1 /* 2 * Qualcomm Atheros OUI and vendor specific assignments 3 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc. 4 * Copyright (c) 2018-2020, The Linux Foundation 5 * 6 * This software may be distributed under the terms of the BSD license. 7 * See README for more details. 8 */ 9 10 #ifndef QCA_VENDOR_H 11 #define QCA_VENDOR_H 12 13 /* 14 * This file is a registry of identifier assignments from the Qualcomm Atheros 15 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers 16 * can be assigned through normal review process for changes to the upstream 17 * hostap.git repository. 18 */ 19 20 #define OUI_QCA 0x001374 21 22 #ifndef BIT 23 #define BIT(x) (1U << (x)) 24 #endif 25 26 /** 27 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs 28 */ 29 enum qca_radiotap_vendor_ids { 30 QCA_RADIOTAP_VID_WLANTEST = 0, 31 }; 32 33 /** 34 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers 35 * 36 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0 37 * 38 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event 39 * 40 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use 41 * internal BSS-selection. This command uses 42 * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy 43 * for the current connection (i.e., changes policy set by the nl80211 44 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be 45 * included to indicate which BSS to use in case roaming is disabled. 46 * 47 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency 48 * ranges to avoid to reduce issues due to interference or internal 49 * co-existence information in the driver. These frequencies aim to 50 * minimize the traffic but not to totally avoid the traffic. That said 51 * for a P2P use case, these frequencies are allowed for the P2P 52 * discovery/negotiation but avoid the group to get formed on these 53 * frequencies. The event data structure is defined in 54 * struct qca_avoid_freq_list. 55 * 56 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support 57 * for DFS offloading. 58 * 59 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass 60 * NAN Request/Response and NAN Indication messages. These messages are 61 * interpreted between the framework and the firmware component. While 62 * sending the command from userspace to the driver, payload is not 63 * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN 64 * is used when receiving vendor events in userspace from the driver. 65 * 66 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be 67 * used to configure PMK to the driver even when not connected. This can 68 * be used to request offloading of key management operations. Only used 69 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 70 * 71 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of 72 * NL80211_CMD_ROAM event with optional attributes including information 73 * from offloaded key management operation. Uses 74 * enum qca_wlan_vendor_attr_roam_auth attributes. Only used 75 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 76 * 77 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to 78 * invoke the ACS function in device and pass selected channels to 79 * hostapd. Uses enum qca_wlan_vendor_attr_acs_offload attributes. 80 * 81 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features 82 * supported by the driver. enum qca_wlan_vendor_features defines 83 * the possible features. 84 * 85 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver, 86 * which supports DFS offloading, to indicate a channel availability check 87 * start. 88 * 89 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver, 90 * which supports DFS offloading, to indicate a channel availability check 91 * completion. 92 * 93 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver, 94 * which supports DFS offloading, to indicate that the channel availability 95 * check aborted, no change to the channel status. 96 * 97 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by 98 * driver, which supports DFS offloading, to indicate that the 99 * Non-Occupancy Period for this channel is over, channel becomes usable. 100 * 101 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver, 102 * which supports DFS offloading, to indicate a radar pattern has been 103 * detected. The channel is now unusable. 104 * 105 * @QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO: Get information from the driver. 106 * Attributes defined in enum qca_wlan_vendor_attr_get_wifi_info. 107 * 108 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap 109 * based on enum wifi_logger_supported_features. Attributes defined in 110 * enum qca_wlan_vendor_attr_get_logger_features. 111 * 112 * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular 113 * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the 114 * attribute for this command. Attributes defined in 115 * enum qca_wlan_vendor_attr_wifi_logger_start. 116 * 117 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS 118 * capabilities of the driver, parameters includes the attributes defined 119 * in enum qca_wlan_vendor_attr_tdls_get_capabilities. 120 * 121 * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload 122 * sending of certain periodic IP packet to firmware, attributes defined in 123 * enum qca_wlan_vendor_attr_offloaded_packets. 124 * 125 * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI 126 * monitoring, defines min and max RSSI which are configured for RSSI 127 * monitoring. Also used to notify the RSSI breach and provides the BSSID 128 * and RSSI value that was breached. Attributes defined in 129 * enum qca_wlan_vendor_attr_rssi_monitoring. 130 * 131 * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN 132 * Data Path (NDP) related operations, attributes defined in 133 * enum qca_wlan_vendor_attr_ndp_params. 134 * 135 * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable 136 * Neighbour Discovery offload, attributes defined in 137 * enum qca_wlan_vendor_attr_nd_offload. 138 * 139 * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various 140 * configuration parameter for BPF packet filter, attributes defined in 141 * enum qca_wlan_vendor_attr_packet_filter. 142 * 143 * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware 144 * maximum supported size, attributes defined in 145 * enum qca_wlan_vendor_drv_info. 146 * 147 * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various 148 * data about wake reasons and datapath IP statistics, attributes defined 149 * in enum qca_wlan_vendor_attr_wake_stats. 150 * 151 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration 152 * for IEEE 802.11 communicating outside the context of a basic service 153 * set, called OCB command. Uses the attributes defines in 154 * enum qca_wlan_vendor_attr_ocb_set_config. 155 * 156 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB 157 * UTC time. Use the attributes defines in 158 * enum qca_wlan_vendor_attr_ocb_set_utc_time. 159 * 160 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start 161 * sending OCB timing advert frames. Uses the attributes defines in 162 * enum qca_wlan_vendor_attr_ocb_start_timing_advert. 163 * 164 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop 165 * OCB timing advert. Uses the attributes defines in 166 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert. 167 * 168 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF 169 * timer value. Uses the attributes defines in 170 * enum qca_wlan_vendor_attr_ocb_get_tsf_resp. 171 * 172 * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the 173 * link properties of the respective interface. As an event, is used 174 * to notify the connected station's status. The attributes for this 175 * command are defined in enum qca_wlan_vendor_attr_link_properties. 176 * 177 * @QCA_NL80211_VENDOR_SUBCMD_SETBAND: Command to configure the enabled band(s) 178 * to the driver. This command sets the band(s) through either the 179 * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE or 180 * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK (or both). 181 * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE refers enum qca_set_band as unsigned 182 * integer values and QCA_WLAN_VENDOR_ATTR_SETBAND_MASK refers it as 32 183 * bit unsigned bitmask values. The allowed values for 184 * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE are limited to QCA_SETBAND_AUTO, 185 * QCA_SETBAND_5G, and QCA_SETBAND_2G. Other values/bitmasks are valid for 186 * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. The attribute 187 * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE is deprecated and the recommendation 188 * is to use the QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. If the both attributes 189 * are included for backwards compatibility, the configurations through 190 * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK will take the precedence with drivers 191 * that support both attributes. 192 * 193 * @QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY: This command is used to configure 194 * DFS policy and channel hint for ACS operation. This command uses the 195 * attributes defined in enum qca_wlan_vendor_attr_acs_config and 196 * enum qca_acs_dfs_mode. 197 * 198 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to 199 * start the P2P Listen offload function in device and pass the listen 200 * channel, period, interval, count, device types, and vendor specific 201 * information elements to the device driver and firmware. 202 * Uses the attributes defines in 203 * enum qca_wlan_vendor_attr_p2p_listen_offload. 204 * 205 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to 206 * indicate stop request/response of the P2P Listen offload function in 207 * device. As an event, it indicates either the feature stopped after it 208 * was already running or feature has actually failed to start. Uses the 209 * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload. 210 * 211 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts 212 * beaconing, this sub command provides the driver, the frequencies on the 213 * 5 GHz band to check for any radar activity. Driver selects one channel 214 * from this priority list provided through 215 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts 216 * to check for radar activity on it. If no radar activity is detected 217 * during the channel availability check period, driver internally switches 218 * to the selected frequency of operation. If the frequency is zero, driver 219 * internally selects a channel. The status of this conditional switch is 220 * indicated through an event using the same sub command through 221 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are 222 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch. 223 * 224 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the 225 * attributes defined in enum qca_wlan_gpio_attr. 226 * 227 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities. 228 * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which 229 * capabilities are to be fetched and other 230 * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the 231 * requested capabilities. 232 * 233 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension. 234 * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this 235 * command and event. 236 * 237 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for 238 * indoor location features. Capabilities are reported in 239 * QCA_WLAN_VENDOR_ATTR_LOC_CAPA. 240 * 241 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM 242 * (fine timing measurement) session with one or more peers. 243 * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and 244 * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS. 245 * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT 246 * events will be reported, followed by 247 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate 248 * end of session. 249 * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6 250 * 251 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session. 252 * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with 253 * status code indicating session was aborted. 254 * 255 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement 256 * results for one peer. Results are reported in 257 * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS. 258 * 259 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when 260 * FTM session is finished, either successfully or aborted by 261 * request. 262 * 263 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder 264 * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether 265 * to enable or disable the responder. LCI/LCR reports can be 266 * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and 267 * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple 268 * times to update the LCI/LCR reports. 269 * 270 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of 271 * arrival) measurement with a single peer. Specify peer MAC address in 272 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in 273 * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel 274 * scan results cache and use the frequency from there). 275 * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE. 276 * Measurement result is reported in 277 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event. 278 * 279 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify 280 * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 281 * 282 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports 283 * the AOA measurement result. 284 * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 285 * success/failure status is reported in 286 * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS. 287 * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 288 * The antenna array(s) used in the measurement are reported in 289 * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK. 290 * 291 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given 292 * data as per the given parameters. 293 * 294 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a 295 * specific chain. 296 * 297 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level 298 * configuration for a DMG RF sector. Specify sector index in 299 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 300 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules 301 * to return sector information for in 302 * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration 303 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the 304 * exact time where information was captured in 305 * QCA_WLAN_VENDOR_ATTR_TSF. 306 * 307 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level 308 * configuration for a DMG RF sector. Specify sector index in 309 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 310 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration 311 * for one or more DMG RF modules in 312 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. 313 * 314 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected 315 * DMG RF sector for a station. This is the sector that the HW 316 * will use to communicate with the station. Specify the MAC address 317 * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not 318 * needed for unassociated station). Specify sector type to return in 319 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected 320 * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 321 * Also return the exact time where the information was captured 322 * in QCA_WLAN_VENDOR_ATTR_TSF. 323 * 324 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the 325 * selected DMG RF sector for a station. This is the sector that 326 * the HW will use to communicate with the station. 327 * Specify the MAC address of associated station/AP/PCP in 328 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in 329 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index 330 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 331 * The selected sector will be locked such that it will not be 332 * modified like it normally does (for example when station 333 * moves around). To unlock the selected sector for a station 334 * pass the special value 0xFFFF in the sector index. To unlock 335 * all connected stations also pass a broadcast MAC address. 336 * 337 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior 338 * in the host driver. The different TDLS configurations are defined 339 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. 340 * 341 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE 342 * capabilities. The response uses the attributes defined in 343 * enum qca_wlan_vendor_attr_get_he_capabilities. 344 * 345 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was 346 * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command 347 * carries the scan cookie of the corresponding scan request. The scan 348 * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE. 349 * 350 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific 351 * Absorption Rate (SAR) power limits. A critical regulation for 352 * FCC compliance, OEMs require methods to set SAR limits on TX 353 * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits 354 * attributes are used with this command. 355 * 356 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the 357 * host driver for offloading the implementation of Auto Channel Selection 358 * (ACS) to an external user space entity. This interface is used as the 359 * event from the host driver to the user space entity and also as the 360 * request from the user space entity to the host driver. The event from 361 * the host driver is used by the user space entity as an indication to 362 * start the ACS functionality. The attributes used by this event are 363 * represented by the enum qca_wlan_vendor_attr_external_acs_event. 364 * User space entity uses the same interface to inform the host driver with 365 * selected channels after the ACS operation using the attributes defined 366 * by enum qca_wlan_vendor_attr_external_acs_channels. 367 * 368 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the 369 * requisite information leading to a power save failure. The information 370 * carried as part of this event is represented by the 371 * enum qca_attr_chip_power_save_failure attributes. 372 * 373 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics 374 * collection. Uses attributes defined in enum qca_attr_nud_stats_set. 375 * 376 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These 377 * statistics are represented by the enum qca_attr_nud_stats_get 378 * attributes. 379 * 380 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch 381 * the BSS transition status, whether accept or reject, for a list of 382 * candidate BSSIDs provided by the userspace. This uses the vendor 383 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and 384 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify 385 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an 386 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in 387 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response 388 * the driver shall specify array of 389 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and 390 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in 391 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. 392 * 393 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a 394 * specific QCA module. The trace levels are represented by 395 * enum qca_attr_trace_level attributes. 396 * 397 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement 398 * Protocol antenna limit in different modes. See enum 399 * qca_wlan_vendor_attr_brp_ant_limit_mode. 400 * 401 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan 402 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. 403 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) 404 * identifying the operation in success case. In failure cases an 405 * error code (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE) 406 * describing the reason for the failure is returned. 407 * 408 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses 409 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from 410 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to 411 * be stopped. 412 * 413 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the 414 * specific interface. This can be used to modify some of the low level 415 * scan parameters (off channel dwell time, home channel time) in the 416 * driver/firmware. These parameters are maintained within the host driver. 417 * This command is valid only when the interface is in the connected state. 418 * These scan parameters shall be reset by the driver/firmware once 419 * disconnected. The attributes used with this command are defined in 420 * enum qca_wlan_vendor_attr_active_tos. 421 * 422 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the 423 * driver has detected an internal failure. This event carries the 424 * information indicating the reason that triggered this detection. The 425 * attributes for this command are defined in 426 * enum qca_wlan_vendor_attr_hang. 427 * 428 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values 429 * of spectral parameters used. The spectral scan parameters are specified 430 * by enum qca_wlan_vendor_attr_spectral_scan. 431 * 432 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats 433 * for spectral scan functionality. The debug stats are specified by 434 * enum qca_wlan_vendor_attr_spectral_diag_stats. 435 * 436 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral 437 * scan system capabilities. The capabilities are specified 438 * by enum qca_wlan_vendor_attr_spectral_cap. 439 * 440 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current 441 * status of spectral scan. The status values are specified 442 * by enum qca_wlan_vendor_attr_spectral_scan_status. 443 * 444 * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush 445 * peer pending packets. Specify the peer MAC address in 446 * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets 447 * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed 448 * in enum qca_wlan_vendor_attr_flush_pending. 449 * 450 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative 451 * RF Operating Parameter (RROP) information. The attributes for this 452 * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is 453 * intended for use by external Auto Channel Selection applications. 454 * 455 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate 456 * (SAR) power limits. This is a companion to the command 457 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the 458 * settings currently in use. The attributes returned by this command are 459 * defined by enum qca_vendor_attr_sar_limits. 460 * 461 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of 462 * the WLAN hardware MAC. Also, provides the WLAN netdev interface 463 * information attached to the respective MAC. 464 * This works both as a query (user space asks the current mode) or event 465 * interface (driver advertising the current mode to the user space). 466 * Driver does not trigger this event for temporary hardware mode changes. 467 * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion, 468 * channel change, etc.) are updated with this event. Attributes for this 469 * interface are defined in enum qca_wlan_vendor_attr_mac. 470 * 471 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold 472 * per peer per TID. Attributes for this command are define in 473 * enum qca_wlan_set_qdepth_thresh_attr. 474 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action 475 * guide for WLAN driver. Request to suspend of driver and FW if the 476 * temperature is higher than the suspend threshold; resume action is 477 * requested to driver if the temperature is lower than the resume 478 * threshold. In user poll mode, request temperature data by user. For test 479 * purpose, getting thermal shutdown configuration parameters is needed. 480 * Attributes for this interface are defined in 481 * enum qca_wlan_vendor_attr_thermal_cmd. 482 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from 483 * driver. Thermal temperature and indication of resume completion are 484 * reported as thermal events. The attributes for this command are defined 485 * in enum qca_wlan_vendor_attr_thermal_event. 486 * 487 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi 488 * test configuration. Attributes for this command are defined in 489 * enum qca_wlan_vendor_attr_wifi_test_config. 490 * 491 * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an 492 * RX filter to receive frames from stations that are active on the 493 * operating channel, but not associated with the local device (e.g., STAs 494 * associated with other APs). Filtering is done based on a list of BSSIDs 495 * and STA MAC addresses added by the user. This command is also used to 496 * fetch the statistics of unassociated stations. The attributes used with 497 * this command are defined in enum qca_wlan_vendor_attr_bss_filter. 498 * 499 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor 500 * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, 501 * carried a payload which was a binary blob of data. The command was not 502 * extendable to send more information. The newer version carries the 503 * legacy blob encapsulated within an attribute and can be extended with 504 * additional vendor attributes that can enhance the NAN command interface. 505 * @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered 506 * or stopped within driver/firmware in order to initiate roaming. The 507 * attributes used with this event are defined in enum 508 * qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events 509 * in few cases, e.g., if the host processor is sleeping when this event 510 * is generated in firmware. 511 * 512 * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to 513 * configure parameters per peer to capture Channel Frequency Response 514 * (CFR) and enable Periodic CFR capture. The attributes for this command 515 * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. This command 516 * can also be used to send CFR data from the driver to userspace when 517 * netlink events are used to send CFR data. 518 * 519 * @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes 520 * in throughput dynamically. The driver estimates the throughput based on 521 * number of packets being transmitted/received per second and indicates 522 * the changes in throughput to user space. Userspace tools can use this 523 * information to configure kernel's TCP parameters in order to achieve 524 * peak throughput. Optionally, the driver will also send guidance on 525 * modifications to kernel's TCP parameters which can be referred by 526 * userspace tools. The attributes used with this event are defined in enum 527 * qca_wlan_vendor_attr_throughput_change. 528 * 529 * @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set 530 * priorities among different types of traffic during coex scenarios. 531 * Current supported prioritization is among WLAN/BT/ZIGBEE with different 532 * profiles mentioned in enum qca_coex_config_profiles. The associated 533 * attributes used with this command are defined in enum 534 * qca_vendor_attr_coex_config. 535 * 536 * Based on the config provided, FW will boost the weight and prioritize 537 * the traffic for that subsystem (WLAN/BT/Zigbee). 538 * 539 * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS: This command is used to query 540 * the supported AKM suite selectorss from the driver. It returns the list 541 * of supported AKMs in the attribute NL80211_ATTR_AKM_SUITES. 542 * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: This command is used to get firmware 543 * state from the driver. It returns the firmware state in the attribute 544 * QCA_WLAN_VENDOR_ATTR_FW_STATE. 545 * @QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH: This vendor subcommand 546 * is used by the driver to flush per-peer cached statistics to user space 547 * application. This interface is used as an event from the driver to 548 * user space application. Attributes for this event are specified in 549 * enum qca_wlan_vendor_attr_peer_stats_cache_params. 550 * QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA attribute is expected to be 551 * sent in the event. 552 * @QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG: This sub command is used to 553 * improve the success rate of Zigbee joining network. 554 * Due to PTA master limitation, Zigbee joining network success rate is 555 * low while WLAN is working. The WLAN driver needs to configure some 556 * parameters including Zigbee state and specific WLAN periods to enhance 557 * PTA master. All these parameters are delivered by the attributes 558 * defined in enum qca_mpta_helper_vendor_attr. 559 * @QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING: This sub command is used to 560 * implement Beacon frame reporting feature. 561 * 562 * Userspace can request the driver/firmware to periodically report 563 * received Beacon frames whose BSSID is same as the current connected 564 * BSS's MAC address. 565 * 566 * In case the STA seamlessly (without sending disconnect indication to 567 * userspace) roams to a different BSS, Beacon frame reporting will be 568 * automatically enabled for the Beacon frames whose BSSID is same as the 569 * MAC address of the new BSS. Beacon reporting will be stopped when the 570 * STA is disconnected (when the disconnect indication is sent to 571 * userspace) and need to be explicitly enabled by userspace for next 572 * connection. 573 * 574 * When a Beacon frame matching configured conditions is received, and if 575 * userspace has requested to send asynchronous beacon reports, the 576 * driver/firmware will encapsulate the details of the Beacon frame in an 577 * event and send it to userspace along with updating the BSS information 578 * in cfg80211 scan cache, otherwise driver will only update the cfg80211 579 * scan cache with the information from the received Beacon frame but will 580 * not send any active report to userspace. 581 * 582 * The userspace can request the driver/firmware to stop reporting Beacon 583 * frames. If the driver/firmware is not able to receive Beacon frames due 584 * to other Wi-Fi operations such as off-channel activities, etc., the 585 * driver/firmware will send a pause event to userspace and stop reporting 586 * Beacon frames. Whether the beacon reporting will be automatically 587 * resumed or not by the driver/firmware later will be reported to 588 * userspace using the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES 589 * flag. The beacon reporting shall be resumed for all the cases except 590 * either when userspace sets 591 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME flag in the command 592 * which triggered the current beacon reporting or during any disconnection 593 * case as indicated by setting 594 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON to 595 * QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED by the 596 * driver. 597 * 598 * After QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_PAUSE event is received 599 * by userspace with QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES 600 * flag not set, the next first 601 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO event from the driver 602 * shall be considered as un-pause event. 603 * 604 * All the attributes used with this command are defined in 605 * enum qca_wlan_vendor_attr_beacon_reporting_params. 606 * @QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP: In practice, some APs have 607 * interop issues with the DUT. This sub command is used to transfer the 608 * AP info between the driver and user space. This works both as a command 609 * and an event. As a command, it configures the stored list of APs from 610 * user space to firmware; as an event, it indicates the AP info detected 611 * by the firmware to user space for persistent storage. The attributes 612 * defined in enum qca_vendor_attr_interop_issues_ap are used to deliver 613 * the parameters. 614 * @QCA_NL80211_VENDOR_SUBCMD_OEM_DATA: This command/event is used to 615 * send/receive OEM data binary blobs to/from application/service to/from 616 * firmware. The attributes defined in enum 617 * qca_wlan_vendor_attr_oem_data_params are used to deliver the 618 * parameters. 619 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT: This command/event is used 620 * to send/receive avoid frequency data using 621 * enum qca_wlan_vendor_attr_avoid_frequency_ext. 622 * This new command is alternative to existing command 623 * QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY since existing command/event 624 * is using stream of bytes instead of structured data using vendor 625 * attributes. User space sends unsafe frequency ranges to the driver using 626 * a nested attribute %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE. On 627 * reception of this command, the driver shall check if an interface is 628 * operating on an unsafe frequency and the driver shall try to move to a 629 * safe channel when needed. If the driver is not able to find a safe 630 * channel the interface can keep operating on an unsafe channel with the 631 * TX power limit derived based on internal configurations like 632 * regulatory/SAR rules. 633 * 634 * @QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE: This vendor subcommand is used to 635 * add the STA node details in driver/firmware. Attributes for this event 636 * are specified in enum qca_wlan_vendor_attr_add_sta_node_params. 637 * @QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE: This command is used to set BT 638 * coex chain mode from application/service. 639 * The attributes defined in enum qca_vendor_attr_btc_chain_mode are used 640 * to deliver the parameters. 641 * 642 * @QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO: This vendor subcommand is used to 643 * get information of a station from driver to userspace. This command can 644 * be used in both STA and AP modes. For STA mode, it provides information 645 * of the current association when in connected state or the last 646 * association when in disconnected state. For AP mode, only information 647 * of the currently connected stations is available. This command uses 648 * attributes defined in enum qca_wlan_vendor_attr_get_sta_info. 649 * 650 * @QCA_NL80211_VENDOR_SUBCMD_REQUEST_SAR_LIMITS_EVENT: This acts as an event. 651 * Host drivers can request the user space entity to set the SAR power 652 * limits with this event. Accordingly, the user space entity is expected 653 * to set the SAR power limits. Host drivers can retry this event to the 654 * user space for the SAR power limits configuration from user space. If 655 * the driver does not get the SAR power limits from user space for all 656 * the retried attempts, it can configure a default SAR power limit. 657 * 658 * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO: This acts as a vendor event and 659 * is used to update the information about the station from the driver to 660 * userspace. Uses attributes from enum 661 * qca_wlan_vendor_attr_update_sta_info. 662 * 663 * @QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON: This acts as an event. 664 * The host driver initiates the disconnection for scenarios such as beacon 665 * miss, NUD failure, peer kick out, etc. The disconnection indication 666 * through cfg80211_disconnected() expects the reason codes from enum 667 * ieee80211_reasoncode which does not signify these various reasons why 668 * the driver has triggered the disconnection. This event will be used to 669 * send the driver specific reason codes by the host driver to userspace. 670 * Host drivers should trigger this event and pass the respective reason 671 * code immediately prior to triggering cfg80211_disconnected(). The 672 * attributes used with this event are defined in enum 673 * qca_wlan_vendor_attr_driver_disconnect_reason. 674 * 675 * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC: This vendor subcommand is used to 676 * add/delete TSPEC for each AC. One command is for one specific AC only. 677 * This command can only be used in STA mode and the STA must be 678 * associated with an AP when the command is issued. Uses attributes 679 * defined in enum qca_wlan_vendor_attr_config_tspec. 680 * 681 * @QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT: Vendor subcommand to configure TWT. 682 * Uses attributes defined in enum qca_wlan_vendor_attr_config_twt. 683 * 684 * @QCA_NL80211_VENDOR_SUBCMD_GETBAND: Command to get the enabled band(s) from 685 * the driver. The band configurations obtained are referred through 686 * QCA_WLAN_VENDOR_ATTR_SETBAND_MASK. 687 * 688 * @QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS: Vendor subcommand/event for medium 689 * assessment. 690 * Uses attributes defined in enum qca_wlan_vendor_attr_medium_assess. 691 * 692 * @QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID: This acts as a vendor event and is 693 * used to update SSID information in hostapd when it is updated in the 694 * driver. Uses the attribute NL80211_ATTR_SSID. 695 * 696 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS: This vendor subcommand is used by 697 * the driver to send opaque data from the firmware to userspace. The 698 * driver sends an event to userspace whenever such data is received from 699 * the firmware. 700 * 701 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA is used as the attribute to 702 * send this opaque data for this event. 703 * 704 * The format of the opaque data is specific to the particular firmware 705 * version and there is no guarantee of the format remaining same. 706 * 707 * @QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS: This acts as an event. 708 * The host driver selects Tx VDEV, and notifies user. The attributes 709 * used with this event are defined in enum 710 * qca_wlan_vendor_attr_mbssid_tx_vdev_status. 711 * This event contains Tx VDEV group information, other VDEVs 712 * interface index, and status information. 713 * 714 * @QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY: Vendor command to 715 * configure the concurrent session policies when multiple STA interfaces 716 * are (getting) active. The attributes used by this command are defined 717 * in enum qca_wlan_vendor_attr_concurrent_sta_policy. 718 * 719 * @QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS: Userspace can use this command 720 * to query usable channels for different interface types such as STA, 721 * AP, P2P GO, P2P Client, NAN, etc. The driver shall report all usable 722 * channels in the response based on country code, different static 723 * configurations, concurrency combinations, etc. The attributes used 724 * with this command are defined in 725 * enum qca_wlan_vendor_attr_usable_channels. 726 * 727 * @QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY: This vendor subcommand is used 728 * to get DFS radar history from the driver to userspace. The driver 729 * returns QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES attribute with an 730 * array of nested entries. 731 * 732 * @QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD: Userspace can use this command to 733 * enable/disable mDNS offload to the firmware. The attributes used with 734 * this command are defined in enum qca_wlan_vendor_attr_mdns_offload. 735 * 736 * @QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE: This vendor subcommand is used 737 * to set packet monitor mode that aims to send the specified set of TX and 738 * RX frames on the current client interface to an active monitor 739 * interface. If this monitor mode is set, the driver will send the 740 * configured frames, from the interface on which the command is issued, to 741 * an active monitor interface. The attributes used with this command are 742 * defined in enum qca_wlan_vendor_attr_set_monitor_mode. 743 * 744 * Though the monitor mode is configured for the respective 745 * Data/Management/Control frames, it is up to the respective WLAN 746 * driver/firmware/hardware designs to consider the possibility of sending 747 * these frames over the monitor interface. For example, the Control frames 748 * are handled within the hardware and thus passing such frames over the 749 * monitor interface is left to the respective designs. 750 * 751 * Also, this monitor mode is governed to behave accordingly in 752 * suspend/resume states. If the firmware handles any of such frames in 753 * suspend state without waking up the host and if the monitor mode is 754 * configured to notify all such frames, the firmware is expected to resume 755 * the host and forward the respective frames to the monitor interface. 756 * Please note that such a request to get the frames over the monitor 757 * interface will have a definite power implication. 758 * 759 * @QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS: This vendor subcommand is used both 760 * as a request to set the driver/firmware with the parameters to trigger 761 * the roaming events, and also used by the driver/firmware to pass on the 762 * various roam events to userspace. 763 * Applicable only for the STA mode. The attributes used with this command 764 * are defined in enum qca_wlan_vendor_attr_roam_events. 765 */ 766 enum qca_nl80211_vendor_subcmds { 767 QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, 768 QCA_NL80211_VENDOR_SUBCMD_TEST = 1, 769 /* subcmds 2..8 not yet allocated */ 770 QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, 771 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, 772 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, 773 QCA_NL80211_VENDOR_SUBCMD_NAN = 12, 774 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, 775 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, 776 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, 777 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, 778 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, 779 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, 780 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, 781 QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20, 782 QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21, 783 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22, 784 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23, 785 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24, 786 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25, 787 QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26, 788 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27, 789 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28, 790 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29, 791 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30, 792 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31, 793 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32, 794 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33, 795 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, 796 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, 797 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, 798 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, 799 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, 800 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, 801 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, 802 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41, 803 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, 804 /* 43..49 - reserved for QCA */ 805 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, 806 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, 807 QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, 808 /* 53 - reserved - was used by QCA, but not in use anymore */ 809 QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, 810 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, 811 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, 812 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, 813 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, 814 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, 815 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, 816 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, 817 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, 818 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, 819 QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, 820 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65, 821 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66, 822 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67, 823 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68, 824 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69, 825 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70, 826 QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71, 827 QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72, 828 QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73, 829 /* Wi-Fi configuration subcommands */ 830 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, 831 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, 832 QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, 833 QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, 834 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, 835 QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, 836 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, 837 QCA_NL80211_VENDOR_SUBCMD_NDP = 81, 838 QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, 839 QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, 840 QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, 841 QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, 842 /* 86-90 - reserved for QCA */ 843 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, 844 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, 845 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, 846 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, 847 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, 848 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, 849 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, 850 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, 851 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, 852 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, 853 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, 854 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, 855 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, 856 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, 857 QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, 858 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, 859 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, 860 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, 861 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, 862 /* 110..114 - reserved for QCA */ 863 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115, 864 QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY = 116, 865 /* 117 - reserved for QCA */ 866 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, 867 QCA_NL80211_VENDOR_SUBCMD_TSF = 119, 868 QCA_NL80211_VENDOR_SUBCMD_WISA = 120, 869 /* 121 - reserved for QCA */ 870 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, 871 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, 872 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, 873 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, 874 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, 875 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, 876 /* FTM/indoor location subcommands */ 877 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, 878 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, 879 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, 880 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, 881 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, 882 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, 883 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, 884 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, 885 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, 886 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, 887 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, 888 /* DMG low level RF sector operations */ 889 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, 890 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, 891 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, 892 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, 893 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, 894 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, 895 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, 896 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, 897 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, 898 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, 899 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, 900 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, 901 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, 902 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, 903 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, 904 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, 905 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, 906 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, 907 QCA_NL80211_VENDOR_SUBCMD_HANG = 157, 908 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, 909 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, 910 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, 911 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, 912 /* Flush peer pending data */ 913 QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162, 914 QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, 915 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, 916 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, 917 QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, 918 /* Thermal shutdown commands to protect wifi chip */ 919 QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167, 920 QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168, 921 /* Wi-Fi test configuration subcommand */ 922 QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, 923 /* Frame filter operations for other BSSs/unassociated STAs */ 924 QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170, 925 QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, 926 QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT = 172, 927 QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173, 928 QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, 929 QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175, 930 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS = 176, 931 QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, 932 QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178, 933 QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179, 934 QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING = 180, 935 QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP = 181, 936 QCA_NL80211_VENDOR_SUBCMD_OEM_DATA = 182, 937 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT = 183, 938 QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE = 184, 939 QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE = 185, 940 QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO = 186, 941 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS_EVENT = 187, 942 QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO = 188, 943 QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON = 189, 944 QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC = 190, 945 QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT = 191, 946 QCA_NL80211_VENDOR_SUBCMD_GETBAND = 192, 947 QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS = 193, 948 QCA_NL80211_VENDOR_SUBCMD_UPDATE_SSID = 194, 949 QCA_NL80211_VENDOR_SUBCMD_WIFI_FW_STATS = 195, 950 QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS = 196, 951 QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY = 197, 952 QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS = 198, 953 QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY = 199, 954 QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD = 200, 955 /* 201 - reserved for QCA */ 956 QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE = 202, 957 QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS = 203, 958 }; 959 960 enum qca_wlan_vendor_attr { 961 QCA_WLAN_VENDOR_ATTR_INVALID = 0, 962 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ 963 QCA_WLAN_VENDOR_ATTR_DFS = 1, 964 /* Used only when driver sends vendor events to the userspace under the 965 * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends 966 * commands to the driver. 967 */ 968 QCA_WLAN_VENDOR_ATTR_NAN = 2, 969 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 970 QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, 971 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 972 QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, 973 /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined 974 * by enum qca_roaming_policy. 975 */ 976 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, 977 QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, 978 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 979 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, 980 QCA_WLAN_VENDOR_ATTR_TEST = 8, 981 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 982 /* Unsigned 32-bit value. */ 983 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, 984 /* Unsigned 32-bit value */ 985 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, 986 /* Unsigned 32-bit value */ 987 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, 988 /* Unsigned 32-bit value from enum qca_set_band. The allowed values for 989 * this attribute are limited to QCA_SETBAND_AUTO, QCA_SETBAND_5G, and 990 * QCA_SETBAND_2G. This attribute is deprecated. Recommendation is to 991 * use QCA_WLAN_VENDOR_ATTR_SETBAND_MASK instead. 992 */ 993 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, 994 /* Dummy (NOP) attribute for 64 bit padding */ 995 QCA_WLAN_VENDOR_ATTR_PAD = 13, 996 /* Unique FTM session cookie (Unsigned 64 bit). Specified in 997 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in 998 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and 999 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. 1000 */ 1001 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, 1002 /* Indoor location capabilities, returned by 1003 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. 1004 * see enum qca_wlan_vendor_attr_loc_capa. 1005 */ 1006 QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, 1007 /* Array of nested attributes containing information about each peer 1008 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info 1009 * for supported attributes for each peer. 1010 */ 1011 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, 1012 /* Array of nested attributes containing measurement results for 1013 * one or more peers, reported by the 1014 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. 1015 * See enum qca_wlan_vendor_attr_peer_result for list of supported 1016 * attributes. 1017 */ 1018 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, 1019 /* Flag attribute for enabling or disabling responder functionality. */ 1020 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, 1021 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 1022 * command to specify the LCI report that will be sent by 1023 * the responder during a measurement exchange. The format is 1024 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. 1025 */ 1026 QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, 1027 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 1028 * command to specify the location civic report that will 1029 * be sent by the responder during a measurement exchange. 1030 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. 1031 */ 1032 QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, 1033 /* Session/measurement completion status code, 1034 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and 1035 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT 1036 * see enum qca_vendor_attr_loc_session_status. 1037 */ 1038 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, 1039 /* Initial dialog token used by responder (0 if not specified), 1040 * unsigned 8 bit value. 1041 */ 1042 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, 1043 /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS 1044 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if 1045 * AOA measurements are needed as part of an FTM session. 1046 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See 1047 * enum qca_wlan_vendor_attr_aoa_type. 1048 */ 1049 QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, 1050 /* A bit mask (unsigned 32 bit value) of antenna arrays used 1051 * by indoor location measurements. Refers to the antenna 1052 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. 1053 */ 1054 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, 1055 /* AOA measurement data. Its contents depends on the AOA measurement 1056 * type and antenna array mask: 1057 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, 1058 * phase of the strongest CIR path for each antenna in the measured 1059 * array(s). 1060 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 1061 * values, phase and amplitude of the strongest CIR path for each 1062 * antenna in the measured array(s). 1063 */ 1064 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, 1065 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1066 * to specify the chain number (unsigned 32 bit value) to inquire 1067 * the corresponding antenna RSSI value 1068 */ 1069 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, 1070 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1071 * to report the specific antenna RSSI value (unsigned 32 bit value) 1072 */ 1073 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, 1074 /* Frequency in MHz, various uses. Unsigned 32 bit value */ 1075 QCA_WLAN_VENDOR_ATTR_FREQ = 28, 1076 /* TSF timer value, unsigned 64 bit value. 1077 * May be returned by various commands. 1078 */ 1079 QCA_WLAN_VENDOR_ATTR_TSF = 29, 1080 /* DMG RF sector index, unsigned 16 bit number. Valid values are 1081 * 0..127 for sector indices or 65535 as special value used to 1082 * unlock sector selection in 1083 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. 1084 */ 1085 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, 1086 /* DMG RF sector type, unsigned 8 bit value. One of the values 1087 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. 1088 */ 1089 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, 1090 /* Bitmask of DMG RF modules for which information is requested. Each 1091 * bit corresponds to an RF module with the same index as the bit 1092 * number. Unsigned 32 bit number but only low 8 bits can be set since 1093 * all DMG chips currently have up to 8 RF modules. 1094 */ 1095 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, 1096 /* Array of nested attributes where each entry is DMG RF sector 1097 * configuration for a single RF module. 1098 * Attributes for each entry are taken from enum 1099 * qca_wlan_vendor_attr_dmg_rf_sector_cfg. 1100 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG 1101 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. 1102 */ 1103 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, 1104 /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command 1105 * to report frame aggregation statistics to userspace. 1106 */ 1107 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, 1108 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, 1109 /* Unsigned 8-bit value representing MBO transition reason code as 1110 * provided by the AP used by subcommand 1111 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is 1112 * specified by the userspace in the request to the driver. 1113 */ 1114 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, 1115 /* Array of nested attributes, BSSID and status code, used by subcommand 1116 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each 1117 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. 