configuration file with a new driver_param field; this adds a new
	  driver_ops function set_param()
	* added possibility to override l2_packet module with driver interface
	  API (new send_eapol handler); this can be used to implement driver
	  specific TX/RX functions for EAPOL frames
	* fixed ctrl_interface_group processing for the case where gid is
	  entered as a number, not group name
	* driver_test: added support for testing hostapd with wpa_supplicant
	  by using test driver interface without any kernel drivers or network
	  cards

2005-05-22 - v0.4.1
	* driver_madwifi: fixed WPA/WPA2 mode configuration to allow EAPOL
	  packets to be encrypted; this was apparently broken by the changed
	  ioctl order in v0.4.0
	* driver_madwifi: added preliminary support for compiling against 'BSD'
	  branch of madwifi CVS tree
	* added support for EAP-MSCHAPv2 password retries within the same EAP
	  authentication session
	* added support for password changes with EAP-MSCHAPv2 (used when the
	  password has expired)
	* added support for reading additional certificates from PKCS#12 files
	  and adding them to the certificate chain
	* fixed association with IEEE 802.1X (no WPA) when dynamic WEP keys
	  were used
	* fixed a possible double free in EAP-TTLS fast-reauthentication when
	  identity or password is entered through control interface
	* display EAP Notification messages to user through control interface
	  with "CTRL-EVENT-EAP-NOTIFICATION" prefix
	* added GUI version of wpa_cli, wpa_gui; this is not build
	  automatically with 'make'; use 'make wpa_gui' to build (this requires
	  Qt development tools)
	* added 'disconnect' command to control interface for setting
	  wpa_supplicant in state where it will not associate before
	  'reassociate' command has been used
	* added support for selecting a network from the list of all configured
	  networks ('wpa_cli select_network <network id>'; this disabled all
	  other networks; to re-enable, 'wpa_cli select_network any')
	* added support for getting scan results through control interface
	* added EAP workaround for PEAPv1 session resumption: allow outer,
	  i.e., not tunneled, EAP-Success to terminate session since; this can
	  be disabled with eap_workaround=0

2005-04-25 - v0.4.0 (beginning of 0.4.x development releases)
	* added a new build time option, CONFIG_NO_STDOUT_DEBUG, that can be
	  used to reduce the size of the wpa_supplicant considerably if
	  debugging code is not needed
	* fixed EAPOL-Key validation to drop packets with invalid Key Data
	  Length; such frames could have crashed wpa_supplicant due to buffer
	  overflow
	* added support for wired authentication (IEEE 802.1X on wired
	  Ethernet); driver interface 'wired'
	* obsoleted set_wpa() handler in the driver interface API (it can be
	  replaced by moving enable/disable functionality into init()/deinit())
	  (calls to set_wpa() are still present for backwards compatibility,
	  but they may be removed in the future)
	* driver_madwifi: fixed association in plaintext mode
	* modified the EAP workaround that accepts EAP-Success with incorrect
	  Identifier to be even less strict about verification in order to
	  interoperate with some authentication servers
	* added support for sending TLS alerts
	* added support for 'any' SSID wildcard; if ssid is not configured or
	  is set to an empty string, any SSID will be accepted for non-WPA AP
	* added support for asking PIN (for SIM) from frontends (e.g.,
	  wpa_cli); if a PIN is needed, but not included in the configuration
	  file, a control interface request is sent and EAP processing is
	  delayed until the PIN is available
	* added support for using external devices (e.g., a smartcard) for
	  private key operations in EAP-TLS (CONFIG_SMARTCARD=y in .config);
	  new wpa_supplicant.conf variables:
	  - global: opensc_engine_path, pkcs11_engine_path, pkcs11_module_path
	  - network: engine, engine_id, key_id
	* added experimental support for EAP-PAX
	* added monitor mode for wpa_cli (-a<path to a program to run>) that
	  allows external commands (e.g., shell scripts) to be run based on
	  wpa_supplicant events, e.g., when authentication has been completed
	  and data connection is ready; other related wpa_cli arguments:
	  -B (run in background), -P (write PID file); wpa_supplicant has a new
	  command line argument (-W) that can be used to make it wait until a
	  control interface command is received in order to avoid missing
	  events
	* added support for opportunistic WPA2 PMKSA key caching (disabled by
	  default, can be enabled with proactive_key_caching=1)
	* fixed RSN IE in 4-Way Handshake message 2/4 for the case where
	  Authenticator rejects PMKSA caching attempt and the driver is not
	  using assoc_info events
	* added -P<pid file> argument for wpa_supplicant to write the current
	  process id into a file

2005-02-12 - v0.3.7 (beginning of 0.3.x stable releases)
	* added new phase1 option parameter, include_tls_length=1, to force
	  wpa_supplicant to add TLS Message Length field to all TLS messages
	  even if the packet is not fragmented; this may be needed with some
	  authentication servers
	* fixed WPA/RSN IE verification in message 3 of 4-Way Handshake when
	  using drivers that take care of AP selection (e.g., when using
	  ap_scan=2)
	* fixed reprocessing of pending request after ctrl_iface requests for
	  identity/password/otp
	* fixed ctrl_iface requests for identity/password/otp in Phase 2 of
	  EAP-PEAP and EAP-TTLS
	* all drivers using driver_wext: set interface up and select Managed
	  mode when starting wpa_supplicant; set interface down when exiting
	* renamed driver_ipw2100.c to driver_ipw.c since it now supports both
	  ipw2100 and ipw2200; please note that this also changed the
	  configuration variable in .config to CONFIG_DRIVER_IPW

2005-01-24 - v0.3.6
	* fixed a busy loop introduced in v0.3.5 for scan result processing
	  when no matching AP is found

2005-01-23 - v0.3.5
	* added a workaround for an interoperability issue with a Cisco AP
	  when using WPA2-PSK
	* fixed non-WPA IEEE 802.1X to use the same authentication timeout as
	  WPA with IEEE 802.1X (i.e., timeout 10 -> 70 sec to allow
	  retransmission of dropped frames)
	* fixed issues with 64-bit CPUs and SHA1 cleanup in previous version
	  (e.g., segfault when processing EAPOL-Key frames)
	* fixed EAP workaround and fast reauthentication configuration for
	  RSN pre-authentication; previously these were disabled and
	  pre-authentication would fail if the used authentication server
	  requires EAP workarounds
	* added support for blacklisting APs that fail or timeout
	  authentication in ap_scan=1 mode so that all APs are tried in cases
	  where the ones with strongest signal level are failing authentication
	* fixed CA certificate loading after a failed EAP-TLS/PEAP/TTLS
	  authentication attempt
	* allow EAP-PEAP/TTLS fast reauthentication only if Phase 2 succeeded
	  in the previous authentication (previously, only Phase 1 success was
	  verified)

2005-01-09 - v0.3.4
	* added preliminary support for IBSS (ad-hoc) mode configuration
	  (mode=1 in network block); this included a new key_mgmt mode
	  WPA-NONE, i.e., TKIP or CCMP with a fixed key (based on psk) and no
	  key management; see wpa_supplicant.conf for more details and an
	  example on how to configure this (note: this is currently implemented
	  only for driver_hostapd.c, but the changes should be trivial to add
	  in associate() handler for other drivers, too (assuming the driver
	  supports WPA-None)
	* added preliminary port for native Windows (i.e., no cygwin) using
	  mingw

2005-01-02 - v0.3.3
	* added optional support for GNU Readline and History Libraries for
	  wpa_cli (CONFIG_READLINE)
	* cleaned up EAP state machine <-> method interface and number of
	  small problems with error case processing not terminating on
	  EAP-Failure but waiting for timeout
	* added couple of workarounds for interoperability issues with a
	  Cisco AP when using WPA2
	* added support for EAP-FAST (draft-cam-winget-eap-fast-00.txt);
	  Note: This requires a patch for openssl to add support for TLS
	  extensions and number of workarounds for operations without
	  certificates. Proof of concept type of experimental patch is
	  included in openssl-tls-extensions.patch.