1118 * The userspace space specifies the list/array of candidate BSSIDs in 1119 * the order of preference in the request. The driver specifies the 1120 * status code, for each BSSID in the list, in the response. The 1121 * acceptable candidates are listed in the order preferred by the 1122 * driver. 1123 */ 1124 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, 1125 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 1126 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. 1127 */ 1128 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, 1129 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 1130 * to define the number of antennas to use for BRP. 1131 * different purpose in each ANT_LIMIT_MODE: 1132 * DISABLE - ignored 1133 * EFFECTIVE - upper limit to number of antennas to be used 1134 * FORCE - exact number of antennas to be used 1135 * unsigned 8 bit value 1136 */ 1137 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, 1138 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 1139 * to report the corresponding antenna index to the chain RSSI value 1140 */ 1141 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, 1142 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command to report 1143 * the specific antenna EVM value (unsigned 32 bit value). With a 1144 * determinate group of antennas, the driver specifies the EVM value 1145 * for each antenna ID, and application extract them in user space. 1146 */ 1147 QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, 1148 /* 1149 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report 1150 * wlan firmware current state. FW state is an unsigned 8 bit value, 1151 * one of the values in enum qca_wlan_vendor_attr_fw_state. 1152 */ 1153 QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, 1154 1155 /* Unsigned 32-bitmask value from enum qca_set_band. Substitutes the 1156 * attribute QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE for which only a subset 1157 * of single values from enum qca_set_band are valid. This attribute 1158 * uses bitmask combinations to define the respective allowed band 1159 * combinations and this attributes takes precedence over 1160 * QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE if both attributes are included. 1161 */ 1162 QCA_WLAN_VENDOR_ATTR_SETBAND_MASK = 43, 1163 1164 /* keep last */ 1165 QCA_WLAN_VENDOR_ATTR_AFTER_LAST, 1166 QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1, 1167 }; 1168 1169 enum qca_roaming_policy { 1170 QCA_ROAMING_NOT_ALLOWED, 1171 QCA_ROAMING_ALLOWED_WITHIN_ESS, 1172 }; 1173 1174 /** 1175 * enum qca_roam_reason - Represents the reason codes for roaming. Used by 1176 * QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON. 1177 * 1178 * @QCA_ROAM_REASON_UNKNOWN: Any reason that do not classify under the below 1179 * reasons. 1180 * 1181 * @QCA_ROAM_REASON_PER: Roam triggered when packet error rates (PER) breached 1182 * the configured threshold. 1183 * 1184 * @QCA_ROAM_REASON_BEACON_MISS: Roam triggered due to the continuous configured 1185 * beacon misses from the then connected AP. 1186 * 1187 * @QCA_ROAM_REASON_POOR_RSSI: Roam triggered due to the poor RSSI reported 1188 * by the connected AP. 1189 * 1190 * @QCA_ROAM_REASON_BETTER_RSSI: Roam triggered for finding a BSS with a better 1191 * RSSI than the connected BSS. Here the RSSI of the current BSS is not poor. 1192 * 1193 * @QCA_ROAM_REASON_CONGESTION: Roam triggered considering the connected channel 1194 * or environment being very noisy or congested. 1195 * 1196 * @QCA_ROAM_REASON_USER_TRIGGER: Roam triggered due to an explicit request 1197 * from the user (user space). 1198 * 1199 * @QCA_ROAM_REASON_BTM: Roam triggered due to BTM Request frame received from 1200 * the connected AP. 1201 * 1202 * @QCA_ROAM_REASON_BSS_LOAD: Roam triggered due to the channel utilization 1203 * breaching out the configured threshold. 1204 * 1205 * @QCA_ROAM_REASON_WTC: Roam triggered due to Wireless to Cellular BSS 1206 * transition request. 1207 * 1208 * @QCA_ROAM_REASON_IDLE: Roam triggered when device is suspended, there is no 1209 * data activity with the AP and the current RSSI falls below a certain 1210 * threshold. 1211 * 1212 * @QCA_ROAM_REASON_DISCONNECTION: Roam triggered due to Deauthentication or 1213 * Disassociation frames received from the connected AP. 1214 * 1215 * @QCA_ROAM_REASON_PERIODIC_TIMER: Roam triggered as part of the periodic scan 1216 * that happens when there is no candidate AP found during the poor RSSI scan 1217 * trigger. 1218 * 1219 * @QCA_ROAM_REASON_BACKGROUND_SCAN: Roam triggered based on the scan results 1220 * obtained from an external scan (not aimed at roaming). 1221 * 1222 * @QCA_ROAM_REASON_BT_ACTIVITY: Roam triggered due to Bluetooth connection is 1223 * established when the station is connected in the 2.4 GHz band. 1224 */ 1225 enum qca_roam_reason { 1226 QCA_ROAM_REASON_UNKNOWN, 1227 QCA_ROAM_REASON_PER, 1228 QCA_ROAM_REASON_BEACON_MISS, 1229 QCA_ROAM_REASON_POOR_RSSI, 1230 QCA_ROAM_REASON_BETTER_RSSI, 1231 QCA_ROAM_REASON_CONGESTION, 1232 QCA_ROAM_REASON_USER_TRIGGER, 1233 QCA_ROAM_REASON_BTM, 1234 QCA_ROAM_REASON_BSS_LOAD, 1235 QCA_ROAM_REASON_WTC, 1236 QCA_ROAM_REASON_IDLE, 1237 QCA_ROAM_REASON_DISCONNECTION, 1238 QCA_ROAM_REASON_PERIODIC_TIMER, 1239 QCA_ROAM_REASON_BACKGROUND_SCAN, 1240 QCA_ROAM_REASON_BT_ACTIVITY, 1241 }; 1242 1243 enum qca_wlan_vendor_attr_roam_auth { 1244 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, 1245 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, 1246 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, 1247 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, 1248 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, 1249 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, 1250 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, 1251 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, 1252 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, 1253 /* Indicates the status of re-association requested by user space for 1254 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. 1255 * Type u16. 1256 * Represents the status code from AP. Use 1257 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the 1258 * real status code for failures. 1259 */ 1260 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, 1261 /* This attribute indicates that the old association was maintained when 1262 * a re-association is requested by user space and that re-association 1263 * attempt fails (i.e., cannot connect to the requested BSS, but can 1264 * remain associated with the BSS with which the association was in 1265 * place when being requested to roam). Used along with 1266 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current 1267 * re-association status. Type flag. 1268 * This attribute is applicable only for re-association failure cases. 1269 */ 1270 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, 1271 /* This attribute specifies the PMK if one was newly generated during 1272 * FILS roaming. This is added to the PMKSA cache and is used in 1273 * subsequent connections with PMKSA caching. 1274 */ 1275 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11, 1276 /* This attribute specifies the PMKID used/generated for the current 1277 * FILS roam. This is used in subsequent connections with PMKSA caching. 1278 */ 1279 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12, 1280 /* A 16-bit unsigned value specifying the next sequence number to use 1281 * in ERP message in the currently associated realm. This is used in 1282 * doing subsequent ERP based connections in the same realm. 1283 */ 1284 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13, 1285 /* A 16-bit unsigned value representing the reasons for the roaming. 1286 * Defined by enum qca_roam_reason. 1287 */ 1288 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON = 14, 1289 1290 /* keep last */ 1291 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, 1292 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = 1293 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 1294 }; 1295 1296 enum qca_wlan_vendor_attr_p2p_listen_offload { 1297 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, 1298 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one 1299 * of the social channels. 1300 */ 1301 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, 1302 /* A 32-bit unsigned value; the P2P listen offload period (ms). 1303 */ 1304 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, 1305 /* A 32-bit unsigned value; the P2P listen interval duration (ms). 1306 */ 1307 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, 1308 /* A 32-bit unsigned value; number of interval times the firmware needs 1309 * to run the offloaded P2P listen operation before it stops. 1310 */ 1311 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, 1312 /* An array of arbitrary binary data with one or more 8-byte values. 1313 * The device types include both primary and secondary device types. 1314 */ 1315 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, 1316 /* An array of unsigned 8-bit characters; vendor information elements. 1317 */ 1318 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, 1319 /* A 32-bit unsigned value; a control flag to indicate whether listen 1320 * results need to be flushed to wpa_supplicant. 1321 */ 1322 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, 1323 /* A 8-bit unsigned value; reason code for P2P listen offload stop 1324 * event. 1325 */ 1326 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, 1327 /* keep last */ 1328 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, 1329 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = 1330 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 1331 }; 1332 1333 /** 1334 * enum qca_wlan_vendor_attr_acs_offload - Defines attributes to be used with 1335 * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. 1336 * 1337 * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL: Required (u8). 1338 * Used with event to notify the primary channel number selected in ACS 1339 * operation. 1340 * Note: If both the driver and user-space application supports the 6 GHz band, 1341 * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL is deprecated; use 1342 * QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY instead. 1343 * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL 1344 * is still used if either of the driver or user space application doesn't 1345 * support the 6 GHz band. 1346 * 1347 * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL: Required (u8). 1348 * Used with event to notify the secondary channel number selected in ACS 1349 * operation. 1350 * Note: If both the driver and user-space application supports the 6 GHz band, 1351 * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is deprecated; use 1352 * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY instead. 1353 * To maintain backward compatibility, 1354 * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL is still used if either of 1355 * the driver or user space application doesn't support 6 GHz band. 1356 * 1357 * @QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE: Required (u8). 1358 * (a) Used with command to configure hw_mode from 1359 * enum qca_wlan_vendor_acs_hw_mode for ACS operation. 1360 * (b) Also used with event to notify the hw_mode of selected primary channel 1361 * in ACS operation. 1362 * 1363 * @QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED: Flag attribute. 1364 * Used with command to configure ACS operation for HT mode. 1365 * Disable (flag attribute not present) - HT disabled and 1366 * Enable (flag attribute present) - HT enabled. 1367 * 1368 * @QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED: Flag attribute. 1369 * Used with command to configure ACS operation for HT40 mode. 1370 * Disable (flag attribute not present) - HT40 disabled and 1371 * Enable (flag attribute present) - HT40 enabled. 1372 * 1373 * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED: Flag attribute. 1374 * Used with command to configure ACS operation for VHT mode. 1375 * Disable (flag attribute not present) - VHT disabled and 1376 * Enable (flag attribute present) - VHT enabled. 1377 * 1378 * @QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH: Optional (u16) with command and 1379 * mandatory with event. 1380 * If specified in command path, ACS operation is configured with the given 1381 * channel width (in MHz). 1382 * In event path, specifies the channel width of the primary channel selected. 1383 * 1384 * @QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST: Required and type is NLA_UNSPEC. 1385 * Used with command to configure channel list using an array of 1386 * channel numbers (u8). 1387 * Note: If both the driver and user-space application supports the 6 GHz band, 1388 * the driver mandates use of QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST whereas 1389 * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST is optional. 1390 * 1391 * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL: Required (u8). 1392 * Used with event to notify the VHT segment 0 center channel number selected in 1393 * ACS operation. The value is the index of the channel center frequency for 1394 * 20 MHz, 40 MHz, and 80 MHz channels. The value is the center frequency index 1395 * of the primary 80 MHz segment for 160 MHz and 80+80 MHz channels. 1396 * Note: If both the driver and user-space application supports the 6 GHz band, 1397 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is deprecated; use 1398 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY instead. 1399 * To maintain backward compatibility, 1400 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL is still used if either of 1401 * the driver or user space application doesn't support the 6 GHz band. 1402 * 1403 * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL: Required (u8). 1404 * Used with event to notify the VHT segment 1 center channel number selected in 1405 * ACS operation. The value is zero for 20 MHz, 40 MHz, and 80 MHz channels. 1406 * The value is the index of the channel center frequency for 160 MHz channels 1407 * and the center frequency index of the secondary 80 MHz segment for 80+80 MHz 1408 * channels. 1409 * Note: If both the driver and user-space application supports the 6 GHz band, 1410 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is deprecated; use 1411 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY instead. 1412 * To maintain backward compatibility, 1413 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL is still used if either of 1414 * the driver or user space application doesn't support the 6 GHz band. 1415 * 1416 * @QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST: Required and type is NLA_UNSPEC. 1417 * Used with command to configure the channel list using an array of channel 1418 * center frequencies in MHz (u32). 1419 * Note: If both the driver and user-space application supports the 6 GHz band, 1420 * the driver first parses the frequency list and if it fails to get a frequency 1421 * list, parses the channel list specified using 1422 * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST (considers only 2 GHz and 5 GHz channels in 1423 * QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST). 1424 * 1425 * @QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY: Required (u32). 1426 * Used with event to notify the primary channel center frequency (MHz) selected 1427 * in ACS operation. 1428 * Note: If the driver supports the 6 GHz band, the event sent from the driver 1429 * includes this attribute along with QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL. 1430 * 1431 * @QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY: Required (u32). 1432 * Used with event to notify the secondary channel center frequency (MHz) 1433 * selected in ACS operation. 1434 * Note: If the driver supports the 6 GHz band, the event sent from the driver 1435 * includes this attribute along with 1436 * QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL. 1437 * 1438 * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY: Required (u32). 1439 * Used with event to notify the VHT segment 0 center channel frequency (MHz) 1440 * selected in ACS operation. 1441 * Note: If the driver supports the 6 GHz band, the event sent from the driver 1442 * includes this attribute along with 1443 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL. 1444 * 1445 * @QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY: Required (u32). 1446 * Used with event to notify the VHT segment 1 center channel frequency (MHz) 1447 * selected in ACS operation. 1448 * Note: If the driver supports the 6 GHz band, the event sent from the driver 1449 * includes this attribute along with 1450 * QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL. 1451 * 1452 * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED: Flag attribute. 1453 * Used with command to notify the driver of EDMG request for ACS 1454 * operation. 1455 * 1456 * @QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL: Optional (u8). 1457 * Used with event to notify the EDMG channel number selected in ACS 1458 * operation. 1459 * EDMG primary channel is indicated by QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL 1460 * 1461 * @QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP: Optional (u16). 1462 * Used with event to notify the puncture pattern selected in ACS operation. 1463 * Encoding for this attribute will follow the convention used in the Disabled 1464 * Subchannel Bitmap field of the EHT Operation IE. 1465 * 1466 * @QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED: Flag attribute. 1467 * Used with command to configure ACS operation for EHT mode. 1468 * Disable (flag attribute not present) - EHT disabled and 1469 * Enable (flag attribute present) - EHT enabled. 1470 */ 1471 enum qca_wlan_vendor_attr_acs_offload { 1472 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, 1473 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL = 1, 1474 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL = 2, 1475 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE = 3, 1476 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED = 4, 1477 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED = 5, 1478 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED = 6, 1479 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH = 7, 1480 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST = 8, 1481 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL = 9, 1482 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL = 10, 1483 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST = 11, 1484 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_FREQUENCY = 12, 1485 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_FREQUENCY = 13, 1486 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_FREQUENCY = 14, 1487 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_FREQUENCY = 15, 1488 QCA_WLAN_VENDOR_ATTR_ACS_EDMG_ENABLED = 16, 1489 QCA_WLAN_VENDOR_ATTR_ACS_EDMG_CHANNEL = 17, 1490 QCA_WLAN_VENDOR_ATTR_ACS_PUNCTURE_BITMAP = 18, 1491 QCA_WLAN_VENDOR_ATTR_ACS_EHT_ENABLED = 19, 1492 1493 /* keep last */ 1494 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, 1495 QCA_WLAN_VENDOR_ATTR_ACS_MAX = 1496 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 1497 }; 1498 1499 /** 1500 * enum qca_wlan_vendor_acs_hw_mode - Defines HW mode to be used with the 1501 * vendor command/event QCA_NL80211_VENDOR_SUBCMD_DO_ACS. 1502 * 1503 * @QCA_ACS_MODE_IEEE80211B: 802.11b mode 1504 * @QCA_ACS_MODE_IEEE80211G: 802.11g mode 1505 * @QCA_ACS_MODE_IEEE80211A: 802.11a mode 1506 * @QCA_ACS_MODE_IEEE80211AD: 802.11ad mode 1507 * @QCA_ACS_MODE_IEEE80211ANY: all modes 1508 * @QCA_ACS_MODE_IEEE80211AX: 802.11ax mode 1509 */ 1510 enum qca_wlan_vendor_acs_hw_mode { 1511 QCA_ACS_MODE_IEEE80211B, 1512 QCA_ACS_MODE_IEEE80211G, 1513 QCA_ACS_MODE_IEEE80211A, 1514 QCA_ACS_MODE_IEEE80211AD, 1515 QCA_ACS_MODE_IEEE80211ANY, 1516 QCA_ACS_MODE_IEEE80211AX, 1517 }; 1518 1519 /** 1520 * enum qca_wlan_vendor_features - Vendor device/driver feature flags 1521 * 1522 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key 1523 * management offload, a mechanism where the station's firmware 1524 * does the exchange with the AP to establish the temporal keys 1525 * after roaming, rather than having the user space wpa_supplicant do it. 1526 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic 1527 * band selection based on channel selection results. 1528 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports 1529 * simultaneous off-channel operations. 1530 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P 1531 * Listen offload; a mechanism where the station's firmware takes care of 1532 * responding to incoming Probe Request frames received from other P2P 1533 * Devices whilst in Listen state, rather than having the user space 1534 * wpa_supplicant do it. Information from received P2P requests are 1535 * forwarded from firmware to host whenever the host processor wakes up. 1536 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA 1537 * specific features. 1538 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific 1539 * features. 1540 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON 1541 * specific features only. If a Device sets this bit but not the 1542 * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that 1543 * this Device may not support all OCE AP functionalities but can support 1544 * only OCE STA-CFON functionalities. 1545 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self 1546 * managed regulatory. 1547 * @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time). 1548 * @QCA_WLAN_VENDOR_FEATURE_11AX: Device supports 802.11ax (HE) 1549 * @QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT: Device supports 6 GHz band operation 1550 * @QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG: Device is capable of receiving 1551 * and applying thermal configuration through 1552 * %QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL and 1553 * %QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW attributes from 1554 * userspace. 1555 * @QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R: Device supports Adaptive 11r. 1556 * With Adaptive 11r feature, access points advertise the vendor 1557 * specific IEs and MDE but do not include FT AKM in the RSNE. 1558 * The Adaptive 11r supported stations are expected to identify 1559 * such vendor specific IEs and connect to the AP in FT mode though 1560 * the profile is configured in non-FT mode. 1561 * The driver-based SME cases also need to have this support for 1562 * Adaptive 11r to handle the connection and roaming scenarios. 1563 * This flag indicates the support for the same to the user space. 1564 * @QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS: Device supports 1565 * concurrent network sessions on different Wi-Fi bands. This feature 1566 * capability is attributed to the hardware's capability to support 1567 * the same (e.g., DBS). 1568 * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT: Flag indicating whether the 1569 * responses for the respective TWT operations are asynchronous (separate 1570 * event message) from the driver. If not specified, the responses are 1571 * synchronous (in vendor command reply) to the request. Each TWT 1572 * operation is specifically mentioned (against its respective 1573 * documentation) to support either of these or both modes. 1574 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits 1575 */ 1576 enum qca_wlan_vendor_features { 1577 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, 1578 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, 1579 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, 1580 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, 1581 QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, 1582 QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, 1583 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, 1584 QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, 1585 QCA_WLAN_VENDOR_FEATURE_TWT = 8, 1586 QCA_WLAN_VENDOR_FEATURE_11AX = 9, 1587 QCA_WLAN_VENDOR_FEATURE_6GHZ_SUPPORT = 10, 1588 QCA_WLAN_VENDOR_FEATURE_THERMAL_CONFIG = 11, 1589 QCA_WLAN_VENDOR_FEATURE_ADAPTIVE_11R = 12, 1590 QCA_WLAN_VENDOR_FEATURE_CONCURRENT_BAND_SESSIONS = 13, 1591 QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT = 14, 1592 NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ 1593 }; 1594 1595 /** 1596 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication 1597 * 1598 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to 1599 * the offloaded data. 1600 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded 1601 * data. 1602 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload 1603 * indication. 1604 */ 1605 enum qca_wlan_vendor_attr_data_offload_ind { 1606 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, 1607 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, 1608 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, 1609 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, 1610 1611 /* keep last */ 1612 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, 1613 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = 1614 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 1615 }; 1616 1617 /** 1618 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set 1619 * OCB config 1620 * 1621 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the 1622 * configuration 1623 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule 1624 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels 1625 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be 1626 * scheduled 1627 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel 1628 * information 1629 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL 1630 * active state configuration 1631 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as 1632 * OCB_CONFIG_FLAG_80211_FRAME_MODE 1633 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to 1634 * use in the case that a packet is sent without a TX control header 1635 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the 1636 * last TA received that the local time set by TA is synchronous to other 1637 * communicating OCB STAs. 1638 */ 1639 enum qca_wlan_vendor_attr_ocb_set_config { 1640 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0, 1641 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1, 1642 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2, 1643 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3, 1644 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4, 1645 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5, 1646 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6, 1647 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7, 1648 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8, 1649 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9, 1650 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST, 1651 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX = 1652 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1 1653 }; 1654 1655 /** 1656 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set 1657 * UTC time 1658 * 1659 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of 1660 * 10 bytes 1661 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of 1662 * 5 bytes 1663 */ 1664 enum qca_wlan_vendor_attr_ocb_set_utc_time { 1665 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0, 1666 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1, 1667 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2, 1668 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST, 1669 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX = 1670 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1 1671 }; 1672 1673 /** 1674 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes 1675 * to start sending timing advert frames 1676 * 1677 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency 1678 * on which to send the frames 1679 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times 1680 * the frame is sent in 5 seconds 1681 */ 1682 enum qca_wlan_vendor_attr_ocb_start_timing_advert { 1683 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0, 1684 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1, 1685 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2, 1686 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST, 1687 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX = 1688 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1 1689 }; 1690 1691 /** 1692 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes 1693 * to stop timing advert 1694 * 1695 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel 1696 * frequency on which to stop the timing advert 1697 */ 1698 enum qca_wlan_vendor_attr_ocb_stop_timing_advert { 1699 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0, 1700 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1, 1701 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST, 1702 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX = 1703 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1 1704 }; 1705 1706 /** 1707 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to 1708 * get TSF timer value 1709 * 1710 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the 1711 * timer 1712 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer 1713 */ 1714 enum qca_wlan_vendor_attr_ocb_get_tsf_resp { 1715 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0, 1716 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1, 1717 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2, 1718 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST, 1719 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX = 1720 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1 1721 }; 1722 1723 enum qca_vendor_attr_get_preferred_freq_list { 1724 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, 1725 /* A 32-unsigned value; the interface type/mode for which the preferred 1726 * frequency list is requested (see enum qca_iface_type for possible 1727 * values); used in GET_PREFERRED_FREQ_LIST command from user-space to 1728 * kernel and in the kernel response back to user-space. 1729 */ 1730 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, 1731 /* An array of 32-unsigned values; values are frequency (MHz); sent 1732 * from kernel space to user space. 1733 */ 1734 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, 1735 /* An array of nested values as per enum qca_wlan_vendor_attr_pcl 1736 * attribute. Each element contains frequency (MHz), weight, and flag 1737 * bit mask indicating how the frequency should be used in P2P 1738 * negotiation; sent from kernel space to user space. 1739 */ 1740 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL, 1741 /* keep last */ 1742 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, 1743 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = 1744 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 1745 }; 1746 1747 enum qca_vendor_attr_probable_oper_channel { 1748 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, 1749 /* 32-bit unsigned value; indicates the connection/iface type likely to 1750 * come on this channel (see enum qca_iface_type). 1751 */ 1752 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, 1753 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ 1754 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, 1755 /* keep last */ 1756 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, 1757 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = 1758 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 1759 }; 1760 1761 enum qca_iface_type { 1762 QCA_IFACE_TYPE_STA, 1763 QCA_IFACE_TYPE_AP, 1764 QCA_IFACE_TYPE_P2P_CLIENT, 1765 QCA_IFACE_TYPE_P2P_GO, 1766 QCA_IFACE_TYPE_IBSS, 1767 QCA_IFACE_TYPE_TDLS, 1768 }; 1769 1770 enum qca_set_band { 1771 QCA_SETBAND_AUTO = 0, 1772 QCA_SETBAND_5G = BIT(0), 1773 QCA_SETBAND_2G = BIT(1), 1774 QCA_SETBAND_6G = BIT(2), 1775 }; 1776 1777 /** 1778 * enum qca_access_policy - Access control policy 1779 * 1780 * Access control policy is applied on the configured IE 1781 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). 1782 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. 1783 * 1784 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match 1785 * the specific configuration (IE) set, i.e., allow all the 1786 * connections which do not match the configuration. 1787 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match 1788 * the specific configuration (IE) set, i.e., deny all the 1789 * connections which do not match the configuration. 1790 */ 1791 enum qca_access_policy { 1792 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, 1793 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, 1794 }; 1795 1796 /** 1797 * enum qca_vendor_attr_tsf_cmd: Vendor attributes for TSF capture 1798 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: Required (u32) 1799 * Specify the TSF command. Possible values are defined in 1800 * &enum qca_tsf_cmd. 1801 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Optional (u64) 1802 * This attribute contains TSF timer value. This attribute is only available 1803 * in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. 1804 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Optional (u64) 1805 * This attribute contains SOC timer value at TSF capture. This attribute is 1806 * only available in %QCA_TSF_GET or %QCA_TSF_SYNC_GET response. 1807 * @QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL: Optional (u32) 1808 * This attribute is used to provide TSF sync interval and only applicable when 1809 * TSF command is %QCA_TSF_SYNC_START. If this attribute is not provided, the 1810 * driver will use the default value. Time unit is in milliseconds. 1811 */ 1812 enum qca_vendor_attr_tsf_cmd { 1813 QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, 1814 QCA_WLAN_VENDOR_ATTR_TSF_CMD, 1815 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, 1816 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, 1817 QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL, 1818 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, 1819 QCA_WLAN_VENDOR_ATTR_TSF_MAX = 1820 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 1821 }; 1822 1823 /** 1824 * enum qca_tsf_cmd: TSF driver commands 1825 * @QCA_TSF_CAPTURE: Initiate TSF Capture 1826 * @QCA_TSF_GET: Get TSF capture value 1827 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value 1828 * @QCA_TSF_AUTO_REPORT_ENABLE: Used in STA mode only. Once set, the target 1829 * will automatically send TSF report to the host. To query 1830 * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY, this operation needs to be 1831 * initiated first. 1832 * @QCA_TSF_AUTO_REPORT_DISABLE: Used in STA mode only. Once set, the target 1833 * will not automatically send TSF report to the host. If 1834 * %QCA_TSF_AUTO_REPORT_ENABLE is initiated and 1835 * %QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY is not queried anymore, this 1836 * operation needs to be initiated. 1837 * @QCA_TSF_SYNC_START: Start periodic TSF sync feature. The driver periodically 1838 * fetches TSF and host time mapping from the firmware with interval configured 1839 * through the %QCA_WLAN_VENDOR_ATTR_TSF_SYNC_INTERVAL attribute. If the 1840 * interval value is not provided the driver will use the default value. The 1841 * userspace can query the TSF and host time mapping via the %QCA_TSF_GET 1842 * command. 1843 * @QCA_TSF_SYNC_STOP: Stop periodic TSF sync feature. 1844 */ 1845 enum qca_tsf_cmd { 1846 QCA_TSF_CAPTURE, 1847 QCA_TSF_GET, 1848 QCA_TSF_SYNC_GET, 1849 QCA_TSF_AUTO_REPORT_ENABLE, 1850 QCA_TSF_AUTO_REPORT_DISABLE, 1851 QCA_TSF_SYNC_START, 1852 QCA_TSF_SYNC_STOP, 1853 }; 1854 1855 /** 1856 * enum qca_vendor_attr_wisa_cmd 1857 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32) 1858 * WISA setup vendor commands 1859 */ 1860 enum qca_vendor_attr_wisa_cmd { 1861 QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, 1862 QCA_WLAN_VENDOR_ATTR_WISA_MODE, 1863 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, 1864 QCA_WLAN_VENDOR_ATTR_WISA_MAX = 1865 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 1866 }; 1867 1868 /* IEEE 802.11 Vendor Specific elements */ 1869 1870 /** 1871 * enum qca_vendor_element_id - QCA Vendor Specific element types 1872 * 1873 * These values are used to identify QCA Vendor Specific elements. The 1874 * payload of the element starts with the three octet OUI (OUI_QCA) and 1875 * is followed by a single octet type which is defined by this enum. 1876 * 1877 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. 1878 * This element can be used to specify preference order for supported 1879 * channels. The channels in this list are in preference order (the first 1880 * one has the highest preference) and are described as a pair of 1881 * (global) Operating Class and Channel Number (each one octet) fields. 1882 * 1883 * This extends the standard P2P functionality by providing option to have 1884 * more than one preferred operating channel. When this element is present, 1885 * it replaces the preference indicated in the Operating Channel attribute. 1886 * For supporting other implementations, the Operating Channel attribute is 1887 * expected to be used with the highest preference channel. Similarly, all 1888 * the channels included in this Preferred channel list element are 1889 * expected to be included in the Channel List attribute. 1890 * 1891 * This vendor element may be included in GO Negotiation Request, P2P 1892 * Invitation Request, and Provision Discovery Request frames. 1893 * 1894 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. 1895 * This element can be used for pre-standard publication testing of HE 1896 * before P802.11ax draft assigns the element ID. The payload of this 1897 * vendor specific element is defined by the latest P802.11ax draft. 1898 * Please note that the draft is still work in progress and this element 1899 * payload is subject to change. 1900 * 1901 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. 1902 * This element can be used for pre-standard publication testing of HE 1903 * before P802.11ax draft assigns the element ID. The payload of this 1904 * vendor specific element is defined by the latest P802.11ax draft. 1905 * Please note that the draft is still work in progress and this element 1906 * payload is subject to change. 1907 * 1908 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set 1909 * element). 1910 * This element can be used for pre-standard publication testing of HE 1911 * before P802.11ax draft assigns the element ID extension. The payload of 1912 * this vendor specific element is defined by the latest P802.11ax draft 1913 * (not including the Element ID Extension field). Please note that the 1914 * draft is still work in progress and this element payload is subject to 1915 * change. 1916 * 1917 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. 1918 * This element can be used for pre-standard publication testing of HE 1919 * before P802.11ax draft assigns the element ID extension. The payload of 1920 * this vendor specific element is defined by the latest P802.11ax draft 1921 * (not including the Element ID Extension field). Please note that the 1922 * draft is still work in progress and this element payload is subject to 1923 * change. 1924 * 1925 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. 1926 * This element can be used for pre-standard publication testing of HE 1927 * before P802.11ax draft assigns the element ID extension. The payload of 1928 * this vendor specific element is defined by the latest P802.11ax draft 1929 * (not including the Element ID Extension field). Please note that the 1930 * draft is still work in progress and this element payload is subject to 1931 * change. 1932 * 1933 * @QCA_VENDOR_ELEM_ALLPLAY: Allplay element 1934 */ 1935 enum qca_vendor_element_id { 1936 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, 1937 QCA_VENDOR_ELEM_HE_CAPAB = 1, 1938 QCA_VENDOR_ELEM_HE_OPER = 2, 1939 QCA_VENDOR_ELEM_RAPS = 3, 1940 QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, 1941 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, 1942 QCA_VENDOR_ELEM_ALLPLAY = 6, 1943 }; 1944 1945 /** 1946 * enum qca_wlan_vendor_scan_priority - Specifies the valid values that the 1947 * vendor scan attribute QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY can take. 1948 * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW: Very low priority 1949 * @QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW: Low priority 1950 * @QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM: Medium priority 1951 * @QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH: High priority 1952 * @QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH: Very high priority 1953 */ 1954 enum qca_wlan_vendor_scan_priority { 1955 QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_LOW = 0, 1956 QCA_WLAN_VENDOR_SCAN_PRIORITY_LOW = 1, 1957 QCA_WLAN_VENDOR_SCAN_PRIORITY_MEDIUM = 2, 1958 QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH = 3, 1959 QCA_WLAN_VENDOR_SCAN_PRIORITY_VERY_HIGH = 4, 1960 }; 1961 1962 /** 1963 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes 1964 * 1965 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan 1966 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes 1967 * with frequencies to be scanned (in MHz) 1968 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned 1969 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported 1970 * rates to be included 1971 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests 1972 * at non CCK rate in 2GHz band 1973 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags 1974 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the 1975 * driver for the specific scan request 1976 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan 1977 * request decoded as in enum scan_status 1978 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation 1979 * scan flag is set 1980 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with 1981 * randomisation 1982 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the 1983 * specific BSSID to scan for. 1984 * @QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME: Unsigned 64-bit dwell time in 1985 * microseconds. This is a common value which applies across all 1986 * frequencies specified by QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES. 1987 * @QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY: Priority of vendor scan relative to 1988 * other scan requests. It is a u32 attribute and takes values from enum 1989 * qca_wlan_vendor_scan_priority. This is an optional attribute. 1990 * If this attribute is not configured, the driver shall use 1991 * QCA_WLAN_VENDOR_SCAN_PRIORITY_HIGH as the priority of vendor scan. 1992 */ 1993 enum qca_wlan_vendor_attr_scan { 1994 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, 1995 QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, 1996 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, 1997 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, 1998 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, 1999 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, 2000 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, 2001 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, 2002 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, 2003 QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, 2004 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, 2005 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, 2006 QCA_WLAN_VENDOR_ATTR_SCAN_DWELL_TIME = 12, 2007 QCA_WLAN_VENDOR_ATTR_SCAN_PRIORITY = 13, 2008 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, 2009 QCA_WLAN_VENDOR_ATTR_SCAN_MAX = 2010 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 2011 }; 2012 2013 /** 2014 * enum scan_status - Specifies the valid values the vendor scan attribute 2015 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take 2016 * 2017 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with 2018 * new scan results 2019 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between 2020 */ 2021 enum scan_status { 2022 VENDOR_SCAN_STATUS_NEW_RESULTS, 2023 VENDOR_SCAN_STATUS_ABORTED, 2024 VENDOR_SCAN_STATUS_MAX, 2025 }; 2026 2027 /** 2028 * enum qca_vendor_attr_ota_test - Specifies the values for vendor 2029 * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST 2030 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test 2031 */ 2032 enum qca_vendor_attr_ota_test { 2033 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, 2034 /* 8-bit unsigned value to indicate if OTA test is enabled */ 2035 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, 2036 /* keep last */ 2037 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, 2038 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = 2039 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 2040 }; 2041 2042 /** 2043 * enum qca_vendor_attr_txpower_scale - vendor sub commands index 2044 * 2045 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value 2046 */ 2047 enum qca_vendor_attr_txpower_scale { 2048 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, 2049 /* 8-bit unsigned value to indicate the scaling of tx power */ 2050 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, 2051 /* keep last */ 2052 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, 2053 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = 2054 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 2055 }; 2056 2057 /** 2058 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease 2059 * 2060 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. 2061 */ 2062 enum qca_vendor_attr_txpower_decr_db { 2063 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, 2064 /* 8-bit unsigned value to indicate the reduction of TX power in dB for 2065 * a virtual interface. 2066 */ 2067 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, 2068 /* keep last */ 2069 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, 2070 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = 2071 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 2072 }; 2073 2074 /* Attributes for data used by 2075 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and 2076 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. 2077 */ 2078 enum qca_wlan_vendor_attr_config { 2079 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, 2080 /* Unsigned 32-bit value to set the DTIM period. 2081 * Whether the wifi chipset wakes at every dtim beacon or a multiple of 2082 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 2083 * DTIM beacons. 2084 */ 2085 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, 2086 /* Unsigned 32-bit value to set the wifi_iface stats averaging factor 2087 * used to calculate statistics like average the TSF offset or average 2088 * number of frame leaked. 2089 * For instance, upon Beacon frame reception: 2090 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 2091 * For instance, when evaluating leaky APs: 2092 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 2093 */ 2094 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, 2095 /* Unsigned 32-bit value to configure guard time, i.e., when 2096 * implementing IEEE power management based on frame control PM bit, how 2097 * long the driver waits before shutting down the radio and after 2098 * receiving an ACK frame for a Data frame with PM bit set. 2099 */ 2100 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, 2101 /* Unsigned 32-bit value to change the FTM capability dynamically */ 2102 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, 2103 /* Unsigned 16-bit value to configure maximum TX rate dynamically */ 2104 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, 2105 /* Unsigned 32-bit value to configure the number of continuous 2106 * Beacon Miss which shall be used by the firmware to penalize 2107 * the RSSI. 2108 */ 2109 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, 2110 /* Unsigned 8-bit value to configure the channel avoidance indication 2111 * behavior. Firmware to send only one indication and ignore duplicate 2112 * indications when set to avoid multiple Apps wakeups. 2113 */ 2114 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, 2115 /* 8-bit unsigned value to configure the maximum TX MPDU for 2116 * aggregation. 2117 */ 2118 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, 2119 /* 8-bit unsigned value to configure the maximum RX MPDU for 2120 * aggregation. 2121 */ 2122 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, 2123 /* 8-bit unsigned value to configure the Non aggregrate/11g sw 2124 * retry threshold (0 disable, 31 max). 2125 */ 2126 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, 2127 /* 8-bit unsigned value to configure the aggregrate sw 2128 * retry threshold (0 disable, 31 max). 2129 */ 2130 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, 2131 /* 8-bit unsigned value to configure the MGMT frame 2132 * retry threshold (0 disable, 31 max). 2133 */ 2134 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, 2135 /* 8-bit unsigned value to configure the CTRL frame 2136 * retry threshold (0 disable, 31 max). 2137 */ 2138 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, 2139 /* 8-bit unsigned value to configure the propagation delay for 2140 * 2G/5G band (0~63, units in us) 2141 */ 2142 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, 2143 /* Unsigned 32-bit value to configure the number of unicast TX fail 2144 * packet count. The peer is disconnected once this threshold is 2145 * reached. 2146 */ 2147 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, 2148 /* Attribute used to set scan default IEs to the driver. 2149 * 2150 * These IEs can be used by scan operations that will be initiated by 2151 * the driver/firmware. 2152 * 2153 * For further scan requests coming to the driver, these IEs should be 2154 * merged with the IEs received along with scan request coming to the 2155 * driver. If a particular IE is present in the scan default IEs but not 2156 * present in the scan request, then that IE should be added to the IEs 2157 * sent in the Probe Request frames for that scan request. 2158 */ 2159 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, 2160 /* Unsigned 32-bit attribute for generic commands */ 2161 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, 2162 /* Unsigned 32-bit value attribute for generic commands */ 2163 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, 2164 /* Unsigned 32-bit data attribute for generic command response */ 2165 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, 2166 /* Unsigned 32-bit length attribute for 2167 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 2168 */ 2169 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, 2170 /* Unsigned 32-bit flags attribute for 2171 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 2172 */ 2173 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, 2174 /* Unsigned 32-bit, defining the access policy. 2175 * See enum qca_access_policy. Used with 2176 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. 2177 */ 2178 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, 2179 /* Sets the list of full set of IEs for which a specific access policy 2180 * has to be applied. Used along with 2181 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. 2182 * Zero length payload can be used to clear this access constraint. 2183 */ 2184 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, 2185 /* Unsigned 32-bit, specifies the interface index (netdev) for which the 2186 * corresponding configurations are applied. If the interface index is 2187 * not specified, the configurations are attributed to the respective 2188 * wiphy. 2189 */ 2190 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, 2191 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ 2192 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, 2193 /* 8-bit unsigned value to configure the driver and below layers to 2194 * ignore the assoc disallowed set by APs while connecting 2195 * 1-Ignore, 0-Don't ignore 2196 */ 2197 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, 2198 /* 32-bit unsigned value to trigger antenna diversity features: 2199 * 1-Enable, 0-Disable 2200 */ 2201 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, 2202 /* 32-bit unsigned value to configure specific chain antenna */ 2203 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, 2204 /* 32-bit unsigned value to trigger cycle selftest 2205 * 1-Enable, 0-Disable 2206 */ 2207 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, 2208 /* 32-bit unsigned to configure the cycle time of selftest 2209 * the unit is micro-second 2210 */ 2211 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, 2212 /* 32-bit unsigned value to set reorder timeout for AC_VO */ 2213 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, 2214 /* 32-bit unsigned value to set reorder timeout for AC_VI */ 2215 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, 2216 /* 32-bit unsigned value to set reorder timeout for AC_BE */ 2217 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, 2218 /* 32-bit unsigned value to set reorder timeout for AC_BK */ 2219 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, 2220 /* 6-byte MAC address to point out the specific peer */ 2221 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, 2222 /* 32-bit unsigned value to set window size for specific peer */ 2223 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, 2224 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ 2225 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, 2226 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ 2227 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, 2228 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for 2229 * station device while in disconnect state. The attribute use the 2230 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, 2231 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or 2232 * 10 MHz channel width, the station will not connect to a BSS using 20 2233 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to 2234 * clear this constraint. 2235 */ 2236 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, 2237 /* 32-bit unsigned value to configure the propagation absolute delay 2238 * for 2G/5G band (units in us) 2239 */ 2240 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, 2241 /* 32-bit unsigned value to set probe period */ 2242 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, 2243 /* 32-bit unsigned value to set stay period */ 2244 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, 2245 /* 32-bit unsigned value to set snr diff */ 2246 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, 2247 /* 32-bit unsigned value to set probe dwell time */ 2248 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, 2249 /* 32-bit unsigned value to set mgmt snr weight */ 2250 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, 2251 /* 32-bit unsigned value to set data snr weight */ 2252 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, 2253 /* 32-bit unsigned value to set ack snr weight */ 2254 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, 2255 /* 32-bit unsigned value to configure the listen interval. 2256 * This is in units of beacon intervals. This configuration alters 2257 * the negotiated listen interval with the AP during the connection. 2258 * It is highly recommended to configure a value less than or equal to 2259 * the one negotiated during the association. Configuring any greater 2260 * value can have adverse effects (frame loss, AP disassociating STA, 2261 * etc.). 2262 */ 2263 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, 2264 /* 2265 * 8 bit unsigned value that is set on an AP/GO virtual interface to 2266 * disable operations that would cause the AP/GO to leave its operating 2267 * channel. 2268 * 2269 * This will restrict the scans to the AP/GO operating channel and the 2270 * channels of the other band, if DBS is supported.A STA/CLI interface 2271 * brought up after this setting is enabled, will be restricted to 2272 * connecting to devices only on the AP/GO interface's operating channel 2273 * or on the other band in DBS case. P2P supported channel list is 2274 * modified, to only include AP interface's operating-channel and the 2275 * channels of the other band if DBS is supported. 2276 * 2277 * These restrictions are only applicable as long as the AP/GO interface 2278 * is alive. If the AP/GO interface is brought down then this 2279 * setting/restriction is forgotten. 2280 * 2281 * If this variable is set on an AP/GO interface while a multi-channel 2282 * concurrent session is active, it has no effect on the operation of 2283 * the current interfaces, other than restricting the scan to the AP/GO 2284 * operating channel and the other band channels if DBS is supported. 2285 * However, if the STA is brought down and restarted then the new STA 2286 * connection will either be formed on the AP/GO channel or on the 2287 * other band in a DBS case. This is because of the scan being 2288 * restricted on these channels as mentioned above. 2289 * 2290 * 1-Restrict / 0-Don't restrict offchannel operations. 2291 */ 2292 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, 2293 /* 2294 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) 2295 * on an interface. 2296 * 1 - Enable, 0 - Disable. 2297 */ 2298 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, 2299 2300 /* 2301 * 8 bit unsigned value to globally enable/disable scan 2302 * 1 - Enable, 0 - Disable. 2303 */ 2304 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, 2305 2306 /* 8-bit unsigned value to set the total beacon miss count 2307 * This parameter will set the total beacon miss count. 2308 */ 2309 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, 2310 2311 /* Unsigned 32-bit value to configure the number of continuous 2312 * Beacon Miss which shall be used by the firmware to penalize 2313 * the RSSI for BTC. 2314 */ 2315 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, 2316 2317 /* 8-bit unsigned value to configure the driver and below layers to 2318 * enable/disable all FILS features. 2319 * 0-enable, 1-disable 2320 */ 2321 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, 2322 2323 /* 16-bit unsigned value to configure the level of WLAN latency 2324 * module. See enum qca_wlan_vendor_attr_config_latency_level. 2325 */ 2326 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, 2327 2328 /* 8-bit unsigned value indicating the driver to use the RSNE as-is from 2329 * the connect interface. Exclusively used for the scenarios where the 2330 * device is used as a test bed device with special functionality and 2331 * not recommended for production. This helps driver to not validate the 2332 * RSNE passed from user space and thus allow arbitrary IE data to be 2333 * used for testing purposes. 2334 * 1-enable, 0-disable. 2335 * Applications set/reset this configuration. If not reset, this 2336 * parameter remains in use until the driver is unloaded. 2337 */ 2338 QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, 2339 2340 /* 8-bit unsigned value to trigger green Tx power saving. 2341 * 1-Enable, 0-Disable 2342 */ 2343 QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, 2344 2345 /* Attribute to configure disconnect IEs to the driver. 2346 * This carries an array of unsigned 8-bit characters. 2347 * 2348 * If this is configured, driver shall fill the IEs in disassoc/deauth 2349 * frame. 2350 * These IEs are expected to be considered only for the next 2351 * immediate disconnection (disassoc/deauth frame) originated by 2352 * the DUT, irrespective of the entity (user space/driver/firmware) 2353 * triggering the disconnection. 2354 * The host drivers are not expected to use the IEs set through 2355 * this interface for further disconnections after the first immediate 2356 * disconnection initiated post the configuration. 2357 * If the IEs are also updated through cfg80211 interface (after the 2358 * enhancement to cfg80211_disconnect), host driver is expected to 2359 * take the union of IEs from both of these interfaces and send in 2360 * further disassoc/deauth frames. 2361 */ 2362 QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES = 58, 2363 2364 /* 8-bit unsigned value for ELNA bypass. 2365 * 1-Enable, 0-Disable 2366 */ 2367 QCA_WLAN_VENDOR_ATTR_CONFIG_ELNA_BYPASS = 59, 2368 2369 /* 8-bit unsigned value. This attribute enables/disables the host driver 2370 * to send the Beacon Report Response with failure reason for the 2371 * scenarios where STA cannot honor the Beacon Report Request from AP. 2372 * 1-Enable, 0-Disable. 2373 */ 2374 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL = 60, 2375 2376 /* 8-bit unsigned value. This attribute enables/disables the host driver 2377 * to send roam reason information in the Reassociation Request frame to 2378 * the target AP when roaming within the same ESS. 2379 * 1-Enable, 0-Disable. 2380 */ 2381 QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON = 61, 2382 2383 /* 32-bit unsigned value to configure different PHY modes to the 2384 * driver/firmware. The possible values are defined in 2385 * enum qca_wlan_vendor_phy_mode. The configuration will be reset to 2386 * default value, i.e., QCA_WLAN_VENDOR_PHY_MODE_AUTO upon restarting 2387 * the driver. 2388 */ 2389 QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE = 62, 2390 2391 /* 8-bit unsigned value to configure the maximum supported channel width 2392 * for STA mode. If this value is configured when STA is in connected 2393 * state, it should not exceed the negotiated channel width. If it is 2394 * configured when STA is in disconnected state, the configured value 2395 * will take effect for the next immediate connection. 2396 * Possible values are: 2397 * NL80211_CHAN_WIDTH_20 2398 * NL80211_CHAN_WIDTH_40 2399 * NL80211_CHAN_WIDTH_80 2400 * NL80211_CHAN_WIDTH_80P80 2401 * NL80211_CHAN_WIDTH_160 2402 */ 2403 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_WIDTH = 63, 2404 2405 /* 8-bit unsigned value to enable/disable dynamic bandwidth adjustment. 2406 * This attribute is only applicable for STA mode. When dynamic 2407 * bandwidth adjustment is disabled, STA will use static channel width 2408 * the value of which is negotiated during connection. 2409 * 1-enable (default), 0-disable 2410 */ 2411 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_BW = 64, 2412 2413 /* 8-bit unsigned value to configure the maximum number of subframes of 2414 * TX MSDU for aggregation. Possible values are 0-31. When set to 0, 2415 * it is decided by the hardware. 2416 */ 2417 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MSDU_AGGREGATION = 65, 2418 2419 /* 8-bit unsigned value to configure the maximum number of subframes of 2420 * RX MSDU for aggregation. Possible values are 0-31. When set to 0, 2421 * it is decided by the hardware. 2422 */ 2423 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MSDU_AGGREGATION = 66, 2424 2425 /* 8-bit unsigned value. This attribute is used to dynamically 2426 * enable/disable the LDPC capability of the device. When configured in 2427 * the disconnected state, the updated configuration will be considered 2428 * for the immediately following connection attempt. If this 2429 * configuration is modified while the device is in the connected state, 2430 * the LDPC TX will be updated with this configuration immediately, 2431 * while the LDPC RX configuration update will take place starting from 2432 * the subsequent association attempt. 2433 * 1-Enable, 0-Disable. 2434 */ 2435 QCA_WLAN_VENDOR_ATTR_CONFIG_LDPC = 67, 2436 2437 /* 8-bit unsigned value. This attribute is used to dynamically 2438 * enable/disable the TX STBC capability of the device. When configured 2439 * in the disconnected state, the updated configuration will be 2440 * considered for the immediately following connection attempt. If the 2441 * connection is formed with TX STBC enabled and if this configuration 2442 * is disabled during that association, the TX will be impacted 2443 * immediately. Further connection attempts will disable TX STBC. 2444 * However, enabling the TX STBC for a connected session with disabled 2445 * capability is not allowed and will fail. 2446 * 1-Enable, 0-Disable. 2447 */ 2448 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_STBC = 68, 2449 2450 /* 8-bit unsigned value. This attribute is used to dynamically 2451 * enable/disable the RX STBC capability of the device. When configured 2452 * in the disconnected state, the updated configuration will be 2453 * considered for the immediately following connection attempt. If the 2454 * configuration is modified in the connected state, there will be no 2455 * impact for the current association, but further connection attempts 2456 * will use the updated configuration. 2457 * 1-Enable, 0-Disable. 2458 */ 2459 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_STBC = 69, 2460 2461 /* 8-bit unsigned value. This attribute is used to dynamically configure 2462 * the number of spatial streams. When configured in the disconnected 2463 * state, the updated configuration will be considered for the 2464 * immediately following connection attempt. If the NSS is updated after 2465 * the connection, the updated NSS value is notified to the peer using 2466 * the Operating Mode Notification/Spatial Multiplexing Power Save 2467 * frame. The updated NSS value after the connection shall not be 2468 * greater than the one negotiated during the connection. Any such 2469 * higher value configuration shall be returned with a failure. 2470 * Only symmetric NSS configuration (such as 2X2 or 1X1) can be done 2471 * using this attribute. QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS and 2472 * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attributes shall be used to 2473 * configure the asymmetric NSS configuration (such as 1X2). 2474 */ 2475 QCA_WLAN_VENDOR_ATTR_CONFIG_NSS = 70, 2476 /* 8-bit unsigned value to trigger Optimized Power Management: 2477 * 1-Enable, 0-Disable 2478 */ 2479 QCA_WLAN_VENDOR_ATTR_CONFIG_OPTIMIZED_POWER_MANAGEMENT = 71, 2480 2481 /* 8-bit unsigned value. This attribute takes the QoS/access category 2482 * value represented by the enum qca_wlan_ac_type and expects the driver 2483 * to upgrade the UDP frames to this access category. The value of 2484 * QCA_WLAN_AC_ALL is invalid for this attribute. This will override the 2485 * DSCP value configured in the frame with the intention to only upgrade 2486 * the access category. That said, it is not intended to downgrade the 2487 * access category for the frames. 2488 * Set the value to QCA_WLAN_AC_BK if the QoS upgrade needs to be 2489 * disabled, as BK is of the lowest priority and an upgrade to it does 2490 * not result in any changes for the frames. 2491 */ 2492 QCA_WLAN_VENDOR_ATTR_CONFIG_UDP_QOS_UPGRADE = 72, 2493 2494 /* 8-bit unsigned value. This attribute is used to dynamically configure 2495 * the number of chains to be used for transmitting data. This 2496 * configuration is allowed only when in connected state and will be 2497 * effective until disconnected. The driver rejects this configuration 2498 * if the number of spatial streams being used in the current connection 2499 * cannot be supported by this configuration. 2500 */ 2501 QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_TX_CHAINS = 73, 2502 /* 8-bit unsigned value. This attribute is used to dynamically configure 2503 * the number of chains to be used for receiving data. This 2504 * configuration is allowed only when in connected state and will be 2505 * effective until disconnected. The driver rejects this configuration 2506 * if the number of spatial streams being used in the current connection 2507 * cannot be supported by this configuration. 2508 */ 2509 QCA_WLAN_VENDOR_ATTR_CONFIG_NUM_RX_CHAINS = 74, 2510 2511 /* 8-bit unsigned value to configure ANI setting type. 2512 * See &enum qca_wlan_ani_setting for possible values. 2513 */ 2514 QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_SETTING = 75, 2515 /* 32-bit signed value to configure ANI level. This is used when 2516 * ANI settings type is &QCA_WLAN_ANI_SETTING_FIXED. 2517 * The set and get of ANI level with &QCA_WLAN_ANI_SETTING_AUTO 2518 * is invalid, the driver will return a failure. 2519 */ 2520 QCA_WLAN_VENDOR_ATTR_CONFIG_ANI_LEVEL = 76, 2521 2522 /* 8-bit unsigned value. This attribute is used to dynamically configure 2523 * the number of spatial streams used for transmitting the data. When 2524 * configured in the disconnected state, the configured value will 2525 * be considered for the following connection attempt. 2526 * If the NSS is updated after the connection, the updated NSS value 2527 * is notified to the peer using the Operating Mode Notification/Spatial 2528 * Multiplexing Power Save frame. 2529 * The TX NSS value configured after the connection shall not be greater 2530 * than the value negotiated during the connection. Any such higher 2531 * value configuration shall be treated as invalid configuration by 2532 * the driver. This attribute shall be configured along with 2533 * QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute to define the symmetric 2534 * configuration (such as 2X2 or 1X1) or the asymmetric 2535 * configuration (such as 1X2). 2536 * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along 2537 * with this QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute the driver 2538 * will update the TX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS. 2539 */ 2540 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS = 77, 2541 2542 /* 8-bit unsigned value. This attribute is used to dynamically configure 2543 * the number of spatial streams used for receiving the data. When 2544 * configured in the disconnected state, the configured value will 2545 * be considered for the following connection attempt. 2546 * If the NSS is updated after the connection, the updated NSS value 2547 * is notified to the peer using the Operating Mode Notification/Spatial 2548 * Multiplexing Power Save frame. 2549 * The RX NSS value configured after the connection shall not be greater 2550 * than the value negotiated during the connection. Any such higher 2551 * value configuration shall be treated as invalid configuration by 2552 * the driver. This attribute shall be configured along with 2553 * QCA_WLAN_VENDOR_ATTR_CONFIG_TX_NSS attribute to define the symmetric 2554 * configuration (such as 2X2 or 1X1) or the asymmetric 2555 * configuration (such as 1X2). 2556 * If QCA_WLAN_VENDOR_ATTR_CONFIG_NSS attribute is also provided along 2557 * with this QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS attribute the driver 2558 * will update the RX NSS based on QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS. 2559 */ 2560 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_NSS = 78, 2561 2562 /* 2563 * 8-bit unsigned value. This attribute, when set, indicates whether the 2564 * specified interface is the primary STA interface when there are more 2565 * than one STA interfaces concurrently active. 2566 * 2567 * This configuration helps the firmware/hardware to support certain 2568 * features (e.g., roaming) on this primary interface, if the same 2569 * cannot be supported on the concurrent STA interfaces simultaneously. 2570 * 2571 * This configuration is only applicable for a single STA interface on 2572 * a device and gives the priority for it only over other concurrent STA 2573 * interfaces. 2574 * 2575 * If the device is a multi wiphy/soc, this configuration applies to a 2576 * single STA interface across the wiphys. 2577 * 2578 * 1-Enable (is the primary STA), 0-Disable (is not the primary STA) 2579 */ 2580 QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY = 79, 2581 2582 /* 2583 * 8-bit unsigned value. This attribute can be used to configure the 2584 * driver to enable/disable FT-over-DS feature. Possible values for 2585 * this attribute are 1-Enable and 0-Disable. 2586 */ 2587 QCA_WLAN_VENDOR_ATTR_CONFIG_FT_OVER_DS = 80, 2588 2589 /* 2590 * 8-bit unsigned value. This attribute can be used to configure the 2591 * firmware to enable/disable ARP/NS offload feature. Possible values 2592 * for this attribute are 0-Disable and 1-Enable. 2593 * 2594 * This attribute is only applicable for STA/P2P-Client interface, 2595 * and is optional, default behavior is ARP/NS offload enabled. 2596 * 2597 * This attribute can be set in disconnected and connected state, and 2598 * will restore to the default behavior if the interface is closed. 2599 */ 2600 QCA_WLAN_VENDOR_ATTR_CONFIG_ARP_NS_OFFLOAD = 81, 2601 2602 /* keep last */ 2603 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, 2604 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = 2605 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, 2606 }; 2607 2608 /* Compatibility defines for previously used incorrect enum 2609 * qca_wlan_vendor_attr_config names. These values should not be used in any 2610 * new implementation. */ 2611 #define QCA_WLAN_VENDOR_ATTR_DISCONNECT_IES \ 2612 QCA_WLAN_VENDOR_ATTR_CONFIG_DISCONNECT_IES 2613 #define QCA_WLAN_VENDOR_ATTR_BEACON_REPORT_FAIL \ 2614 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_REPORT_FAIL 2615 2616 /** 2617 * enum qca_wlan_ani_setting - ANI setting type 2618 * @QCA_WLAN_ANI_SETTING_AUTO: Automatically determine ANI level 2619 * @QCA_WLAN_ANI_SETTING_FIXED: Fix ANI level to the dBm parameter 2620 */ 2621 enum qca_wlan_ani_setting { 2622 QCA_WLAN_ANI_SETTING_AUTO = 0, 2623 QCA_WLAN_ANI_SETTING_FIXED = 1, 2624 }; 2625 2626 /** 2627 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration 2628 * 2629 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL: Optional (u8) 2630 * Channel number on which Access Point should restart. 2631 * Note: If both the driver and user space application supports the 6 GHz band, 2632 * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY 2633 * should be used. 2634 * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL 2635 * is still used if either of the driver or user space application doesn't 2636 * support the 6 GHz band. 2637 * 2638 * @QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY: Optional (u32) 2639 * Channel center frequency (MHz) on which the access point should restart. 2640 */ 2641 enum qca_wlan_vendor_attr_sap_config { 2642 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, 2643 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_CHANNEL = 1, 2644 2645 /* List of frequencies on which AP is expected to operate. 2646 * This is irrespective of ACS configuration. This list is a priority 2647 * based one and is looked for before the AP is created to ensure the 2648 * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in 2649 * the system. 2650 */ 2651 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, 2652 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_FREQUENCY = 3, 2653 2654 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, 2655 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = 2656 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, 2657 }; 2658 2659 /** 2660 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP 2661 * conditional channel switch 2662 */ 2663 enum qca_wlan_vendor_attr_sap_conditional_chan_switch { 2664 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, 2665 /* Priority based frequency list (an array of u32 values in host byte 2666 * order) 2667 */ 2668 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, 2669 /* Status of the conditional switch (u32). 2670 * 0: Success, Non-zero: Failure 2671 */ 2672 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, 2673 2674 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, 2675 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = 2676 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, 2677 }; 2678 2679 /** 2680 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration 2681 * 2682 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND: Required (u32) 2683 * value to specify the GPIO command. Please refer to enum qca_gpio_cmd_type 2684 * for the available values. 2685 * 2686 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM: Required (u32) 2687 * value to specify the GPIO number. 2688 * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2689 * %QCA_WLAN_VENDOR_GPIO_CONFIG or %QCA_WLAN_VENDOR_GPIO_OUTPUT. 2690 * 2691 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE: Required (u32) 2692 * value to specify the GPIO output level. Please refer to enum qca_gpio_value 2693 * for the available values. 2694 * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2695 * %QCA_WLAN_VENDOR_GPIO_OUTPUT. 2696 * 2697 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE: Optional (u32) 2698 * value to specify the GPIO pull type. Please refer to enum qca_gpio_pull_type 2699 * for the available values. 2700 * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2701 * %QCA_WLAN_VENDOR_GPIO_CONFIG and 2702 * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. 2703 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG 2704 * attribute is present. 2705 * 2706 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE: Optional (u32) 2707 * value to specify the GPIO interrupt mode. Please refer to enum 2708 * qca_gpio_interrupt_mode for the available values. 2709 * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2710 * %QCA_WLAN_VENDOR_GPIO_CONFIG and 2711 * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. 2712 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG 2713 * attribute is present. 2714 * 2715 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR: Optional (u32) 2716 * value to specify the GPIO direction. Please refer to enum qca_gpio_direction 2717 * for the available values. 2718 * This is required, when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2719 * %QCA_WLAN_VENDOR_GPIO_CONFIG and 2720 * %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG attribute is not present. 2721 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG 2722 * attribute is present. 2723 * 2724 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG: Optional (u32) 2725 * Value to specify the mux config. Meaning of a given value is dependent 2726 * on the target chipset and GPIO pin. Must be of the range 0-15. 2727 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2728 * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to 0. 2729 * 2730 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE: Optional (u32) 2731 * Value to specify the drive, refer to enum qca_gpio_drive. 2732 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2733 * %QCA_WLAN_VENDOR_GPIO_CONFIG. Defaults to QCA_WLAN_GPIO_DRIVE_2MA(0). 2734 * 2735 * @QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG: Optional (flag) 2736 * Optional when %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND is 2737 * %QCA_WLAN_VENDOR_GPIO_CONFIG. When present this attribute signals that all 2738 * other parameters for the given GPIO will be obtained from internal 2739 * configuration. Only %QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM must be 2740 * specified to indicate the GPIO pin being configured. 2741 */ 2742 enum qca_wlan_gpio_attr { 2743 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, 2744 /* Unsigned 32-bit attribute for GPIO command */ 2745 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND = 1, 2746 /* Unsigned 32-bit attribute for GPIO PIN number to configure */ 2747 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM = 2, 2748 /* Unsigned 32-bit attribute for GPIO value to configure */ 2749 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE = 3, 2750 /* Unsigned 32-bit attribute for GPIO pull type */ 2751 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE = 4, 2752 /* Unsigned 32-bit attribute for GPIO interrupt mode */ 2753 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE = 5, 2754 /* Unsigned 32-bit attribute for GPIO direction to configure */ 2755 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DIR = 6, 2756 /* Unsigned 32-bit attribute for GPIO mux config */ 2757 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MUX_CONFIG = 7, 2758 /* Unsigned 32-bit attribute for GPIO drive */ 2759 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_DRIVE = 8, 2760 /* Flag attribute for using internal GPIO configuration */ 2761 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTERNAL_CONFIG = 9, 2762 2763 /* keep last */ 2764 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, 2765 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = 2766 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1 2767 }; 2768 2769 /** 2770 * enum gpio_cmd_type - GPIO configuration command type 2771 * @QCA_WLAN_VENDOR_GPIO_CONFIG: Set GPIO configuration info 2772 * @QCA_WLAN_VENDOR_GPIO_OUTPUT: Set GPIO output level 2773 */ 2774 enum qca_gpio_cmd_type { 2775 QCA_WLAN_VENDOR_GPIO_CONFIG = 0, 2776 QCA_WLAN_VENDOR_GPIO_OUTPUT = 1, 2777 }; 2778 2779 /** 2780 * enum qca_gpio_pull_type - GPIO pull type 2781 * @QCA_WLAN_GPIO_PULL_NONE: Set GPIO pull type to none 2782 * @QCA_WLAN_GPIO_PULL_UP: Set GPIO pull up 2783 * @QCA_WLAN_GPIO_PULL_DOWN: Set GPIO pull down 2784 */ 2785 enum qca_gpio_pull_type { 2786 QCA_WLAN_GPIO_PULL_NONE = 0, 2787 QCA_WLAN_GPIO_PULL_UP = 1, 2788 QCA_WLAN_GPIO_PULL_DOWN = 2, 2789 QCA_WLAN_GPIO_PULL_MAX, 2790 }; 2791 2792 /** 2793 * enum qca_gpio_direction - GPIO direction 2794 * @QCA_WLAN_GPIO_INPUT: Set GPIO as input mode 2795 * @QCA_WLAN_GPIO_OUTPUT: Set GPIO as output mode 2796 * @QCA_WLAN_GPIO_VALUE_MAX: Invalid value 2797 */ 2798 enum qca_gpio_direction { 2799 QCA_WLAN_GPIO_INPUT = 0, 2800 QCA_WLAN_GPIO_OUTPUT = 1, 2801 QCA_WLAN_GPIO_DIR_MAX, 2802 }; 2803 2804 /** 2805 * enum qca_gpio_value - GPIO Value 2806 * @QCA_WLAN_GPIO_LEVEL_LOW: set gpio output level to low 2807 * @QCA_WLAN_GPIO_LEVEL_HIGH: set gpio output level to high 2808 * @QCA_WLAN_GPIO_LEVEL_MAX: Invalid value 2809 */ 2810 enum qca_gpio_value { 2811 QCA_WLAN_GPIO_LEVEL_LOW = 0, 2812 QCA_WLAN_GPIO_LEVEL_HIGH = 1, 2813 QCA_WLAN_GPIO_LEVEL_MAX, 2814 }; 2815 2816 /** 2817 * enum gpio_interrupt_mode - GPIO interrupt mode 2818 * @QCA_WLAN_GPIO_INTMODE_DISABLE: Disable interrupt trigger 2819 * @QCA_WLAN_GPIO_INTMODE_RISING_EDGE: Interrupt with GPIO rising edge trigger 2820 * @QCA_WLAN_GPIO_INTMODE_FALLING_EDGE: Interrupt with GPIO falling edge trigger 2821 * @QCA_WLAN_GPIO_INTMODE_BOTH_EDGE: Interrupt with GPIO both edge trigger 2822 * @QCA_WLAN_GPIO_INTMODE_LEVEL_LOW: Interrupt with GPIO level low trigger 2823 * @QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH: Interrupt with GPIO level high trigger 2824 * @QCA_WLAN_GPIO_INTMODE_MAX: Invalid value 2825 */ 2826 enum qca_gpio_interrupt_mode { 2827 QCA_WLAN_GPIO_INTMODE_DISABLE = 0, 2828 QCA_WLAN_GPIO_INTMODE_RISING_EDGE = 1, 2829 QCA_WLAN_GPIO_INTMODE_FALLING_EDGE = 2, 2830 QCA_WLAN_GPIO_INTMODE_BOTH_EDGE = 3, 2831 QCA_WLAN_GPIO_INTMODE_LEVEL_LOW = 4, 2832 QCA_WLAN_GPIO_INTMODE_LEVEL_HIGH = 5, 2833 QCA_WLAN_GPIO_INTMODE_MAX, 2834 }; 2835 2836 /** 2837 * enum qca_gpio_drive - GPIO drive 2838 * @QCA_WLAN_GPIO_DRIVE_2MA: drive 2MA 2839 * @QCA_WLAN_GPIO_DRIVE_4MA: drive 4MA 2840 * @QCA_WLAN_GPIO_DRIVE_6MA: drive 6MA 2841 * @QCA_WLAN_GPIO_DRIVE_8MA: drive 8MA 2842 * @QCA_WLAN_GPIO_DRIVE_10MA: drive 10MA 2843 * @QCA_WLAN_GPIO_DRIVE_12MA: drive 12MA 2844 * @QCA_WLAN_GPIO_DRIVE_14MA: drive 14MA 2845 * @QCA_WLAN_GPIO_DRIVE_16MA: drive 16MA 2846 * @QCA_WLAN_GPIO_DRIVE_MAX: invalid GPIO drive 2847 */ 2848 enum qca_gpio_drive { 2849 QCA_WLAN_GPIO_DRIVE_2MA = 0, 2850 QCA_WLAN_GPIO_DRIVE_4MA = 1, 2851 QCA_WLAN_GPIO_DRIVE_6MA = 2, 2852 QCA_WLAN_GPIO_DRIVE_8MA = 3, 2853 QCA_WLAN_GPIO_DRIVE_10MA = 4, 2854 QCA_WLAN_GPIO_DRIVE_12MA = 5, 2855 QCA_WLAN_GPIO_DRIVE_14MA = 6, 2856 QCA_WLAN_GPIO_DRIVE_16MA = 7, 2857 QCA_WLAN_GPIO_DRIVE_MAX, 2858 }; 2859 2860 /** 2861 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting 2862 * MSDUQ depth threshold per peer per tid in the target 2863 * 2864 * Associated Vendor Command: 2865 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH 2866 */ 2867 enum qca_wlan_set_qdepth_thresh_attr { 2868 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, 2869 /* 6-byte MAC address */ 2870 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, 2871 /* Unsigned 32-bit attribute for holding the TID */ 2872 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, 2873 /* Unsigned 32-bit attribute for holding the update mask 2874 * bit 0 - Update high priority msdu qdepth threshold 2875 * bit 1 - Update low priority msdu qdepth threshold 2876 * bit 2 - Update UDP msdu qdepth threshold 2877 * bit 3 - Update Non UDP msdu qdepth threshold 2878 * rest of bits are reserved 2879 */ 2880 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, 2881 /* Unsigned 32-bit attribute for holding the threshold value */ 2882 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, 2883 2884 /* keep last */ 2885 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, 2886 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = 2887 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, 2888 }; 2889 2890 /** 2891 * enum qca_acs_dfs_mode - Defines different types of DFS channel 2892 * configurations for ACS operation. 2893 * 2894 * @QCA_ACS_DFS_MODE_NONE: Refer to invalid DFS mode 2895 * @QCA_ACS_DFS_MODE_ENABLE: Consider DFS channels in ACS operation 2896 * @QCA_ACS_DFS_MODE_DISABLE: Do not consider DFS channels in ACS operation 2897 * @QCA_ACS_DFS_MODE_DEPRIORITIZE: Deprioritize DFS channels in ACS operation 2898 */ 2899 enum qca_acs_dfs_mode { 2900 QCA_ACS_DFS_MODE_NONE = 0, 2901 QCA_ACS_DFS_MODE_ENABLE = 1, 2902 QCA_ACS_DFS_MODE_DISABLE = 2, 2903 QCA_ACS_DFS_MODE_DEPRIORITIZE = 3, 2904 }; 2905 2906 /** 2907 * enum qca_wlan_vendor_attr_acs_config - Defines Configuration attributes 2908 * used by the vendor command QCA_NL80211_VENDOR_SUBCMD_ACS_POLICY. 2909 * 2910 * @QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE: Required (u8) 2911 * DFS mode for ACS operation from enum qca_acs_dfs_mode. 2912 * 2913 * @QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT: Required (u8) 2914 * channel number hint for ACS operation, if valid channel is specified then 2915 * ACS operation gives priority to this channel. 2916 * Note: If both the driver and user space application supports the 6 GHz band, 2917 * this attribute is deprecated and QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT 2918 * should be used. 2919 * To maintain backward compatibility, QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT 2920 * is still used if either of the driver or user space application doesn't 2921 * support the 6 GHz band. 2922 * 2923 * @QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT: Required (u32). 2924 * Channel center frequency (MHz) hint for ACS operation, if a valid center 2925 * frequency is specified, ACS operation gives priority to this channel. 2926 */ 2927 enum qca_wlan_vendor_attr_acs_config { 2928 QCA_WLAN_VENDOR_ATTR_ACS_MODE_INVALID = 0, 2929 QCA_WLAN_VENDOR_ATTR_ACS_DFS_MODE = 1, 2930 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_HINT = 2, 2931 QCA_WLAN_VENDOR_ATTR_ACS_FREQUENCY_HINT = 3, 2932 2933 QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST, 2934 QCA_WLAN_VENDOR_ATTR_ACS_DFS_MAX = 2935 QCA_WLAN_VENDOR_ATTR_ACS_DFS_AFTER_LAST - 1, 2936 }; 2937 2938 /** 2939 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability 2940 */ 2941 enum qca_wlan_vendor_attr_get_hw_capability { 2942 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, 2943 /* Antenna isolation 2944 * An attribute used in the response. 2945 * The content of this attribute is encoded in a byte array. Each byte 2946 * value is an antenna isolation value. The array length is the number 2947 * of antennas. 2948 */ 2949 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, 2950 /* Request HW capability 2951 * An attribute used in the request. 2952 * The content of this attribute is a u32 array for one or more of 2953 * hardware capabilities (attribute IDs) that are being requested. Each 2954 * u32 value has a value from this 2955 * enum qca_wlan_vendor_attr_get_hw_capability 2956 * identifying which capabilities are requested. 2957 */ 2958 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, 2959 2960 /* keep last */ 2961 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, 2962 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = 2963 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, 2964 }; 2965 2966 /** 2967 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring 2968 * offload which is an extension for LL_STATS. 2969 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. 2970 * If MAC counters do not exceed the threshold, FW will report monitored 2971 * link layer counters periodically as this setting. The first report is 2972 * always triggered by this timer. 2973 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). 2974 * For each MAC layer counter, FW holds two copies. One is the current value. 2975 * The other is the last report. Once a current counter's increment is larger 2976 * than the threshold, FW will indicate that counter to host even if the 2977 * monitoring timer does not expire. 2978 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change 2979 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU 2980 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same 2981 * failure code. 2982 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code 2983 * 1: TX packet discarded 2984 * 2: No ACK 2985 * 3: Postpone 2986 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address 2987 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state 2988 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. 2989 * Threshold for all monitored parameters. If per counter dedicated threshold 2990 * is not enabled, this threshold will take effect. 2991 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this 2992 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. 2993 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID 2994 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID 2995 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters 2996 * Bit0: TX counter unit in MSDU 2997 * Bit1: TX counter unit in MPDU 2998 * Bit2: TX counter unit in PPDU 2999 * Bit3: TX counter unit in byte 3000 * Bit4: Dropped MSDUs 3001 * Bit5: Dropped Bytes 3002 * Bit6: MPDU retry counter 3003 * Bit7: MPDU failure counter 3004 * Bit8: PPDU failure counter 3005 * Bit9: MPDU aggregation counter 3006 * Bit10: MCS counter for ACKed MPDUs 3007 * Bit11: MCS counter for Failed MPDUs 3008 * Bit12: TX Delay counter 3009 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters 3010 * Bit0: MAC RX counter unit in MPDU 3011 * Bit1: MAC RX counter unit in byte 3012 * Bit2: PHY RX counter unit in PPDU 3013 * Bit3: PHY RX counter unit in byte 3014 * Bit4: Disorder counter 3015 * Bit5: Retry counter 3016 * Bit6: Duplication counter 3017 * Bit7: Discard counter 3018 * Bit8: MPDU aggregation size counter 3019 * Bit9: MCS counter 3020 * Bit10: Peer STA power state change (wake to sleep) counter 3021 * Bit11: Peer STA power save counter, total time in PS mode 3022 * Bit12: Probe request counter 3023 * Bit13: Other management frames counter 3024 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA 3025 * Bit0: Idle time 3026 * Bit1: TX time 3027 * Bit2: time RX in current bss 3028 * Bit3: Out of current bss time 3029 * Bit4: Wireless medium busy time 3030 * Bit5: RX in bad condition time 3031 * Bit6: TX in bad condition time 3032 * Bit7: time wlan card not available 3033 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal 3034 * Bit0: Per channel SNR counter 3035 * Bit1: Per channel noise floor counter 3036 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers 3037 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels 3038 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats 3039 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats 3040 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats 3041 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs 3042 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs 3043 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs 3044 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data 3045 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets 3046 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped 3047 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK 3048 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed 3049 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed 3050 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: 3051 * aggregation stats buffer length 3052 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats 3053 * buffer for ACKed MPDUs. 3054 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats 3055 * buffer for failed MPDUs. 3056 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: 3057 * length of delay stats array. 3058 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats 3059 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs 3060 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs 3061 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats 3062 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received 3063 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received 3064 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received 3065 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received 3066 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost 3067 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets 3068 * flagged as retransmissions 3069 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets 3070 * flagged as duplicated 3071 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX 3072 * packets discarded 3073 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation 3074 * stats buffer. 3075 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs 3076 * stats buffer. 3077 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer 3078 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer 3079 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep 3080 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time 3081 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe 3082 * requests received 3083 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt 3084 * frames received 3085 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time 3086 * there is no TX, nor RX, nor interference. 3087 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time 3088 * transmitting packets. 3089 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time 3090 * for receiving. 3091 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time 3092 * interference detected. 3093 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time 3094 * receiving packets with errors. 3095 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time 3096 * TX no-ACK. 3097 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time 3098 * the chip is unable to work in normal conditions. 3099 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time 3100 * receiving packets in current BSS. 3101 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time 3102 * receiving packets not in current BSS. 3103 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas 3104 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: 3105 * This is a container for per antenna signal stats. 3106 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value 3107 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value 3108 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon 3109 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon 3110 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64 3111 * Absolute timestamp from 1970/1/1, unit in ms. After receiving the 3112 * message, user layer APP could call gettimeofday to get another 3113 * timestamp and calculate transfer delay for the message. 3114 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32 3115 * Real period for this measurement, unit in us. 3116 */ 3117 enum qca_wlan_vendor_attr_ll_stats_ext { 3118 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, 3119 3120 /* Attributes for configurations */ 3121 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, 3122 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, 3123 3124 /* Peer STA power state change */ 3125 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, 3126 3127 /* TX failure event */ 3128 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, 3129 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, 3130 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, 3131 3132 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, 3133 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, 3134 3135 /* MAC counters */ 3136 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, 3137 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, 3138 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, 3139 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, 3140 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, 3141 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, 3142 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, 3143 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, 3144 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, 3145 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, 3146 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, 3147 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, 3148 3149 /* Sub-attributes for PEER_AC_TX */ 3150 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, 3151 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, 3152 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, 3153 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, 3154 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, 3155 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, 3156 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, 3157 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, 3158 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, 3159 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, 3160 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, 3161 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, 3162 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, 3163 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, 3164 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, 3165 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, 3166 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, 3167 3168 /* Sub-attributes for PEER_AC_RX */ 3169 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, 3170 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, 3171 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, 3172 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, 3173 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, 3174 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, 3175 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, 3176 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, 3177 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, 3178 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, 3179 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, 3180 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, 3181 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, 3182 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, 3183 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, 3184 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, 3185 3186 /* Sub-attributes for CCA_BSS */ 3187 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, 3188 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, 3189 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, 3190 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, 3191 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, 3192 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, 3193 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, 3194 3195 /* sub-attribute for BSS_RX_TIME */ 3196 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, 3197 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, 3198 3199 /* Sub-attributes for PEER_SIGNAL */ 3200 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, 3201 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, 3202 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, 3203 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, 3204 3205 /* Sub-attributes for IFACE_BSS */ 3206 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, 3207 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, 3208 3209 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME, 3210 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME, 3211 3212 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, 3213 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = 3214 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 3215 }; 3216 3217 /* Attributes for FTM commands and events */ 3218 3219 /** 3220 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities 3221 * 3222 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See 3223 * enum qca_wlan_vendor_attr_loc_capa_flags. 3224 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number 3225 * of measurement sessions that can run concurrently. 3226 * Default is one session (no session concurrency). 3227 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique 3228 * peers that are supported in running sessions. For example, 3229 * if the value is 8 and maximum number of sessions is 2, you can 3230 * have one session with 8 unique peers, or 2 sessions with 4 unique 3231 * peers each, and so on. 3232 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number 3233 * of bursts per peer, as an exponent (2^value). Default is 0, 3234 * meaning no multi-burst support. 3235 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number 3236 * of measurement exchanges allowed in a single burst. 3237 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement 3238 * types. A bit mask (unsigned 32 bit value), each bit corresponds 3239 * to an AOA type as defined by enum qca_vendor_attr_aoa_type. 3240 */ 3241 enum qca_wlan_vendor_attr_loc_capa { 3242 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, 3243 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, 3244 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, 3245 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, 3246 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, 3247 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, 3248 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, 3249 /* keep last */ 3250 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, 3251 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = 3252 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, 3253 }; 3254 3255 /** 3256 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags 3257 * 3258 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver 3259 * can be configured as an FTM responder (for example, an AP that 3260 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 3261 * will be supported if set. 3262 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver 3263 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION 3264 * will be supported if set. 3265 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder 3266 * supports immediate (ASAP) response. 3267 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone 3268 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. 3269 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports 3270 * requesting AOA measurements as part of an FTM session. 3271 */ 3272 enum qca_wlan_vendor_attr_loc_capa_flags { 3273 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, 3274 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, 3275 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, 3276 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, 3277 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, 3278 }; 3279 3280 /** 3281 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about 3282 * a single peer in a measurement session. 3283 * 3284 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. 3285 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related 3286 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. 3287 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of 3288 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 3289 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for 3290 * list of supported attributes. 3291 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for 3292 * secure measurement. 3293 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA 3294 * measurement every <value> bursts. If 0 or not specified, 3295 * AOA measurements will be disabled for this peer. 3296 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where 3297 * the measurement frames are exchanged. Optional; if not 3298 * specified, try to locate the peer in the kernel scan 3299 * results cache and use frequency from there. 3300 */ 3301 enum qca_wlan_vendor_attr_ftm_peer_info { 3302 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, 3303 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, 3304 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, 3305 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, 3306 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, 3307 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, 3308 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, 3309 /* keep last */ 3310 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, 3311 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = 3312 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, 3313 }; 3314 3315 /** 3316 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, 3317 * per-peer 3318 * 3319 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request 3320 * immediate (ASAP) response from peer. 3321 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request 3322 * LCI report from peer. The LCI report includes the absolute 3323 * location of the peer in "official" coordinates (similar to GPS). 3324 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. 3325 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request 3326 * Location civic report from peer. The LCR includes the location 3327 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, 3328 * 11.24.6.7 for more information. 3329 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, 3330 * request a secure measurement. 3331 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. 3332 */ 3333 enum qca_wlan_vendor_attr_ftm_peer_meas_flags { 3334 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, 3335 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, 3336 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, 3337 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, 3338 }; 3339 3340 /** 3341 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters 3342 * 3343 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements 3344 * to perform in a single burst. 3345 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to 3346 * perform, specified as an exponent (2^value). 3347 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst 3348 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. 3349 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, 3350 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must 3351 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. 3352 */ 3353 enum qca_wlan_vendor_attr_ftm_meas_param { 3354 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, 3355 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, 3356 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, 3357 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, 3358 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, 3359 /* keep last */ 3360 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, 3361 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = 3362 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, 3363 }; 3364 3365 /** 3366 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results 3367 * 3368 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported 3369 * peer. 3370 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement 3371 * request for this peer. 3372 * See enum qca_wlan_vendor_attr_ftm_peer_result_status. 3373 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related 3374 * to measurement results for this peer. 3375 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. 3376 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when 3377 * request failed and peer requested not to send an additional request 3378 * for this number of seconds. 3379 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received 3380 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 3381 * 9.4.2.22.10. 3382 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when 3383 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 3384 * 9.4.2.22.13. 3385 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer 3386 * overridden some measurement request parameters. See 3387 * enum qca_wlan_vendor_attr_ftm_meas_param. 3388 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement 3389 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 3390 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement 3391 * results. Each entry is a nested attribute defined 3392 * by enum qca_wlan_vendor_attr_ftm_meas. 3393 */ 3394 enum qca_wlan_vendor_attr_ftm_peer_result { 3395 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, 3396 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, 3397 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, 3398 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, 3399 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, 3400 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, 3401 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, 3402 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, 3403 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, 3404 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, 3405 /* keep last */ 3406 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, 3407 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = 3408 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, 3409 }; 3410 3411 /** 3412 * enum qca_wlan_vendor_attr_ftm_peer_result_status 3413 * 3414 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results 3415 * will be provided. Peer may have overridden some measurement parameters, 3416 * in which case overridden parameters will be report by 3417 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. 3418 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable 3419 * of performing the measurement request. No more results will be sent 3420 * for this peer in this session. 3421 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request 3422 * failed, and requested not to send an additional request for number 3423 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS 3424 * attribute. 3425 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation 3426 * failed. Request was not sent over the air. 3427 */ 3428 enum qca_wlan_vendor_attr_ftm_peer_result_status { 3429 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, 3430 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, 3431 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, 3432 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, 3433 }; 3434 3435 /** 3436 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags 3437 * for measurement result, per-peer 3438 * 3439 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, 3440 * measurement completed for this peer. No more results will be reported 3441 * for this peer in this session. 3442 */ 3443 enum qca_wlan_vendor_attr_ftm_peer_result_flags { 3444 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, 3445 }; 3446 3447 /** 3448 * enum qca_vendor_attr_loc_session_status: Session completion status code 3449 * 3450 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed 3451 * successfully. 3452 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted 3453 * by request. 3454 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request 3455 * was invalid and was not started. 3456 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error 3457 * and did not complete normally (for example out of resources). 3458 */ 3459 enum qca_vendor_attr_loc_session_status { 3460 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, 3461 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, 3462 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, 3463 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, 3464 }; 3465 3466 /** 3467 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data 3468 * 3469 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as 3470 * recorded by responder, in picoseconds. 3471 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 3472 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at 3473 * initiator, in picoseconds. 3474 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 3475 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by 3476 * initiator, in picoseconds. 3477 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 3478 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at 3479 * responder, in picoseconds. 3480 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 3481 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded 3482 * during this measurement exchange. Optional and will be provided if 3483 * the hardware can measure it. 3484 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by 3485 * responder. Not always provided. 3486 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 3487 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by 3488 * responder. Not always provided. 3489 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 3490 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by 3491 * initiator. Not always provided. 3492 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 3493 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by 3494 * initiator. Not always provided. 3495 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 3496 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. 3497 */ 3498 enum qca_wlan_vendor_attr_ftm_meas { 3499 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, 3500 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, 3501 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, 3502 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, 3503 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, 3504 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, 3505 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, 3506 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, 3507 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, 3508 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, 3509 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, 3510 /* keep last */ 3511 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, 3512 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = 3513 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, 3514 }; 3515 3516 /** 3517 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type 3518 * 3519 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest 3520 * CIR (channel impulse response) path for each antenna. 3521 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude 3522 * of the strongest CIR path for each antenna. 3523 */ 3524 enum qca_wlan_vendor_attr_aoa_type { 3525 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, 3526 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, 3527 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX 3528 }; 3529 3530 /** 3531 * enum qca_wlan_vendor_attr_encryption_test - Attributes to 3532 * validate encryption engine 3533 * 3534 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. 3535 * This will be included if the request is for decryption; if not included, 3536 * the request is treated as a request for encryption by default. 3537 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value 3538 * indicating the key cipher suite. Takes same values as 3539 * NL80211_ATTR_KEY_CIPHER. 3540 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value 3541 * Key Id to be used for encryption 3542 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. 3543 * Key (TK) to be used for encryption/decryption 3544 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. 3545 * Packet number to be specified for encryption/decryption 3546 * 6 bytes for TKIP/CCMP/GCMP. 3547 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values 3548 * representing the 802.11 packet (header + payload + FCS) that 3549 * needs to be encrypted/decrypted. 3550 * Encrypted/decrypted response from the driver will also be sent 3551 * to userspace with the same attribute. 3552 */ 3553 enum qca_wlan_vendor_attr_encryption_test { 3554 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, 3555 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, 3556 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, 3557 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, 3558 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, 3559 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, 3560 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, 3561 3562 /* keep last */ 3563 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, 3564 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = 3565 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 3566 }; 3567 3568 /** 3569 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of 3570 * sector for DMG RF sector operations. 3571 * 3572 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector 3573 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector 3574 */ 3575 enum qca_wlan_vendor_attr_dmg_rf_sector_type { 3576 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, 3577 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, 3578 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX 3579 }; 3580 3581 /** 3582 * enum qca_wlan_vendor_attr_fw_state - State of firmware 3583 * 3584 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state 3585 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active 3586 */ 3587 enum qca_wlan_vendor_attr_fw_state { 3588 QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, 3589 QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, 3590 QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX 3591 }; 3592 3593 /** 3594 * BRP antenna limit mode 3595 * 3596 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force 3597 * antenna limit, BRP will be performed as usual. 3598 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal 3599 * antennas limit. the hardware may use less antennas than the 3600 * maximum limit. 3601 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will 3602 * use exactly the specified number of antennas for BRP. 3603 */ 3604 enum qca_wlan_vendor_attr_brp_ant_limit_mode { 3605 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, 3606 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, 3607 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, 3608 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX 3609 }; 3610 3611 /** 3612 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for 3613 * DMG RF sector configuration for a single RF module. 3614 * The values are defined in a compact way which closely matches 3615 * the way it is stored in HW registers. 3616 * The configuration provides values for 32 antennas and 8 distribution 3617 * amplifiers, and together describes the characteristics of the RF 3618 * sector - such as a beam in some direction with some gain. 3619 * 3620 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index 3621 * of RF module for this configuration. 3622 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge 3623 * amplifier gain index. Unsigned 32 bit number containing 3624 * bits for all 32 antennas. 3625 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge 3626 * amplifier gain index. Unsigned 32 bit number containing 3627 * bits for all 32 antennas. 3628 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge 3629 * amplifier gain index. Unsigned 32 bit number containing 3630 * bits for all 32 antennas. 3631 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values 3632 * for first 16 antennas, 2 bits per antenna. 