2004-12-19 - v0.3.2
	* fixed private key loading for cases where passphrase is not set
	* fixed Windows/cygwin L2 packet handler freeing; previous version
	  could cause a segfault when RSN pre-authentication was completed
	* added support for PMKSA caching with drivers that generate RSN IEs
	  (e.g., NDIS); currently, this is only implemented in driver_ndis.c,
	  but similar code can be easily added to driver_ndiswrapper.c once
	  ndiswrapper gets full support for RSN PMKSA caching
	* improved recovery from PMKID mismatches by requesting full EAP
	  authentication in case of failed PMKSA caching attempt
	* driver_ndis: added support for NDIS NdisMIncidateStatus() events
	  (this requires that ndis_events is ran while wpa_supplicant is
	  running)
	* driver_ndis: use ADD_WEP/REMOVE_WEP when configuring WEP keys
	* added support for driver interfaces to replace the interface name
	  based on driver/OS specific mapping, e.g., in case of driver_ndis,
	  this allows the beginning of the adapter description to be used as
	  the interface name
	* added support for CR+LF (Windows-style) line ends in configuration
	  file
	* driver_ndis: enable radio before starting scanning, disable radio
	  when exiting
	* modified association event handler to set portEnabled = FALSE before
	  clearing port Valid in order to reset EAP state machine and avoid
	  problems with new authentication getting ignored because of state
	  machines ending up in AUTHENTICATED/SUCCESS state based on old
	  information
	* added support for driver events to add PMKID candidates in order to
	  allow drivers to give priority to most likely roaming candidates
	* driver_hostap: moved PrivacyInvoked configuration to associate()
	  function so that this will not be set for plaintext connections
	* added KEY_MGMT_802_1X_NO_WPA as a new key_mgmt type so that driver
	  interface can distinguish plaintext and IEEE 802.1X (no WPA)
	  authentication
	* fixed static WEP key configuration to use broadcast/default type for
	  all keys (previously, the default TX key was configured as pairwise/
	  unicast key)
	* driver_ndis: added legacy WPA capability detection for non-WPA2
	  drivers
	* added support for setting static WEP keys for IEEE 802.1X without
	  dynamic WEP keying (eapol_flags=0)

2004-12-12 - v0.3.1
	* added support for reading PKCS#12 (PFX) files (as a replacement for
	  PEM/DER) to get certificate and private key (CONFIG_PKCS12)
	* fixed compilation with CONFIG_PCSC=y
	* added new ap_scan mode, ap_scan=2, for drivers that take care of
	  association, but need to be configured with security policy and SSID,
	  e.g., ndiswrapper and NDIS driver; this mode should allow such
	  drivers to work with hidden SSIDs and optimized roaming; when
	  ap_scan=2 is used, only the first network block in the configuration
	  file is used and this configuration should have explicit security
	  policy (i.e., only one option in the lists) for key_mgmt, pairwise,
	  group, proto variables
	* added experimental port of wpa_supplicant for Windows
	  - driver_ndis.c driver interface (NDIS OIDs)
	  - currently, this requires cygwin and WinPcap
	  - small utility, win_if_list, can be used to get interface name
	* control interface can now be removed at build time; add
	  CONFIG_CTRL_IFACE=y to .config to maintain old functionality
	* optional Xsupplicant interface can now be removed at build time;
	  (CONFIG_XSUPPLICANT_IFACE=y in .config to bring it back)
	* added auth_alg to driver interface associate() parameters to make it
	  easier for drivers to configure authentication algorithm as part of
	  the association