3633 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values 3634 * for last 16 antennas, 2 bits per antenna. 3635 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains 3636 * DTYPE values (3 bits) for each distribution amplifier, followed 3637 * by X16 switch bits for each distribution amplifier. There are 3638 * total of 8 distribution amplifiers. 3639 */ 3640 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { 3641 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, 3642 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, 3643 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, 3644 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, 3645 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, 3646 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, 3647 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, 3648 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, 3649 3650 /* keep last */ 3651 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, 3652 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = 3653 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 3654 }; 3655 3656 enum qca_wlan_vendor_attr_ll_stats_set { 3657 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, 3658 /* Unsigned 32-bit value */ 3659 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, 3660 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, 3661 /* keep last */ 3662 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, 3663 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = 3664 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, 3665 }; 3666 3667 enum qca_wlan_vendor_attr_ll_stats_clr { 3668 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, 3669 /* Unsigned 32bit bitmap for clearing statistics 3670 * All radio statistics 0x00000001 3671 * cca_busy_time (within radio statistics) 0x00000002 3672 * All channel stats (within radio statistics) 0x00000004 3673 * All scan statistics (within radio statistics) 0x00000008 3674 * All interface statistics 0x00000010 3675 * All tx rate statistics (within interface statistics) 0x00000020 3676 * All ac statistics (with in interface statistics) 0x00000040 3677 * All contention (min, max, avg) statistics (within ac statisctics) 3678 * 0x00000080. 3679 */ 3680 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, 3681 /* Unsigned 8 bit value: Request to stop statistics collection */ 3682 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, 3683 3684 /* Unsigned 32 bit bitmap: Response from the driver 3685 * for the cleared statistics 3686 */ 3687 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, 3688 /* Unsigned 8 bit value: Response from driver/firmware 3689 * for the stop request 3690 */ 3691 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, 3692 /* keep last */ 3693 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, 3694 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = 3695 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, 3696 }; 3697 3698 enum qca_wlan_vendor_attr_ll_stats_get { 3699 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, 3700 /* Unsigned 32 bit value provided by the caller issuing the GET stats 3701 * command. When reporting the stats results, the driver uses the same 3702 * value to indicate which GET request the results correspond to. 3703 */ 3704 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, 3705 /* Unsigned 32 bit value - bit mask to identify what statistics are 3706 * requested for retrieval. 3707 * Radio Statistics 0x00000001 3708 * Interface Statistics 0x00000020 3709 * All Peer Statistics 0x00000040 3710 * Peer Statistics 0x00000080 3711 */ 3712 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, 3713 /* keep last */ 3714 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, 3715 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = 3716 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, 3717 }; 3718 3719 enum qca_wlan_vendor_attr_ll_stats_results { 3720 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, 3721 /* Unsigned 32bit value. Used by the driver; must match the request id 3722 * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. 3723 */ 3724 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, 3725 3726 /* Unsigned 32 bit value */ 3727 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, 3728 /* Unsigned 32 bit value */ 3729 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, 3730 /* Unsigned 32 bit value */ 3731 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, 3732 /* Unsigned 32 bit value */ 3733 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, 3734 /* Signed 32 bit value */ 3735 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, 3736 /* Signed 32 bit value */ 3737 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, 3738 /* Signed 32 bit value */ 3739 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, 3740 3741 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are 3742 * nested within the interface stats. 3743 */ 3744 3745 /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. 3746 * Type = enum wifi_interface_mode. 3747 */ 3748 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, 3749 /* Interface MAC address. An array of 6 Unsigned int8 */ 3750 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, 3751 /* Type = enum wifi_connection_state, e.g., DISCONNECTED, 3752 * AUTHENTICATING, etc. valid for STA, CLI only. 3753 */ 3754 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, 3755 /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE 3756 */ 3757 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, 3758 /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ 3759 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, 3760 /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ 3761 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, 3762 /* BSSID. An array of 6 unsigned 8 bit values */ 3763 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, 3764 /* Country string advertised by AP. An array of 3 unsigned 8 bit 3765 * values. 3766 */ 3767 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, 3768 /* Country string for this association. An array of 3 unsigned 8 bit 3769 * values. 3770 */ 3771 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, 3772 3773 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could 3774 * be nested within the interface stats. 3775 */ 3776 3777 /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ 3778 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, 3779 /* Unsigned int 32 value corresponding to respective AC */ 3780 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, 3781 /* Unsigned int 32 value corresponding to respective AC */ 3782 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, 3783 /* Unsigned int 32 value corresponding to respective AC */ 3784 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, 3785 /* Unsigned int 32 value corresponding to respective AC */ 3786 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, 3787 /* Unsigned int 32 value corresponding to respective AC */ 3788 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, 3789 /* Unsigned int 32 value corresponding to respective AC */ 3790 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, 3791 /* Unsigned int 32 value corresponding to respective AC */ 3792 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, 3793 /* Unsigned int 32 value corresponding to respective AC */ 3794 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, 3795 /* Unsigned int 32 value corresponding to respective AC */ 3796 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, 3797 /* Unsigned int 32 values corresponding to respective AC */ 3798 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, 3799 /* Unsigned int 32 values corresponding to respective AC */ 3800 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, 3801 /* Unsigned int 32 values corresponding to respective AC */ 3802 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, 3803 /* Unsigned int 32 values corresponding to respective AC */ 3804 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, 3805 /* Unsigned int 32 values corresponding to respective AC */ 3806 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, 3807 /* Unsigned 32 bit value. Number of peers */ 3808 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, 3809 3810 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are 3811 * nested within the interface stats. 3812 */ 3813 3814 /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ 3815 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, 3816 /* MAC addr corresponding to respective peer. An array of 6 unsigned 3817 * 8 bit values. 3818 */ 3819 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, 3820 /* Unsigned int 32 bit value representing capabilities corresponding 3821 * to respective peer. 3822 */ 3823 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, 3824 /* Unsigned 32 bit value. Number of rates */ 3825 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, 3826 3827 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 3828 * are nested within the rate stat. 3829 */ 3830 3831 /* Wi-Fi Rate - separate attributes defined for individual fields */ 3832 3833 /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ 3834 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, 3835 /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ 3836 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, 3837 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ 3838 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, 3839 /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std 3840 * in the units of 0.5 Mbps HT/VHT it would be MCS index 3841 */ 3842 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, 3843 3844 /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ 3845 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, 3846 3847 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be 3848 * nested within the peer info stats. 3849 */ 3850 3851 /* Unsigned int 32 bit value. Number of successfully transmitted data 3852 * packets, i.e., with ACK received corresponding to the respective 3853 * rate. 3854 */ 3855 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, 3856 /* Unsigned int 32 bit value. Number of received data packets 3857 * corresponding to the respective rate. 3858 */ 3859 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, 3860 /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK 3861 * received corresponding to the respective rate. 3862 */ 3863 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, 3864 /* Unsigned int 32 bit value. Total number of data packet retries for 3865 * the respective rate. 3866 */ 3867 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, 3868 /* Unsigned int 32 bit value. Total number of short data packet retries 3869 * for the respective rate. 3870 */ 3871 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, 3872 /* Unsigned int 32 bit value. Total number of long data packet retries 3873 * for the respective rate. 3874 */ 3875 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, 3876 3877 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, 3878 /* Unsigned 32 bit value. Total number of msecs the radio is awake 3879 * accruing over time. 3880 */ 3881 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, 3882 /* Unsigned 32 bit value. Total number of msecs the radio is 3883 * transmitting accruing over time. 3884 */ 3885 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, 3886 /* Unsigned 32 bit value. Total number of msecs the radio is in active 3887 * receive accruing over time. 3888 */ 3889 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, 3890 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3891 * to all scan accruing over time. 3892 */ 3893 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, 3894 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3895 * to NAN accruing over time. 3896 */ 3897 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, 3898 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3899 * to GSCAN accruing over time. 3900 */ 3901 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, 3902 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3903 * to roam scan accruing over time. 3904 */ 3905 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, 3906 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3907 * to PNO scan accruing over time. 3908 */ 3909 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, 3910 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 3911 * to Hotspot 2.0 scans and GAS exchange accruing over time. 3912 */ 3913 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, 3914 /* Unsigned 32 bit value. Number of channels. */ 3915 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, 3916 3917 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could 3918 * be nested within the channel stats. 3919 */ 3920 3921 /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ 3922 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, 3923 /* Unsigned 32 bit value. Primary 20 MHz channel. */ 3924 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, 3925 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ 3926 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, 3927 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ 3928 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, 3929 3930 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be 3931 * nested within the radio stats. 3932 */ 3933 3934 /* Unsigned int 32 bit value representing total number of msecs the 3935 * radio is awake on that channel accruing over time, corresponding to 3936 * the respective channel. 3937 */ 3938 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, 3939 /* Unsigned int 32 bit value representing total number of msecs the CCA 3940 * register is busy accruing over time corresponding to the respective 3941 * channel. 3942 */ 3943 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, 3944 3945 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, 3946 3947 /* Signifies the nested list of channel attributes 3948 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* 3949 */ 3950 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, 3951 3952 /* Signifies the nested list of peer info attributes 3953 * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* 3954 */ 3955 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, 3956 3957 /* Signifies the nested list of rate info attributes 3958 * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 3959 */ 3960 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, 3961 3962 /* Signifies the nested list of wmm info attributes 3963 * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* 3964 */ 3965 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, 3966 3967 /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates 3968 * that more stats, e.g., peers or radio, are to follow in the next 3969 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. 3970 * Otherwise, it is set to 0. 3971 */ 3972 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, 3973 3974 /* Unsigned 64 bit value */ 3975 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, 3976 3977 /* Unsigned 32 bit value */ 3978 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, 3979 3980 /* Unsigned 32 bit value */ 3981 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, 3982 3983 /* Unsigned 32 bit value */ 3984 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, 3985 3986 /* Unsigned 32 bit value */ 3987 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, 3988 3989 /* Unsigned 32 bit value */ 3990 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, 3991 3992 /* Number of msecs the radio spent in transmitting for each power level 3993 */ 3994 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, 3995 3996 /* Unsigned 32 bit value */ 3997 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, 3998 /* Unsigned 32 bit value */ 3999 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, 4000 /* Unsigned 32 bit value */ 4001 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, 4002 /* Unsigned 32 bit value */ 4003 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, 4004 4005 /* Unsigned int 32 value. 4006 * Pending MSDUs corresponding to respective AC. 4007 */ 4008 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83, 4009 4010 /* u32 value representing total time in milliseconds for which the radio 4011 * is transmitting on this channel. This attribute will be nested 4012 * within QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. 4013 */ 4014 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_TX_TIME = 84, 4015 /* u32 value representing total time in milliseconds for which the radio 4016 * is receiving all 802.11 frames intended for this device on this 4017 * channel. This attribute will be nested within 4018 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO. 4019 */ 4020 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_RX_TIME = 85, 4021 /* u8 value representing the channel load percentage. Possible values 4022 * are 0-100. 4023 */ 4024 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_LOAD_PERCENTAGE = 86, 4025 /* u8 value representing the time slicing duty cycle percentage. 4026 * Possible values are 0-100. 4027 */ 4028 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_TS_DUTY_CYCLE = 87, 4029 /* keep last */ 4030 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, 4031 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = 4032 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, 4033 }; 4034 4035 enum qca_wlan_vendor_attr_ll_stats_type { 4036 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, 4037 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, 4038 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, 4039 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, 4040 4041 /* keep last */ 4042 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, 4043 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = 4044 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, 4045 }; 4046 4047 /** 4048 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for 4049 * TDLS configuration to the host driver. 4050 * 4051 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger 4052 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode 4053 * represents the different TDLS trigger modes. 4054 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within 4055 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number 4056 * of packets shall meet the criteria for implicit TDLS setup. 4057 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets 4058 * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD 4059 * to initiate a TDLS setup. 4060 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate 4061 * a TDLS Discovery to the peer. 4062 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of 4063 * discovery attempts to know the TDLS capability of the peer. A peer is 4064 * marked as TDLS not capable if there is no response for all the attempts. 4065 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) 4066 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD 4067 * number of TX / RX frames meet the criteria for TDLS teardown. 4068 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32) 4069 * of Tx/Rx packets within a duration 4070 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link. 4071 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold 4072 * corresponding to the RSSI of the peer below which a TDLS setup is 4073 * triggered. 4074 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold 4075 * corresponding to the RSSI of the peer above which a TDLS teardown is 4076 * triggered. 4077 */ 4078 enum qca_wlan_vendor_attr_tdls_configuration { 4079 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, 4080 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, 4081 4082 /* Attributes configuring the TDLS Implicit Trigger */ 4083 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, 4084 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, 4085 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, 4086 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, 4087 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, 4088 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, 4089 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, 4090 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, 4091 4092 /* keep last */ 4093 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, 4094 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = 4095 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 4096 }; 4097 4098 /** 4099 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in 4100 * the driver 4101 * 4102 * The following are the different values for 4103 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. 4104 * 4105 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown 4106 * the TDLS connection to a respective peer comes from the user space. 4107 * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN, 4108 * TDLS_DISCOVER to do this. 4109 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS 4110 * setup/teardown to the eligible peer once the configured criteria 4111 * (such as TX/RX threshold, RSSI) is met. The attributes 4112 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to 4113 * the different configuration criteria for the TDLS trigger from the 4114 * host driver. 4115 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger 4116 * the TDLS setup / teardown through the implicit mode only to the 4117 * configured MAC addresses (wpa_supplicant, with tdls_external_control=1, 4118 * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands). 4119 * External mode works on top of the implicit mode. Thus the host driver 4120 * is expected to configure in TDLS Implicit mode too to operate in 4121 * External mode. 4122 * Configuring External mode alone without Implicit mode is invalid. 4123 * 4124 * All the above implementations work as expected only when the host driver 4125 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing 4126 * that the TDLS message exchange is not internal to the host driver, but 4127 * depends on wpa_supplicant to do the message exchange. 4128 */ 4129 enum qca_wlan_vendor_tdls_trigger_mode { 4130 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, 4131 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, 4132 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, 4133 }; 4134 4135 /** 4136 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits 4137 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 4138 * that is hard-coded in the Board Data File (BDF). 4139 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 4140 * that is hard-coded in the Board Data File (BDF). 4141 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 4142 * that is hard-coded in the Board Data File (BDF). 4143 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 4144 * that is hard-coded in the Board Data File (BDF). 4145 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 4146 * that is hard-coded in the Board Data File (BDF). 4147 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any 4148 * source of SAR power limits, thereby disabling the SAR power 4149 * limit feature. 4150 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power 4151 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 4152 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power 4153 * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 4154 * 4155 * This enumerates the valid set of values that may be supplied for 4156 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of 4157 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in 4158 * the response to an instance of the 4159 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 4160 */ 4161 enum qca_vendor_attr_sar_limits_selections { 4162 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, 4163 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, 4164 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, 4165 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, 4166 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, 4167 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, 4168 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, 4169 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, 4170 }; 4171 4172 /** 4173 * enum qca_vendor_attr_sar_limits_spec_modulations - 4174 * SAR limits specification modulation 4175 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - 4176 * CCK modulation 4177 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - 4178 * OFDM modulation 4179 * 4180 * This enumerates the valid set of values that may be supplied for 4181 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an 4182 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an 4183 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor 4184 * command or in the response to an instance of the 4185 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 4186 */ 4187 enum qca_vendor_attr_sar_limits_spec_modulations { 4188 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, 4189 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, 4190 }; 4191 4192 /** 4193 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits 4194 * 4195 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to 4196 * select which SAR power limit table should be used. Valid 4197 * values are enumerated in enum 4198 * %qca_vendor_attr_sar_limits_selections. The existing SAR 4199 * power limit selection is unchanged if this attribute is not 4200 * present. 4201 * 4202 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value 4203 * which specifies the number of SAR power limit specifications 4204 * which will follow. 4205 * 4206 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power 4207 * limit specifications. The number of specifications is 4208 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each 4209 * specification contains a set of 4210 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A 4211 * specification is uniquely identified by the attributes 4212 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, 4213 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and 4214 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always 4215 * contains as a payload the attribute 4216 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT, 4217 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. 4218 * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or 4219 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is 4220 * needed based upon the value of 4221 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. 4222 * 4223 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to 4224 * indicate for which band this specification applies. Valid 4225 * values are enumerated in enum %nl80211_band (although not all 4226 * bands may be supported by a given device). If the attribute is 4227 * not supplied then the specification will be applied to all 4228 * supported bands. 4229 * 4230 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value 4231 * to indicate for which antenna chain this specification 4232 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the 4233 * attribute is not supplied then the specification will be 4234 * applied to all chains. 4235 * 4236 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) 4237 * value to indicate for which modulation scheme this 4238 * specification applies. Valid values are enumerated in enum 4239 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute 4240 * is not supplied then the specification will be applied to all 4241 * modulation schemes. 4242 * 4243 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) 4244 * value to specify the actual power limit value in units of 0.5 4245 * dBm (i.e., a value of 11 represents 5.5 dBm). 4246 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 4247 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. 4248 * 4249 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) 4250 * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. 4251 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 4252 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. 4253 * 4254 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS 4255 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. 4256 */ 4257 enum qca_vendor_attr_sar_limits { 4258 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, 4259 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, 4260 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, 4261 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, 4262 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, 4263 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, 4264 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, 4265 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, 4266 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, 4267 4268 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, 4269 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = 4270 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 4271 }; 4272 4273 /** 4274 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by 4275 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command. 4276 * 4277 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION: In a request this attribute 4278 * should be set to any U8 value to indicate that the driver version 4279 * should be returned. When enabled in this manner, in a response this 4280 * attribute will contain a string representation of the driver version. 4281 * 4282 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION: In a request this attribute 4283 * should be set to any U8 value to indicate that the firmware version 4284 * should be returned. When enabled in this manner, in a response this 4285 * attribute will contain a string representation of the firmware version. 4286 * 4287 * @QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX: In a request this attribute 4288 * should be set to any U32 value to indicate that the current radio 4289 * index should be returned. When enabled in this manner, in a response 4290 * this attribute will contain a U32 radio index value. 4291 * 4292 */ 4293 enum qca_wlan_vendor_attr_get_wifi_info { 4294 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, 4295 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, 4296 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, 4297 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_RADIO_INDEX = 3, 4298 4299 /* keep last */ 4300 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, 4301 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = 4302 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, 4303 }; 4304 4305 /* 4306 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by 4307 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command. 4308 */ 4309 enum qca_wlan_vendor_attr_wifi_logger_start { 4310 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, 4311 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, 4312 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, 4313 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, 4314 4315 /* keep last */ 4316 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, 4317 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX = 4318 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, 4319 }; 4320 4321 enum qca_wlan_vendor_attr_logger_results { 4322 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, 4323 4324 /* Unsigned 32-bit value; must match the request Id supplied by 4325 * Wi-Fi HAL in the corresponding subcmd NL msg. 4326 */ 4327 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, 4328 4329 /* Unsigned 32-bit value; used to indicate the size of memory 4330 * dump to be allocated. 4331 */ 4332 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, 4333 4334 /* keep last */ 4335 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, 4336 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = 4337 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, 4338 }; 4339 4340 /** 4341 * enum qca_scan_freq_list_type: Frequency list types 4342 * 4343 * @QCA_PREFERRED_SCAN_FREQ_LIST: The driver shall use the scan frequency list 4344 * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as 4345 * a preferred frequency list for roaming. 4346 * 4347 * @QCA_SPECIFIC_SCAN_FREQ_LIST: The driver shall use the frequency list 4348 * specified with attribute QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST as 4349 * a specific frequency list for roaming. 4350 */ 4351 enum qca_scan_freq_list_type { 4352 QCA_PREFERRED_SCAN_FREQ_LIST = 1, 4353 QCA_SPECIFIC_SCAN_FREQ_LIST = 2, 4354 }; 4355 4356 /** 4357 * enum qca_vendor_attr_scan_freq_list_scheme: Frequency list scheme 4358 * 4359 * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST: Nested attribute of u32 values 4360 * List of frequencies in MHz to be considered for a roam scan. 4361 * 4362 * @QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE: Unsigned 32-bit value. 4363 * Type of frequency list scheme being configured/gotten as defined by the 4364 * enum qca_scan_freq_list_type. 4365 */ 4366 enum qca_vendor_attr_scan_freq_list_scheme { 4367 QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST = 1, 4368 QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_TYPE = 2, 4369 4370 /* keep last */ 4371 QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST, 4372 QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_MAX = 4373 QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST_SCHEME_AFTER_LAST - 1, 4374 }; 4375 4376 /** 4377 * enum qca_roam_scan_scheme: Scan scheme 4378 * 4379 * @QCA_ROAM_SCAN_SCHEME_NO_SCAN: No frequencies specified to scan. 4380 * Indicates the driver to not scan on a Roam Trigger scenario, but 4381 * disconnect. E.g., on a BTM request from the AP the driver/firmware shall 4382 * disconnect from the current connected AP by notifying a failure 4383 * code in the BTM response. 4384 * 4385 * @QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN: Indicates the driver/firmware to 4386 * trigger partial frequency scans. These frequencies are the ones learned 4387 * or maintained by the driver based on the probability of finding the 4388 * BSSIDs in the ESS for which the roaming is triggered. 4389 * 4390 * @QCA_ROAM_SCAN_SCHEME_FULL_SCAN: Indicates the driver/firmware to 4391 * trigger the scan on all the valid frequencies to find better 4392 * candidates to roam. 4393 */ 4394 enum qca_roam_scan_scheme { 4395 QCA_ROAM_SCAN_SCHEME_NO_SCAN = 0, 4396 QCA_ROAM_SCAN_SCHEME_PARTIAL_SCAN = 1, 4397 QCA_ROAM_SCAN_SCHEME_FULL_SCAN = 2, 4398 }; 4399 4400 /* 4401 * enum qca_vendor_roam_triggers: Bitmap of roaming triggers 4402 * 4403 * @QCA_ROAM_TRIGGER_REASON_PER: Set if the roam has to be triggered based on 4404 * a bad packet error rates (PER). 4405 * @QCA_ROAM_TRIGGER_REASON_BEACON_MISS: Set if the roam has to be triggered 4406 * based on beacon misses from the connected AP. 4407 * @QCA_ROAM_TRIGGER_REASON_POOR_RSSI: Set if the roam has to be triggered 4408 * due to poor RSSI of the connected AP. 4409 * @QCA_ROAM_TRIGGER_REASON_BETTER_RSSI: Set if the roam has to be triggered 4410 * upon finding a BSSID with a better RSSI than the connected BSSID. 4411 * Here the RSSI of the current BSSID need not be poor. 4412 * @QCA_ROAM_TRIGGER_REASON_PERIODIC: Set if the roam has to be triggered 4413 * by triggering a periodic scan to find a better AP to roam. 4414 * @QCA_ROAM_TRIGGER_REASON_DENSE: Set if the roam has to be triggered 4415 * when the connected channel environment is too noisy/congested. 4416 * @QCA_ROAM_TRIGGER_REASON_BTM: Set if the roam has to be triggered 4417 * when BTM Request frame is received from the connected AP. 4418 * @QCA_ROAM_TRIGGER_REASON_BSS_LOAD: Set if the roam has to be triggered 4419 * when the channel utilization is goes above the configured threshold. 4420 * @QCA_ROAM_TRIGGER_REASON_USER_TRIGGER: Set if the roam has to be triggered 4421 * based on the request from the user (space). 4422 * @QCA_ROAM_TRIGGER_REASON_DEAUTH: Set if the roam has to be triggered when 4423 * device receives Deauthentication/Disassociation frame from connected AP. 4424 * @QCA_ROAM_TRIGGER_REASON_IDLE: Set if the roam has to be triggered when the 4425 * device is in idle state (no TX/RX) and suspend mode, if the current RSSI 4426 * is determined to be a poor one. 4427 * @QCA_ROAM_TRIGGER_REASON_TX_FAILURES: Set if the roam has to be triggered 4428 * based on continuous TX Data frame failures to the connected AP. 4429 * @QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN: Set if the roam has to be triggered 4430 * based on the scan results obtained from an external scan (not triggered 4431 * to aim roaming). 4432 * 4433 * Set the corresponding roam trigger reason bit to consider it for roam 4434 * trigger. 4435 * Userspace can set multiple bits and send to the driver. The driver shall 4436 * consider all of them to trigger/initiate a roam scan. 4437 */ 4438 enum qca_vendor_roam_triggers { 4439 QCA_ROAM_TRIGGER_REASON_PER = 1 << 0, 4440 QCA_ROAM_TRIGGER_REASON_BEACON_MISS = 1 << 1, 4441 QCA_ROAM_TRIGGER_REASON_POOR_RSSI = 1 << 2, 4442 QCA_ROAM_TRIGGER_REASON_BETTER_RSSI = 1 << 3, 4443 QCA_ROAM_TRIGGER_REASON_PERIODIC = 1 << 4, 4444 QCA_ROAM_TRIGGER_REASON_DENSE = 1 << 5, 4445 QCA_ROAM_TRIGGER_REASON_BTM = 1 << 6, 4446 QCA_ROAM_TRIGGER_REASON_BSS_LOAD = 1 << 7, 4447 QCA_ROAM_TRIGGER_REASON_USER_TRIGGER = 1 << 8, 4448 QCA_ROAM_TRIGGER_REASON_DEAUTH = 1 << 9, 4449 QCA_ROAM_TRIGGER_REASON_IDLE = 1 << 10, 4450 QCA_ROAM_TRIGGER_REASON_TX_FAILURES = 1 << 11, 4451 QCA_ROAM_TRIGGER_REASON_EXTERNAL_SCAN = 1 << 12, 4452 }; 4453 4454 /* 4455 * enum qca_vendor_roam_fail_reasons: Defines the various roam 4456 * fail reasons. This enum value is used in 4457 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON attribute. 4458 * 4459 * @QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED: Roam module in the firmware is not 4460 * able to trigger the scan. 4461 * @QCA_ROAM_FAIL_REASON_NO_AP_FOUND: No roamable APs found during roam scan. 4462 * @QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND: No candidate APs found during roam 4463 * scan. 4464 * @QCA_ROAM_FAIL_REASON_HOST: Roam fail due to disconnect issued from host. 4465 * @QCA_ROAM_FAIL_REASON_AUTH_SEND: Unable to send Authentication frame. 4466 * @QCA_ROAM_FAIL_REASON_AUTH_RECV: Received Authentication frame with error 4467 * status code. 4468 * @QCA_ROAM_FAIL_REASON_NO_AUTH_RESP: Authentication frame not received. 4469 * @QCA_ROAM_FAIL_REASON_REASSOC_SEND: Unable to send Reassociation Request 4470 * frame. 4471 * @QCA_ROAM_FAIL_REASON_REASSOC_RECV: Received Reassociation Response frame 4472 * with error status code. 4473 * @QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP: Reassociation Response frame not 4474 * received. 4475 * @QCA_ROAM_FAIL_REASON_SCAN_FAIL: Scan module not able to start scan. 4476 * @QCA_ROAM_FAIL_REASON_AUTH_NO_ACK: No ACK is received for Authentication 4477 * frame. 4478 * @QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP: Authentication frame is dropped 4479 * internally before transmission. 4480 * @QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK: No ACK is received for Reassociation 4481 * Request frame. 4482 * @QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP: Reassociation Request frame is 4483 * dropped internally. 4484 * @QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT: EAPOL-Key M1 is not received and 4485 * times out. 4486 * @QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND: Unable to send EAPOL-Key M2 frame. 4487 * @QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP: EAPOL-Key M2 frame dropped 4488 * internally. 4489 * @QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK: No ACK is received for EAPOL-Key 4490 * M2 frame. 4491 * @QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT: EAPOL-Key M3 frame is not received. 4492 * @QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND: Unable to send EAPOL-Key M4 frame. 4493 * @QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP: EAPOL-Key M4 frame dropped 4494 * internally. 4495 * @QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK: No ACK is received for EAPOL-Key M4 4496 * frame. 4497 * @QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS: Roam scan is not 4498 * started for final beacon miss case. 4499 * @QCA_ROAM_FAIL_REASON_DISCONNECT: Deauthentication or Disassociation frame 4500 * received from the AP during roaming handoff. 4501 * @QCA_ROAM_FAIL_REASON_RESUME_ABORT: Firmware roams to the AP when the Apps 4502 * or host is suspended and gives the indication of the last roamed AP only 4503 * when the Apps is resumed. If the Apps is resumed while the roaming is in 4504 * progress, this ongoing roaming is aborted and the last roamed AP is 4505 * indicated to host. 4506 * @QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID: WPA3-SAE invalid PMKID. 4507 * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT: WPA3-SAE pre-authentication times 4508 * out. 4509 * @QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL: WPA3-SAE pre-authentication fails. 4510 */ 4511 enum qca_vendor_roam_fail_reasons { 4512 QCA_ROAM_FAIL_REASON_NONE = 0, 4513 QCA_ROAM_FAIL_REASON_SCAN_NOT_ALLOWED = 1, 4514 QCA_ROAM_FAIL_REASON_NO_AP_FOUND = 2, 4515 QCA_ROAM_FAIL_REASON_NO_CAND_AP_FOUND = 3, 4516 QCA_ROAM_FAIL_REASON_HOST = 4, 4517 QCA_ROAM_FAIL_REASON_AUTH_SEND = 5, 4518 QCA_ROAM_FAIL_REASON_AUTH_RECV = 6, 4519 QCA_ROAM_FAIL_REASON_NO_AUTH_RESP = 7, 4520 QCA_ROAM_FAIL_REASON_REASSOC_SEND = 8, 4521 QCA_ROAM_FAIL_REASON_REASSOC_RECV = 9, 4522 QCA_ROAM_FAIL_REASON_NO_REASSOC_RESP = 10, 4523 QCA_ROAM_FAIL_REASON_SCAN_FAIL = 11, 4524 QCA_ROAM_FAIL_REASON_AUTH_NO_ACK = 12, 4525 QCA_ROAM_FAIL_REASON_AUTH_INTERNAL_DROP = 13, 4526 QCA_ROAM_FAIL_REASON_REASSOC_NO_ACK = 14, 4527 QCA_ROAM_FAIL_REASON_REASSOC_INTERNAL_DROP = 15, 4528 QCA_ROAM_FAIL_REASON_EAPOL_M1_TIMEOUT = 16, 4529 QCA_ROAM_FAIL_REASON_EAPOL_M2_SEND = 17, 4530 QCA_ROAM_FAIL_REASON_EAPOL_M2_INTERNAL_DROP = 18, 4531 QCA_ROAM_FAIL_REASON_EAPOL_M2_NO_ACK = 19, 4532 QCA_ROAM_FAIL_REASON_EAPOL_M3_TIMEOUT = 20, 4533 QCA_ROAM_FAIL_REASON_EAPOL_M4_SEND = 21, 4534 QCA_ROAM_FAIL_REASON_EAPOL_M4_INTERNAL_DROP = 22, 4535 QCA_ROAM_FAIL_REASON_EAPOL_M4_NO_ACK = 23, 4536 QCA_ROAM_FAIL_REASON_NO_SCAN_FOR_FINAL_BEACON_MISS = 24, 4537 QCA_ROAM_FAIL_REASON_DISCONNECT = 25, 4538 QCA_ROAM_FAIL_REASON_RESUME_ABORT = 26, 4539 QCA_ROAM_FAIL_REASON_SAE_INVALID_PMKID = 27, 4540 QCA_ROAM_FAIL_REASON_SAE_PREAUTH_TIMEOUT = 28, 4541 QCA_ROAM_FAIL_REASON_SAE_PREAUTH_FAIL = 29, 4542 }; 4543 4544 /* 4545 * enum qca_vendor_roam_invoke_fail_reasons: Defines the various roam 4546 * invoke fail reasons. This enum value is used in 4547 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON attribute. 4548 * 4549 * @QCA_ROAM_INVOKE_STATUS_IFACE_INVALID: Invalid interface ID is passed 4550 * in roam invoke command. 4551 * @QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE: Roam offload in firmware is not 4552 * enabled. 4553 * @QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID: Connected AP profile SSID 4554 * length is invalid. 4555 * @QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW: Firmware internal roaming is already 4556 * in progress. 4557 * @QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP: Host sends the Beacon/Probe Response 4558 * of the AP in the roam invoke command to firmware. This reason is sent by the 4559 * firmware when the given AP is configured to be ignored or SSID/security 4560 * does not match. 4561 * @QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL: Roam handoff failed because of 4562 * firmware internal reasons. 4563 * @QCA_ROAM_INVOKE_STATUS_DISALLOW: Roam invoke trigger is not enabled. 4564 * @QCA_ROAM_INVOKE_STATUS_SCAN_FAIL: Scan start fail for roam invoke. 4565 * @QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL: Roam handoff start fail. 4566 * @QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS: Roam invoke parameters are invalid. 4567 * @QCA_ROAM_INVOKE_STATUS_NO_CAND_AP: No candidate AP found to roam to. 4568 * @QCA_ROAM_INVOKE_STATUS_ROAM_FAIL: Roam handoff failed. 4569 */ 4570 enum qca_vendor_roam_invoke_fail_reasons { 4571 QCA_ROAM_INVOKE_STATUS_NONE = 0, 4572 QCA_ROAM_INVOKE_STATUS_IFACE_INVALID = 1, 4573 QCA_ROAM_INVOKE_STATUS_OFFLOAD_DISABLE = 2, 4574 QCA_ROAM_INVOKE_STATUS_AP_SSID_LENGTH_INVALID = 3, 4575 QCA_ROAM_INVOKE_STATUS_ROAM_DISALLOW = 4, 4576 QCA_ROAM_INVOKE_STATUS_NON_ROAMABLE_AP = 5, 4577 QCA_ROAM_INVOKE_STATUS_ROAM_INTERNAL_FAIL = 6, 4578 QCA_ROAM_INVOKE_STATUS_DISALLOW = 7, 4579 QCA_ROAM_INVOKE_STATUS_SCAN_FAIL = 8, 4580 QCA_ROAM_INVOKE_STATUS_START_ROAM_FAIL = 9, 4581 QCA_ROAM_INVOKE_STATUS_INVALID_PARAMS = 10, 4582 QCA_ROAM_INVOKE_STATUS_NO_CAND_AP = 11, 4583 QCA_ROAM_INVOKE_STATUS_ROAM_FAIL = 12, 4584 4585 }; 4586 4587 /** 4588 * enum qca_vendor_attr_roam_candidate_selection_criteria: 4589 * 4590 * Each attribute carries a weightage in percentage (%). 4591 * 4592 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI: Unsigned 8-bit value. 4593 * Represents the weightage to be given for the RSSI selection 4594 * criteria among other parameters. 4595 * 4596 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE: Unsigned 8-bit value. 4597 * Represents the weightage to be given for the rate selection 4598 * criteria among other parameters. 4599 * 4600 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW: Unsigned 8-bit value. 4601 * Represents the weightage to be given for the band width selection 4602 * criteria among other parameters. 4603 * 4604 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND: Unsigned 8-bit value. 4605 * Represents the weightage to be given for the band selection 4606 * criteria among other parameters. 4607 * 4608 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS: Unsigned 8-bit value. 4609 * Represents the weightage to be given for the NSS selection 4610 * criteria among other parameters. 4611 * 4612 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION: Unsigned 8-bit value. 4613 * Represents the weightage to be given for the channel congestion 4614 * selection criteria among other parameters. 4615 * 4616 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING: Unsigned 8-bit value. 4617 * Represents the weightage to be given for the beamforming selection 4618 * criteria among other parameters. 4619 * 4620 * @QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN: Unsigned 8-bit value. 4621 * Represents the weightage to be given for the OCE selection 4622 * criteria among other parameters. 4623 */ 4624 enum qca_vendor_attr_roam_candidate_selection_criteria { 4625 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_RSSI = 1, 4626 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE = 2, 4627 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BW = 3, 4628 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BAND = 4, 4629 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_NSS = 5, 4630 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_CHAN_CONGESTION = 6, 4631 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_BEAMFORMING = 7, 4632 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_SCORE_OCE_WAN = 8, 4633 4634 /* keep last */ 4635 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST, 4636 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_MAX = 4637 QCA_ATTR_ROAM_CAND_SEL_CRITERIA_RATE_AFTER_LAST - 1, 4638 }; 4639 4640 /** 4641 * enum qca_vendor_attr_roam_control - Attributes to carry roam configuration 4642 * The following attributes are used to set/get/clear the respective 4643 * configurations to/from the driver. 4644 * For the get, the attribute for the configuration to be queried shall 4645 * carry any of its acceptable values to the driver. In return, the driver 4646 * shall send the configured values within the same attribute to the user 4647 * space. 4648 * 4649 * @QCA_ATTR_ROAM_CONTROL_ENABLE: Unsigned 8-bit value. 4650 * Signifies to enable/disable roam control in driver. 4651 * 1-enable, 0-disable 4652 * Enable: Mandates the driver to do the further roams using the 4653 * configuration parameters set through 4654 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. 4655 * Disable: Disables the driver/firmware roaming triggered through 4656 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET. Further roaming is 4657 * expected to continue with the default configurations. 4658 * 4659 * @QCA_ATTR_ROAM_CONTROL_STATUS: Unsigned 8-bit value. 4660 * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET. 4661 * Roam control status is obtained through this attribute. 4662 * 4663 * @QCA_ATTR_ROAM_CONTROL_CLEAR_ALL: Flag attribute to indicate the 4664 * complete config set through QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET 4665 * is to be cleared in the driver. 4666 * This is used along with QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR 4667 * and shall be ignored if used with other sub commands. 4668 * If this attribute is specified along with subcmd 4669 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR, the driver shall ignore 4670 * all other attributes, if there are any. 4671 * If this attribute is not specified when the subcmd 4672 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR is sent, the driver shall 4673 * clear the data corresponding to the attributes specified. 4674 * 4675 * @QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME: Nested attribute to carry the 4676 * list of frequencies and its type, represented by 4677 * enum qca_vendor_attr_scan_freq_list_scheme. 4678 * Frequency list and its type are mandatory for this attribute to set 4679 * the frequencies. 4680 * Frequency type is mandatory for this attribute to get the frequencies 4681 * and the frequency list is obtained through 4682 * QCA_ATTR_ROAM_CONTROL_SCAN_FREQ_LIST. 4683 * Frequency list type is mandatory for this attribute to clear the 4684 * frequencies. 4685 * 4686 * @QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD: Unsigned 32-bit value. 4687 * Carries the value of scan period in seconds to set. 4688 * The value of scan period is obtained with the same attribute for get. 4689 * Clears the scan period in the driver when specified with clear command. 4690 * Scan period is the idle time in seconds between each subsequent 4691 * channel scans. 4692 * 4693 * @QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD: Unsigned 32-bit value. 4694 * Carries the value of full scan period in seconds to set. 4695 * The value of full scan period is obtained with the same attribute for 4696 * get. 4697 * Clears the full scan period in the driver when specified with clear 4698 * command. Full scan period is the idle period in seconds between two 4699 * successive full channel roam scans. 4700 * 4701 * @QCA_ATTR_ROAM_CONTROL_TRIGGERS: Unsigned 32-bit value. 4702 * Carries a bitmap of the roam triggers specified in 4703 * enum qca_vendor_roam_triggers. 4704 * The driver shall enable roaming by enabling corresponding roam triggers 4705 * based on the trigger bits sent with this attribute. 4706 * If this attribute is not configured, the driver shall proceed with 4707 * default behavior. 4708 * The bitmap configured is obtained with the same attribute for get. 4709 * Clears the bitmap configured in driver when specified with clear 4710 * command. 4711 * 4712 * @QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA: Nested attribute signifying the 4713 * weightage in percentage (%) to be given for each selection criteria. 4714 * Different roam candidate selection criteria are represented by 4715 * enum qca_vendor_attr_roam_candidate_selection_criteria. 4716 * The driver shall select the roam candidate based on corresponding 4717 * candidate selection scores sent. 4718 * 4719 * An empty nested attribute is used to indicate that no specific 4720 * preference score/criteria is configured (i.e., to disable this mechanism 4721 * in the set case and to show that the mechanism is disabled in the get 4722 * case). 4723 * 4724 * Userspace can send multiple attributes out of this enum to the driver. 4725 * Since this attribute represents the weight/percentage of preference for 4726 * the respective selection criteria, it is preferred to configure 100% 4727 * total weightage. The value in each attribute or cumulative weight of the 4728 * values in all the nested attributes should not exceed 100%. The driver 4729 * shall reject such configuration. 4730 * 4731 * If the weights configured through this attribute are less than 100%, 4732 * the driver shall honor the weights (x%) passed for the corresponding 4733 * selection criteria and choose/distribute rest of the weight (100-x)% 4734 * for the other selection criteria, based on its internal logic. 4735 * 4736 * The selection criteria configured is obtained with the same 4737 * attribute for get. 4738 * 4739 * Clears the selection criteria configured in the driver when specified 4740 * with clear command. 4741 * 4742 * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME: Unsigned 32-bit value. 4743 * Represents value of the scan frequency scheme from enum 4744 * qca_roam_scan_scheme. 4745 * It's an optional attribute. If this attribute is not configured, the 4746 * driver shall proceed with default behavior. 4747 * 4748 * @QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD: Signed 32-bit value in dBm, 4749 * signifying the RSSI threshold of the current connected AP, indicating 4750 * the driver to trigger roam only when the current connected AP's RSSI 4751 * is less than this threshold. 4752 * 4753 * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD: Signed 32-bit value in dBm, 4754 * signifying the RSSI threshold of the candidate AP, indicating 4755 * the driver to trigger roam only to the candidate AP with RSSI 4756 * better than this threshold. If RSSI thresholds for candidate APs found 4757 * in the 2.4 GHz, 5 GHz, and 6 GHz bands are configured separately using 4758 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ, 4759 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ, and/or 4760 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ, those values will 4761 * take precedence over the value configured using the 4762 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute. 4763 * 4764 * @QCA_ATTR_ROAM_CONTROL_USER_REASON: Unsigned 32-bit value. Represents the 4765 * user defined reason code to be sent to the AP in response to AP's 4766 * request to trigger the roam if the roaming cannot be triggered. 4767 * Applies to all the scenarios of AP assisted roaming (e.g., BTM). 4768 * 4769 * @QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS: Unsigned 32-bit value. 4770 * Carries a bitmap of the roam triggers specified in 4771 * enum qca_vendor_roam_triggers. 4772 * Represents the roam triggers for which the specific scan scheme from 4773 * enum qca_roam_scan_scheme has to be applied. 4774 * It's an optional attribute. If this attribute is not configured, but 4775 * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is specified, the scan scheme 4776 * specified through QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME is applicable for 4777 * all the roams. 4778 * If both QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME and 4779 * QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS are not specified, the 4780 * driver shall proceed with the default behavior. 4781 * 4782 * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ: Signed 32-bit value 4783 * in dBm, signifying the RSSI threshold of the candidate AP found in the 4784 * 2.4 GHz band. The driver/firmware shall trigger roaming to the candidate 4785 * AP found in the 2.4 GHz band only if its RSSI value is better than this 4786 * threshold. Optional attribute. If this attribute is not included, the 4787 * threshold value specified by the 4788 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. 4789 * 4790 * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ: Signed 32-bit value in 4791 * dBm, signifying the RSSI threshold of the candidate AP found in the 5 4792 * GHz band. The driver/firmware shall trigger roaming to the candidate AP 4793 * found in the 5 GHz band only if its RSSI value is better than this 4794 * threshold. Optional attribute. If this attribute is not included, the 4795 * threshold value specified by tge 4796 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. 4797 * 4798 * @QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ: Signed 32-bit value in 4799 * dBm, signifying the RSSI threshold of the candidate AP found in the 6 4800 * GHz band. The driver/firmware shall trigger roaming to the candidate AP 4801 * found in the 6 GHz band only if its RSSI value is better than this 4802 * threshold. Optional attribute. If this attribute is not included, the 4803 * threshold value specified by the 4804 * QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD attribute shall be used. 4805 * 4806 * @QCA_ATTR_ROAM_CONTROL_BAND_MASK: Unsigned 32-bit value. 4807 * Carries bitmask value of bits from &enum qca_set_band and represents 4808 * all the bands in which roaming is allowed. The configuration is valid 4809 * until next disconnection. If this attribute is not present, the 4810 * existing configuration shall be used. By default, roaming is allowed on 4811 * all bands supported by the local device. When the value is set to 4812 * %QCA_SETBAND_AUTO, all supported bands shall be enabled. 4813 * 4814 * @QCA_ATTR_ROAM_CONTROL_ACTIVE_CH_DWELL_TIME: u16 value in milliseconds. 4815 * Optional parameter. Scan dwell time for active channels in the 2.4/5 GHz 4816 * bands. If this attribute is not configured, the driver shall proceed 4817 * with default behavior. 4818 * 4819 * @QCA_ATTR_ROAM_CONTROL_PASSIVE_CH_DWELL_TIME: u16 value in milliseconds. 4820 * Optional parameter. Scan dwell time for passive channels in the 5 GHz 4821 * band. If this attribute is not configured, the driver shall proceed with 4822 * default behavior. 4823 * 4824 * @QCA_ATTR_ROAM_CONTROL_HOME_CHANNEL_TIME: u16 value in milliseconds. 4825 * Optional parameter. The minimum duration to stay on the connected AP 4826 * channel during the channel scanning. If this attribute is not 4827 * configured, the driver shall proceed with default behavior. 4828 * 4829 * @QCA_ATTR_ROAM_CONTROL_MAXIMUM_AWAY_TIME: u16 value in milliseconds. 4830 * Optional parameter. The maximum duration for which the radio can scan 4831 * foreign channels consecutively without coming back to home channel. If 4832 * this attribute is not configured, the driver shall proceed with default 4833 * behavior. 4834 * 4835 * @QCA_ATTR_ROAM_CONTROL_SCAN_6G_PSC_DWELL_TIME: u16 value in milliseconds. 4836 * Optional parameter. Scan dwell time for 6G Preferred Scanning Channels. 4837 * If this attribute is not configured, the driver shall proceed with 4838 * default behavior. 4839 * 4840 * @QCA_ATTR_ROAM_CONTROL_SCAN_6G_NON_PSC_DWELL_TIME: u16 value in milliseconds. 4841 * Optional parameter. Scan dwell time for 6G Non Preferred Scanning 4842 * Channels. If this attribute is not configured, the driver shall proceed 4843 * with default behavior. 4844 */ 4845 enum qca_vendor_attr_roam_control { 4846 QCA_ATTR_ROAM_CONTROL_ENABLE = 1, 4847 QCA_ATTR_ROAM_CONTROL_STATUS = 2, 4848 QCA_ATTR_ROAM_CONTROL_CLEAR_ALL = 3, 4849 QCA_ATTR_ROAM_CONTROL_FREQ_LIST_SCHEME= 4, 4850 QCA_ATTR_ROAM_CONTROL_SCAN_PERIOD = 5, 4851 QCA_ATTR_ROAM_CONTROL_FULL_SCAN_PERIOD = 6, 4852 QCA_ATTR_ROAM_CONTROL_TRIGGERS = 7, 4853 QCA_ATTR_ROAM_CONTROL_SELECTION_CRITERIA = 8, 4854 QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME = 9, 4855 QCA_ATTR_ROAM_CONTROL_CONNECTED_RSSI_THRESHOLD = 10, 4856 QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD = 11, 4857 QCA_ATTR_ROAM_CONTROL_USER_REASON = 12, 4858 QCA_ATTR_ROAM_CONTROL_SCAN_SCHEME_TRIGGERS = 13, 4859 QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_2P4GHZ = 14, 4860 QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_5GHZ = 15, 4861 QCA_ATTR_ROAM_CONTROL_CANDIDATE_RSSI_THRESHOLD_6GHZ = 16, 4862 QCA_ATTR_ROAM_CONTROL_BAND_MASK = 17, 4863 QCA_ATTR_ROAM_CONTROL_ACTIVE_CH_DWELL_TIME = 18, 4864 QCA_ATTR_ROAM_CONTROL_PASSIVE_CH_DWELL_TIME = 19, 4865 QCA_ATTR_ROAM_CONTROL_HOME_CHANNEL_TIME = 20, 4866 QCA_ATTR_ROAM_CONTROL_MAXIMUM_AWAY_TIME = 21, 4867 QCA_ATTR_ROAM_CONTROL_SCAN_6G_PSC_DWELL_TIME = 22, 4868 QCA_ATTR_ROAM_CONTROL_SCAN_6G_NON_PSC_DWELL_TIME = 23, 4869 4870 /* keep last */ 4871 QCA_ATTR_ROAM_CONTROL_AFTER_LAST, 4872 QCA_ATTR_ROAM_CONTROL_MAX = 4873 QCA_ATTR_ROAM_CONTROL_AFTER_LAST - 1, 4874 }; 4875 4876 /* 4877 * enum qca_wlan_vendor_attr_roaming_config_params: Attributes for data used by 4878 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. 