2004-12-05 - v0.3.0 (beginning of 0.3.x development releases)
	* driver_broadcom: added new driver interface for Broadcom wl.o driver
	  (a generic driver for Broadcom IEEE 802.11a/g cards)
	* wpa_cli: fixed parsing of -p <path> command line argument
	* PEAPv1: fixed tunneled EAP-Success reply handling to reply with TLS
	  ACK, not tunneled EAP-Success (of which only the first byte was
	  actually send due to a bug in previous code); this seems to
	  interoperate with most RADIUS servers that implements PEAPv1
	* PEAPv1: added support for terminating PEAP authentication on tunneled
	  EAP-Success message; this can be configured by adding
	  peap_outer_success=0 on phase1 parameters in wpa_supplicant.conf
	  (some RADIUS servers require this whereas others require a tunneled
	  reply
	* PEAPv1: changed phase1 option peaplabel to use default to 0, i.e., to
	  the old label for key derivation; previously, the default was 1,
	  but it looks like most existing PEAPv1 implementations use the old
	  label which is thus more suitable default option
	* added support for EAP-PSK (draft-bersani-eap-psk-03.txt)
	* fixed parsing of wep_tx_keyidx
	* added support for configuring list of allowed Phase 2 EAP types
	  (for both EAP-PEAP and EAP-TTLS) instead of only one type
	* added support for configuring IEEE 802.11 authentication algorithm
	  (auth_alg; mainly for using Shared Key authentication with static
	  WEP keys)
	* added support for EAP-AKA (with UMTS SIM)
	* fixed couple of errors in PCSC handling that could have caused
	  random-looking errors for EAP-SIM
	* added support for EAP-SIM pseudonyms and fast re-authentication
	* added support for EAP-TLS/PEAP/TTLS fast re-authentication (TLS
	  session resumption)
	* added support for EAP-SIM with two challanges
	  (phase1="sim_min_num_chal=3" can be used to require three challenges)
	* added support for configuring DH/DSA parameters for an ephemeral DH
	  key exchange (EAP-TLS/PEAP/TTLS) using new configuration parameters
	  dh_file and dh_file2 (phase 2); this adds support for using DSA keys
	  and optional DH key exchange to achieve forward secracy with RSA keys
	* added support for matching subject of the authentication server
	  certificate with a substring when using EAP-TLS/PEAP/TTLS; new
	  configuration variables subject_match and subject_match2
	* changed SSID configuration in driver_wext.c (used by many driver
	  interfaces) to use ssid_len+1 as the length for SSID since some Linux
	  drivers expect this
	* fixed couple of unaligned reads in scan result parsing to fix WPA
	  connection on some platforms (e.g., ARM)
	* added driver interface for Intel ipw2100 driver
	* added support for LEAP with WPA
	* added support for larger scan results report (old limit was 4 kB of
	  data, i.e., about 35 or so APs) when using Linux wireless extensions
	  v17 or newer
	* fixed a bug in PMKSA cache processing: skip sending of EAPOL-Start
	  only if there is a PMKSA cache entry for the current AP
	* fixed error handling for case where reading of scan results fails:
	  must schedule a new scan or wpa_supplicant will remain waiting
	  forever
	* changed debug output to remove shared password/key material by
	  default; all key information can be included with -K command line
	  argument to match the previous behavior
	* added support for timestamping debug log messages (disabled by
	  default, can be enabled with -t command line argument)
	* set pairwise/group cipher suite for non-WPA IEEE 802.1X to WEP-104
	  if keys are not configured to be used; this fixes IEEE 802.1X mode
	  with drivers that use this information to configure whether Privacy
	  bit can be in Beacon frames (e.g., ndiswrapper)
	* avoid clearing driver keys if no keys have been configured since last
	  key clear request; this seems to improve reliability of group key
	  handshake for ndiswrapper & NDIS driver which seems to be suffering
	  of some kind of timing issue when the keys are cleared again after
	  association
	* changed driver interface API:
	  - WPA_SUPPLICANT_DRIVER_VERSION define can be used to determine which
	    version is being used (now, this is set to 2; previously, it was
	    not defined)
	  - pass pointer to private data structure to all calls
	  - the new API is not backwards compatible; all in-tree driver
	    interfaces has been converted to the new API
	* added support for controlling multiple interfaces (radios) per
	  wpa_supplicant process; each interface needs to be listed on the
	  command line (-c, -i, -D arguments) with -N as a separator
	  (-cwpa1.conf -iwlan0 -Dhostap -N -cwpa2.conf -iath0 -Dmadwifi)
	* added a workaround for EAP servers that incorrectly use same Id for
	  sequential EAP packets
	* changed libpcap/libdnet configuration to use .config variable,
	  CONFIG_DNET_PCAP, instead of requiring Makefile modification
	* improved downgrade attack detection in IE verification of msg 3/4:
	  verify both WPA and RSN IEs, if present, not only the selected one;
	  reject the AP if an RSN IE is found in msg 3/4, but not in Beacon or
	  Probe Response frame, and RSN is enabled in wpa_supplicant
	  configuration
	* fixed WPA msg 3/4 processing to allow Key Data field contain other
	  IEs than just one WPA IE
	* added support for FreeBSD and driver interface for the BSD net80211
	  layer (CONFIG_DRIVER_BSD=y in .config); please note that some of the
	  required kernel mods have not yet been committed
	* made EAP workarounds configurable; enabled by default, can be
	  disabled with network block option eap_workaround=0