4879 * 4880 * @QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD: Unsigned 32-bit value. 4881 * Represents the different roam sub commands referred by 4882 * enum qca_wlan_vendor_roaming_subcmd. 4883 * 4884 * @QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID: Unsigned 32-bit value. 4885 * Represents the Request ID for the specific set of commands. 4886 * This also helps to map specific set of commands to the respective 4887 * ID / client. e.g., helps to identify the user entity configuring the 4888 * ignored BSSIDs and accordingly clear the respective ones with the 4889 * matching ID. 4890 * 4891 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS: Unsigned 4892 * 32-bit value.Represents the number of whitelist SSIDs configured. 4893 * 4894 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST: Nested attribute 4895 * to carry the list of Whitelist SSIDs. 4896 * 4897 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID: SSID (binary attribute, 4898 * 0..32 octets). Represents the white list SSID. Whitelist SSIDs 4899 * represent the list of SSIDs to which the firmware/driver can consider 4900 * to roam to. 4901 * 4902 * The following PARAM_A_BAND_XX attributes are applied to 5GHz BSSIDs when 4903 * comparing with a 2.4GHz BSSID. They are not applied when comparing two 4904 * 5GHz BSSIDs.The following attributes are set through the Roaming SUBCMD - 4905 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS. 4906 * 4907 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD: Signed 32-bit 4908 * value, RSSI threshold above which 5GHz RSSI is favored. 4909 * 4910 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD: Signed 32-bit 4911 * value, RSSI threshold below which 5GHz RSSI is penalized. 4912 * 4913 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR: Unsigned 32-bit 4914 * value, factor by which 5GHz RSSI is boosted. 4915 * boost=(RSSI_measured-5GHz_boost_threshold)*5GHz_boost_factor 4916 * 4917 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR: Unsigned 32-bit 4918 * value, factor by which 5GHz RSSI is penalized. 4919 * penalty=(5GHz_penalty_threshold-RSSI_measured)*5GHz_penalty_factor 4920 * 4921 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST: Unsigned 32-bit 4922 * value, maximum boost that can be applied to a 5GHz RSSI. 4923 * 4924 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS: Unsigned 32-bit 4925 * value, boost applied to current BSSID to ensure the currently 4926 * associated BSSID is favored so as to prevent ping-pong situations. 4927 * 4928 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER: Signed 32-bit 4929 * value, RSSI below which "Alert" roam is enabled. 4930 * "Alert" mode roaming - firmware is "urgently" hunting for another BSSID 4931 * because the RSSI is low, or because many successive beacons have been 4932 * lost or other bad link conditions. 4933 * 4934 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE: Unsigned 32-bit 4935 * value. 1-Enable, 0-Disable. Represents "Lazy" mode, where 4936 * firmware is hunting for a better BSSID or white listed SSID even though 4937 * the RSSI of the link is good. The parameters enabling the roaming are 4938 * configured through the PARAM_A_BAND_XX attrbutes. 4939 * 4940 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS: Nested attribute, 4941 * represents the BSSIDs preferred over others while evaluating them 4942 * for the roaming. 4943 * 4944 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID: Unsigned 4945 * 32-bit value. Represents the number of preferred BSSIDs set. 4946 * 4947 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID: 6-byte MAC 4948 * address representing the BSSID to be preferred. 4949 * 4950 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER: Signed 4951 * 32-bit value, representing the modifier to be applied to the RSSI of 4952 * the BSSID for the purpose of comparing it with other roam candidate. 4953 * 4954 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS: Nested attribute, 4955 * represents the BSSIDs to get ignored for roaming. 4956 * 4957 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID: Unsigned 4958 * 32-bit value, represents the number of ignored BSSIDs. 4959 * 4960 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID: 6-byte MAC 4961 * address representing the ignored BSSID. 4962 * 4963 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT: Flag attribute, 4964 * indicates this request to ignore the BSSID as a hint to the driver. The 4965 * driver can select this BSSID in the worst case (when no other BSSIDs are 4966 * better). 4967 * 4968 * @QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL: Nested attribute to 4969 * set/get/clear the roam control config as 4970 * defined @enum qca_vendor_attr_roam_control. 4971 */ 4972 enum qca_wlan_vendor_attr_roaming_config_params { 4973 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, 4974 4975 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, 4976 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, 4977 4978 /* Attributes for wifi_set_ssid_white_list */ 4979 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, 4980 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, 4981 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, 4982 4983 /* Attributes for set_roam_params */ 4984 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, 4985 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, 4986 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, 4987 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, 4988 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, 4989 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, 4990 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, 4991 4992 /* Attribute for set_lazy_roam */ 4993 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, 4994 4995 /* Attribute for set_lazy_roam with preferences */ 4996 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, 4997 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, 4998 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, 4999 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, 5000 5001 /* Attribute for setting ignored BSSID parameters */ 5002 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, 5003 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, 5004 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, 5005 /* Flag attribute indicates this entry as a hint */ 5006 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21, 5007 5008 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL = 22, 5009 5010 /* keep last */ 5011 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, 5012 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = 5013 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, 5014 }; 5015 5016 /* 5017 * enum qca_wlan_vendor_roaming_subcmd: Referred by 5018 * QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD. 5019 * 5020 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST: Sub command to 5021 * configure the white list SSIDs. These are configured through 5022 * the following attributes. 5023 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS, 5024 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST, 5025 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID 5026 * 5027 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS: Sub command to 5028 * configure the Roam params. These parameters are evaluated on the GScan 5029 * results. Refers the attributes PARAM_A_BAND_XX above to configure the 5030 * params. 5031 * 5032 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM: Sets the Lazy roam. Uses 5033 * the attribute QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE 5034 * to enable/disable Lazy roam. 5035 * 5036 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS: Sets the BSSID 5037 * preference. Contains the attribute 5038 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS to set the BSSID 5039 * preference. 5040 * 5041 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID: Sets the list of BSSIDs 5042 * to ignore in roaming decision. Uses 5043 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS to set the list. 5044 * 5045 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET: Command to set the 5046 * roam control config to the driver with the attribute 5047 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. 5048 * 5049 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET: Command to obtain the 5050 * roam control config from driver with the attribute 5051 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. 5052 * For the get, the attribute for the configuration to be queried shall 5053 * carry any of its acceptable value to the driver. In return, the driver 5054 * shall send the configured values within the same attribute to the user 5055 * space. 5056 * 5057 * @QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR: Command to clear the 5058 * roam control config in the driver with the attribute 5059 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_CONTROL. 5060 * The driver shall continue with its default roaming behavior when data 5061 * corresponding to an attribute is cleared. 5062 */ 5063 enum qca_wlan_vendor_roaming_subcmd { 5064 QCA_WLAN_VENDOR_ROAMING_SUBCMD_INVALID = 0, 5065 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SSID_WHITE_LIST = 1, 5066 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2, 5067 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_LAZY_ROAM = 3, 5068 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PREFS = 4, 5069 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BSSID_PARAMS = 5, 5070 QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID = 6, 5071 QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_SET = 7, 5072 QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_GET = 8, 5073 QCA_WLAN_VENDOR_ROAMING_SUBCMD_CONTROL_CLEAR = 9, 5074 }; 5075 5076 enum qca_wlan_vendor_attr_gscan_config_params { 5077 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, 5078 5079 /* Unsigned 32-bit value */ 5080 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, 5081 5082 /* Attributes for data used by 5083 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command. 5084 */ 5085 /* Unsigned 32-bit value */ 5086 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND 5087 = 2, 5088 /* Unsigned 32-bit value */ 5089 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS 5090 = 3, 5091 5092 /* Attributes for input params used by 5093 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command. 5094 */ 5095 5096 /* Unsigned 32-bit value; channel frequency */ 5097 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4, 5098 /* Unsigned 32-bit value; dwell time in ms. */ 5099 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5, 5100 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ 5101 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6, 5102 /* Unsigned 8-bit value; channel class */ 5103 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7, 5104 5105 /* Unsigned 8-bit value; bucket index, 0 based */ 5106 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8, 5107 /* Unsigned 8-bit value; band. */ 5108 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9, 5109 /* Unsigned 32-bit value; desired period, in ms. */ 5110 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10, 5111 /* Unsigned 8-bit value; report events semantics. */ 5112 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, 5113 /* Unsigned 32-bit value. Followed by a nested array of 5114 * GSCAN_CHANNEL_SPEC_* attributes. 5115 */ 5116 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, 5117 5118 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes. 5119 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 5120 */ 5121 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13, 5122 5123 /* Unsigned 32-bit value; base timer period in ms. */ 5124 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, 5125 /* Unsigned 32-bit value; number of APs to store in each scan in the 5126 * BSSID/RSSI history buffer (keep the highest RSSI APs). 5127 */ 5128 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, 5129 /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake 5130 * up AP. 5131 */ 5132 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT 5133 = 16, 5134 5135 /* Unsigned 8-bit value; number of scan bucket specs; followed by a 5136 * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size 5137 * of the array is determined by NUM_BUCKETS. 5138 */ 5139 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, 5140 5141 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes. 5142 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS 5143 */ 5144 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18, 5145 5146 /* Unsigned 8-bit value */ 5147 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH 5148 = 19, 5149 /* Unsigned 32-bit value; maximum number of results to be returned. */ 5150 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX 5151 = 20, 5152 5153 /* An array of 6 x unsigned 8-bit value */ 5154 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21, 5155 /* Signed 32-bit value */ 5156 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, 5157 /* Signed 32-bit value */ 5158 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, 5159 /* Unsigned 32-bit value */ 5160 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, 5161 5162 /* Number of hotlist APs as unsigned 32-bit value, followed by a nested 5163 * array of AP_THRESHOLD_PARAM attributes and values. The size of the 5164 * array is determined by NUM_AP. 5165 */ 5166 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, 5167 5168 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes. 5169 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 5170 */ 5171 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26, 5172 5173 /* Unsigned 32-bit value; number of samples for averaging RSSI. */ 5174 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE 5175 = 27, 5176 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 5177 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE 5178 = 28, 5179 /* Unsigned 32-bit value; number of APs breaching threshold. */ 5180 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, 5181 /* Unsigned 32-bit value; number of APs. Followed by an array of 5182 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. 5183 */ 5184 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, 5185 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 5186 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE 5187 = 31, 5188 /* Unsigned 32-bit value. If max_period is non zero or different than 5189 * period, then this bucket is an exponential backoff bucket. 5190 */ 5191 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32, 5192 /* Unsigned 32-bit value. */ 5193 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33, 5194 /* Unsigned 32-bit value. For exponential back off bucket, number of 5195 * scans to perform for a given period. 5196 */ 5197 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34, 5198 /* Unsigned 8-bit value; in number of scans, wake up AP after these 5199 * many scans. 5200 */ 5201 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS 5202 = 35, 5203 5204 /* Attributes for data used by 5205 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command. 5206 */ 5207 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ 5208 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE 5209 = 36, 5210 /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a 5211 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The 5212 * size of the array is determined by NUM_SSID. 5213 */ 5214 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, 5215 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_* 5216 * attributes. 5217 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID 5218 */ 5219 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38, 5220 5221 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 5222 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39, 5223 /* Unsigned 8-bit value */ 5224 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40, 5225 /* Signed 32-bit value */ 5226 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, 5227 /* Signed 32-bit value */ 5228 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, 5229 /* Unsigned 32-bit value; a bitmask with additional gscan config flag. 5230 */ 5231 QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43, 5232 5233 /* keep last */ 5234 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, 5235 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX = 5236 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, 5237 }; 5238 5239 enum qca_wlan_vendor_attr_gscan_results { 5240 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0, 5241 5242 /* Unsigned 32-bit value; must match the request Id supplied by 5243 * Wi-Fi HAL in the corresponding subcmd NL msg. 5244 */ 5245 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1, 5246 5247 /* Unsigned 32-bit value; used to indicate the status response from 5248 * firmware/driver for the vendor sub-command. 5249 */ 5250 QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2, 5251 5252 /* GSCAN Valid Channels attributes */ 5253 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ 5254 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3, 5255 /* An array of NUM_CHANNELS x unsigned 32-bit value integers 5256 * representing channel numbers. 5257 */ 5258 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4, 5259 5260 /* GSCAN Capabilities attributes */ 5261 /* Unsigned 32-bit value */ 5262 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, 5263 /* Unsigned 32-bit value */ 5264 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, 5265 /* Unsigned 32-bit value */ 5266 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN 5267 = 7, 5268 /* Unsigned 32-bit value */ 5269 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE 5270 = 8, 5271 /* Signed 32-bit value */ 5272 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD 5273 = 9, 5274 /* Unsigned 32-bit value */ 5275 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, 5276 /* Unsigned 32-bit value */ 5277 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS 5278 = 11, 5279 /* Unsigned 32-bit value */ 5280 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES 5281 = 12, 5282 5283 /* GSCAN Attributes used with 5284 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command. 5285 */ 5286 5287 /* Unsigned 32-bit value */ 5288 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, 5289 5290 /* GSCAN attributes used with 5291 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command. 5292 */ 5293 5294 /* An array of NUM_RESULTS_AVAILABLE x 5295 * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_* 5296 */ 5297 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14, 5298 5299 /* Unsigned 64-bit value; age of sample at the time of retrieval */ 5300 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, 5301 /* 33 x unsigned 8-bit value; NULL terminated SSID */ 5302 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16, 5303 /* An array of 6 x unsigned 8-bit value */ 5304 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17, 5305 /* Unsigned 32-bit value; channel frequency in MHz */ 5306 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, 5307 /* Signed 32-bit value */ 5308 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19, 5309 /* Unsigned 32-bit value */ 5310 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20, 5311 /* Unsigned 32-bit value */ 5312 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, 5313 /* Unsigned 16-bit value */ 5314 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, 5315 /* Unsigned 16-bit value */ 5316 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, 5317 /* Unsigned 32-bit value; size of the IE DATA blob */ 5318 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, 5319 /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the 5320 * information elements found in the beacon; this data should be a 5321 * packed list of wifi_information_element objects, one after the 5322 * other. 5323 */ 5324 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, 5325 5326 /* Unsigned 8-bit value; set by driver to indicate more scan results are 5327 * available. 5328 */ 5329 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, 5330 5331 /* GSCAN attributes for 5332 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command. 5333 */ 5334 /* Unsigned 8-bit value */ 5335 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27, 5336 /* Unsigned 32-bit value */ 5337 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28, 5338 5339 /* GSCAN attributes for 5340 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command. 5341 */ 5342 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 5343 * to indicate number of results. 5344 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 5345 * list of results. 5346 */ 5347 5348 /* GSCAN attributes for 5349 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command. 5350 */ 5351 /* An array of 6 x unsigned 8-bit value */ 5352 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, 5353 /* Unsigned 32-bit value */ 5354 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL 5355 = 30, 5356 /* Unsigned 32-bit value. */ 5357 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI 5358 = 31, 5359 /* A nested array of signed 32-bit RSSI values. Size of the array is 5360 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. 5361 */ 5362 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST 5363 = 32, 5364 5365 /* GSCAN attributes used with 5366 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command. 5367 */ 5368 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 5369 * to indicate number of gscan cached results returned. 5370 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate 5371 * the list of gscan cached results. 5372 */ 5373 5374 /* An array of NUM_RESULTS_AVAILABLE x 5375 * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_* 5376 */ 5377 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33, 5378 /* Unsigned 32-bit value; a unique identifier for the scan unit. */ 5379 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34, 5380 /* Unsigned 32-bit value; a bitmask w/additional information about scan. 5381 */ 5382 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35, 5383 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 5384 * to indicate number of wifi scan results/bssids retrieved by the scan. 5385 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 5386 * list of wifi scan results returned for each cached result block. 5387 */ 5388 5389 /* GSCAN attributes for 5390 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. 5391 */ 5392 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for 5393 * number of results. 5394 * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 5395 * list of wifi scan results returned for each 5396 * wifi_passpoint_match_result block. 5397 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE. 5398 */ 5399 5400 /* GSCAN attributes for 5401 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. 5402 */ 5403 /* Unsigned 32-bit value */ 5404 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES 5405 = 36, 5406 /* A nested array of 5407 * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_* 5408 * attributes. Array size = 5409 * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. 5410 */ 5411 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, 5412 5413 /* Unsigned 32-bit value; network block id for the matched network */ 5414 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, 5415 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 5416 * list of wifi scan results returned for each 5417 * wifi_passpoint_match_result block. 5418 */ 5419 /* Unsigned 32-bit value */ 5420 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, 5421 /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; 5422 * ANQP data in the information_element format. 5423 */ 5424 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, 5425 5426 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 5427 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, 5428 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 5429 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, 5430 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 5431 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID 5432 = 43, 5433 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 5434 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID 5435 = 44, 5436 5437 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45, 5438 5439 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. 5440 * This is used to limit the maximum number of BSSIDs while sending 5441 * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with subcmd 5442 * QCA_WLAN_VENDOR_ROAMING_SUBCMD_SET_BLACKLIST_BSSID and attribute 5443 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID. 5444 */ 5445 QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, 5446 5447 /* keep last */ 5448 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST, 5449 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX = 5450 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1, 5451 }; 5452 5453 enum qca_wlan_vendor_attr_pno_config_params { 5454 QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, 5455 /* Attributes for data used by 5456 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. 5457 */ 5458 /* Unsigned 32-bit value */ 5459 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, 5460 /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* 5461 * attributes. Array size = 5462 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. 5463 */ 5464 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, 5465 5466 /* Unsigned 32-bit value */ 5467 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, 5468 /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded 5469 * realm, 0 if unspecified. 5470 */ 5471 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, 5472 /* An array of 16 x unsigned 32-bit value; roaming consortium ids to 5473 * match, 0 if unspecified. 5474 */ 5475 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, 5476 /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if 5477 * unspecified. 5478 */ 5479 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, 5480 5481 /* Attributes for data used by 5482 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. 5483 */ 5484 /* Unsigned 32-bit value */ 5485 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, 5486 /* Array of nested 5487 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* 5488 * attributes. Array size = 5489 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS. 5490 */ 5491 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, 5492 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 5493 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, 5494 /* Signed 8-bit value; threshold for considering this SSID as found, 5495 * required granularity for this threshold is 4 dBm to 8 dBm. 5496 */ 5497 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD 5498 = 10, 5499 /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */ 5500 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, 5501 /* Unsigned 8-bit value; auth bit field for matching WPA IE */ 5502 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, 5503 /* Unsigned 8-bit to indicate ePNO type; 5504 * It takes values from qca_wlan_epno_type 5505 */ 5506 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, 5507 5508 /* Nested attribute to send the channel list */ 5509 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, 5510 5511 /* Unsigned 32-bit value; indicates the interval between PNO scan 5512 * cycles in msec. 5513 */ 5514 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, 5515 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, 5516 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, 5517 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, 5518 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, 5519 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, 5520 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, 5521 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, 5522 /* Unsigned 32-bit value, representing the PNO Request ID */ 5523 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, 5524 5525 /* keep last */ 5526 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, 5527 QCA_WLAN_VENDOR_ATTR_PNO_MAX = 5528 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, 5529 }; 5530 5531 /** 5532 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why 5533 * the ACS has to be triggered. These values are used by 5534 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and 5535 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON 5536 */ 5537 enum qca_wlan_vendor_acs_select_reason { 5538 /* Represents the reason that the ACS triggered during the AP start */ 5539 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, 5540 /* Represents the reason that DFS found with the current channel */ 5541 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, 5542 /* Represents the reason that LTE co-exist in the current band. */ 5543 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, 5544 /* Represents the reason that generic, uncategorized interference has 5545 * been found in the current channel. 5546 */ 5547 QCA_WLAN_VENDOR_ACS_SELECT_REASON_GENERIC_INTERFERENCE, 5548 /* Represents the reason that excessive 802.11 interference has been 5549 * found in the current channel. 5550 */ 5551 QCA_WLAN_VENDOR_ACS_SELECT_REASON_80211_INTERFERENCE, 5552 /* Represents the reason that generic Continuous Wave (CW) interference 5553 * has been found in the current channel. 5554 */ 5555 QCA_WLAN_VENDOR_ACS_SELECT_REASON_CW_INTERFERENCE, 5556 /* Represents the reason that Microwave Oven (MWO) interference has been 5557 * found in the current channel. 5558 */ 5559 QCA_WLAN_VENDOR_ACS_SELECT_REASON_MWO_INTERFERENCE, 5560 /* Represents the reason that generic Frequency-Hopping Spread Spectrum 5561 * (FHSS) interference has been found in the current channel. This may 5562 * include 802.11 waveforms. 5563 */ 5564 QCA_WLAN_VENDOR_ACS_SELECT_REASON_FHSS_INTERFERENCE, 5565 /* Represents the reason that non-802.11 generic Frequency-Hopping 5566 * Spread Spectrum (FHSS) interference has been found in the current 5567 * channel. 5568 */ 5569 QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_FHSS_INTERFERENCE, 5570 /* Represents the reason that generic Wideband (WB) interference has 5571 * been found in the current channel. This may include 802.11 waveforms. 5572 */ 5573 QCA_WLAN_VENDOR_ACS_SELECT_REASON_WB_INTERFERENCE, 5574 /* Represents the reason that non-802.11 generic Wideband (WB) 5575 * interference has been found in the current channel. 5576 */ 5577 QCA_WLAN_VENDOR_ACS_SELECT_REASON_NON_80211_WB_INTERFERENCE, 5578 /* Represents the reason that Jammer interference has been found in the 5579 * current channel. 5580 */ 5581 QCA_WLAN_VENDOR_ACS_SELECT_REASON_JAMMER_INTERFERENCE, 5582 }; 5583 5584 /** 5585 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for 5586 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd 5587 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the 5588 * external ACS policies to select the channels w.r.t. the PCL weights. 5589 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and 5590 * their PCL weights.) 5591 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to 5592 * select a channel with non-zero PCL weight. 5593 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a 5594 * channel with non-zero PCL weight. 5595 * 5596 */ 5597 enum qca_wlan_vendor_attr_external_acs_policy { 5598 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, 5599 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, 5600 }; 5601 5602 /** 5603 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. 5604 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. 5605 */ 5606 enum qca_wlan_vendor_channel_prop_flags { 5607 /* Bits 0, 1, 2, and 3 are reserved */ 5608 5609 /* Turbo channel */ 5610 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, 5611 /* CCK channel */ 5612 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, 5613 /* OFDM channel */ 5614 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, 5615 /* 2.4 GHz spectrum channel. */ 5616 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, 5617 /* 5 GHz spectrum channel */ 5618 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, 5619 /* Only passive scan allowed */ 5620 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, 5621 /* Dynamic CCK-OFDM channel */ 5622 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, 5623 /* GFSK channel (FHSS PHY) */ 5624 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, 5625 /* Radar found on channel */ 5626 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, 5627 /* 11a static turbo channel only */ 5628 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, 5629 /* Half rate channel */ 5630 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, 5631 /* Quarter rate channel */ 5632 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, 5633 /* HT 20 channel */ 5634 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, 5635 /* HT 40 with extension channel above */ 5636 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, 5637 /* HT 40 with extension channel below */ 5638 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, 5639 /* HT 40 intolerant */ 5640 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, 5641 /* VHT 20 channel */ 5642 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, 5643 /* VHT 40 with extension channel above */ 5644 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, 5645 /* VHT 40 with extension channel below */ 5646 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, 5647 /* VHT 80 channel */ 5648 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, 5649 /* HT 40 intolerant mark bit for ACS use */ 5650 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, 5651 /* Channel temporarily blocked due to noise */ 5652 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, 5653 /* VHT 160 channel */ 5654 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, 5655 /* VHT 80+80 channel */ 5656 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, 5657 /* HE 20 channel */ 5658 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, 5659 /* HE 40 with extension channel above */ 5660 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, 5661 /* HE 40 with extension channel below */ 5662 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, 5663 /* HE 40 intolerant */ 5664 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, 5665 }; 5666 5667 /** 5668 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a 5669 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is 5670 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. 5671 */ 5672 enum qca_wlan_vendor_channel_prop_flags_2 { 5673 /* HE 40 intolerant mark bit for ACS use */ 5674 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, 5675 /* HE 80 channel */ 5676 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, 5677 /* HE 160 channel */ 5678 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, 5679 /* HE 80+80 channel */ 5680 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, 5681 }; 5682 5683 /** 5684 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for 5685 * each channel. This is used by 5686 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. 5687 */ 5688 enum qca_wlan_vendor_channel_prop_flags_ext { 5689 /* Radar found on channel */ 5690 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, 5691 /* DFS required on channel */ 5692 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, 5693 /* DFS required on channel for 2nd band of 80+80 */ 5694 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, 5695 /* If channel has been checked for DFS */ 5696 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, 5697 /* Excluded in 802.11d */ 5698 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, 5699 /* Channel Switch Announcement received on this channel */ 5700 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, 5701 /* Ad-hoc is not allowed */ 5702 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, 5703 /* Station only channel */ 5704 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, 5705 /* DFS radar history for client device (STA mode) */ 5706 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, 5707 /* DFS CAC valid for client device (STA mode) */ 5708 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, 5709 }; 5710 5711 /** 5712 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel 5713 * information. These attributes are sent as part of 5714 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following 5715 * attributes correspond to a single channel. 5716 */ 5717 enum qca_wlan_vendor_external_acs_event_chan_info_attr { 5718 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, 5719 5720 /* A bitmask (u32) with flags specified in 5721 * enum qca_wlan_vendor_channel_prop_flags. 5722 */ 5723 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, 5724 /* A bitmask (u32) with flags specified in 5725 * enum qca_wlan_vendor_channel_prop_flags_ext. 5726 */ 5727 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, 5728 /* frequency in MHz (u32) */ 5729 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, 5730 /* maximum regulatory transmission power (u32) */ 5731 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, 5732 /* maximum transmission power (u32) */ 5733 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, 5734 /* minimum transmission power (u32) */ 5735 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, 5736 /* regulatory class id (u8) */ 5737 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, 5738 /* maximum antenna gain in (u8) */ 5739 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, 5740 /* VHT segment 0 (u8) */ 5741 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, 5742 /* VHT segment 1 (u8) */ 5743 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, 5744 /* A bitmask (u32) with flags specified in 5745 * enum qca_wlan_vendor_channel_prop_flags_2. 5746 */ 5747 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, 5748 5749 /* 5750 * VHT segment 0 in MHz (u32) and the attribute is mandatory. 5751 * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes 5752 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 5753 * along with 5754 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0. 5755 * 5756 * If both the driver and user-space application supports the 6 GHz 5757 * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 5758 * is deprecated and 5759 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 5760 * should be used. 5761 * 5762 * To maintain backward compatibility, 5763 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 5764 * is still used if either of the driver or user space application 5765 * doesn't support the 6 GHz band. 5766 */ 5767 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_0 = 12, 5768 5769 /* 5770 * VHT segment 1 in MHz (u32) and the attribute is mandatory. 5771 * Note: Event QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS includes 5772 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 5773 * along with 5774 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1. 5775 * 5776 * If both the driver and user-space application supports the 6 GHz 5777 * band, QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 5778 * is deprecated and 5779 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 5780 * should be considered. 5781 * 5782 * To maintain backward compatibility, 5783 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 5784 * is still used if either of the driver or user space application 5785 * doesn't support the 6 GHz band. 5786 */ 5787 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ_VHT_SEG_1 = 13, 5788 5789 /* keep last */ 5790 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, 5791 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = 5792 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, 5793 }; 5794 5795 /** 5796 * qca_wlan_vendor_attr_pcl: Represents attributes for 5797 * preferred channel list (PCL). These attributes are sent as part of 5798 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and 5799 * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST. 5800 */ 5801 enum qca_wlan_vendor_attr_pcl { 5802 QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, 5803 5804 /* Channel number (u8) */ 5805 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, 5806 /* Channel weightage (u8) */ 5807 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, 5808 /* Channel frequency (u32) in MHz */ 5809 QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3, 5810 /* Channel flags (u32) 5811 * bit 0 set: channel to be used for GO role, 5812 * bit 1 set: channel to be used on CLI role, 5813 * bit 2 set: channel must be considered for operating channel 5814 * selection & peer chosen operating channel should be 5815 * one of the channels with this flag set, 5816 * bit 3 set: channel should be excluded in GO negotiation 5817 */ 5818 QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4, 5819 }; 5820 5821 /** 5822 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command 5823 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by 5824 * host driver. 5825 */ 5826 enum qca_wlan_vendor_attr_external_acs_event { 5827 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, 5828 5829 /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason. 5830 * This helps ACS module to understand why ACS needs to be started. 5831 */ 5832 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, 5833 /* Flag attribute to indicate if driver supports spectral scanning */ 5834 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, 5835 /* Flag attribute to indicate if 11ac is offloaded to firmware */ 5836 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, 5837 /* Flag attribute to indicate if driver provides additional channel 5838 * capability as part of scan operation 5839 */ 5840 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, 5841 /* Flag attribute to indicate interface status is UP */ 5842 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, 5843 /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype 5844 * values. 5845 */ 5846 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, 5847 /* Channel width (u8). It takes one of enum nl80211_chan_width values. 5848 * This is the upper bound of channel width. ACS logic should try to get 5849 * a channel with the specified width and if not found, look for lower 5850 * values. 5851 */ 5852 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, 5853 /* This (u8) will hold values of one of enum nl80211_bands */ 5854 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, 5855 /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode 5856 * values 5857 */ 5858 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, 5859 /* Array of (u32) supported frequency list among which ACS should choose 5860 * best frequency. 5861 */ 5862 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, 5863 /* Preferred channel list by the driver which will have array of nested 5864 * values as per enum qca_wlan_vendor_attr_pcl attribute. 5865 */ 5866 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, 5867 /* Array of nested attribute for each channel. It takes attr as defined 5868 * in enum qca_wlan_vendor_external_acs_event_chan_info_attr. 5869 */ 5870 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, 5871 /* External ACS policy such as PCL mandatory, PCL preferred, etc. 5872 * It uses values defined in enum 5873 * qca_wlan_vendor_attr_external_acs_policy. 5874 */ 5875 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, 5876 /* Reference RF Operating Parameter (RROP) availability information 5877 * (u16). It uses values defined in enum 5878 * qca_wlan_vendor_attr_rropavail_info. 5879 */ 5880 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, 5881 5882 /* keep last */ 5883 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, 5884 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = 5885 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, 5886 }; 5887 5888 /** 5889 * enum qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd 5890 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels 5891 * in priority order as decided after ACS operation in userspace. 5892 * 5893 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON: Required (u8). 5894 * One of reason code from enum qca_wlan_vendor_acs_select_reason. 5895 * 5896 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST: Required 5897 * Array of nested values for each channel with following attributes: 5898 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, 5899 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, 5900 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, 5901 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, 5902 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 5903 * Note: If both the driver and user-space application supports the 6 GHz band, 5904 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST is deprecated and use 5905 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST. 5906 * To maintain backward compatibility, 5907 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST 5908 * is still used if either of the driver or user space application doesn't 5909 * support the 6 GHz band. 5910 * 5911 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY: Required (u8). 5912 * Primary channel number 5913 * Note: If both the driver and user-space application supports the 6 GHz band, 5914 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY is deprecated and use 5915 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY. 5916 * To maintain backward compatibility, 5917 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY 5918 * is still used if either of the driver or user space application doesn't 5919 * support the 6 GHz band. 5920 * 5921 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY: Required (u8). 5922 * Secondary channel number, required only for 160 and 80+80 MHz bandwidths. 5923 * Note: If both the driver and user-space application supports the 6 GHz band, 5924 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY is deprecated and use 5925 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY. 5926 * To maintain backward compatibility, 5927 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY 5928 * is still used if either of the driver or user space application 5929 * doesn't support the 6 GHz band. 5930 * 5931 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0: Required (u8). 5932 * VHT seg0 channel number 5933 * Note: If both the driver and user-space application supports the 6 GHz band, 5934 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 is deprecated and use 5935 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0. 5936 * To maintain backward compatibility, 5937 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 5938 * is still used if either of the driver or user space application 5939 * doesn't support the 6 GHz band. 5940 * 5941 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1: Required (u8). 5942 * VHT seg1 channel number 5943 * Note: If both the driver and user-space application supports the 6 GHz band, 5944 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 is deprecated and use 5945 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1. 5946 * To maintain backward compatibility, 5947 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 5948 * is still used if either of the driver or user space application 5949 * doesn't support the 6 GHz band. 5950 * 5951 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH: Required (u8). 5952 * Takes one of enum nl80211_chan_width values. 5953 * 5954 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST: Required 5955 * Array of nested values for each channel with following attributes: 5956 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY in MHz (u32), 5957 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY in MHz (u32), 5958 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 in MHz (u32), 5959 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 in MHz (u32), 5960 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 5961 * Note: If user-space application has no support of the 6 GHz band, this 5962 * attribute is optional. 5963 * 5964 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY: Required (u32) 5965 * Primary channel frequency in MHz 5966 * Note: If user-space application has no support of the 6 GHz band, this 5967 * attribute is optional. 5968 * 5969 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY: Required (u32) 5970 * Secondary channel frequency in MHz used for HT 40 MHz channels. 5971 * Note: If user-space application has no support of the 6 GHz band, this 5972 * attribute is optional. 5973 * 5974 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0: Required (u32) 5975 * VHT seg0 channel frequency in MHz 5976 * Note: If user-space application has no support of the 6GHz band, this 5977 * attribute is optional. 5978 * 5979 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1: Required (u32) 5980 * VHT seg1 channel frequency in MHz 5981 * Note: If user-space application has no support of the 6 GHz band, this 5982 * attribute is optional. 5983 */ 5984 enum qca_wlan_vendor_attr_external_acs_channels { 5985 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, 5986 5987 /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason 5988 */ 5989 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, 5990 5991 /* Array of nested values for each channel with following attributes: 5992 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, 5993 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, 5994 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, 5995 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, 5996 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, 5997 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 5998 */ 5999 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, 6000 /* This (u8) will hold values of one of enum nl80211_bands */ 6001 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, 6002 /* Primary channel (u8) */ 6003 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, 6004 /* Secondary channel (u8) used for HT 40 MHz channels */ 6005 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, 6006 /* VHT seg0 channel (u8) */ 6007 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, 6008 /* VHT seg1 channel (u8) */ 6009 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, 6010 /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ 6011 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, 6012 6013 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_LIST = 9, 6014 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_PRIMARY = 10, 6015 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_SECONDARY = 11, 6016 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG0 = 12, 6017 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_FREQUENCY_CENTER_SEG1 = 13, 6018 6019 /* keep last */ 6020 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, 6021 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = 6022 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 6023 }; 6024 6025 enum qca_chip_power_save_failure_reason { 6026 /* Indicates if the reason for the failure is due to a protocol 6027 * layer/module. 6028 */ 6029 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, 6030 /* Indicates if the reason for the failure is due to a hardware issue. 6031 */ 6032 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, 6033 }; 6034 6035 /** 6036 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd 6037 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite 6038 * information leading to the power save failure. 6039 */ 6040 enum qca_attr_chip_power_save_failure { 6041 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, 6042 /* Reason to cause the power save failure. 6043 * These reasons are represented by 6044 * enum qca_chip_power_save_failure_reason. 6045 */ 6046 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, 6047 6048 /* keep last */ 6049 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, 6050 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = 6051 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, 6052 }; 6053 6054 /** 6055 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various 6056 * data types for which the stats have to get collected. 6057 */ 6058 enum qca_wlan_vendor_nud_stats_data_pkt_flags { 6059 QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0, 6060 QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1, 6061 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2, 6062 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3, 6063 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4, 6064 /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get 6065 * to represent the stats of respective data type. 6066 */ 6067 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5, 6068 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6, 6069 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7, 6070 }; 6071 6072 enum qca_wlan_vendor_nud_stats_set_data_pkt_info { 6073 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0, 6074 /* Represents the data packet type to be monitored (u32). 6075 * Host driver tracks the stats corresponding to each data frame 6076 * represented by these flags. 6077 * These data packets are represented by 6078 * enum qca_wlan_vendor_nud_stats_data_pkt_flags 6079 */ 6080 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1, 6081 /* Name corresponding to the DNS frame for which the respective DNS 6082 * stats have to get monitored (string). Max string length 255. 6083 */ 6084 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2, 6085 /* source port on which the respective proto stats have to get 6086 * collected (u32). 6087 */ 6088 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3, 6089 /* destination port on which the respective proto stats have to get 6090 * collected (u32). 6091 */ 6092 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4, 6093 /* IPv4 address for which the destined data packets have to be 6094 * monitored. (in network byte order), u32. 6095 */ 6096 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5, 6097 /* IPv6 address for which the destined data packets have to be 6098 * monitored. (in network byte order), 16 bytes array. 6099 */ 6100 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6, 6101 6102 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST, 6103 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX = 6104 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1, 6105 }; 6106 6107 /** 6108 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd 6109 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite 6110 * information to start/stop the NUD statistics collection. 6111 */ 6112 enum qca_attr_nud_stats_set { 6113 QCA_ATTR_NUD_STATS_SET_INVALID = 0, 6114 6115 /* Flag to start/stop the NUD statistics collection. 6116 * Start - If included, Stop - If not included 6117 */ 6118 QCA_ATTR_NUD_STATS_SET_START = 1, 6119 /* IPv4 address of the default gateway (in network byte order), u32 */ 6120 QCA_ATTR_NUD_STATS_GW_IPV4 = 2, 6121 /* Represents the list of data packet types to be monitored. 6122 * Host driver tracks the stats corresponding to each data frame 6123 * represented by these flags. 6124 * These data packets are represented by 6125 * enum qca_wlan_vendor_nud_stats_set_data_pkt_info 6126 */ 6127 QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, 6128 6129 /* keep last */ 6130 QCA_ATTR_NUD_STATS_SET_LAST, 6131 QCA_ATTR_NUD_STATS_SET_MAX = 6132 QCA_ATTR_NUD_STATS_SET_LAST - 1, 6133 }; 6134 6135 enum qca_attr_nud_data_stats { 6136 QCA_ATTR_NUD_DATA_STATS_INVALID = 0, 6137 /* Data packet type for which the stats are collected (u32). 6138 * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags 6139 */ 6140 QCA_ATTR_NUD_STATS_PKT_TYPE = 1, 6141 /* Name corresponding to the DNS frame for which the respective DNS 6142 * stats are monitored (string). Max string length 255. 6143 */ 6144 QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2, 6145 /* source port on which the respective proto stats are collected (u32). 6146 */ 6147 QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3, 6148 /* destination port on which the respective proto stats are collected 6149 * (u32). 6150 */ 6151 QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4, 6152 /* IPv4 address for which the destined data packets have to be 6153 * monitored. (in network byte order), u32. 6154 */ 6155 QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5, 6156 /* IPv6 address for which the destined data packets have to be 6157 * monitored. (in network byte order), 16 bytes array. 6158 */ 6159 QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6, 6160 /* Data packet Request count received from netdev (u32). */ 6161 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, 6162 /* Data packet Request count sent to lower MAC from upper MAC (u32). */ 6163 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, 6164 /* Data packet Request count received by lower MAC from upper MAC 6165 * (u32) 6166 */ 6167 QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, 6168 /* Data packet Request count successfully transmitted by the device 6169 * (u32) 6170 */ 6171 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, 6172 /* Data packet Response count received by lower MAC (u32) */ 6173 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, 6174 /* Data packet Response count received by upper MAC (u32) */ 6175 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, 6176 /* Data packet Response count delivered to netdev (u32) */ 6177 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, 6178 /* Data Packet Response count that are dropped out of order (u32) */ 6179 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, 6180 6181 /* keep last */ 6182 QCA_ATTR_NUD_DATA_STATS_LAST, 6183 QCA_ATTR_NUD_DATA_STATS_MAX = 6184 QCA_ATTR_NUD_DATA_STATS_LAST - 1, 6185 }; 6186 6187 /** 6188 * qca_attr_nud_stats_get: Attributes to vendor subcmd 6189 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite 6190 * NUD statistics collected when queried. 6191 */ 6192 enum qca_attr_nud_stats_get { 6193 QCA_ATTR_NUD_STATS_GET_INVALID = 0, 6194 /* ARP Request count from netdev (u32) */ 6195 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, 6196 /* ARP Request count sent to lower MAC from upper MAC (u32) */ 6197 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, 6198 /* ARP Request count received by lower MAC from upper MAC (u32) */ 6199 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, 6200 /* ARP Request count successfully transmitted by the device (u32) */ 6201 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, 6202 /* ARP Response count received by lower MAC (u32) */ 6203 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, 6204 /* ARP Response count received by upper MAC (u32) */ 6205 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, 6206 /* ARP Response count delivered to netdev (u32) */ 6207 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, 6208 /* ARP Response count dropped due to out of order reception (u32) */ 6209 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, 6210 /* Flag indicating if the station's link to the AP is active. 