2004-07-17 - v0.2.4 (beginning of 0.2.x stable releases)
	* resolved couple of interoperability issues with EAP-PEAPv1 and
	  Phase 2 (inner EAP) fragment reassembly
	* driver_madwifi: fixed WEP key configuration for IEEE 802.1X when the
	  AP is using non-zero key index for the unicast key and key index zero
	  for the broadcast key
	* driver_hostap: fixed IEEE 802.1X WEP key updates and
	  re-authentication by allowing unencrypted EAPOL frames when not using
	  WPA
	* added a new driver interface, 'wext', which uses only standard,
	  driver independent functionality in Linux wireless extensions;
	  currently, this can be used only for non-WPA IEEE 802.1X mode, but
	  eventually, this is to be extended to support full WPA/WPA2 once
	  Linux wireless extensions get support for this
	* added support for mode in which the driver is responsible for AP
	  scanning and selection; this is disabled by default and can be
	  enabled with global ap_scan=0 variable in wpa_supplicant.conf;
	  this mode can be used, e.g., with generic 'wext' driver interface to
	  use wpa_supplicant as IEEE 802.1X Supplicant with any Linux driver
	  supporting wireless extensions.
	* driver_madwifi: fixed WPA2 configuration and scan_ssid=1 (e.g.,
	  operation with an AP that does not include SSID in the Beacon frames)
	* added support for new EAP authentication methods:
	  EAP-TTLS/EAP-OTP, EAP-PEAPv0/OTP, EAP-PEAPv1/OTP, EAP-OTP
	* added support for asking one-time-passwords from frontends (e.g.,
	  wpa_cli); this 'otp' command works otherwise like 'password' command,
	  but the password is used only once and the frontend will be asked for
	  a new password whenever a request from authenticator requires a
	  password; this can be used with both EAP-OTP and EAP-GTC
	* changed wpa_cli to automatically re-establish connection so that it
	  does not need to be re-started when wpa_supplicant is terminated and
	  started again
	* improved user data (identity/password/otp) requests through
	  frontends: process pending EAPOL packets after getting new
	  information so that full authentication does not need to be
	  restarted; in addition, send pending requests again whenever a new
	  frontend is attached
	* changed control frontends to use a new directory for socket files to
	  make it easier for wpa_cli to automatically select between interfaces
	  and to provide access control for the control interface;
	  wpa_supplicant.conf: ctrl_interface is now a path
	  (/var/run/wpa_supplicant is the recommended path) and
	  ctrl_interface_group can be used to select which group gets access to
	  the control interface;
	  wpa_cli: by default, try to connect to the first interface available
	  in /var/run/wpa_supplicant; this path can be overriden with -p option
	  and an interface can be selected with -i option (i.e., in most common
	  cases, wpa_cli does not need to get any arguments)
	* added support for LEAP
	* added driver interface for Linux ndiswrapper
	* added priority option for network blocks in the configuration file;
	  this allows networks to be grouped based on priority (the scan
	  results are searched for matches with network blocks in this order)

2004-06-20 - v0.2.3
	* sort scan results to improve AP selection
	* fixed control interface socket removal for some error cases
	* improved scan requesting and authentication timeout
	* small improvements/bug fixes for EAP-MSCHAPv2, EAP-PEAP, and
	  TLS processing
	* PEAP version can now be forced with phase1="peapver=<ver>"
	  (mostly for testing; by default, the highest version supported by
	  both the Supplicant and Authentication Server is selected
	  automatically)
	* added support for madwifi driver (Atheros ar521x)
	* added a workaround for cases where AP sets Install Tx/Rx bit for
	  WPA Group Key messages when pairwise keys are used (without this,
	  the Group Key would be used for Tx and the AP would drop frames
	  from the station)
	* added GSM SIM/USIM interface for GSM authentication algorithm for
	  EAP-SIM; this requires pcsc-lite
	* added support for ATMEL AT76C5XXx driver
	* fixed IEEE 802.1X WEP key derivation in the case where Authenticator
	  does not include key data in the EAPOL-Key frame (i.e., part of
	  EAP keying material is used as data encryption key)
	* added support for using plaintext and static WEP networks
	  (key_mgmt=NONE)