6211 * Active Link - If included, Inactive link - If not included 6212 */ 6213 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, 6214 /* Flag indicating if there is any duplicate address detected (DAD). 6215 * Yes - If detected, No - If not detected. 6216 */ 6217 QCA_ATTR_NUD_STATS_IS_DAD = 10, 6218 /* List of Data packet types for which the stats are requested. 6219 * This list does not carry ARP stats as they are done by the 6220 * above attributes. Represented by enum qca_attr_nud_data_stats. 6221 */ 6222 QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, 6223 6224 /* keep last */ 6225 QCA_ATTR_NUD_STATS_GET_LAST, 6226 QCA_ATTR_NUD_STATS_GET_MAX = 6227 QCA_ATTR_NUD_STATS_GET_LAST - 1, 6228 }; 6229 6230 enum qca_wlan_btm_candidate_status { 6231 QCA_STATUS_ACCEPT = 0, 6232 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, 6233 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, 6234 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, 6235 QCA_STATUS_REJECT_LOW_RSSI = 4, 6236 QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, 6237 QCA_STATUS_REJECT_UNKNOWN = 6, 6238 }; 6239 6240 enum qca_wlan_vendor_attr_btm_candidate_info { 6241 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, 6242 6243 /* 6-byte MAC address representing the BSSID of transition candidate */ 6244 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, 6245 /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status 6246 * returned by the driver. It says whether the BSSID provided in 6247 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by 6248 * the driver, if not it specifies the reason for rejection. 6249 * Note that the user-space can overwrite the transition reject reason 6250 * codes provided by driver based on more information. 6251 */ 6252 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, 6253 6254 /* keep last */ 6255 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, 6256 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = 6257 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, 6258 }; 6259 6260 enum qca_attr_trace_level { 6261 QCA_ATTR_TRACE_LEVEL_INVALID = 0, 6262 /* 6263 * Nested array of the following attributes: 6264 * QCA_ATTR_TRACE_LEVEL_MODULE, 6265 * QCA_ATTR_TRACE_LEVEL_MASK. 6266 */ 6267 QCA_ATTR_TRACE_LEVEL_PARAM = 1, 6268 /* 6269 * Specific QCA host driver module. Please refer to the QCA host 6270 * driver implementation to get the specific module ID. 6271 */ 6272 QCA_ATTR_TRACE_LEVEL_MODULE = 2, 6273 /* Different trace level masks represented in the QCA host driver. */ 6274 QCA_ATTR_TRACE_LEVEL_MASK = 3, 6275 6276 /* keep last */ 6277 QCA_ATTR_TRACE_LEVEL_AFTER_LAST, 6278 QCA_ATTR_TRACE_LEVEL_MAX = 6279 QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, 6280 }; 6281 6282 /** 6283 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities 6284 */ 6285 enum qca_wlan_vendor_attr_get_he_capabilities { 6286 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0, 6287 /* Whether HE capabilities is supported 6288 * (u8 attribute: 0 = not supported, 1 = supported) 6289 */ 6290 QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1, 6291 /* HE PHY capabilities, array of 3 u32 values */ 6292 QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2, 6293 /* HE MAC capabilities (u32 attribute) */ 6294 QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3, 6295 /* HE MCS map (u32 attribute) */ 6296 QCA_WLAN_VENDOR_ATTR_HE_MCS = 4, 6297 /* Number of SS (u32 attribute) */ 6298 QCA_WLAN_VENDOR_ATTR_NUM_SS = 5, 6299 /* RU count (u32 attribute) */ 6300 QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6, 6301 /* PPE threshold data, array of 8 u32 values */ 6302 QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7, 6303 6304 /* keep last */ 6305 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST, 6306 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX = 6307 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1, 6308 }; 6309 6310 /** 6311 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters 6312 */ 6313 enum qca_wlan_vendor_attr_spectral_scan { 6314 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, 6315 /* Number of times the chip enters spectral scan mode before 6316 * deactivating spectral scans. When set to 0, chip will enter spectral 6317 * scan mode continuously. u32 attribute. 6318 */ 6319 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, 6320 /* Spectral scan period. Period increment resolution is 256*Tclk, 6321 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. 6322 */ 6323 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, 6324 /* Spectral scan priority. u32 attribute. */ 6325 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, 6326 /* Number of FFT data points to compute. u32 attribute. */ 6327 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, 6328 /* Enable targeted gain change before starting the spectral scan FFT. 6329 * u32 attribute. 6330 */ 6331 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, 6332 /* Restart a queued spectral scan. u32 attribute. */ 6333 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, 6334 /* Noise floor reference number for the calculation of bin power. 6335 * u32 attribute. 6336 */ 6337 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, 6338 /* Disallow spectral scan triggers after TX/RX packets by setting 6339 * this delay value to roughly SIFS time period or greater. 6340 * u32 attribute. 6341 */ 6342 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, 6343 /* Number of strong bins (inclusive) per sub-channel, below 6344 * which a signal is declared a narrow band tone. u32 attribute. 6345 */ 6346 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, 6347 /* Specify the threshold over which a bin is declared strong (for 6348 * scan bandwidth analysis). u32 attribute. 6349 */ 6350 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, 6351 /* Spectral scan report mode. u32 attribute. */ 6352 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, 6353 /* RSSI report mode, if the ADC RSSI is below 6354 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, 6355 * then FFTs will not trigger, but timestamps and summaries get 6356 * reported. u32 attribute. 6357 */ 6358 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, 6359 /* ADC RSSI must be greater than or equal to this threshold (signed dB) 6360 * to ensure spectral scan reporting with normal error code. 6361 * u32 attribute. 6362 */ 6363 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, 6364 /* Format of frequency bin magnitude for spectral scan triggered FFTs: 6365 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). 6366 * u32 attribute. 6367 */ 6368 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, 6369 /* Format of FFT report to software for spectral scan triggered FFTs. 6370 * 0: No FFT report (only spectral scan summary report) 6371 * 1: 2-dword summary of metrics for each completed FFT + spectral scan 6372 * report 6373 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled 6374 * bins (in-band) per FFT + spectral scan summary report 6375 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled 6376 * bins (all) per FFT + spectral scan summary report 6377 * u32 attribute. 6378 */ 6379 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, 6380 /* Number of LSBs to shift out in order to scale the FFT bins. 6381 * u32 attribute. 6382 */ 6383 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, 6384 /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes 6385 * in dBm power. u32 attribute. 6386 */ 6387 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, 6388 /* Per chain enable mask to select input ADC for search FFT. 6389 * u32 attribute. 6390 */ 6391 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, 6392 /* An unsigned 64-bit integer provided by host driver to identify the 6393 * spectral scan request. This attribute is included in the scan 6394 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START 6395 * and used as an attribute in 6396 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the 6397 * specific scan to be stopped. 6398 */ 6399 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, 6400 /* Skip interval for FFT reports. u32 attribute */ 6401 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, 6402 /* Set to report only one set of FFT results. 6403 * u32 attribute. 6404 */ 6405 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, 6406 /* Debug level for spectral module in driver. 6407 * 0 : Verbosity level 0 6408 * 1 : Verbosity level 1 6409 * 2 : Verbosity level 2 6410 * 3 : Matched filterID display 6411 * 4 : One time dump of FFT report 6412 * u32 attribute. 6413 */ 6414 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, 6415 /* Type of spectral scan request. u32 attribute. 6416 * It uses values defined in enum 6417 * qca_wlan_vendor_attr_spectral_scan_request_type. 6418 */ 6419 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, 6420 /* This specifies the frequency span over which spectral 6421 * scan would be carried out. Its value depends on the 6422 * value of QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and 6423 * the relation is as follows. 6424 * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL 6425 * Not applicable. Spectral scan would happen in the 6426 * operating span. 6427 * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE 6428 * Center frequency (in MHz) of the span of interest or 6429 * for convenience, center frequency (in MHz) of any channel 6430 * in the span of interest. For 80+80 MHz agile spectral scan 6431 * request it represents center frequency (in MHz) of the primary 6432 * 80 MHz span or for convenience, center frequency (in MHz) of any 6433 * channel in the primary 80 MHz span. If agile spectral scan is 6434 * initiated without setting a valid frequency it returns the 6435 * error code 6436 * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED). 6437 * u32 attribute. 6438 */ 6439 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY = 24, 6440 /* Spectral scan mode. u32 attribute. 6441 * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. 6442 * If this attribute is not present, it is assumed to be 6443 * normal mode (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL). 6444 */ 6445 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE = 25, 6446 /* Spectral scan error code. u32 attribute. 6447 * It uses values defined in enum 6448 * qca_wlan_vendor_spectral_scan_error_code. 6449 * This attribute is included only in failure scenarios. 6450 */ 6451 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE = 26, 6452 /* 8-bit unsigned value to enable/disable debug of the 6453 * Spectral DMA ring. 6454 * 1-enable, 0-disable 6455 */ 6456 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_RING_DEBUG = 27, 6457 /* 8-bit unsigned value to enable/disable debug of the 6458 * Spectral DMA buffers. 6459 * 1-enable, 0-disable 6460 */ 6461 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DMA_BUFFER_DEBUG = 28, 6462 /* This specifies the frequency span over which spectral scan would be 6463 * carried out. Its value depends on the value of 6464 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE and the relation is as 6465 * follows. 6466 * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL 6467 * Not applicable. Spectral scan would happen in the operating span. 6468 * QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE 6469 * This attribute is applicable only for agile spectral scan 6470 * requests in 80+80 MHz mode. It represents center frequency (in 6471 * MHz) of the secondary 80 MHz span or for convenience, center 6472 * frequency (in MHz) of any channel in the secondary 80 MHz span. 6473 * u32 attribute. 6474 */ 6475 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FREQUENCY_2 = 29, 6476 /* This attribute specifies the bandwidth to be used for spectral scan 6477 * operation. This is an u8 attribute and uses the values in enum 6478 * nl80211_chan_width. This is an optional attribute. 6479 * If this attribute is not populated, the driver should configure the 6480 * spectral scan bandwidth to the maximum value supported by the target 6481 * for the current operating bandwidth. 6482 */ 6483 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BANDWIDTH = 30, 6484 6485 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, 6486 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = 6487 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, 6488 }; 6489 6490 /** 6491 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command 6492 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. 6493 */ 6494 enum qca_wlan_vendor_attr_spectral_diag_stats { 6495 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, 6496 /* Number of spectral TLV signature mismatches. 6497 * u64 attribute. 6498 */ 6499 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, 6500 /* Number of spectral phyerror events with insufficient length when 6501 * parsing for secondary 80 search FFT report. u64 attribute. 6502 */ 6503 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, 6504 /* Number of spectral phyerror events without secondary 80 6505 * search FFT report. u64 attribute. 6506 */ 6507 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, 6508 /* Number of spectral phyerror events with vht operation segment 1 id 6509 * mismatches in search fft report. u64 attribute. 6510 */ 6511 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, 6512 /* Number of spectral phyerror events with vht operation segment 2 id 6513 * mismatches in search fft report. u64 attribute. 6514 */ 6515 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, 6516 6517 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, 6518 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = 6519 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, 6520 }; 6521 6522 /** 6523 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command 6524 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. 6525 */ 6526 enum qca_wlan_vendor_attr_spectral_cap { 6527 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, 6528 /* Flag attribute to indicate phydiag capability */ 6529 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, 6530 /* Flag attribute to indicate radar detection capability */ 6531 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, 6532 /* Flag attribute to indicate spectral capability */ 6533 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, 6534 /* Flag attribute to indicate advanced spectral capability */ 6535 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, 6536 /* Spectral hardware generation. u32 attribute. 6537 * It uses values defined in enum 6538 * qca_wlan_vendor_spectral_scan_cap_hw_gen. 6539 */ 6540 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, 6541 /* Spectral bin scaling formula ID. u16 attribute. 6542 * It uses values defined in enum 6543 * qca_wlan_vendor_spectral_scan_cap_formula_id. 6544 */ 6545 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, 6546 /* Spectral bin scaling param - low level offset. 6547 * s16 attribute. 6548 */ 6549 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, 6550 /* Spectral bin scaling param - high level offset. 6551 * s16 attribute. 6552 */ 6553 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, 6554 /* Spectral bin scaling param - RSSI threshold. 6555 * s16 attribute. 6556 */ 6557 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, 6558 /* Spectral bin scaling param - default AGC max gain. 6559 * u8 attribute. 6560 */ 6561 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, 6562 /* Flag attribute to indicate agile spectral scan capability 6563 * for 20/40/80 MHz modes. 6564 */ 6565 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL = 11, 6566 /* Flag attribute to indicate agile spectral scan capability 6567 * for 160 MHz mode. 6568 */ 6569 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_160 = 12, 6570 /* Flag attribute to indicate agile spectral scan capability 6571 * for 80+80 MHz mode. 6572 */ 6573 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_80_80 = 13, 6574 /* Number of spectral detectors used for scan in 20 MHz. 6575 * u32 attribute. 6576 */ 6577 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_20_MHZ = 14, 6578 /* Number of spectral detectors used for scan in 40 MHz. 6579 * u32 attribute. 6580 */ 6581 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_40_MHZ = 15, 6582 /* Number of spectral detectors used for scan in 80 MHz. 6583 * u32 attribute. 6584 */ 6585 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80_MHZ = 16, 6586 /* Number of spectral detectors used for scan in 160 MHz. 6587 * u32 attribute. 6588 */ 6589 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_160_MHZ = 17, 6590 /* Number of spectral detectors used for scan in 80+80 MHz. 6591 * u32 attribute. 6592 */ 6593 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_80P80_MHZ = 18, 6594 /* Flag attribute to indicate agile spectral scan capability 6595 * for 320 MHz mode. 6596 */ 6597 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AGILE_SPECTRAL_320 = 19, 6598 /* Number of spectral detectors used for scan in 320 MHz. 6599 * u32 attribute. 6600 */ 6601 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_NUM_DETECTORS_320_MHZ = 20, 6602 6603 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, 6604 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = 6605 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, 6606 }; 6607 6608 /** 6609 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command 6610 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. 6611 */ 6612 enum qca_wlan_vendor_attr_spectral_scan_status { 6613 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, 6614 /* Flag attribute to indicate whether spectral scan is enabled */ 6615 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, 6616 /* Flag attribute to indicate whether spectral scan is in progress*/ 6617 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, 6618 /* Spectral scan mode. u32 attribute. 6619 * It uses values defined in enum qca_wlan_vendor_spectral_scan_mode. 6620 * If this attribute is not present, normal mode 6621 * (QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL is assumed to be 6622 * requested. 6623 */ 6624 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE = 3, 6625 6626 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, 6627 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = 6628 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, 6629 }; 6630 6631 /** 6632 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for 6633 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd 6634 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the 6635 * spectral scan request types. 6636 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to 6637 * set the spectral parameters and start scan. 6638 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to 6639 * only set the spectral parameters. 6640 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to 6641 * only start the spectral scan. 6642 */ 6643 enum qca_wlan_vendor_attr_spectral_scan_request_type { 6644 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, 6645 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, 6646 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, 6647 }; 6648 6649 /** 6650 * qca_wlan_vendor_spectral_scan_mode: Attribute values for 6651 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_MODE in the vendor subcmd 6652 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START and 6653 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MODE in the vendor subcmd 6654 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. This represents the 6655 * spectral scan modes. 6656 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL: Normal spectral scan: 6657 * spectral scan in the current operating span. 6658 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE: Agile spectral scan: 6659 * spectral scan in the configured agile span. 6660 */ 6661 enum qca_wlan_vendor_spectral_scan_mode { 6662 QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_NORMAL = 0, 6663 QCA_WLAN_VENDOR_SPECTRAL_SCAN_MODE_AGILE = 1, 6664 }; 6665 6666 /** 6667 * qca_wlan_vendor_spectral_scan_error_code: Attribute values for 6668 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_ERROR_CODE in the vendor subcmd 6669 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. 6670 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED: Changing the value 6671 * of a parameter is not supported. 6672 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED: Requested spectral scan 6673 * mode is not supported. 6674 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE: A parameter 6675 * has invalid value. 6676 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED: A parameter 6677 * is not initialized. 6678 */ 6679 enum qca_wlan_vendor_spectral_scan_error_code { 6680 QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_UNSUPPORTED = 0, 6681 QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_MODE_UNSUPPORTED = 1, 6682 QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_INVALID_VALUE = 2, 6683 QCA_WLAN_VENDOR_SPECTRAL_SCAN_ERR_PARAM_NOT_INITIALIZED = 3, 6684 }; 6685 6686 /** 6687 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for 6688 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd 6689 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 6690 * spectral hardware generation. 6691 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 6692 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 6693 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 6694 */ 6695 enum qca_wlan_vendor_spectral_scan_cap_hw_gen { 6696 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, 6697 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, 6698 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, 6699 }; 6700 6701 enum qca_wlan_vendor_tos { 6702 QCA_WLAN_VENDOR_TOS_BK = 0, 6703 QCA_WLAN_VENDOR_TOS_BE = 1, 6704 QCA_WLAN_VENDOR_TOS_VI = 2, 6705 QCA_WLAN_VENDOR_TOS_VO = 3, 6706 }; 6707 6708 /** 6709 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command 6710 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. 6711 */ 6712 enum qca_wlan_vendor_attr_active_tos { 6713 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, 6714 /* Type Of Service - Represented by qca_wlan_vendor_tos */ 6715 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, 6716 /* Flag attribute representing the start (attribute included) or stop 6717 * (attribute not included) of the respective TOS. 6718 */ 6719 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, 6720 }; 6721 6722 enum qca_wlan_vendor_hang_reason { 6723 /* Unspecified reason */ 6724 QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, 6725 /* No Map for the MAC entry for the received frame */ 6726 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, 6727 /* Peer deletion timeout happened */ 6728 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, 6729 /* Peer unmap timeout */ 6730 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, 6731 /* Scan request timed out */ 6732 QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, 6733 /* Consecutive Scan attempt failures */ 6734 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, 6735 /* Unable to get the message buffer */ 6736 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, 6737 /* Current command processing is timedout */ 6738 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, 6739 /* Timeout for an ACK from FW for suspend request */ 6740 QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, 6741 /* Timeout for an ACK from FW for resume request */ 6742 QCA_WLAN_HANG_RESUME_TIMEOUT = 9, 6743 /* Transmission timeout for consecutive data frames */ 6744 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, 6745 /* Timeout for the TX completion status of data frame */ 6746 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, 6747 /* DXE failure for TX/RX, DXE resource unavailability */ 6748 QCA_WLAN_HANG_DXE_FAILURE = 12, 6749 /* WMI pending commands exceed the maximum count */ 6750 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, 6751 /* Timeout for peer STA connection accept command's response from the 6752 * FW in AP mode. This command is triggered when a STA (peer) connects 6753 * to AP (DUT). 6754 */ 6755 QCA_WLAN_HANG_AP_STA_CONNECT_REQ_TIMEOUT = 14, 6756 /* Timeout for the AP connection accept command's response from the FW 6757 * in STA mode. This command is triggered when the STA (DUT) connects 6758 * to an AP (peer). 6759 */ 6760 QCA_WLAN_HANG_STA_AP_CONNECT_REQ_TIMEOUT = 15, 6761 /* Timeout waiting for the response to the MAC HW mode change command 6762 * sent to FW as a part of MAC mode switch among DBS (Dual Band 6763 * Simultaneous), SCC (Single Channel Concurrency), and MCC (Multi 6764 * Channel Concurrency) mode. 6765 */ 6766 QCA_WLAN_HANG_MAC_HW_MODE_CHANGE_TIMEOUT = 16, 6767 /* Timeout waiting for the response from FW to configure the MAC HW's 6768 * mode. This operation is to configure the single/two MACs in either 6769 * SCC/MCC/DBS mode. 6770 */ 6771 QCA_WLAN_HANG_MAC_HW_MODE_CONFIG_TIMEOUT = 17, 6772 /* Timeout waiting for response of VDEV start command from the FW */ 6773 QCA_WLAN_HANG_VDEV_START_RESPONSE_TIMED_OUT = 18, 6774 /* Timeout waiting for response of VDEV restart command from the FW */ 6775 QCA_WLAN_HANG_VDEV_RESTART_RESPONSE_TIMED_OUT = 19, 6776 /* Timeout waiting for response of VDEV stop command from the FW */ 6777 QCA_WLAN_HANG_VDEV_STOP_RESPONSE_TIMED_OUT = 20, 6778 /* Timeout waiting for response of VDEV delete command from the FW */ 6779 QCA_WLAN_HANG_VDEV_DELETE_RESPONSE_TIMED_OUT = 21, 6780 /* Timeout waiting for response of peer all delete request command to 6781 * the FW on a specific VDEV. 6782 */ 6783 QCA_WLAN_HANG_VDEV_PEER_DELETE_ALL_RESPONSE_TIMED_OUT = 22, 6784 /* WMI sequence mismatch between WMI command and Tx completion */ 6785 QCA_WLAN_HANG_WMI_BUF_SEQUENCE_MISMATCH = 23, 6786 /* Write to Device HAL register failed */ 6787 QCA_WLAN_HANG_REG_WRITE_FAILURE = 24, 6788 /* No credit left to send the wow_wakeup_from_sleep to firmware */ 6789 QCA_WLAN_HANG_SUSPEND_NO_CREDIT = 25, 6790 /* Bus failure */ 6791 QCA_WLAN_HANG_BUS_FAILURE = 26, 6792 /* tasklet/credit latency found */ 6793 QCA_WLAN_HANG_TASKLET_CREDIT_LATENCY_DETECT = 27, 6794 }; 6795 6796 /** 6797 * enum qca_wlan_vendor_attr_hang - Used by the vendor command 6798 * QCA_NL80211_VENDOR_SUBCMD_HANG. 6799 */ 6800 enum qca_wlan_vendor_attr_hang { 6801 QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, 6802 /* Reason for the hang - u32 attribute with a value from enum 6803 * qca_wlan_vendor_hang_reason. 6804 */ 6805 QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, 6806 /* The binary blob data associated with the hang reason specified by 6807 * QCA_WLAN_VENDOR_ATTR_HANG_REASON. This binary data is expected to 6808 * contain the required dump to analyze the reason for the hang. 6809 * NLA_BINARY attribute, the max size is 1024 bytes. 6810 */ 6811 QCA_WLAN_VENDOR_ATTR_HANG_REASON_DATA = 2, 6812 6813 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, 6814 QCA_WLAN_VENDOR_ATTR_HANG_MAX = 6815 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, 6816 }; 6817 6818 /** 6819 * enum qca_wlan_vendor_attr_flush_pending - Attributes for 6820 * flushing pending traffic in firmware. 6821 * 6822 * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address. 6823 * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending 6824 * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK, 6825 * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to 6826 * flush packets with access category. 6827 */ 6828 enum qca_wlan_vendor_attr_flush_pending { 6829 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0, 6830 QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1, 6831 QCA_WLAN_VENDOR_ATTR_AC = 2, 6832 6833 /* keep last */ 6834 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST, 6835 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX = 6836 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1, 6837 }; 6838 6839 /** 6840 * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for 6841 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd 6842 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 6843 * Spectral bin scaling formula ID. 6844 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling 6845 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain 6846 * and RSSI threshold based formula. 6847 */ 6848 enum qca_wlan_vendor_spectral_scan_cap_formula_id { 6849 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, 6850 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, 6851 }; 6852 6853 /** 6854 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative 6855 * RF Operating Parameter (RROP) information is available, and if so, at which 6856 * point in the application-driver interaction sequence it can be retrieved by 6857 * the application from the driver. This point may vary by architecture and 6858 * other factors. This is a u16 value. 6859 */ 6860 enum qca_wlan_vendor_attr_rropavail_info { 6861 /* RROP information is unavailable. */ 6862 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, 6863 /* RROP information is available and the application can retrieve the 6864 * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS 6865 * event from the driver. 6866 */ 6867 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, 6868 /* RROP information is available only after a vendor specific scan 6869 * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has 6870 * successfully completed. The application can retrieve the information 6871 * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from 6872 * the driver. 6873 */ 6874 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, 6875 }; 6876 6877 /** 6878 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific 6879 * Representative RF Operating Parameter (RROP) information. It is sent for the 6880 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is 6881 * intended for use by external Auto Channel Selection applications. It provides 6882 * guidance values for some RF parameters that are used by the system during 6883 * operation. These values could vary by channel, band, radio, and so on. 6884 */ 6885 enum qca_wlan_vendor_attr_rrop_info { 6886 QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, 6887 6888 /* Representative Tx Power List (RTPL) which has an array of nested 6889 * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. 6890 */ 6891 QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, 6892 6893 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, 6894 QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = 6895 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 6896 }; 6897 6898 /** 6899 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list 6900 * entry instances in the Representative Tx Power List (RTPL). It provides 6901 * simplified power values intended for helping external Auto channel Selection 6902 * applications compare potential Tx power performance between channels, other 6903 * operating conditions remaining identical. These values are not necessarily 6904 * the actual Tx power values that will be used by the system. They are also not 6905 * necessarily the max or average values that will be used. Instead, they are 6906 * relative, summarized keys for algorithmic use computed by the driver or 6907 * underlying firmware considering a number of vendor specific factors. 6908 */ 6909 enum qca_wlan_vendor_attr_rtplinst { 6910 QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, 6911 6912 /* Primary channel number (u8). 6913 * Note: If both the driver and user space application support the 6914 * 6 GHz band, this attribute is deprecated and 6915 * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY should be used. To 6916 * maintain backward compatibility, 6917 * QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY is still used if either the 6918 * driver or user space application or both do not support the 6 GHz 6919 * band. 6920 */ 6921 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, 6922 /* Representative Tx power in dBm (s32) with emphasis on throughput. */ 6923 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, 6924 /* Representative Tx power in dBm (s32) with emphasis on range. */ 6925 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, 6926 /* Primary channel center frequency (u32) in MHz */ 6927 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY_FREQUENCY = 4, 6928 6929 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, 6930 QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = 6931 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, 6932 }; 6933 6934 /** 6935 * enum qca_wlan_vendor_attr_config_latency_level - Level for 6936 * wlan latency module. 6937 * 6938 * There will be various of Wi-Fi functionality like scan/roaming/adaptive 6939 * power saving which would causing data exchange out of service, this 6940 * would be a big impact on latency. For latency sensitive applications over 6941 * Wi-Fi are intolerant to such operations and thus would configure them 6942 * to meet their respective needs. It is well understood by such applications 6943 * that altering the default behavior would degrade the Wi-Fi functionality 6944 * w.r.t the above pointed WLAN operations. 6945 * 6946 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: 6947 * Default WLAN operation level which throughput orientated. 6948 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE: 6949 * Use moderate level to improve latency by limit scan duration. 6950 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: 6951 * Use low latency level to benifit application like concurrent 6952 * downloading or video streaming via constraint scan/adaptive PS. 6953 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: 6954 * Use ultra low latency level to benefit for gaming/voice 6955 * application via constraint scan/roaming/adaptive PS. 6956 */ 6957 enum qca_wlan_vendor_attr_config_latency_level { 6958 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, 6959 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, 6960 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2, 6961 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, 6962 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, 6963 6964 /* keep last */ 6965 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, 6966 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = 6967 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, 6968 }; 6969 6970 /** 6971 * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command 6972 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 6973 */ 6974 enum qca_wlan_vendor_attr_mac { 6975 QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, 6976 6977 /* MAC mode info list which has an array of nested values as 6978 * per attributes in enum qca_wlan_vendor_attr_mac_mode_info. 6979 */ 6980 QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, 6981 6982 /* keep last */ 6983 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, 6984 QCA_WLAN_VENDOR_ATTR_MAC_MAX = 6985 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, 6986 }; 6987 6988 /** 6989 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected 6990 * Wi-Fi netdev interface on a respective MAC. 6991 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. 6992 */ 6993 enum qca_wlan_vendor_attr_mac_iface_info { 6994 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, 6995 /* Wi-Fi netdev's interface index (u32) */ 6996 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, 6997 /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */ 6998 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, 6999 7000 /* keep last */ 7001 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, 7002 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = 7003 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, 7004 }; 7005 7006 /** 7007 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. 7008 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the 7009 * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 7010 */ 7011 enum qca_wlan_vendor_attr_mac_info { 7012 QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, 7013 /* Hardware MAC ID associated for the MAC (u32) */ 7014 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, 7015 /* Band supported by the MAC at a given point. 7016 * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum 7017 * nl80211_band. 7018 */ 7019 QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, 7020 /* Refers to list of WLAN netdev interfaces associated with this MAC. 7021 * Represented by enum qca_wlan_vendor_attr_mac_iface_info. 7022 */ 7023 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, 7024 7025 /* keep last */ 7026 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, 7027 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = 7028 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, 7029 }; 7030 7031 /** 7032 * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command 7033 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET. 7034 */ 7035 enum qca_wlan_vendor_attr_get_logger_features { 7036 QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, 7037 /* Unsigned 32-bit enum value of wifi_logger_supported_features */ 7038 QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, 7039 /* keep last */ 7040 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, 7041 QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = 7042 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, 7043 }; 7044 7045 /** 7046 * enum wifi_logger_supported_features - Values for supported logger features 7047 */ 7048 enum wifi_logger_supported_features { 7049 WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)), 7050 WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)), 7051 WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)), 7052 WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)), 7053 WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)), 7054 WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)), 7055 WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)), 7056 WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)), 7057 WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)), 7058 }; 7059 7060 /** 7061 * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get 7062 * capabilities features 7063 */ 7064 enum qca_wlan_tdls_caps_features_supported { 7065 WIFI_TDLS_SUPPORT = (1 << (0)), 7066 WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)), 7067 WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2)) 7068 }; 7069 7070 /** 7071 * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command 7072 * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES. 7073 */ 7074 enum qca_wlan_vendor_attr_tdls_get_capabilities { 7075 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, 7076 /* Indicates the max concurrent sessions */ 7077 /* Unsigned 32-bit value */ 7078 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS, 7079 /* Indicates the support for features */ 7080 /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported 7081 */ 7082 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED, 7083 7084 /* keep last */ 7085 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, 7086 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = 7087 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, 7088 }; 7089 7090 /** 7091 * enum qca_wlan_offloaded_packets_sending_control - Offload packets control 7092 * command used as value for the attribute 7093 * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL. 7094 */ 7095 enum qca_wlan_offloaded_packets_sending_control { 7096 QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0, 7097 QCA_WLAN_OFFLOADED_PACKETS_SENDING_START, 7098 QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP 7099 }; 7100 7101 /** 7102 * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command 7103 * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS. 7104 */ 7105 enum qca_wlan_vendor_attr_offloaded_packets { 7106 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, 7107 /* Takes valid value from the enum 7108 * qca_wlan_offloaded_packets_sending_control 7109 * Unsigned 32-bit value 7110 */ 7111 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, 7112 /* Unsigned 32-bit value */ 7113 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, 7114 /* array of u8 len: Max packet size */ 7115 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, 7116 /* 6-byte MAC address used to represent source MAC address */ 7117 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, 7118 /* 6-byte MAC address used to represent destination MAC address */ 7119 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, 7120 /* Unsigned 32-bit value, in milli seconds */ 7121 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, 7122 /* This optional unsigned 16-bit attribute is used for specifying 7123 * ethernet protocol type. If not specified ethertype defaults to IPv4. 7124 */ 7125 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_ETHER_PROTO_TYPE, 7126 7127 /* keep last */ 7128 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, 7129 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = 7130 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, 7131 }; 7132 7133 /** 7134 * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values 7135 * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL. 7136 */ 7137 enum qca_wlan_rssi_monitoring_control { 7138 QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, 7139 QCA_WLAN_RSSI_MONITORING_START, 7140 QCA_WLAN_RSSI_MONITORING_STOP, 7141 }; 7142 7143 /** 7144 * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command 7145 * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI. 7146 */ 7147 enum qca_wlan_vendor_attr_rssi_monitoring { 7148 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, 7149 /* Takes valid value from the enum 7150 * qca_wlan_rssi_monitoring_control 7151 * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control 7152 */ 7153 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, 7154 /* Unsigned 32-bit value */ 7155 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, 7156 /* Signed 8-bit value in dBm */ 7157 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, 7158 /* Signed 8-bit value in dBm */ 7159 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, 7160 /* attributes to be used/received in callback */ 7161 /* 6-byte MAC address used to represent current BSSID MAC address */ 7162 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, 7163 /* Signed 8-bit value indicating the current RSSI */ 7164 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, 7165 /* keep last */ 7166 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, 7167 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = 7168 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, 7169 }; 7170 7171 /** 7172 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command 7173 * QCA_NL80211_VENDOR_SUBCMD_NDP. 7174 */ 7175 enum qca_wlan_vendor_attr_ndp_params { 7176 QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, 7177 /* Unsigned 32-bit value 7178 * enum of sub commands values in qca_wlan_ndp_sub_cmd 7179 */ 7180 QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD, 7181 /* Unsigned 16-bit value */ 7182 QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID, 7183 /* NL attributes for data used NDP SUB cmds */ 7184 /* Unsigned 32-bit value indicating a service info */ 7185 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID, 7186 /* Unsigned 32-bit value; channel frequency in MHz */ 7187 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL, 7188 /* Interface Discovery MAC address. An array of 6 Unsigned int8 */ 7189 QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR, 7190 /* Interface name on which NDP is being created */ 7191 QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR, 7192 /* Unsigned 32-bit value for security */ 7193 /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */ 7194 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY, 7195 /* Unsigned 32-bit value for QoS */ 7196 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS, 7197 /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */ 7198 QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO, 7199 /* Unsigned 32-bit value for NDP instance Id */ 7200 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID, 7201 /* Array of instance Ids */ 7202 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY, 7203 /* Unsigned 32-bit value for initiator/responder NDP response code 7204 * accept/reject 7205 */ 7206 QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE, 7207 /* NDI MAC address. An array of 6 Unsigned int8 */ 7208 QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR, 7209 /* Unsigned 32-bit value errors types returned by driver 7210 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy 7211 * NanStatusType includes these values. 7212 */ 7213 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE, 7214 /* Unsigned 32-bit value error values returned by driver 7215 * The nan_i.h in AOSP project platform/hardware/qcom/wlan 7216 * NanInternalStatusType includes these values. 7217 */ 7218 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE, 7219 /* Unsigned 32-bit value for Channel setup configuration 7220 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy 7221 * NanDataPathChannelCfg includes these values. 7222 */ 7223 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG, 7224 /* Unsigned 32-bit value for Cipher Suite Shared Key Type */ 7225 QCA_WLAN_VENDOR_ATTR_NDP_CSID, 7226 /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */ 7227 QCA_WLAN_VENDOR_ATTR_NDP_PMK, 7228 /* Security Context Identifier that contains the PMKID 7229 * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes 7230 */ 7231 QCA_WLAN_VENDOR_ATTR_NDP_SCID, 7232 /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */ 7233 QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE, 7234 /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */ 7235 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME, 7236 /* Unsigned 32-bit bitmap indicating schedule update 7237 * BIT_0: NSS Update 7238 * BIT_1: Channel list update 7239 */ 7240 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON, 7241 /* Unsigned 32-bit value for NSS */ 7242 QCA_WLAN_VENDOR_ATTR_NDP_NSS, 7243 /* Unsigned 32-bit value for NUMBER NDP CHANNEL */ 7244 QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS, 7245 /* Unsigned 32-bit value for CHANNEL BANDWIDTH 7246 * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz 7247 */ 7248 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH, 7249 /* Array of channel/band width */ 7250 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO, 7251 /* IPv6 address used by NDP (in network byte order), 16 bytes array. 7252 * This attribute is used and optional for ndp request, ndp response, 7253 * ndp indication, and ndp confirm. 7254 */ 7255 QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, 7256 /* Unsigned 16-bit value indicating transport port used by NDP. 7257 * This attribute is used and optional for ndp response, ndp indication, 7258 * and ndp confirm. 7259 */ 7260 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, 7261 /* Unsigned 8-bit value indicating protocol used by NDP and assigned by 7262 * the Internet Assigned Numbers Authority (IANA) as per: 7263 * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml 7264 * This attribute is used and optional for ndp response, ndp indication, 7265 * and ndp confirm. 7266 */ 7267 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, 7268 /* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE. 7269 * 1:support 0:not support 7270 */ 7271 QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30, 7272 7273 /* keep last */ 7274 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, 7275 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = 7276 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, 7277 }; 7278 7279 enum qca_wlan_ndp_sub_cmd { 7280 QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, 7281 /* Command to create a NAN data path interface */ 7282 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, 7283 /* Command to delete a NAN data path interface */ 7284 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, 7285 /* Command to initiate a NAN data path session */ 7286 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, 7287 /* Command to notify if the NAN data path session was sent */ 7288 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, 7289 /* Command to respond to NAN data path session */ 7290 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, 7291 /* Command to notify on the responder about the response */ 7292 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, 7293 /* Command to initiate a NAN data path end */ 7294 QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, 7295 /* Command to notify the if end request was sent */ 7296 QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, 7297 /* Command to notify the peer about the end request */ 7298 QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, 7299 /* Command to confirm the NAN data path session is complete */ 7300 QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, 7301 /* Command to indicate the peer about the end request being received */ 7302 QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, 7303 /* Command to indicate the peer of schedule update */ 7304 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 7305 }; 7306 7307 /** 7308 * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command 7309 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD. 7310 */ 7311 enum qca_wlan_vendor_attr_nd_offload { 7312 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, 7313 /* Flag to set Neighbour Discovery offload */ 7314 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, 7315 /* Keep last */ 7316 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, 7317 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = 7318 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, 7319 }; 7320 7321 /** 7322 * enum packet_filter_sub_cmd - Packet filter sub commands 7323 */ 7324 enum packet_filter_sub_cmd { 7325 /** 7326 * Write packet filter program and/or data. The driver/firmware should 7327 * disable APF before writing into local buffer and re-enable APF after 7328 * writing is done. 7329 */ 7330 QCA_WLAN_SET_PACKET_FILTER = 1, 7331 /* Get packet filter feature capabilities from driver */ 7332 QCA_WLAN_GET_PACKET_FILTER = 2, 7333 /** 7334 * Write packet filter program and/or data. User space will send the 7335 * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command 7336 * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key 7337 * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over 7338 * enable/disable is given to user space with this command. Also, 7339 * user space sends the length of program portion in the buffer within 7340 * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH. 7341 */ 7342 QCA_WLAN_WRITE_PACKET_FILTER = 3, 7343 /* Read packet filter program and/or data */ 7344 QCA_WLAN_READ_PACKET_FILTER = 4, 7345 /* Enable APF feature */ 7346 QCA_WLAN_ENABLE_PACKET_FILTER = 5, 7347 /* Disable APF feature */ 7348 QCA_WLAN_DISABLE_PACKET_FILTER = 6, 7349 }; 7350 7351 /** 7352 * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by 7353 * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER. 7354 */ 7355 enum qca_wlan_vendor_attr_packet_filter { 7356 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, 7357 /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */ 7358 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD, 7359 /* Unsigned 32-bit value indicating the packet filter version */ 7360 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, 7361 /* Unsigned 32-bit value indicating the packet filter id */ 7362 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, 7363 /** 7364 * Unsigned 32-bit value indicating the packet filter size including 7365 * program + data. 7366 */ 7367 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, 7368 /* Unsigned 32-bit value indicating the packet filter current offset */ 7369 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, 7370 /* Program and/or data in bytes */ 7371 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, 7372 /* Unsigned 32-bit value of the length of the program section in packet 7373 * filter buffer. 7374 */ 7375 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7, 7376 7377 /* keep last */ 7378 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, 7379 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = 7380 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, 7381 }; 7382 7383 /** 7384 * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command 7385 * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE. 7386 */ 7387 enum qca_wlan_vendor_drv_info { 7388 QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, 7389 /* Maximum Message size info between firmware & HOST 7390 * Unsigned 32-bit value 7391 */ 7392 QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, 7393 /* keep last */ 7394 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, 7395 QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = 7396 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, 7397 }; 7398 7399 /** 7400 * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor 7401 * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS. 7402 */ 7403 enum qca_wlan_vendor_attr_wake_stats { 7404 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0, 7405 /* Unsigned 32-bit value indicating the total count of wake event */ 7406 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE, 7407 /* Array of individual wake count, each index representing wake reason 7408 */ 7409 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR, 7410 /* Unsigned 32-bit value representing wake count array */ 7411 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ, 7412 /* Unsigned 32-bit total wake count value of driver/fw */ 7413 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE, 7414 /* Array of wake stats of driver/fw */ 7415 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR, 7416 /* Unsigned 32-bit total wake count value of driver/fw */ 7417 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ, 7418 /* Unsigned 32-bit total wake count value of packets received */ 7419 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE, 7420 /* Unsigned 32-bit wake count value unicast packets received */ 7421 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT, 7422 /* Unsigned 32-bit wake count value multicast packets received */ 7423 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT, 7424 /* Unsigned 32-bit wake count value broadcast packets received */ 7425 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT, 7426 /* Unsigned 32-bit wake count value of ICMP packets */ 7427 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT, 7428 /* Unsigned 32-bit wake count value of ICMP6 packets */ 7429 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT, 7430 /* Unsigned 32-bit value ICMP6 router advertisement */ 7431 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA, 7432 /* Unsigned 32-bit value ICMP6 neighbor advertisement */ 7433 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA, 7434 /* Unsigned 32-bit value ICMP6 neighbor solicitation */ 7435 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS, 7436 /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */ 7437 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT, 7438 /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */ 7439 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT, 7440 /* Unsigned 32-bit wake count value of receive side multicast */ 7441 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT, 7442 /* Unsigned 32-bit wake count value of a given RSSI breach */ 7443 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT, 7444 /* Unsigned 32-bit wake count value of low RSSI */ 7445 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT, 7446 /* Unsigned 32-bit value GSCAN count */ 7447 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT, 7448 /* Unsigned 32-bit value PNO complete count */ 7449 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT, 7450 /* Unsigned 32-bit value PNO match count */ 7451 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT, 7452 /* keep last */ 7453 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, 7454 QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = 7455 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, 7456 }; 7457 7458 /** 7459 * enum qca_wlan_vendor_thermal_level - Defines various thermal levels 7460 * configured by userspace to the driver/firmware. 7461 * The values can be encapsulated in QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL or 7462 * QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_LEVEL attribute. 7463 * The driver/firmware takes actions requested by userspace such as throttling 7464 * wifi TX etc. in order to mitigate high temperature. 7465 * 7466 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE: Stop/clear all throttling actions. 7467 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT: Throttle TX lightly. 7468 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE: Throttle TX moderately. 7469 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE: Throttle TX severely. 7470 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL: Critical thermal level reached. 7471 * @QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY: Emergency thermal level reached. 7472 */ 7473 enum qca_wlan_vendor_thermal_level { 7474 QCA_WLAN_VENDOR_THERMAL_LEVEL_NONE = 0, 7475 QCA_WLAN_VENDOR_THERMAL_LEVEL_LIGHT = 1, 7476 QCA_WLAN_VENDOR_THERMAL_LEVEL_MODERATE = 2, 7477 QCA_WLAN_VENDOR_THERMAL_LEVEL_SEVERE = 3, 7478 QCA_WLAN_VENDOR_THERMAL_LEVEL_CRITICAL = 4, 7479 QCA_WLAN_VENDOR_THERMAL_LEVEL_EMERGENCY = 5, 7480 }; 7481 7482 /** 7483 * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set 7484 * cmd value. Used for NL attributes for data used by 7485 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 7486 */ 7487 enum qca_wlan_vendor_attr_thermal_cmd { 7488 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0, 7489 /* The value of command, driver will implement different operations 7490 * according to this value. It uses values defined in 7491 * enum qca_wlan_vendor_attr_thermal_cmd_type. 7492 * u32 attribute. 7493 */ 7494 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1, 7495 /* Userspace uses this attribute to configure thermal level to the 7496 * driver/firmware, or get thermal level from the driver/firmware. 7497 * Used in request or response, u32 attribute, 7498 * possible values are defined in enum qca_wlan_vendor_thermal_level. 7499 */ 7500 QCA_WLAN_VENDOR_ATTR_THERMAL_LEVEL = 2, 7501 /* Userspace uses this attribute to configure the time in which the 7502 * driver/firmware should complete applying settings it received from 7503 * userspace with QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL 7504 * command type. Used in request, u32 attribute, value is in 7505 * milliseconds. A value of zero indicates to apply the settings 7506 * immediately. The driver/firmware can delay applying the configured 7507 * thermal settings within the time specified in this attribute if 7508 * there is any critical ongoing operation. 7509 */ 7510 QCA_WLAN_VENDOR_ATTR_THERMAL_COMPLETION_WINDOW = 3, 7511 /* Nested attribute, the driver/firmware uses this attribute to report 7512 * thermal statistics of different thermal levels to userspace when 7513 * requested using the 7514 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS command 7515 * type. This attribute contains a nested array of records of thermal 7516 * statistics of multiple levels. The attributes used inside this nested 7517 * attribute are defined in enum qca_wlan_vendor_attr_thermal_stats. 