2004-05-31 - v0.2.2
	* added support for new EAP authentication methods:
	  EAP-TTLS/EAP-MD5-Challenge
	  EAP-TTLS/EAP-GTC
	  EAP-TTLS/EAP-MSCHAPv2
	  EAP-TTLS/EAP-TLS
	  EAP-TTLS/MSCHAPv2
	  EAP-TTLS/MSCHAP
	  EAP-TTLS/PAP
	  EAP-TTLS/CHAP
	  EAP-PEAP/TLS
	  EAP-PEAP/GTC
	  EAP-PEAP/MD5-Challenge
	  EAP-GTC
	  EAP-SIM (not yet complete; needs GSM/SIM authentication interface)
	* added support for anonymous identity (to be used when identity is
	  sent in plaintext; real identity will be used within TLS protected
	  tunnel (e.g., with EAP-TTLS)
	* added event messages from wpa_supplicant to frontends, e.g., wpa_cli
	* added support for requesting identity and password information using
	  control interface; in other words, the password for EAP-PEAP or
	  EAP-TTLS does not need to be included in the configuration file since
	  a frontand (e.g., wpa_cli) can ask it from the user
	* improved RSN pre-authentication to use a candidate list and process
	  all candidates from each scan; not only one per scan
	* fixed RSN IE and WPA IE capabilities field parsing
	* ignore Tx bit in GTK IE when Pairwise keys are used
	* avoid making new scan requests during IEEE 802.1X negotiation
	* use openssl/libcrypto for MD5 and SHA-1 when compiling wpa_supplicant
	  with TLS support (this replaces the included implementation with
	  library code to save about 8 kB since the library code is needed
	  anyway for TLS)
	* fixed WPA-PSK only mode when compiled without IEEE 802.1X support
	  (i.e., without CONFIG_IEEE8021X_EAPOL=y in .config)

2004-05-06 - v0.2.1
	* added support for internal IEEE 802.1X (actually, IEEE 802.1aa/D6.1)
	  Supplicant
	  - EAPOL state machines for Supplicant [IEEE 802.1aa/D6.1]
	  - EAP peer state machine [draft-ietf-eap-statemachine-02.pdf]
	  - EAP-MD5 (cannot be used with WPA-RADIUS)
	    [draft-ietf-eap-rfc2284bis-09.txt]
	  - EAP-TLS [RFC 2716]
	  - EAP-MSCHAPv2 (currently used only with EAP-PEAP)
	  - EAP-PEAP/MSCHAPv2 [draft-josefsson-pppext-eap-tls-eap-07.txt]
	    [draft-kamath-pppext-eap-mschapv2-00.txt]
	    (PEAP version 0, 1, and parts of 2; only 0 and 1 are enabled by
	    default; tested with FreeRADIUS, Microsoft IAS, and Funk Odyssey)
	  - new configuration file options: eap, identity, password, ca_cert,
	    client_cert, privatekey, private_key_passwd
	  - Xsupplicant is not required anymore, but it can be used by
	    disabling the internal IEEE 802.1X Supplicant with -e command line
	    option
	  - this code is not included in the default build; Makefile need to
	    be edited for this (uncomment lines for selected functionality)
	  - EAP-TLS and EAP-PEAP require openssl libraries
	* use module prefix in debug messages (WPA, EAP, EAP-TLS, ..)
	* added support for non-WPA IEEE 802.1X mode with dynamic WEP keys
	  (i.e., complete IEEE 802.1X/EAP authentication and use IEEE 802.1X
	   EAPOL-Key frames instead of WPA key handshakes)
	* added support for IEEE 802.11i/RSN (WPA2)
	  - improved PTK Key Handshake
	  - PMKSA caching, pre-authentication
	* fixed wpa_supplicant to ignore possible extra data after WPA
	  EAPOL-Key packets (this fixes 'Invalid EAPOL-Key MIC when using
	  TPTK' error from message 3 of 4-Way Handshake in case the AP
	  includes extra data after the EAPOL-Key)
	* added interface for external programs (frontends) to control
	  wpa_supplicant
	  - CLI example (wpa_cli) with interactive mode and command line
	    mode
	  - replaced SIGUSR1 status/statistics with the new control interface
	* made some feature compile time configurable
	  - .config file for make
	  - driver interfaces (hostap, hermes, ..)
	  - EAPOL/EAP functions

2004-02-15 - v0.2.0
	* Initial version of wpa_supplicant