7518 */ 7519 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS = 4, 7520 7521 /* keep last */ 7522 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST, 7523 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX = 7524 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1 7525 }; 7526 7527 /** 7528 * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for 7529 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd 7530 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the 7531 * thermal command types sent to driver. 7532 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to 7533 * get thermal shutdown configuration parameters for display. Parameters 7534 * responded from driver are defined in 7535 * enum qca_wlan_vendor_attr_get_thermal_params_rsp. 7536 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to 7537 * get temperature. Host should respond with a temperature data. It is defined 7538 * in enum qca_wlan_vendor_attr_thermal_get_temperature. 7539 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal 7540 * suspend action. 7541 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal 7542 * resume action. 7543 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL: Configure thermal level to 7544 * the driver/firmware. 7545 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL: Request to get the current 7546 * thermal level from the driver/firmware. The driver should respond with a 7547 * thermal level defined in enum qca_wlan_vendor_thermal_level. 7548 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS: Request to get the 7549 * current thermal statistics from the driver/firmware. The driver should 7550 * respond with statistics of all thermal levels encapsulated in the attribute 7551 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS. 7552 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS: Request to clear 7553 * the current thermal statistics for all thermal levels maintained in the 7554 * driver/firmware and start counting from zero again. 7555 */ 7556 enum qca_wlan_vendor_attr_thermal_cmd_type { 7557 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS, 7558 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE, 7559 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND, 7560 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME, 7561 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SET_LEVEL, 7562 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_LEVEL, 7563 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_THERMAL_STATS, 7564 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_CLEAR_THERMAL_STATS, 7565 }; 7566 7567 /** 7568 * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes 7569 * to get chip temperature by user. 7570 * enum values are used for NL attributes for data used by 7571 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used 7572 * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 7573 */ 7574 enum qca_wlan_vendor_attr_thermal_get_temperature { 7575 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0, 7576 /* Temperature value (degree Celsius) from driver. 7577 * u32 attribute. 7578 */ 7579 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA, 7580 7581 /* keep last */ 7582 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST, 7583 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX = 7584 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1, 7585 }; 7586 7587 /** 7588 * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes 7589 * to get configuration parameters of thermal shutdown feature. Enum values are 7590 * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data 7591 * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 7592 */ 7593 enum qca_wlan_vendor_attr_get_thermal_params_rsp { 7594 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0, 7595 /* Indicate if the thermal shutdown feature is enabled. 7596 * NLA_FLAG attribute. 7597 */ 7598 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN, 7599 /* Indicate if the auto mode is enabled. 7600 * Enable: Driver triggers the suspend/resume action. 7601 * Disable: User space triggers the suspend/resume action. 7602 * NLA_FLAG attribute. 7603 */ 7604 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN, 7605 /* Thermal resume threshold (degree Celsius). Issue the resume command 7606 * if the temperature value is lower than this threshold. 7607 * u16 attribute. 7608 */ 7609 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH, 7610 /* Thermal warning threshold (degree Celsius). FW reports temperature 7611 * to driver if it's higher than this threshold. 7612 * u16 attribute. 7613 */ 7614 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH, 7615 /* Thermal suspend threshold (degree Celsius). Issue the suspend command 7616 * if the temperature value is higher than this threshold. 7617 * u16 attribute. 7618 */ 7619 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH, 7620 /* FW reports temperature data periodically at this interval (ms). 7621 * u16 attribute. 7622 */ 7623 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE, 7624 7625 /* keep last */ 7626 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST, 7627 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX = 7628 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1, 7629 }; 7630 7631 /** 7632 * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to 7633 * report thermal events from driver to user space. 7634 * enum values are used for NL attributes for data used by 7635 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command. 7636 */ 7637 enum qca_wlan_vendor_attr_thermal_event { 7638 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0, 7639 /* Temperature value (degree Celsius) from driver. 7640 * u32 attribute. 7641 */ 7642 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE, 7643 /* Indication of resume completion from power save mode. 7644 * NLA_FLAG attribute. 7645 */ 7646 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE, 7647 /* Thermal level from the driver. 7648 * u32 attribute. Possible values are defined in 7649 * enum qca_wlan_vendor_thermal_level. 7650 */ 7651 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_LEVEL = 3, 7652 7653 /* keep last */ 7654 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST, 7655 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX = 7656 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1, 7657 }; 7658 7659 /** 7660 * enum qca_wlan_vendor_attr_thermal_stats - vendor subcmd attributes 7661 * to get thermal status from the driver/firmware. 7662 * enum values are used for NL attributes encapsulated inside the 7663 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS nested attribute. 7664 * 7665 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE: Minimum temperature 7666 * of a thermal level in Celsius. u32 size. 7667 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE: Maximum temperature 7668 * of a thermal level in Celsius. u32 size. 7669 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME: The total time spent on each 7670 * thermal level in milliseconds. u32 size. 7671 * QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER: Indicates the number 7672 * of times the temperature crossed into the temperature range defined by the 7673 * thermal level from both higher and lower directions. u32 size. 7674 */ 7675 enum qca_wlan_vendor_attr_thermal_stats { 7676 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_INVALID = 0, 7677 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MIN_TEMPERATURE, 7678 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX_TEMPERATURE, 7679 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_DWELL_TIME, 7680 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_TEMP_LEVEL_COUNTER, 7681 7682 /* keep last */ 7683 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST, 7684 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_MAX = 7685 QCA_WLAN_VENDOR_ATTR_THERMAL_STATS_AFTER_LAST - 1, 7686 }; 7687 7688 /** 7689 * enum he_fragmentation_val - HE fragmentation support values 7690 * Indicates level of dynamic fragmentation that is supported by 7691 * a STA as a recipient. 7692 * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2 7693 * (HE MAC Capabilities Information field) and are used in HE Capabilities 7694 * element to advertise the support. These values are validated in the driver 7695 * to check the device capability and advertised in the HE Capabilities 7696 * element. These values are used to configure testbed device to allow the 7697 * advertised hardware capabilities to be downgraded for testing purposes. 7698 * 7699 * @HE_FRAG_DISABLE: no support for dynamic fragmentation 7700 * @HE_FRAG_LEVEL1: support for dynamic fragments that are 7701 * contained within an MPDU or S-MPDU, no support for dynamic fragments 7702 * within an A-MPDU that is not an S-MPDU. 7703 * @HE_FRAG_LEVEL2: support for dynamic fragments that are 7704 * contained within an MPDU or S-MPDU and support for up to one dynamic 7705 * fragment for each MSDU, each A-MSDU if supported by the recipient, and 7706 * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an 7707 * MPDU or S-MPDU. 7708 * @HE_FRAG_LEVEL3: support for dynamic fragments that are 7709 * contained within an MPDU or S-MPDU and support for multiple dynamic 7710 * fragments for each MSDU and for each A-MSDU if supported by the 7711 * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic 7712 * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. 7713 */ 7714 enum he_fragmentation_val { 7715 HE_FRAG_DISABLE, 7716 HE_FRAG_LEVEL1, 7717 HE_FRAG_LEVEL2, 7718 HE_FRAG_LEVEL3, 7719 }; 7720 7721 /** 7722 * enum he_mcs_config - HE MCS support configuration 7723 * 7724 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. 7725 * These values are used in driver to configure the HE MCS map to advertise 7726 * Tx/Rx MCS map in HE capability and these values are applied for all the 7727 * streams supported by the device. To configure MCS for different bandwidths, 7728 * vendor command needs to be sent using this attribute with appropriate value. 7729 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS 7730 * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11 7731 * send this command using HE MCS config attribute with value HE_160_MCS0_11. 7732 * These values are used to configure testbed device to allow the advertised 7733 * hardware capabilities to be downgraded for testing purposes. The enum values 7734 * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and 7735 * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map. 7736 * These values are validated in the driver before setting the MCS map and 7737 * driver returns error if the input is other than these enum values. 7738 * 7739 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7 7740 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9 7741 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11 7742 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7 7743 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9 7744 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11 7745 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7 7746 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9 7747 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11 7748 */ 7749 enum he_mcs_config { 7750 HE_80_MCS0_7 = 0, 7751 HE_80_MCS0_9 = 1, 7752 HE_80_MCS0_11 = 2, 7753 HE_160_MCS0_7 = 4, 7754 HE_160_MCS0_9 = 5, 7755 HE_160_MCS0_11 = 6, 7756 HE_80P80_MCS0_7 = 8, 7757 HE_80P80_MCS0_9 = 9, 7758 HE_80P80_MCS0_11 = 10, 7759 }; 7760 7761 /** 7762 * enum qca_wlan_ba_session_config - BA session configuration 7763 * 7764 * Indicates the configuration values for BA session configuration attribute. 7765 * 7766 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. 7767 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. 7768 */ 7769 enum qca_wlan_ba_session_config { 7770 QCA_WLAN_ADD_BA = 1, 7771 QCA_WLAN_DELETE_BA = 2, 7772 }; 7773 7774 /** 7775 * enum qca_wlan_ac_type - Access category type 7776 * 7777 * Indicates the access category type value. 7778 * 7779 * @QCA_WLAN_AC_BE: BE access category 7780 * @QCA_WLAN_AC_BK: BK access category 7781 * @QCA_WLAN_AC_VI: VI access category 7782 * @QCA_WLAN_AC_VO: VO access category 7783 * @QCA_WLAN_AC_ALL: All ACs 7784 */ 7785 enum qca_wlan_ac_type { 7786 QCA_WLAN_AC_BE = 0, 7787 QCA_WLAN_AC_BK = 1, 7788 QCA_WLAN_AC_VI = 2, 7789 QCA_WLAN_AC_VO = 3, 7790 QCA_WLAN_AC_ALL = 4, 7791 }; 7792 7793 /** 7794 * enum qca_wlan_he_ltf_cfg - HE LTF configuration 7795 * 7796 * Indicates the HE LTF configuration value. 7797 * 7798 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF, 7799 * based on the GI setting 7800 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF 7801 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF 7802 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF 7803 */ 7804 enum qca_wlan_he_ltf_cfg { 7805 QCA_WLAN_HE_LTF_AUTO = 0, 7806 QCA_WLAN_HE_LTF_1X = 1, 7807 QCA_WLAN_HE_LTF_2X = 2, 7808 QCA_WLAN_HE_LTF_4X = 3, 7809 }; 7810 7811 /** 7812 * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration 7813 * 7814 * Indicates the HE trigger frame MAC padding duration value. 7815 * 7816 * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to 7817 * process the trigger frame. 7818 * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for 7819 * trigger frame. 7820 * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for 7821 * trigger frame. 7822 */ 7823 enum qca_wlan_he_mac_padding_dur { 7824 QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, 7825 QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, 7826 QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, 7827 }; 7828 7829 /** 7830 * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration 7831 * 7832 * Indicates the HE Operating mode control channel width setting value. 7833 * 7834 * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz 7835 * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz 7836 * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz 7837 * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz 7838 */ 7839 enum qca_wlan_he_om_ctrl_ch_bw { 7840 QCA_WLAN_HE_OM_CTRL_BW_20M = 0, 7841 QCA_WLAN_HE_OM_CTRL_BW_40M = 1, 7842 QCA_WLAN_HE_OM_CTRL_BW_80M = 2, 7843 QCA_WLAN_HE_OM_CTRL_BW_160M = 3, 7844 }; 7845 7846 /** 7847 * enum qca_wlan_keep_alive_data_type - Keep alive data type configuration 7848 * 7849 * Indicates the frame types to use for keep alive data. 7850 * 7851 * @QCA_WLAN_KEEP_ALIVE_DEFAULT: Driver default type used for keep alive. 7852 * @QCA_WLAN_KEEP_ALIVE_DATA: Data frame type for keep alive. 7853 * @QCA_WLAN_KEEP_ALIVE_MGMT: Management frame type for keep alive. 7854 */ 7855 enum qca_wlan_keep_alive_data_type { 7856 QCA_WLAN_KEEP_ALIVE_DEFAULT = 0, 7857 QCA_WLAN_KEEP_ALIVE_DATA = 1, 7858 QCA_WLAN_KEEP_ALIVE_MGMT = 2, 7859 }; 7860 7861 /** 7862 * enum qca_wlan_vendor_attr_he_omi_tx: Represents attributes for 7863 * HE operating mode control transmit request. These attributes are 7864 * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX and 7865 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 7866 * 7867 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value 7868 * indicates the maximum number of spatial streams, NSS, that the STA 7869 * supports in reception for PPDU bandwidths less than or equal to 80 MHz 7870 * and is set to NSS - 1. 7871 * 7872 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value 7873 * indicates the operating channel width supported by the STA for both 7874 * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. 7875 * 7876 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value 7877 * indicates the all trigger based UL MU operations by the STA. 7878 * 0 - UL MU operations are enabled by the STA. 7879 * 1 - All triggered UL MU transmissions are suspended by the STA. 7880 * 7881 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value 7882 * indicates the maximum number of space-time streams, NSTS, that 7883 * the STA supports in transmission and is set to NSTS - 1. 7884 * 7885 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE: 8-bit unsigned value 7886 * combined with the UL MU Disable subfield and the recipient's setting 7887 * of the OM Control UL MU Data Disable RX Support subfield in the HE MAC 7888 * capabilities to determine which HE TB PPDUs are possible by the 7889 * STA to transmit. 7890 * 0 - UL MU data operations are enabled by the STA. 7891 * 1 - Determine which HE TB PPDU types are allowed by the STA if UL MU disable 7892 * bit is not set, else UL MU Tx is suspended. 7893 * 7894 */ 7895 enum qca_wlan_vendor_attr_he_omi_tx { 7896 QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, 7897 QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, 7898 QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, 7899 QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, 7900 QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, 7901 QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE = 5, 7902 7903 /* keep last */ 7904 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST, 7905 QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX = 7906 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1, 7907 }; 7908 7909 /** 7910 * enum qca_wlan_vendor_phy_mode - Different PHY modes 7911 * These values are used with %QCA_WLAN_VENDOR_ATTR_CONFIG_PHY_MODE. 7912 * 7913 * @QCA_WLAN_VENDOR_PHY_MODE_AUTO: autoselect 7914 * @QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO: 2.4 GHz 802.11b/g/n/ax autoselect 7915 * @QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO: 5 GHz 802.11a/n/ac/ax autoselect 7916 * @QCA_WLAN_VENDOR_PHY_MODE_11A: 5 GHz, OFDM 7917 * @QCA_WLAN_VENDOR_PHY_MODE_11B: 2.4 GHz, CCK 7918 * @QCA_WLAN_VENDOR_PHY_MODE_11G: 2.4 GHz, OFDM 7919 * @QCA_WLAN_VENDOR_PHY_MODE_11AGN: Support 802.11n in both 2.4 GHz and 5 GHz 7920 * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20: 2.4 GHz, HT20 7921 * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS: 2.4 GHz, HT40 (ext ch +1) 7922 * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS: 2.4 GHz, HT40 (ext ch -1) 7923 * @QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40: 2.4 GHz, Auto HT40 7924 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20: 5 GHz, HT20 7925 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS: 5 GHz, HT40 (ext ch +1) 7926 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS: 5 GHz, HT40 (ext ch -1) 7927 * @QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40: 5 GHz, Auto HT40 7928 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20: 5 GHz, VHT20 7929 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS: 5 GHz, VHT40 (Ext ch +1) 7930 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS: 5 GHz VHT40 (Ext ch -1) 7931 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40: 5 GHz, VHT40 7932 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80: 5 GHz, VHT80 7933 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80: 5 GHz, VHT80+80 7934 * @QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160: 5 GHz, VHT160 7935 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20: HE20 7936 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40: HE40 7937 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS: HE40 (ext ch +1) 7938 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS: HE40 (ext ch -1) 7939 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80: HE80 7940 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80: HE 80P80 7941 * @QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160: HE160 7942 */ 7943 enum qca_wlan_vendor_phy_mode { 7944 QCA_WLAN_VENDOR_PHY_MODE_AUTO = 0, 7945 QCA_WLAN_VENDOR_PHY_MODE_2G_AUTO = 1, 7946 QCA_WLAN_VENDOR_PHY_MODE_5G_AUTO = 2, 7947 QCA_WLAN_VENDOR_PHY_MODE_11A = 3, 7948 QCA_WLAN_VENDOR_PHY_MODE_11B = 4, 7949 QCA_WLAN_VENDOR_PHY_MODE_11G = 5, 7950 QCA_WLAN_VENDOR_PHY_MODE_11AGN = 6, 7951 QCA_WLAN_VENDOR_PHY_MODE_11NG_HT20 = 7, 7952 QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40PLUS = 8, 7953 QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40MINUS = 9, 7954 QCA_WLAN_VENDOR_PHY_MODE_11NG_HT40 = 10, 7955 QCA_WLAN_VENDOR_PHY_MODE_11NA_HT20 = 11, 7956 QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40PLUS = 12, 7957 QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40MINUS = 13, 7958 QCA_WLAN_VENDOR_PHY_MODE_11NA_HT40 = 14, 7959 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT20 = 15, 7960 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40PLUS = 16, 7961 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40MINUS = 17, 7962 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT40 = 18, 7963 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80 = 19, 7964 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT80P80 = 20, 7965 QCA_WLAN_VENDOR_PHY_MODE_11AC_VHT160 = 21, 7966 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE20 = 22, 7967 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40 = 23, 7968 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40PLUS = 24, 7969 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE40MINUS = 25, 7970 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80 = 26, 7971 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE80P80 = 27, 7972 QCA_WLAN_VENDOR_PHY_MODE_11AX_HE160 = 28, 7973 }; 7974 7975 /* Attributes for data used by 7976 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION 7977 */ 7978 enum qca_wlan_vendor_attr_wifi_test_config { 7979 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, 7980 /* 8-bit unsigned value to configure the driver to enable/disable 7981 * WMM feature. This attribute is used to configure testbed device. 7982 * 1-enable, 0-disable 7983 */ 7984 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, 7985 7986 /* 8-bit unsigned value to configure the driver to accept/reject 7987 * the addba request from peer. This attribute is used to configure 7988 * the testbed device. 7989 * 1-accept addba, 0-reject addba 7990 */ 7991 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, 7992 7993 /* 8-bit unsigned value to configure the driver to send or not to 7994 * send the addba request to peer. 7995 * This attribute is used to configure the testbed device. 7996 * 1-send addba, 0-do not send addba 7997 */ 7998 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, 7999 8000 /* 8-bit unsigned value to indicate the HE fragmentation support. 8001 * Uses enum he_fragmentation_val values. 8002 * This attribute is used to configure the testbed device to 8003 * allow the advertised hardware capabilities to be downgraded 8004 * for testing purposes. 8005 */ 8006 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, 8007 8008 /* 8-bit unsigned value to indicate the HE MCS support. 8009 * Uses enum he_mcs_config values. 8010 * This attribute is used to configure the testbed device to 8011 * allow the advertised hardware capabilities to be downgraded 8012 * for testing purposes. 8013 */ 8014 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, 8015 8016 /* 8-bit unsigned value to configure the driver to allow or not to 8017 * allow the connection with WEP/TKIP in HT/VHT/HE modes. 8018 * This attribute is used to configure the testbed device. 8019 * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP. 8020 */ 8021 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, 8022 8023 /* 8-bit unsigned value to configure the driver to add a 8024 * new BA session or delete the existing BA session for 8025 * given TID. ADDBA command uses the buffer size and TID 8026 * configuration if user specifies the values else default 8027 * value for buffer size is used for all TIDs if the TID 8028 * also not specified. For DEL_BA command TID value is 8029 * required to process the command. 8030 * Uses enum qca_wlan_ba_session_config values. 8031 * This attribute is used to configure the testbed device. 8032 */ 8033 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, 8034 8035 /* 16-bit unsigned value to configure the buffer size in addba 8036 * request and response frames. 8037 * This attribute is used to configure the testbed device. 8038 * The range of the value is 0 to 256. 8039 */ 8040 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, 8041 8042 /* 8-bit unsigned value to configure the buffer size in addba 8043 * request and response frames. 8044 * This attribute is used to configure the testbed device. 8045 */ 8046 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, 8047 8048 /* 8-bit unsigned value to configure the no ack policy. 8049 * To configure no ack policy, access category value is 8050 * required to process the command. 8051 * This attribute is used to configure the testbed device. 8052 * 1 - enable no ack, 0 - disable no ack. 8053 */ 8054 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, 8055 8056 /* 8-bit unsigned value to configure the AC for no ack policy 8057 * This attribute is used to configure the testbed device. 8058 * Uses the enum qca_wlan_ac_type values. 8059 */ 8060 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, 8061 8062 /* 8-bit unsigned value to configure the HE LTF 8063 * This attribute is used to configure the testbed device. 8064 * Uses the enum qca_wlan_he_ltf_cfg values. 8065 */ 8066 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, 8067 8068 /* 8-bit unsigned value to configure the tx beamformee. 8069 * This attribute is used to configure the testbed device. 8070 * 1-enable, 0-disable. 8071 */ 8072 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, 8073 8074 /* 8-bit unsigned value to configure the tx beamformee number 8075 * of space-time streams. 8076 * This attribute is used to configure the testbed device. 8077 * The range of the value is 0 to 8. 8078 */ 8079 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, 8080 8081 /* 8-bit unsigned value to configure the MU EDCA params for given AC 8082 * This attribute is used to configure the testbed device. 8083 * Uses the enum qca_wlan_ac_type values. 8084 */ 8085 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, 8086 8087 /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC 8088 * To configure MU EDCA AIFSN value, MU EDCA access category value 8089 * is required to process the command. 8090 * This attribute is used to configure the testbed device. 8091 */ 8092 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, 8093 8094 /* 8-bit unsigned value to configure the MU EDCA ECW min value for 8095 * given AC. 8096 * To configure MU EDCA ECW min value, MU EDCA access category value 8097 * is required to process the command. 8098 * This attribute is used to configure the testbed device. 8099 */ 8100 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, 8101 8102 /* 8-bit unsigned value to configure the MU EDCA ECW max value for 8103 * given AC. 8104 * To configure MU EDCA ECW max value, MU EDCA access category value 8105 * is required to process the command. 8106 * This attribute is used to configure the testbed device. 8107 */ 8108 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, 8109 8110 /* 8-bit unsigned value to configure the MU EDCA timer for given AC 8111 * To configure MU EDCA timer value, MU EDCA access category value 8112 * is required to process the command. 8113 * This attribute is used to configure the testbed device. 8114 */ 8115 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, 8116 8117 /* 8-bit unsigned value to configure the HE trigger frame MAC padding 8118 * duration. 8119 * This attribute is used to configure the testbed device. 8120 * Uses the enum qca_wlan_he_mac_padding_dur values. 8121 */ 8122 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, 8123 8124 /* 8-bit unsigned value to override the MU EDCA params to defaults 8125 * regardless of the AP beacon MU EDCA params. If it is enabled use 8126 * the default values else use the MU EDCA params from AP beacon. 8127 * This attribute is used to configure the testbed device. 8128 * 1-enable, 0-disable. 8129 */ 8130 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, 8131 8132 /* 8-bit unsigned value to configure the support for receiving 8133 * an MPDU that contains an operating mode control subfield. 8134 * This attribute is used to configure the testbed device. 8135 * 1-enable, 0-disable. 8136 */ 8137 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, 8138 8139 /* Nested attribute values required to setup the TWT session. 8140 * enum qca_wlan_vendor_attr_twt_setup provides the necessary 8141 * information to set up the session. It contains broadcast flags, 8142 * set_up flags, trigger value, flow type, flow ID, wake interval 8143 * exponent, protection, target wake time, wake duration, wake interval 8144 * mantissa. These nested attributes are used to setup a host triggered 8145 * TWT session. 8146 */ 8147 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, 8148 8149 /* This nested attribute is used to terminate the current TWT session. 8150 * It does not currently carry any attributes. 8151 */ 8152 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, 8153 8154 /* This nested attribute is used to suspend the current TWT session. 8155 * It does not currently carry any attributes. 8156 */ 8157 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, 8158 8159 /* Nested attribute values to indicate the request for resume. 8160 * This attribute is used to resume the TWT session. 8161 * enum qca_wlan_vendor_attr_twt_resume provides the necessary 8162 * parameters required to resume the TWT session. 8163 */ 8164 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, 8165 8166 /* 8-bit unsigned value to set the HE operating mode control 8167 * (OM CTRL) Channel Width subfield. 8168 * The Channel Width subfield indicates the operating channel width 8169 * supported by the STA for both reception and transmission. 8170 * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. 8171 * This setting is cleared with the 8172 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 8173 * flag attribute to reset defaults. 8174 * This attribute is used to configure the testbed device. 8175 */ 8176 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, 8177 8178 /* 8-bit unsigned value to configure the number of spatial 8179 * streams in HE operating mode control field. 8180 * This setting is cleared with the 8181 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 8182 * flag attribute to reset defaults. 8183 * This attribute is used to configure the testbed device. 8184 */ 8185 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, 8186 8187 /* Flag attribute to configure the UL MU disable bit in 8188 * HE operating mode control field. 8189 * This setting is cleared with the 8190 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 8191 * flag attribute to reset defaults. 8192 * This attribute is used to configure the testbed device. 8193 */ 8194 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, 8195 8196 /* Flag attribute to clear the previously set HE operating mode 8197 * control field configuration. 8198 * This attribute is used to configure the testbed device to reset 8199 * defaults to clear any previously set HE operating mode control 8200 * field configuration. 8201 */ 8202 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, 8203 8204 /* 8-bit unsigned value to configure HE single user PPDU 8205 * transmission. By default this setting is disabled and it 8206 * is disabled in the reset defaults of the device configuration. 8207 * This attribute is used to configure the testbed device. 8208 * 1-enable, 0-disable 8209 */ 8210 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, 8211 8212 /* 8-bit unsigned value to configure action frame transmission 8213 * in HE trigger based PPDU transmission. 8214 * By default this setting is disabled and it is disabled in 8215 * the reset defaults of the device configuration. 8216 * This attribute is used to configure the testbed device. 8217 * 1-enable, 0-disable 8218 */ 8219 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, 8220 8221 /* Nested attribute to indicate HE operating mode control field 8222 * transmission. It contains operating mode control field Nss, 8223 * channel bandwidth, Tx Nsts and UL MU disable attributes. 8224 * These nested attributes are used to send HE operating mode control 8225 * with configured values. 8226 * Uses the enum qca_wlan_vendor_attr_he_omi_tx attributes. 8227 * This attribute is used to configure the testbed device. 8228 */ 8229 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX = 33, 8230 8231 /* 8-bit unsigned value to configure +HTC_HE support to indicate the 8232 * support for the reception of a frame that carries an HE variant 8233 * HT Control field. 8234 * This attribute is used to configure the testbed device. 8235 * 1-enable, 0-disable 8236 */ 8237 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, 8238 8239 /* 8-bit unsigned value to configure VHT support in 2.4G band. 8240 * This attribute is used to configure the testbed device. 8241 * 1-enable, 0-disable 8242 */ 8243 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_2G_VHT = 35, 8244 8245 /* 8-bit unsigned value to configure HE testbed defaults. 8246 * This attribute is used to configure the testbed device. 8247 * 1-set the device HE capabilities to testbed defaults. 8248 * 0-reset the device HE capabilities to supported config. 8249 */ 8250 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_HE_TESTBED_DEFAULTS = 36, 8251 8252 /* 8-bit unsigned value to configure TWT request support. 8253 * This attribute is used to configure the testbed device. 8254 * 1-enable, 0-disable. 8255 */ 8256 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37, 8257 8258 /* 8-bit unsigned value to configure protection for Management 8259 * frames when PMF is enabled for the association. 8260 * This attribute is used to configure the testbed device. 8261 * 0-use the correct key, 1-use an incorrect key, 2-disable protection. 8262 */ 8263 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PMF_PROTECTION = 38, 8264 8265 /* Flag attribute to inject Disassociation frame to the connected AP. 8266 * This attribute is used to configure the testbed device. 8267 */ 8268 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISASSOC_TX = 39, 8269 8270 /* 8-bit unsigned value to configure an override for the RSNXE Used 8271 * subfield in the MIC control field of the FTE in FT Reassociation 8272 * Request frame. 8273 * 0 - Default behavior, 1 - override with 1, 2 - override with 0. 8274 * This attribute is used to configure the testbed device. 8275 * This attribute can be configured only when STA is in associated state 8276 * and the configuration is valid until the disconnection. 8277 */ 8278 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FT_REASSOCREQ_RSNXE_USED = 40, 8279 8280 /* 8-bit unsigned value to configure the driver to ignore CSA (Channel 8281 * Switch Announcement) when STA is in connected state. 8282 * 0 - Default behavior, 1 - Ignore CSA. 8283 * This attribute is used to configure the testbed device. 8284 * This attribute can be configured only when STA is in associated state 8285 * and the configuration is valid until the disconnection. 8286 */ 8287 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_CSA = 41, 8288 8289 /* Nested attribute values required to configure OCI (Operating Channel 8290 * Information). Attributes defined in enum 8291 * qca_wlan_vendor_attr_oci_override are nested within this attribute. 8292 * This attribute is used to configure the testbed device. 8293 * This attribute can be configured only when STA is in associated state 8294 * and the configuration is valid until the disconnection. 8295 */ 8296 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE = 42, 8297 8298 /* 8-bit unsigned value to configure the driver/firmware to ignore SA 8299 * Query timeout. If this configuration is enabled STA shall not send 8300 * Deauthentication frmae when SA Query times out (mainly, after a 8301 * channel switch when OCV is enabled). 8302 * 0 - Default behavior, 1 - Ignore SA Query timeout. 8303 * This attribute is used to configure the testbed device. 8304 * This attribute can be configured only when STA is in associated state 8305 * and the configuration is valid until the disconnection. 8306 */ 8307 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_SA_QUERY_TIMEOUT = 43, 8308 8309 /* 8-bit unsigned value to configure the driver/firmware to start or 8310 * stop transmitting FILS discovery frames. 8311 * 0 - Stop transmitting FILS discovery frames 8312 * 1 - Start transmitting FILS discovery frames 8313 * This attribute is used to configure the testbed device. 8314 * This attribute can be configured only in AP mode and the 8315 * configuration is valid until AP restart. 8316 */ 8317 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FILS_DISCOVERY_FRAMES_TX = 44, 8318 8319 /* 8-bit unsigned value to configure the driver/firmware to enable or 8320 * disable full bandwidth UL MU-MIMO subfield in the HE PHY capabilities 8321 * information field. 8322 * 0 - Disable full bandwidth UL MU-MIMO subfield 8323 * 1 - Enable full bandwidth UL MU-MIMO subfield 8324 * This attribute is used to configure the testbed device. 8325 */ 8326 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_FULL_BW_UL_MU_MIMO = 45, 8327 8328 /* 16-bit unsigned value to configure the driver with a specific BSS 8329 * max idle period to advertise in the BSS Max Idle Period element 8330 * (IEEE Std 802.11-2016, 9.4.2.79) in (Re)Association Request frames. 8331 * This attribute is used to configure the testbed device. 8332 */ 8333 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD = 46, 8334 8335 /* 8-bit unsigned value to configure the driver to use only RU 242 tone 8336 * for data transmission. 8337 * 0 - Default behavior, 1 - Configure RU 242 tone for data Tx. 8338 * This attribute is used to configure the testbed device. 8339 */ 8340 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RU_242_TONE_TX = 47, 8341 8342 /* 8-bit unsigned value to configure the driver to disable data and 8343 * management response frame transmission to test the BSS max idle 8344 * feature. 8345 * 0 - Default behavior, 1 - Disable data and management response Tx. 8346 * This attribute is used to configure the testbed device. 8347 */ 8348 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_DISABLE_DATA_MGMT_RSP_TX = 48, 8349 8350 /* 8-bit unsigned value to configure the driver/firmware to enable or 8351 * disable Punctured Preamble Rx subfield in the HE PHY capabilities 8352 * information field. 8353 * 0 - Disable Punctured Preamble Rx subfield 8354 * 1 - Enable Punctured Preamble Rx subfield 8355 * This attribute is used to configure the testbed device. 8356 */ 8357 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_PUNCTURED_PREAMBLE_RX = 49, 8358 8359 /* 8-bit unsigned value to configure the driver to ignore the SAE H2E 8360 * requirement mismatch for 6 GHz connection. 8361 * 0 - Default behavior, 1 - Ignore SAE H2E requirement mismatch. 8362 * This attribute is used to configure the testbed device. 8363 */ 8364 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_IGNORE_H2E_RSNXE = 50, 8365 8366 /* 8-bit unsigned value to configure the driver to allow 6 GHz 8367 * connection with all security modes. 8368 * 0 - Default behavior, 1 - Allow 6 GHz connection with all security 8369 * modes. 8370 * This attribute is used for testing purposes. 8371 */ 8372 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_6GHZ_SECURITY_TEST_MODE = 51, 8373 8374 /* 8-bit unsigned value to configure the driver to transmit data with 8375 * ER SU PPDU type. 8376 * 8377 * 0 - Default behavior, 1 - Enable ER SU PPDU type TX. 8378 * This attribute is used for testing purposes. 8379 */ 8380 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ER_SU_PPDU_TYPE = 52, 8381 8382 /* 8-bit unsigned value to configure the driver to use Data or 8383 * Management frame type for keep alive data. 8384 * Uses enum qca_wlan_keep_alive_data_type values. 8385 * 8386 * This attribute is used for testing purposes. 8387 */ 8388 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_KEEP_ALIVE_FRAME_TYPE = 53, 8389 8390 /* 8-bit unsigned value to configure the driver to use scan request 8391 * BSSID value in Probe Request frame RA(A1) during the scan. The 8392 * driver saves this configuration and applies this setting to all user 8393 * space scan requests until the setting is cleared. If this 8394 * configuration is set, the driver uses the BSSID value from the scan 8395 * request to set the RA(A1) in the Probe Request frames during the 8396 * scan. 8397 * 8398 * 0 - Default behavior uses the broadcast RA in Probe Request frames. 8399 * 1 - Uses the scan request BSSID in RA in Probe Request frames. 8400 * This attribute is used for testing purposes. 8401 */ 8402 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_USE_BSSID_IN_PROBE_REQ_RA = 54, 8403 8404 /* 8-bit unsigned value to configure the driver to enable/disable the 8405 * BSS max idle period support. 8406 * 8407 * 0 - Disable the BSS max idle support. 8408 * 1 - Enable the BSS max idle support. 8409 * This attribute is used for testing purposes. 8410 */ 8411 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BSS_MAX_IDLE_PERIOD_ENABLE = 55, 8412 8413 /* 8-bit unsigned value to configure the driver/firmware to enable or 8414 * disable Rx control frame to MultiBSS subfield in the HE MAC 8415 * capabilities information field. 8416 * 0 - Disable Rx control frame to MultiBSS subfield 8417 * 1 - Enable Rx control frame to MultiBSS subfield 8418 * This attribute is used to configure the testbed device. 8419 */ 8420 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_RX_CTRL_FRAME_TO_MBSS = 56, 8421 8422 /* 8-bit unsigned value to configure the driver/firmware to enable or 8423 * disable Broadcast TWT support subfield in the HE MAC capabilities 8424 * information field. 8425 * 0 - Disable Broadcast TWT support subfield 8426 * 1 - Enable Broadcast TWT support subfield 8427 * This attribute is used to configure the testbed device. 8428 */ 8429 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BCAST_TWT_SUPPORT = 57, 8430 8431 /* keep last */ 8432 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, 8433 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = 8434 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, 8435 }; 8436 8437 /** 8438 * enum qca_wlan_twt_operation - Operation of the config TWT request 8439 * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION. 8440 * The response for the respective operations can be either synchronous or 8441 * asynchronous (wherever specified). If synchronous, the response to this 8442 * operation is obtained in the corresponding vendor command reply to the user 8443 * space. For the asynchronous case the response is obtained as an event with 8444 * the same operation type. 8445 * 8446 * Drivers shall support either of these modes but not both simultaneously. 8447 * This support for asynchronous mode is advertised through the flag 8448 * QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT. If this flag is not advertised, 8449 * the driver shall support synchronous mode. 8450 * 8451 * @QCA_WLAN_TWT_SET: Setup a TWT session. Required parameters are configured 8452 * through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum 8453 * qca_wlan_vendor_attr_twt_setup. Depending upon the 8454 * @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, this is either a 8455 * synchronous or asynchronous operation. 8456 * 8457 * @QCA_WLAN_TWT_GET: Get the configured TWT parameters. Required parameters are 8458 * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum 8459 * qca_wlan_vendor_attr_twt_setup. This is a synchronous operation. 8460 * 8461 * @QCA_WLAN_TWT_TERMINATE: Terminate the TWT session. Required parameters are 8462 * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum 8463 * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. 8464 * This terminate can either get triggered by the user space or can as well be 8465 * a notification from the firmware if it initiates a terminate. 8466 * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, 8467 * the request from user space can either be a synchronous or asynchronous 8468 * operation. 8469 * 8470 * @QCA_WLAN_TWT_SUSPEND: Suspend the TWT session. Required parameters are 8471 * obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum 8472 * qca_wlan_vendor_attr_twt_setup. Valid only after the TWT session is setup. 8473 * Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT capability, 8474 * this is either a synchronous or asynchronous operation. 8475 * 8476 * @QCA_WLAN_TWT_RESUME: Resume the TWT session. Required parameters are 8477 * configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the enum 8478 * qca_wlan_vendor_attr_twt_resume. Valid only after the TWT session is setup. 8479 * This can as well be a notification from the firmware on a QCA_WLAN_TWT_NUDGE 8480 * request. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT 8481 * capability, this is either a synchronous or asynchronous operation. 8482 * 8483 * @QCA_WLAN_TWT_NUDGE: Suspend and resume the TWT session. TWT nudge is a 8484 * combination of suspend and resume in a single request. Required parameters 8485 * are configured through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refers the 8486 * enum qca_wlan_vendor_attr_twt_nudge. Valid only after the TWT session is 8487 * setup. Depending upon the @QCA_WLAN_VENDOR_FEATURE_TWT_ASYNC_SUPPORT 8488 * capability, this is either a synchronous or asynchronous operation. 8489 * 8490 * @QCA_WLAN_TWT_GET_STATS: Get the TWT session traffic statistics information. 8491 * Refers the enum qca_wlan_vendor_attr_twt_stats. Valid only after the TWT 8492 * session is setup. It's a synchronous operation. 8493 * 8494 * @QCA_WLAN_TWT_CLEAR_STATS: Clear TWT session traffic statistics information. 8495 * Valid only after the TWT session is setup. It's a synchronous operation. 8496 * 8497 * @QCA_WLAN_TWT_GET_CAPABILITIES: Get TWT capabilities of this device and its 8498 * peer. Refers the enum qca_wlan_vendor_attr_twt_capability. It's a synchronous 8499 * operation. 8500 * 8501 * @QCA_WLAN_TWT_SETUP_READY_NOTIFY: Notify userspace that the firmare is 8502 * ready for a new TWT session setup after it issued a TWT teardown. 8503 * 8504 * @QCA_WLAN_TWT_SET_PARAM: Configure TWT related parameters. Required 8505 * parameters are obtained through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. Refer 8506 * the enum qca_wlan_vendor_attr_twt_set_param. 8507 */ 8508 enum qca_wlan_twt_operation { 8509 QCA_WLAN_TWT_SET = 0, 8510 QCA_WLAN_TWT_GET = 1, 8511 QCA_WLAN_TWT_TERMINATE = 2, 8512 QCA_WLAN_TWT_SUSPEND = 3, 8513 QCA_WLAN_TWT_RESUME = 4, 8514 QCA_WLAN_TWT_NUDGE = 5, 8515 QCA_WLAN_TWT_GET_STATS = 6, 8516 QCA_WLAN_TWT_CLEAR_STATS = 7, 8517 QCA_WLAN_TWT_GET_CAPABILITIES = 8, 8518 QCA_WLAN_TWT_SETUP_READY_NOTIFY = 9, 8519 QCA_WLAN_TWT_SET_PARAM = 10, 8520 }; 8521 8522 /** 8523 * enum qca_wlan_vendor_attr_config_twt: Defines attributes used by 8524 * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 8525 * 8526 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION: u8 attribute. Specify the TWT 8527 * operation of this request. Possible values are defined in enum 8528 * qca_wlan_twt_operation. The parameters for the respective operation is 8529 * specified through QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS. 8530 * 8531 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS: Nested attribute representing the 8532 * parameters configured for TWT. These parameters are represented by 8533 * enum qca_wlan_vendor_attr_twt_setup, enum qca_wlan_vendor_attr_twt_resume, 8534 * enum qca_wlan_vendor_attr_twt_set_param, or 8535 * enum qca_wlan_vendor_attr_twt_stats based on the operation. 8536 */ 8537 enum qca_wlan_vendor_attr_config_twt { 8538 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_INVALID = 0, 8539 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION = 1, 8540 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_PARAMS = 2, 8541 8542 /* keep last */ 8543 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST, 8544 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_MAX = 8545 QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_AFTER_LAST - 1, 8546 }; 8547 8548 /** 8549 * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command 8550 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 8551 * The user can add/delete the filter by specifying the BSSID/STA MAC address in 8552 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in 8553 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in 8554 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the 8555 * statistics of an unassociated station by specifying the MAC address in 8556 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in 8557 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in 8558 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get 8559 * the statistics of all unassociated stations by specifying the Broadcast MAC 8560 * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with 8561 * above procedure. In the response, driver shall specify statistics 8562 * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS. 8563 */ 8564 enum qca_wlan_vendor_attr_bss_filter { 8565 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0, 8566 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1, 8567 /* Other BSS filter type, unsigned 8 bit value. One of the values 8568 * in enum qca_wlan_vendor_bss_filter_type. 8569 */ 8570 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2, 8571 /* Other BSS filter action, unsigned 8 bit value. One of the values 8572 * in enum qca_wlan_vendor_bss_filter_action. 8573 */ 8574 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3, 8575 /* Array of nested attributes where each entry is the statistics 8576 * information of the specified station that belong to another BSS. 8577 * Attributes for each entry are taken from enum 8578 * qca_wlan_vendor_bss_filter_sta_stats. 8579 * Other BSS station configured in 8580 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type 8581 * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA. 8582 * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER 8583 * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET. 8584 */ 8585 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4, 8586 8587 /* keep last */ 8588 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST, 8589 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX = 8590 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1, 8591 }; 8592 8593 /** 8594 * enum qca_wlan_vendor_bss_filter_type - Type of 8595 * filter used in other BSS filter operations. Used by the vendor command 8596 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 8597 * 8598 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter 8599 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter 8600 */ 8601 enum qca_wlan_vendor_bss_filter_type { 8602 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID, 8603 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA, 8604 }; 8605 8606 /** 8607 * enum qca_wlan_vendor_bss_filter_action - Type of 8608 * action in other BSS filter operations. Used by the vendor command 8609 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 8610 * 8611 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter 8612 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter 8613 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics 8614 */ 8615 enum qca_wlan_vendor_bss_filter_action { 8616 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD, 8617 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL, 8618 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET, 8619 }; 8620 8621 /** 8622 * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for 8623 * the statistics of a specific unassociated station belonging to another BSS. 8624 * The statistics provides information of the unassociated station 8625 * filtered by other BSS operation - such as MAC, signal value. 8626 * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 8627 * 8628 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station. 8629 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength 8630 * of the station. Unsigned 8 bit number containing RSSI. 8631 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host 8632 * driver for the last received RSSI. Unsigned 64 bit number containing 8633 * nanoseconds from the boottime. 8634 */ 8635 enum qca_wlan_vendor_bss_filter_sta_stats { 8636 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0, 8637 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1, 8638 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2, 8639 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3, 8640 8641 /* keep last */ 8642 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST, 8643 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX = 8644 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1 8645 }; 8646 8647 /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute 8648 * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command 8649 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 8650 */ 8651 enum qca_wlan_nan_ext_subcmd_type { 8652 /* Subcmd of type NAN Enable Request */ 8653 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, 8654 /* Subcmd of type NAN Disable Request */ 8655 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, 8656 }; 8657 8658 /** 8659 * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command 8660 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 8661 */ 8662 enum qca_wlan_vendor_attr_nan_params { 8663 QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, 8664 /* Carries NAN command for firmware component. Every vendor command 8665 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a 8666 * payload containing the NAN command. NLA_BINARY attribute. 8667 */ 8668 QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, 8669 /* Indicates the type of NAN command sent with 8670 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type 8671 * describes the possible range of values. This attribute is mandatory 8672 * if the command being issued is either 8673 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or 8674 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. 8675 */ 8676 QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, 8677 /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz 8678 * band. This attribute is mandatory when command type is 8679 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. 8680 */ 8681 QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, 8682 /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz 8683 * band. This attribute is optional and should be included when command 8684 * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery 8685 * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. 8686 */ 8687 QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, 8688 8689 /* keep last */ 8690 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, 8691 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = 8692 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 8693 }; 8694 8695 /** 8696 * qca_wlan_twt_setup_state: Represents the TWT session states. 8697 * 8698 * QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED: TWT session not established. 8699 * QCA_WLAN_TWT_SETUP_STATE_ACTIVE: TWT session is active. 8700 * QCA_WLAN_TWT_SETUP_STATE_SUSPEND: TWT session is in suspended state. 8701 */ 8702 enum qca_wlan_twt_setup_state { 8703 QCA_WLAN_TWT_SETUP_STATE_NOT_ESTABLISHED = 0, 8704 QCA_WLAN_TWT_SETUP_STATE_ACTIVE = 1, 8705 QCA_WLAN_TWT_SETUP_STATE_SUSPEND = 2, 8706 }; 8707 8708 /** 8709 * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for 8710 * TWT (Target Wake Time) setup request. These attributes are sent as part of 8711 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and 8712 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by 8713 * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 8714 * 8715 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. 8716 * Disable (flag attribute not present) - Individual TWT 8717 * Enable (flag attribute present) - Broadcast TWT. 8718 * Individual means the session is between the STA and the AP. 8719 * This session is established using a separate negotiation between 8720 * STA and AP. 8721 * Broadcast means the session is across multiple STAs and an AP. The 8722 * configuration parameters are announced in Beacon frames by the AP. 8723 * This is used in 8724 * 1. TWT SET Request and Response 8725 * 2. TWT GET Response 8726 * 8727 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). 8728 * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to 8729 * specify the TWT request type. This is used in TWT SET operation. 8730 * 8731 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute 8732 * Enable (flag attribute present) - TWT with trigger support. 8733 * Disable (flag attribute not present) - TWT without trigger support. 8734 * Trigger means the AP will send the trigger frame to allow STA to send data. 8735 * Without trigger, the STA will wait for the MU EDCA timer before 8736 * transmitting the data. 8737 * This is used in 8738 * 1. TWT SET Request and Response 8739 * 2. TWT GET Response 8740 * 8741 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) 8742 * 0 - Announced TWT - In this mode, STA may skip few service periods to 8743 * save more power. If STA wants to wake up, it will send a PS-POLL/QoS 8744 * NULL frame to AP. 8745 * 1 - Unannounced TWT - The STA will wakeup during every SP. 8746 * This is a required parameter for 8747 * 1. TWT SET Request and Response 8748 * 2. TWT GET Response 8749 * 8750 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) 8751 * Flow ID is the unique identifier for each TWT session. 8752 * If not provided then dialog ID will be set to zero. 8753 * This is an optional parameter for 8754 * 1. TWT SET Request and Response 8755 * 2. TWT GET Request and Response 8756 * 3. TWT TERMINATE Request and Response 8757 * 4. TWT SUSPEND Request and Response 8758 * Flow ID values from 0 to 254 represent a single TWT session 8759 * Flow ID value of 255 represents all TWT sessions for the following 8760 * 1. TWT TERMINATE Request and Response 8761 * 2. TWT SUSPEND Request and Response 8762 * 4. TWT CLEAR STATISTICS request 8763 * 5. TWT GET STATISTICS request and response 8764 * If an invalid dialog ID is provided, status 8765 * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. 8766 * 8767 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) 8768 * This attribute (exp) is used along with the mantissa to derive the 8769 * wake interval using the following formula: 8770 * pow(2,exp) = wake_intvl_us/wake_intvl_mantis 8771 * Wake interval is the interval between 2 successive SP. 8772 * This is a required parameter for 8773 * 1. TWT SET Request and Response 8774 * 2. TWT GET Response 8775 * 8776 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute 8777 * Enable (flag attribute present) - Protection required. 8778 * Disable (flag attribute not present) - Protection not required. 8779 * If protection is enabled, then the AP will use protection 8780 * mechanism using RTS/CTS to self to reserve the airtime. 8781 * This is used in 8782 * 1. TWT SET Request and Response 8783 * 2. TWT GET Response 8784 * 8785 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) 8786 * This attribute is used as the SP offset which is the offset from 8787 * TSF after which the wake happens. The units are in microseconds. If 8788 * this attribute is not provided, then the value will be set to zero. 8789 * This is an optional parameter for 8790 * 1. TWT SET Request and Response 8791 * 2. TWT GET Response 8792 * 8793 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) 8794 * This is the duration of the service period. This is specified as 8795 * multiples of 256 microseconds. Valid values are 0x1 to 0xFF. 8796 * This is a required parameter for 8797 * 1. TWT SET Request and Response 8798 * 2. TWT GET Response 8799 * 8800 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) 8801 * This attribute is used to configure wake interval mantissa. 8802 * The units are in TU. 8803 * This is a required parameter for 8804 * 1. TWT SET Request and Response 8805 * 2. TWT GET Response 8806 * 8807 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS: Required (u8) 8808 * This field is applicable for TWT response only. 8809 * This contains status values in enum qca_wlan_vendor_twt_status 8810 * and is passed to the userspace. This is used in TWT SET operation. 8811 * This is a required parameter for 8812 * 1. TWT SET Response 8813 * 2. TWT TERMINATE Response 8814 * 3. TWT SUSPEND Response 8815 * 4. TWT RESUME Response 8816 * 5. TWT NUDGE Response 8817 * 8818 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE: Required (u8) 8819 * This field is applicable for TWT response only. 8820 * This field contains response type from the TWT responder and is 8821 * passed to the userspace. The values for this field are defined in 8822 * enum qca_wlan_vendor_twt_setup_resp_type. This is used in TWT SET 8823 * response. 8824 * 8825 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF: Required (u64) 8826 * In TWT setup command this field contains absolute TSF that will 8827 * be used by TWT requester during setup. 8828 * In TWT response this field contains absolute TSF value of the 8829 * wake time received from the TWT responder and is passed to 8830 * the userspace. 8831 * This is an optional parameter for 8832 * 1. TWT SET Request 8833 * This is a required parameter for 8834 * 1. TWT SET Response 8835 * 2. TWT GET Response 8836 * 8837 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED: Flag attribute. 8838 * Enable (flag attribute present) - Indicates that the TWT responder 8839 * supports reception of TWT information frame from the TWT requestor. 8840 * Disable (flag attribute not present) - Indicates that the responder 8841 * doesn't support reception of TWT information frame from requestor. 8842 * This is used in 8843 * 1. TWT SET Response 8844 * 2. TWT GET Response 8845 * 8846 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR: 6-byte MAC address 8847 * Represents the MAC address of the peer for which the TWT session 8848 * is being configured. This is used in AP mode to represent the respective 8849 * client. 8850 * In AP mode, this is a required parameter in response for 8851 * 1. TWT SET 8852 * 2. TWT GET 8853 * 3. TWT TERMINATE 8854 * 4. TWT SUSPEND 8855 * In STA mode, this is an optional parameter in request and response for 8856 * the above four TWT operations. 8857 * In AP mode, this is a required parameter in request for 8858 * 1. TWT GET 8859 * 2. TWT TERMINATE 8860 * 8861 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL: Optional (u32) 8862 * Minimum tolerance limit of wake interval parameter in microseconds. 8863 * 8864 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL: Optional (u32) 8865 * Maximum tolerance limit of wake interval parameter in microseconds. 8866 * 8867 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION: Optional (u32) 8868 * Minimum tolerance limit of wake duration parameter in microseconds. 8869 * 8870 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION: Optional (u32) 8871 * Maximum tolerance limit of wake duration parameter in microseconds. 8872 * 8873 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE: Optional (u32) 8874 * TWT state for the given dialog id. The values for this are represented 8875 * by enum qca_wlan_twt_setup_state. 8876 * This is obtained through TWT GET operation. 8877 * 8878 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA: Optional (u32) 8879 * This attribute is used to configure wake interval mantissa. 8880 * The unit is microseconds. This attribute, when specified, takes 8881 * precedence over QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA. 8882 * This parameter is used for 8883 * 1. TWT SET Request and Response 8884 * 2. TWT GET Response 8885 * 8886 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID: Optional (u8) 8887 * This attribute is used to configure Broadcast TWT ID. 8888 * The Broadcast TWT ID indicates a specific Broadcast TWT for which the 8889 * transmitting STA is providing TWT parameters. The allowed values are 0 to 31. 8890 * This parameter is used for 8891 * 1. TWT SET Request 8892 * 2. TWT TERMINATE Request 8893 * 8894 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION: Optional (u8) 8895 * This attribute is used to configure Broadcast TWT recommendation. 8896 * The Broadcast TWT Recommendation subfield contains a value that indicates 8897 * recommendations on the types of frames that are transmitted by TWT 8898 * scheduled STAs and scheduling AP during the broadcast TWT SP. 8899 * The allowed values are 0 - 3. 8900 * This parameter is used for 8901 * 1. TWT SET Request 8902 * 8903 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE: Optional (u8) 8904 * This attribute is used to configure Broadcast TWT Persistence. 8905 * The Broadcast TWT Persistence subfield indicates the number of 8906 * TBTTs during which the Broadcast TWT SPs corresponding to this 8907 * broadcast TWT Parameter set are present. The number of beacon intervals 8908 * during which the Broadcast TWT SPs are present is equal to the value in the 8909 * Broadcast TWT Persistence subfield plus 1 except that the value 255 8910 * indicates that the Broadcast TWT SPs are present until explicitly terminated. 8911 * This parameter is used for 8912 * 1. TWT SET Request 8913 * 8914 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE: Optional (u8) 8915 * This attribute contains the value of the Responder PM Mode subfield (0 or 1) 8916 * from TWT response frame. 8917 * This parameter is used for 8918 * 1. TWT SET Response 8919 * 2. TWT GET Response 8920 * 8921 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT: Optional (u32) 8922 * This attribute is used to configure the announce timeout value (in us) in 8923 * the firmware. This timeout value is only applicable for the announced TWT. If 8924 * the timeout value is non-zero the firmware waits up to the timeout value to 8925 * use Data frame as an announcement frame. If the timeout value is 0 the 8926 * firmware sends an explicit QoS NULL frame as the announcement frame on SP 8927 * start. The default value in the firmware is 0. 8928 * This parameter is used for 8929 * 1. TWT SET Request 8930 */ 8931 enum qca_wlan_vendor_attr_twt_setup { 8932 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, 8933 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, 8934 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, 8935 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, 8936 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, 8937 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, 8938 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, 8939 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, 8940 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, 8941 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, 8942 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, 8943 8944 /* TWT Response only attributes */ 8945 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATUS = 11, 8946 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESP_TYPE = 12, 8947 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME_TSF = 13, 8948 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TWT_INFO_ENABLED = 14, 8949 8950 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAC_ADDR = 15, 8951 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_INTVL = 16, 8952 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_INTVL = 17, 8953 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MIN_WAKE_DURATION = 18, 8954 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX_WAKE_DURATION = 19, 8955 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_STATE = 20, 8956 8957 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL2_MANTISSA = 21, 8958 8959 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_ID = 22, 8960 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_RECOMMENDATION = 23, 8961 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST_PERSISTENCE = 24, 8962 8963 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_RESPONDER_PM_MODE = 25, 8964 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_ANNOUNCE_TIMEOUT = 26, 8965 8966 /* keep last */ 8967 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, 8968 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = 8969 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, 8970 }; 8971 8972 /** 8973 * enum qca_wlan_vendor_twt_status - Represents the status of the requested 8974 * TWT operation 8975 * 8976 * @QCA_WLAN_VENDOR_TWT_STATUS_OK: TWT request successfully completed 8977 * @QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED: TWT not enabled 8978 * @QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID: TWT dialog ID is already used 8979 * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY: TWT session is busy 8980 * @QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST: TWT session does not exist 8981 * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED: TWT session not in suspend state 8982 * @QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM: Invalid parameters 8983 * @QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY: FW not ready 8984 * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE: FW resource exhausted 8985 * @QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK: Peer AP/STA did not ACK the 8986 * request/response frame 8987 * @QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE: Peer AP did not send the response 8988 * frame 8989 * @QCA_WLAN_VENDOR_TWT_STATUS_DENIED: AP did not accept the request 8990 * @QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR: Adding TWT dialog failed due to an 8991 * unknown reason 8992 * @QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED: TWT session already in 8993 * suspend state 8994 * @QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID: FW has dropped the frame due to 8995 * invalid IE in the received TWT frame 8996 * @QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE: Parameters received from 8997 * the responder are not in the specified range 8998 * @QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE: FW terminated the TWT 8999 * session due to request from the responder. Used on the TWT_TERMINATE 9000 * notification from the firmware. 9001 * @QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE: FW terminated the TWT 9002 * session due to roaming. Used on the TWT_TERMINATE notification from the 9003 * firmware. 9004 * @QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE: FW terminated the 9005 * TWT session due to SCC (Single Channel Concurrency) and MCC (Multi Channel 9006 * Concurrency). Used on the TWT_TERMINATE notification from the firmware. 9007 * @QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS: FW rejected the TWT setup 9008 * request due to roaming in progress. 9009 * @QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS: FW rejected the TWT 9010 * setup request due to channel switch in progress. 9011 * @QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS: FW rejected the TWT setup 9012 * request due to scan in progress. 9013 * QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE: The driver requested to 9014 * terminate an existing TWT session on power save exit request from userspace. 9015 * Used on the TWT_TERMINATE notification from the driver/firmware. 9016 */ 9017 enum qca_wlan_vendor_twt_status { 9018 QCA_WLAN_VENDOR_TWT_STATUS_OK = 0, 9019 QCA_WLAN_VENDOR_TWT_STATUS_TWT_NOT_ENABLED = 1, 9020 QCA_WLAN_VENDOR_TWT_STATUS_USED_DIALOG_ID = 2, 9021 QCA_WLAN_VENDOR_TWT_STATUS_SESSION_BUSY = 3, 9022 QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST = 4, 9023 QCA_WLAN_VENDOR_TWT_STATUS_NOT_SUSPENDED = 5, 9024 QCA_WLAN_VENDOR_TWT_STATUS_INVALID_PARAM = 6, 9025 QCA_WLAN_VENDOR_TWT_STATUS_NOT_READY = 7, 9026 QCA_WLAN_VENDOR_TWT_STATUS_NO_RESOURCE = 8, 9027 QCA_WLAN_VENDOR_TWT_STATUS_NO_ACK = 9, 9028 QCA_WLAN_VENDOR_TWT_STATUS_NO_RESPONSE = 10, 9029 QCA_WLAN_VENDOR_TWT_STATUS_DENIED = 11, 9030 QCA_WLAN_VENDOR_TWT_STATUS_UNKNOWN_ERROR = 12, 9031 QCA_WLAN_VENDOR_TWT_STATUS_ALREADY_SUSPENDED = 13, 9032 QCA_WLAN_VENDOR_TWT_STATUS_IE_INVALID = 14, 9033 QCA_WLAN_VENDOR_TWT_STATUS_PARAMS_NOT_IN_RANGE = 15, 9034 QCA_WLAN_VENDOR_TWT_STATUS_PEER_INITIATED_TERMINATE = 16, 9035 QCA_WLAN_VENDOR_TWT_STATUS_ROAM_INITIATED_TERMINATE = 17, 9036 QCA_WLAN_VENDOR_TWT_STATUS_SCC_MCC_CONCURRENCY_TERMINATE = 18, 9037 QCA_WLAN_VENDOR_TWT_STATUS_ROAMING_IN_PROGRESS = 19, 9038 QCA_WLAN_VENDOR_TWT_STATUS_CHANNEL_SWITCH_IN_PROGRESS = 20, 9039 QCA_WLAN_VENDOR_TWT_STATUS_SCAN_IN_PROGRESS = 21, 9040 QCA_WLAN_VENDOR_TWT_STATUS_POWER_SAVE_EXIT_TERMINATE = 22, 9041 }; 9042 9043 /** 9044 * enum qca_wlan_vendor_attr_twt_resume - Represents attributes for 9045 * TWT (Target Wake Time) resume request. These attributes are sent as part of 9046 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and 9047 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. Also used by 9048 * attributes through %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 9049 * 9050 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) 9051 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT: Optional (u32) 9052 * These attributes are used as the SP offset which is the offset from TSF after 9053 * which the wake happens. The units are in microseconds. Please note that 9054 * _NEXT_TWT is limited to u8 whereas _NEXT2_TWT takes the u32 data. 9055 * _NEXT2_TWT takes the precedence over _NEXT_TWT and thus the recommendation 9056 * is to use _NEXT2_TWT. If neither of these attributes is provided, the value 9057 * will be set to zero. 9058 * 9059 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) 9060 * This attribute represents the next TWT subfield size. 9061 * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, 9062 * and 4 for 64 bits. 9063 * 9064 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID: Required (u8). 9065 * Flow ID is the unique identifier for each TWT session. This attribute 9066 * represents the respective TWT session to resume. 9067 * Flow ID values from 0 to 254 represent a single TWT session 9068 * Flow ID value of 255 represents all TWT sessions. 9069 * If an invalid dialog id is provided, status 9070 * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. 9071 * 9072 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR: 6-byte MAC address 9073 * Represents the MAC address of the peer to which TWT Resume is 9074 * being sent. This is used in AP mode to represent the respective 9075 * client and is a required parameter. In STA mode, this is an optional 9076 * parameter 9077 */ 9078 enum qca_wlan_vendor_attr_twt_resume { 9079 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, 9080 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, 9081 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, 9082 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_FLOW_ID = 3, 9083 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT2_TWT = 4, 9084 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAC_ADDR = 5, 9085 9086 /* keep last */ 9087 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, 9088 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = 9089 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, 9090 }; 9091 9092 /** 9093 * enum qca_wlan_vendor_attr_twt_nudge - Represents attributes for 9094 * TWT (Target Wake Time) nudge request. TWT nudge is a combination of suspend 9095 * and resume in a single request. These attributes are sent as part of 9096 * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 9097 * 9098 * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID: Required (u8) 9099 * Flow ID is the unique identifier for each TWT session. This attribute 9100 * represents the respective TWT session to suspend and resume. 9101 * Flow ID values from 0 to 254 represent a single TWT session 9102 * Flow ID value of 255 represents all TWT sessions in TWT NUDGE request 9103 * and response. 9104 * If an invalid dialog id is provided, status 9105 * QCA_WLAN_VENDOR_TWT_STATUS_SESSION_NOT_EXIST will be returned. 9106 * 9107 * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME: Required (u32) 9108 * This attribute is used as the SP offset which is the offset from 9109 * TSF after which the wake happens. The units are in microseconds. 9110 * 9111 * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE: Required (u32) 9112 * This attribute represents the next TWT subfield size. 9113 * Value 0 represents 0 bits, 1 represents 32 bits, 2 for 48 bits, 9114 * and 4 for 64 bits. 9115 * 9116 * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR: 6-byte MAC address 9117 * Represents the MAC address of the peer to which TWT Suspend and Resume is 9118 * being sent. This is used in AP mode to represent the respective 9119 * client and is a required parameter. In STA mode, this is an optional 9120 * parameter. 9121 * 9122 * @QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF: Optional (u64) 9123 * This field contains absolute TSF value of the time at which the TWT 9124 * session will be resumed. 9125 */ 9126 enum qca_wlan_vendor_attr_twt_nudge { 9127 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_INVALID = 0, 9128 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_FLOW_ID = 1, 9129 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME = 2, 9130 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_NEXT_TWT_SIZE = 3, 9131 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAC_ADDR = 4, 9132 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_WAKE_TIME_TSF = 5, 9133 9134 /* keep last */ 9135 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST, 9136 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_MAX = 9137 QCA_WLAN_VENDOR_ATTR_TWT_NUDGE_AFTER_LAST - 1, 9138 }; 9139 9140 /** 9141 * enum qca_wlan_vendor_attr_twt_stats: Represents attributes for 9142 * TWT (Target Wake Time) get statistics and clear statistics request. 9143 * These attributes are sent as part of 9144 * %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 9145 * 9146 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID: Required (u8) 9147 * Flow ID is the unique identifier for each TWT session. This attribute 9148 * represents the respective TWT session for get and clear TWT statistics. 9149 * Flow ID values from 0 to 254 represent a single TWT session 9150 * Flow ID value of 255 represents all TWT sessions in 9151 * 1) TWT GET STATISTICS request and response 9152 * 2) TWT CLEAR STATISTICS request 9153 * 9154 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR: 6-byte MAC address 9155 * Represents the MAC address of the peer for which TWT Statistics 9156 * is required. 9157 * In AP mode this is used to represent the respective 9158 * client and is a required parameter for 9159 * 1) TWT GET STATISTICS request and response 9160 * 2) TWT CLEAR STATISTICS request and response 9161 * In STA mode, this is an optional parameter. 9162 * 9163 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION: Required (u32) 9164 * This is the duration of the service period in microseconds. 9165 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9166 * 9167 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION: Required (u32) 9168 * Average of the actual wake duration observed so far. Unit is microseconds. 9169 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9170 * 9171 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS: Required (u32) 9172 * The number of TWT service periods elapsed so far. 9173 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9174 * 9175 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION: Required (u32) 9176 * This is the minimum value of the wake duration observed across 9177 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is 9178 * microseconds. 9179 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9180 * 9181 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX_WAKE_DURATION: Required (u32) 9182 * This is the maximum value of wake duration observed across 9183 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. Unit is 9184 * microseconds. 9185 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9186 * 9187 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU: Required (u32) 9188 * Average number of MPDUs transmitted successfully across 9189 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. 9190 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9191 * 9192 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU: Required (u32) 9193 * Average number of MPDUs received successfully across 9194 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. 9195 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9196 * 9197 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE: Required (u32) 9198 * Average number of bytes transmitted successfully across 9199 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. 9200 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9201 * 9202 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET_SIZE: Required (u32) 9203 * Average number of bytes received successfully across 9204 * QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS. 9205 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9206 * 9207 * @QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS: Required (u32) 9208 * Status of the TWT GET STATISTICS request. 9209 * This contains status values in enum qca_wlan_vendor_twt_status 9210 * Obtained in the QCA_WLAN_TWT_GET_STATS response from the firmware. 9211 */ 9212 enum qca_wlan_vendor_attr_twt_stats { 9213 QCA_WLAN_VENDOR_ATTR_TWT_STATS_INVALID = 0, 9214 QCA_WLAN_VENDOR_ATTR_TWT_STATS_FLOW_ID = 1, 9215 QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAC_ADDR = 2, 9216 QCA_WLAN_VENDOR_ATTR_TWT_STATS_SESSION_WAKE_DURATION = 3, 9217 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVG_WAKE_DURATION = 4, 9218 QCA_WLAN_VENDOR_ATTR_TWT_STATS_NUM_SP_ITERATIONS = 5, 9219 QCA_WLAN_VENDOR_ATTR_TWT_STATS_MIN_WAKE_DURATION = 6, 9220 QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX_WAKE_DURATION = 7, 9221 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_MPDU = 8, 9222 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_MPDU = 9, 9223 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_TX_PACKET_SIZE = 10, 9224 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AVERAGE_RX_PACKET_SIZE = 11, 9225 QCA_WLAN_VENDOR_ATTR_TWT_STATS_STATUS = 12, 9226 9227 /* keep last */ 9228 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST, 9229 QCA_WLAN_VENDOR_ATTR_TWT_STATS_MAX = 9230 QCA_WLAN_VENDOR_ATTR_TWT_STATS_AFTER_LAST - 1, 9231 }; 9232 9233 /** 9234 * qca_wlan_twt_get_capa - Represents the bitmap of TWT capabilities 9235 * supported by the device and the peer. 9236 * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_GET_CAPABILITIES 9237 * 9238 * @QCA_WLAN_TWT_CAPA_REQUESTOR: TWT requestor support is advertised by 9239 * TWT non-scheduling STA. This capability is advertised in the HE 9240 * Capability/Extended Capabilities information element in the 9241 * Association Request frame by the device. 9242 * 9243 * @QCA_WLAN_TWT_CAPA_RESPONDER: TWT responder support is advertised by 9244 * the TWT scheduling AP. This capability is advertised in the Extended 9245 * Capabilities/HE Capabilities information element. 9246 * 9247 * @QCA_WLAN_TWT_CAPA_BROADCAST: On the requestor side, this indicates support 9248 * for the broadcast TWT functionality. On the responder side, this indicates 9249 * support for the role of broadcast TWT scheduling functionality. This 9250 * capability is advertised in the HE Capabilities information element. 9251 * 9252 * @QCA_WLAN_TWT_CAPA_TWT_FLEXIBLE: The device supports flexible TWT schedule. 9253 * This capability is advertised in the HE Capabilities information element. 9254 * 9255 * @QCA_WLAN_TWT_CAPA_REQUIRED: The TWT Required is advertised by AP to indicate 9256 * that it mandates the associated HE STAs to support TWT. This capability is 9257 * advertised by AP in the HE Operation Parameters field of the HE Operation 9258 * information element. 9259 */ 9260 enum qca_wlan_twt_capa { 9261 QCA_WLAN_TWT_CAPA_REQUESTOR = BIT(0), 9262 QCA_WLAN_TWT_CAPA_RESPONDER = BIT(1), 9263 QCA_WLAN_TWT_CAPA_BROADCAST = BIT(2), 9264 QCA_WLAN_TWT_CAPA_FLEXIBLE = BIT(3), 9265 QCA_WLAN_TWT_CAPA_REQUIRED = BIT(4), 9266 }; 9267 9268 /** 9269 * enum qca_wlan_vendor_attr_twt_capability - Represents attributes for TWT 9270 * get capabilities request type. Used by QCA_WLAN_TWT_GET_CAPABILITIES TWT 9271 * operation. 9272 * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR: 6-byte MAC address 9273 * Represents the MAC address of the peer for which the TWT capabilities 9274 * are being queried. This is used in AP mode to represent the respective 9275 * client. In STA mode, this is an optional parameter. 9276 * 9277 * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF: (u16). 9278 * Self TWT capabilities. Carries a bitmap of TWT capabilities specified in 9279 * enum qca_wlan_twt_capa. 9280 * @QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER: (u16). 9281 * Peer TWT capabilities. Carries a bitmap of TWT capabilities specified in 9282 * enum qca_wlan_twt_capa. 9283 */ 9284 enum qca_wlan_vendor_attr_twt_capability { 9285 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_INVALID = 0, 9286 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAC_ADDR = 1, 9287 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_SELF = 2, 9288 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_PEER = 3, 9289 9290 /* keep last */ 9291 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST, 9292 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_MAX = 9293 QCA_WLAN_VENDOR_ATTR_TWT_CAPABILITIES_AFTER_LAST - 1, 9294 }; 9295 9296 /** 9297 * enum qca_wlan_vendor_attr_twt_set_param: Represents attributes for 9298 * TWT (Target Wake Time) related parameters. It is used when 9299 * %QCA_WLAN_VENDOR_ATTR_CONFIG_TWT_OPERATION is set to %QCA_WLAN_TWT_SET_PARAM. 9300 * These attributes are sent as part of %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TWT. 9301 * 9302 * @QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE: Optional (u8) 9303 * This attribute configures AC parameters to be used for all TWT 9304 * sessions in AP mode. 9305 * Uses the enum qca_wlan_ac_type values. 9306 */ 9307 enum qca_wlan_vendor_attr_twt_set_param { 9308 QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_INVALID = 0, 9309 QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AP_AC_VALUE = 1, 9310 9311 /* keep last */ 9312 QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST, 9313 QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_MAX = 9314 QCA_WLAN_VENDOR_ATTR_TWT_SET_PARAM_AFTER_LAST - 1, 9315 }; 9316 9317 /** 9318 * enum qca_wlan_vendor_twt_setup_resp_type - Represents the response type by 9319 * the TWT responder 9320 * 9321 * @QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE: TWT responder suggests TWT 9322 * parameters that are different from TWT requesting STA suggested 9323 * or demanded TWT parameters 9324 * @QCA_WLAN_VENDOR_TWT_RESP_DICTATE: TWT responder demands TWT 9325 * parameters that are different from TWT requesting STA TWT suggested 9326 * or demanded parameters 9327 * @QCA_WLAN_VENDOR_TWT_RESP_REJECT: TWT responder rejects TWT 9328 * setup 9329 * @QCA_WLAN_VENDOR_TWT_RESP_ACCEPT: TWT responder accepts the TWT 9330 * setup. 9331 */ 9332 enum qca_wlan_vendor_twt_setup_resp_type { 9333 QCA_WLAN_VENDOR_TWT_RESP_ALTERNATE = 1, 9334 QCA_WLAN_VENDOR_TWT_RESP_DICTATE = 2, 9335 QCA_WLAN_VENDOR_TWT_RESP_REJECT = 3, 9336 QCA_WLAN_VENDOR_TWT_RESP_ACCEPT = 4, 9337 }; 9338 9339 /** 9340 * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) 9341 * Represents the setup type being requested for TWT. 9342 * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT 9343 * parameters but relying on AP to fill the parameters during the negotiation. 9344 * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested 9345 * values which the AP may accept or AP may provide alternative parameters 9346 * which the STA may accept. 9347 * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any 9348 * alternate parameters than the requested ones. 9349 */ 9350 enum qca_wlan_vendor_twt_setup_req_type { 9351 QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, 9352 QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, 9353 QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, 9354 }; 9355 9356 /** 9357 * enum qca_wlan_roam_scan_event_type - Type of roam scan event 9358 * 9359 * Indicates the type of roam scan event sent by firmware/driver. 9360 * 9361 * @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type. 9362 * @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type. 9363 */ 9364 enum qca_wlan_roam_scan_event_type { 9365 QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT = 0, 9366 QCA_WLAN_ROAM_SCAN_STOP_EVENT = 1, 9367 }; 9368 9369 /** 9370 * enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason 9371 * 9372 * Indicates the reason for triggering roam scan by firmware/driver. 9373 * 9374 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP. 9375 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate. 9376 */ 9377 enum qca_wlan_roam_scan_trigger_reason { 9378 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI = 0, 9379 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER = 1, 9380 }; 9381 9382 /** 9383 * enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report 9384 * roam scan related details from driver/firmware to user space. enum values 9385 * are used for NL attributes sent with 9386 * %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command. 9387 */ 9388 enum qca_wlan_vendor_attr_roam_scan { 9389 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID = 0, 9390 /* Encapsulates type of roam scan event being reported. enum 9391 * qca_wlan_roam_scan_event_type describes the possible range of 9392 * values. u32 attribute. 9393 */ 9394 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE = 1, 9395 /* Encapsulates reason for triggering roam scan. enum 9396 * qca_wlan_roam_scan_trigger_reason describes the possible range of 9397 * values. u32 attribute. 9398 */ 9399 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON = 2, 9400 9401 /* keep last */ 9402 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST, 9403 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX = 9404 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST - 1, 9405 }; 9406 9407 /** 9408 * enum qca_wlan_vendor_cfr_data_transport_modes - Defines QCA vendor CFR data 9409 * transport modes and is used by the attribute 9410 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE as a part of the vendor 9411 * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. 9412 * @QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS: Use relayfs to send CFR data. 9413 * @QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS: Use netlink events to send CFR 9414 * data. The data shall be encapsulated within 9415 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA along with the vendor sub command 9416 * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an asynchronous event. 9417 */ 9418 enum qca_wlan_vendor_cfr_data_transport_modes { 9419 QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS = 0, 9420 QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS = 1, 9421 }; 9422 9423 /** 9424 * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by 9425 * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor 9426 * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. 9427 * @QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL: CFR method using QoS Null frame 9428 * @QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE: CFR method using QoS Null frame 9429 * with phase 9430 * @QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE: CFR method using Probe Response frame 9431 */ 9432 enum qca_wlan_vendor_cfr_method { 9433 QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0, 9434 QCA_WLAN_VENDOR_CFR_QOS_NULL_WITH_PHASE = 1, 9435 QCA_WLAN_VENDOR_CFR_PROBE_RESPONSE = 2, 9436 }; 9437 9438 /** 9439 * enum qca_wlan_vendor_cfr_capture_type - QCA vendor CFR capture type used by 9440 * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE. 9441 * @QCA_WLAN_VENDOR_CFR_DIRECT_FTM: Filter directed FTM ACK frames. 9442 * @QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK: Filter all FTM ACK frames. 9443 * @QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP: Filter NDPA NDP directed frames. 9444 * @QCA_WLAN_VENDOR_CFR_TA_RA: Filter frames based on TA/RA/Subtype which 9445 * is provided by one or more of below attributes: 9446 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA 9447 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA 9448 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK 9449 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK 9450 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER 9451 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER 9452 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER 9453 * @QCA_WLAN_CFR_ALL_PACKET: Filter all packets. 9454 * @QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL: Filter all NDPA NDP frames. 9455 */ 9456 enum qca_wlan_vendor_cfr_capture_type { 9457 QCA_WLAN_VENDOR_CFR_DIRECT_FTM = 0, 9458 QCA_WLAN_VENDOR_CFR_ALL_FTM_ACK = 1, 9459 QCA_WLAN_VENDOR_CFR_DIRECT_NDPA_NDP = 2, 9460 QCA_WLAN_VENDOR_CFR_TA_RA = 3, 9461 QCA_WLAN_VENDOR_CFR_ALL_PACKET = 4, 9462 QCA_WLAN_VENDOR_CFR_NDPA_NDP_ALL = 5, 9463 }; 9464 9465 /** 9466 * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command 9467 * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer 9468 * Channel Frequency Response capture parameters and enable periodic CFR 9469 * capture. 9470 * 9471 * @QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR: Optional (6-byte MAC address) 9472 * MAC address of peer. This is for CFR version 1 only. 9473 * 9474 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE: Required (flag) 9475 * Enable peer CFR capture. This attribute is mandatory to enable peer CFR 9476 * capture. If this attribute is not present, peer CFR capture is disabled. 9477 * 9478 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH: Optional (u8) 9479 * BW of measurement, attribute uses the values in enum nl80211_chan_width 9480 * Supported values: 20, 40, 80, 80+80, 160. 9481 * Note that all targets may not support all bandwidths. 9482 * This attribute is mandatory for version 1 if attribute 9483 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 9484 * 9485 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY: Optional (u32) 9486 * Periodicity of CFR measurement in milliseconds. 9487 * Periodicity should be a multiple of Base timer. 9488 * Current Base timer value supported is 10 milliseconds (default). 9489 * 0 for one shot capture. 9490 * This attribute is mandatory for version 1 if attribute 9491 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 9492 * 9493 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD: Optional (u8) 9494 * Method used to capture Channel Frequency Response. 9495 * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method. 9496 * This attribute is mandatory for version 1 if attribute 9497 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 9498 * 9499 * @QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE: Optional (flag) 9500 * Enable periodic CFR capture. 9501 * This attribute is mandatory for version 1 to enable Periodic CFR capture. 9502 * If this attribute is not present, periodic CFR capture is disabled. 9503 * 9504 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION: Optional (u8) 9505 * Value is 1 or 2 since there are two versions of CFR capture. Two versions 9506 * can't be enabled at same time. This attribute is mandatory if target 9507 * support both versions and use one of them. 9508 * 9509 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP: Optional (u32) 9510 * This attribute is mandatory for version 2 if 9511 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY is used. 9512 * Bits 15:0 bitfield indicates which group is to be enabled. 9513 * Bits 31:16 Reserved for future use. 9514 * 9515 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION: Optional (u32) 9516 * CFR capture duration in microsecond. This attribute is mandatory for 9517 * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL is used. 9518 * 9519 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL: Optional (u32) 9520 * CFR capture interval in microsecond. This attribute is mandatory for 9521 * version 2 if attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION is used. 9522 * 9523 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE: Optional (u32) 9524 * CFR capture type is defined in enum qca_wlan_vendor_cfr_capture_type. 9525 * This attribute is mandatory for version 2. 9526 * 9527 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK: Optional (u64) 9528 * Bitfield indicating which user in the current UL MU transmissions are 9529 * enabled for CFR capture. Bits 36 to 0 indicate user indexes for 37 users in 9530 * a UL MU transmission. If bit 0 is set, the CFR capture will happen for user 9531 * index 0 in the current UL MU transmission. If bits 0 and 2 are set, CFR 9532 * capture for UL MU TX corresponds to user indices 0 and 2. Bits 63:37 are 9533 * reserved for future use. This is for CFR version 2 only. 9534 * 9535 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT: Optional (u32) 9536 * Indicates the number of consecutive RX frames to be skipped before CFR 9537 * capture is enabled again. This is for CFR version 2 only. 9538 * 9539 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE: Nested attribute containing 9540 * one or more %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY attributes. 9541 * 9542 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY: Nested attribute containing 9543 * the following group attributes: 9544 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER, 9545 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA, 9546 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA, 9547 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK, 9548 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK, 9549 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS, 9550 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW, 9551 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER, 9552 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER, 9553 * %QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER 9554 * 9555 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER: Optional (u32) 9556 * Target supports multiple groups for some configurations. The group number 9557 * can be any value between 0 and 15. This is for CFR version 2 only. 9558 * 9559 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA: Optional (6-byte MAC address) 9560 * Transmitter address which is used to filter frames. This MAC address takes 9561 * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK. This is for CFR 9562 * version 2 only. 9563 * 9564 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA: Optional (6-byte MAC address) 9565 * Receiver address which is used to filter frames. This MAC address takes 9566 * effect with QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK. This is for CFR 9567 * version 2 only. 9568 * 9569 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK: Optional (6-byte MAC address) 9570 * Mask of transmitter address which is used to filter frames. This is for CFR 9571 * version 2 only. 9572 * 9573 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK: Optional (6-byte MAC address) 9574 * Mask of receiver address which is used to filter frames. This is for CFR 9575 * version 2 only. 9576 * 9577 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS: Optional (u32) 9578 * Indicates frames with a specific NSS will be filtered for CFR capture. 9579 * This is for CFR version 2 only. This is a bitmask. Bits 7:0 request CFR 9580 * capture to be done for frames matching the NSS specified within this bitmask. 9581 * Bits 31:8 are reserved for future use. Bits 7:0 map to NSS: 9582 * bit 0 : NSS 1 9583 * bit 1 : NSS 2 9584 * ... 9585 * bit 7 : NSS 8 9586 * 9587 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW: Optional (u32) 9588 * Indicates frames with a specific bandwidth will be filtered for CFR capture. 9589 * This is for CFR version 2 only. This is a bitmask. Bits 4:0 request CFR 9590 * capture to be done for frames matching the bandwidths specified within this 9591 * bitmask. Bits 31:5 are reserved for future use. Bits 4:0 map to bandwidth 9592 * numerated in enum nl80211_band (although not all bands may be supported 9593 * by a given device). 9594 * 9595 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER: Optional (u32) 9596 * Management frames matching the subtype filter categories will be filtered in 9597 * by MAC for CFR capture. This is a bitmask in which each bit represents the 9598 * corresponding Management frame subtype value per IEEE Std 802.11-2016, 9599 * 9.2.4.1.3 Type and Subtype subfields. For example, Beacon frame control type 9600 * is 8 and its value is 1 << 8 = 0x100. This is for CFR version 2 only. 9601 * 9602 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER: Optional (u32) 9603 * Control frames matching the subtype filter categories will be filtered in by 9604 * MAC for CFR capture. This is a bitmask in which each bit represents the 9605 * corresponding Control frame subtype value per IEEE Std 802.11-2016, 9606 * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only. 9607 * 9608 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER: Optional (u32) 9609 * Data frames matching the subtype filter categories will be filtered in by 9610 * MAC for CFR capture. This is a bitmask in which each bit represents the 9611 * corresponding Data frame subtype value per IEEE Std 802.11-2016, 9612 * 9.2.4.1.3 Type and Subtype subfields. This is for CFR version 2 only. 9613 * 9614 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE: Optional (u8) 9615 * Userspace can use this attribute to specify the driver about which transport 9616 * mode shall be used by the driver to send CFR data to userspace. Uses values 9617 * from enum qca_wlan_vendor_cfr_data_transport_modes. When this attribute is 9618 * not present, the driver shall use the default transport mechanism which is 9619 * QCA_WLAN_VENDOR_CFR_DATA_RELAY_FS. 9620 * 9621 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID: Optional (u32) 9622 * Userspace can use this attribute to specify the nl port id of the application 9623 * which receives the CFR data and processes it further so that the drivers can 9624 * unicast the netlink events to a specific application. Optionally included 9625 * when QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE is set to 9626 * QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS, not required otherwise. The drivers 9627 * shall multicast the netlink events when this attribute is not included. 9628 * 9629 * @QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA: Required (NLA_BINARY). 9630 * This attribute will be used by the driver to encapsulate and send CFR data 9631 * to userspace along with QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG as an 9632 * asynchronous event when the driver is configured to send CFR data using 9633 * netlink events with %QCA_WLAN_VENDOR_CFR_DATA_NETLINK_EVENTS. 9634 */ 9635 enum qca_wlan_vendor_peer_cfr_capture_attr { 9636 QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0, 9637 QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1, 9638 QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2, 9639 QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3, 9640 QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4, 9641 QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5, 9642 QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6, 9643 QCA_WLAN_VENDOR_ATTR_PEER_CFR_VERSION = 7, 9644 QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE_GROUP_BITMAP = 8, 9645 QCA_WLAN_VENDOR_ATTR_PEER_CFR_DURATION = 9, 9646 QCA_WLAN_VENDOR_ATTR_PEER_CFR_INTERVAL = 10, 9647 QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_TYPE = 11, 9648 QCA_WLAN_VENDOR_ATTR_PEER_CFR_UL_MU_MASK = 12, 9649 QCA_WLAN_VENDOR_ATTR_PEER_CFR_FREEZE_TLV_DELAY_COUNT = 13, 9650 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TABLE = 14, 9651 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_ENTRY = 15, 9652 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NUMBER = 16, 9653 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA = 17, 9654 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA = 18, 9655 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_TA_MASK = 19, 9656 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_RA_MASK = 20, 9657 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_NSS = 21, 9658 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_BW = 22, 9659 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_MGMT_FILTER = 23, 9660 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_CTRL_FILTER = 24, 9661 QCA_WLAN_VENDOR_ATTR_PEER_CFR_GROUP_DATA_FILTER = 25, 9662 QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_TRANSPORT_MODE = 26, 9663 QCA_WLAN_VENDOR_ATTR_PEER_CFR_DATA_RECEIVER_PID = 27, 9664 QCA_WLAN_VENDOR_ATTR_PEER_CFR_RESP_DATA = 28, 9665 9666 /* Keep last */ 9667 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST, 9668 QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX = 9669 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1, 9670 }; 9671 9672 /** 9673 * enum qca_wlan_throughput_level - Current throughput level 9674 * 9675 * Indicates the current level of throughput calculated by the driver. The 9676 * driver may choose different thresholds to decide whether the throughput level 9677 * is low or medium or high based on variety of parameters like physical link 9678 * capacity of the current connection, the number of packets being dispatched 9679 * per second, etc. The throughput level events might not be consistent with the 9680 * actual current throughput value being observed. 9681 * 9682 * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput 9683 * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput 9684 * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput 9685 */ 9686 enum qca_wlan_throughput_level { 9687 QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, 9688 QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, 9689 QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, 9690 }; 9691 9692 /** 9693 * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to 9694 * report throughput changes from the driver to user space. enum values are used 9695 * for netlink attributes sent with 9696 * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. 9697 */ 9698 enum qca_wlan_vendor_attr_throughput_change { 9699 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, 9700 /* Indicates the direction of throughput in which the change is being 9701 * reported. u8 attribute. Value is 0 for TX and 1 for RX. 9702 */ 9703 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, 9704 /* Indicates the newly observed throughput level. enum 9705 * qca_wlan_throughput_level describes the possible range of values. 9706 * u8 attribute. 9707 */ 9708 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, 9709 /* Indicates the driver's guidance on the new value to be set to 9710 * kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The 9711 * driver may optionally include this attribute. 9712 */ 9713 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, 9714 /* Indicates the driver's guidance on the new value to be set to 9715 * kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible 9716 * values are from -31 to 31. The driver may optionally include this 9717 * attribute. 9718 */ 9719 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, 9720 /* Indicates the driver's guidance on the new value to be set to 9721 * kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may 9722 * optionally include this attribute. 9723 */ 9724 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, 9725 9726 /* keep last */ 9727 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, 9728 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = 9729 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, 9730 }; 9731 9732 /** 9733 * enum qca_coex_config_profiles - This enum defines different types of 9734 * traffic streams that can be prioritized one over the other during coex 9735 * scenarios. 9736 * The types defined in this enum are categorized in the below manner. 9737 * 0 - 31 values corresponds to WLAN 9738 * 32 - 63 values corresponds to BT 9739 * 64 - 95 values corresponds to Zigbee 9740 * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA 9741 * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA 9742 * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA 9743 * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA 9744 * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA 9745 * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP 9746 * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP 9747 * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP 9748 * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP 9749 * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP 9750 * @QCA_BT_A2DP: Prioritize BT A2DP 9751 * @QCA_BT_BLE: Prioritize BT BLE 9752 * @QCA_BT_SCO: Prioritize BT SCO 9753 * @QCA_ZB_LOW: Prioritize Zigbee Low 9754 * @QCA_ZB_HIGH: Prioritize Zigbee High 9755 */ 9756 enum qca_coex_config_profiles { 9757 /* 0 - 31 corresponds to WLAN */ 9758 QCA_WIFI_STA_DISCOVERY = 0, 9759 QCA_WIFI_STA_CONNECTION = 1, 9760 QCA_WIFI_STA_CLASS_3_MGMT = 2, 9761 QCA_WIFI_STA_DATA = 3, 9762 QCA_WIFI_STA_ALL = 4, 9763 QCA_WIFI_SAP_DISCOVERY = 5, 9764 QCA_WIFI_SAP_CONNECTION = 6, 9765 QCA_WIFI_SAP_CLASS_3_MGMT = 7, 9766 QCA_WIFI_SAP_DATA = 8, 9767 QCA_WIFI_SAP_ALL = 9, 9768 QCA_WIFI_CASE_MAX = 31, 9769 /* 32 - 63 corresponds to BT */ 9770 QCA_BT_A2DP = 32, 9771 QCA_BT_BLE = 33, 9772 QCA_BT_SCO = 34, 9773 QCA_BT_CASE_MAX = 63, 9774 /* 64 - 95 corresponds to Zigbee */ 9775 QCA_ZB_LOW = 64, 9776 QCA_ZB_HIGH = 65, 9777 QCA_ZB_CASE_MAX = 95, 9778 /* 0xff is default value if the u8 profile value is not set. */ 9779 QCA_COEX_CONFIG_PROFILE_DEFAULT_VALUE = 255 9780 }; 9781 9782 /** 9783 * enum qca_vendor_attr_coex_config_types - Coex configurations types. 9784 * This enum defines the valid set of values of coex configuration types. These 9785 * values may used by attribute 9786 * %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE. 9787 * 9788 * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the 9789 * weights to default values. 9790 * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config 9791 * weights with configurability value. 9792 */ 9793 enum qca_vendor_attr_coex_config_types { 9794 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, 9795 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1, 9796 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2, 9797 }; 9798 9799 /** 9800 * enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes 9801 * 9802 * @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable 9803 * length array of 8-bit values from enum qca_coex_config_profiles. 9804 * FW will prioritize the profiles in the order given in the array encapsulated 9805 * in this attribute. 9806 * For example: 9807 * ----------------------------------------------------------------------- 9808 * | 1 | 34 | 32 | 65 | 9809 * ----------------------------------------------------------------------- 9810 * If the attribute contains the values defined in above array then it means 9811 * 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH. 9812 * 2) BT_SCO has priority over BT_A2DP. 9813 * 3) BT_A2DP has priority over ZIGBEE HIGH. 9814 * Profiles which are not listed in this array shall not be preferred over the 9815 * profiles which are listed in the array as a part of this attribute. 9816 */ 9817 enum qca_vendor_attr_coex_config { 9818 QCA_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, 9819 QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES = 1, 9820 9821 /* Keep last */ 9822 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST, 9823 QCA_VENDOR_ATTR_COEX_CONFIG_MAX = 9824 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST - 1, 9825 }; 9826 9827 /** 9828 * enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config 9829 * attributes 9830 * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG 9831 * 9832 * QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute. 9833 * Indicate config type. 9834 * The config types are 32-bit values from qca_vendor_attr_coex_config_types 9835 * 9836 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute. 9837 * Indicate the Priority 1 profiles. 9838 * The profiles are 8-bit values from enum qca_coex_config_profiles. 9839 * In same priority level, maximum to 4 profiles can be set here. 9840 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute. 9841 * Indicate the Priority 2 profiles. 9842 * The profiles are 8-bit values from enum qca_coex_config_profiles. 9843 * In same priority level, maximum to 4 profiles can be set here. 9844 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute. 9845 * Indicate the Priority 3 profiles. 9846 * The profiles are 8-bit values from enum qca_coex_config_profiles. 9847 * In same priority level, maximum to 4 profiles can be set here. 9848 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute. 9849 * Indicate the Priority 4 profiles. 9850 * The profiles are 8-bit values from enum qca_coex_config_profiles. 9851 * In same priority level, maximum to 4 profiles can be set here. 9852 * NOTE: 9853 * Limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority 9854 * arrangement: 9855 * 1: In the same u32 attribute (priority x), the profiles enum values own 9856 * same priority level. 9857 * 2: 0xff is default value if the u8 profile value is not set. 9858 * 3: max to 4 rules/profiles in same priority level. 9859 * 4: max to 4 priority level (priority 1 - priority 4) 9860 * 5: one priority level only supports one scenario from WLAN/BT/ZB, 9861 * hybrid rules not support. 9862 * 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will 9863 * remain blank to reset all parameters. 9864 * For example: 9865 * 9866 * If the attributes as follow: 9867 * priority 1: 9868 * ------------------------------------ 9869 * | 0xff | 0 | 1 | 2 | 9870 * ------------------------------------ 9871 * priority 2: 9872 * ------------------------------------- 9873 * | 0xff | 0xff | 0xff | 32 | 9874 * ------------------------------------- 9875 * priority 3: 9876 * ------------------------------------- 9877 * | 0xff | 0xff | 0xff | 65 | 9878 * ------------------------------------- 9879 * then it means: 9880 * 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION 9881 * owns same priority level. 9882 * 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION 9883 * has priority over BT_A2DP and ZB_HIGH. 9884 * 3: BT_A2DP has priority over ZB_HIGH. 9885 */ 9886 9887 enum qca_vendor_attr_coex_config_three_way { 9888 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0, 9889 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1, 9890 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2, 9891 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3, 9892 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4, 9893 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5, 9894 9895 /* Keep last */ 9896 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST, 9897 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX = 9898 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1, 9899 }; 9900 9901 /** 9902 * enum qca_wlan_vendor_attr_link_properties - Represent the link properties. 9903 * 9904 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer 9905 * (STA/AP) for the connected link. 9906 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a 9907 * &struct nl80211_sta_flag_update for the respective connected link. MAC 9908 * address of the peer represented by 9909 * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. 9910 */ 9911 enum qca_wlan_vendor_attr_link_properties { 9912 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, 9913 /* 1 - 3 are reserved */ 9914 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, 9915 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, 9916 9917 /* Keep last */ 9918 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, 9919 QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX = 9920 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, 9921 }; 9922 9923 /** 9924 * enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type 9925 * This enum defines the valid set of values of peer stats cache types. These 9926 * values are used by attribute 9927 * %QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE. 9928 * 9929 * @QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS: Represents peer TX rate statistics 9930 * @QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS: Represents peer RX rate statistics 9931 * @QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS: Represents peer TX sojourn 9932 * statistics 9933 */ 9934 enum qca_vendor_attr_peer_stats_cache_type { 9935 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID = 0, 9936 9937 QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS, 9938 QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS, 9939 QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS, 9940 }; 9941 9942 /** 9943 * enum qca_wlan_vendor_attr_peer_stats_cache_params - This enum defines 9944 * attributes required for QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH 9945 * Information in these attributes is used to flush peer rate statistics from 9946 * the driver to user application. 9947 * 9948 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE: Unsigned 32-bit attribute 9949 * Indicate peer statistics cache type. 9950 * The statistics types are 32-bit values from 9951 * enum qca_vendor_attr_peer_stats_cache_type. 9952 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC: Unsigned 8-bit array 9953 * of size 6 octets, representing the peer MAC address. 9954 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA: Opaque data attribute 9955 * containing buffer of statistics to send to application layer entity. 9956 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE: Unsigned 64-bit attribute 9957 * representing a cookie for peer unique session. 9958 */ 9959 enum qca_wlan_vendor_attr_peer_stats_cache_params { 9960 QCA_WLAN_VENDOR_ATTR_PEER_STATS_INVALID = 0, 9961 9962 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE = 1, 9963 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC = 2, 9964 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA = 3, 9965 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE = 4, 9966 9967 /* Keep last */ 9968 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST, 9969 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_MAX = 9970 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST - 1 9971 }; 9972 9973 /** 9974 * enum qca_mpta_helper_attr_zigbee_state - Current Zigbee state 9975 * This enum defines all the possible states of Zigbee, which can be 9976 * delivered in the QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE attribute. 9977 * 9978 * @ZIGBEE_IDLE: Zigbee in idle state 9979 * @ZIGBEE_FORM_NETWORK: Zigbee forming network 9980 * @ZIGBEE_WAIT_JOIN: Zigbee waiting for joining network 9981 * @ZIGBEE_JOIN: Zigbee joining network 9982 * @ZIGBEE_NETWORK_UP: Zigbee network is up 9983 * @ZIGBEE_HMI: Zigbee in HMI mode 9984 */ 9985 enum qca_mpta_helper_attr_zigbee_state { 9986 ZIGBEE_IDLE = 0, 9987 ZIGBEE_FORM_NETWORK = 1, 9988 ZIGBEE_WAIT_JOIN = 2, 9989 ZIGBEE_JOIN = 3, 9990 ZIGBEE_NETWORK_UP = 4, 9991 ZIGBEE_HMI = 5, 9992 }; 9993 9994 /* 9995 * enum qca_mpta_helper_vendor_attr - Attributes used in vendor sub-command 9996 * QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG. 9997 */ 9998 enum qca_mpta_helper_vendor_attr { 9999 QCA_MPTA_HELPER_VENDOR_ATTR_INVALID = 0, 10000 /* Optional attribute used to update Zigbee state. 10001 * enum qca_mpta_helper_attr_zigbee_state. 10002 * NLA_U32 attribute. 10003 */ 10004 QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE = 1, 10005 /* Optional attribute used to configure WLAN duration for Shape-OCS 10006 * during interrupt. 10007 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION. 10008 * Value range 0 ~ 300 (ms). 10009 * NLA_U32 attribute. 10010 */ 10011 QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION = 2, 10012 /* Optional attribute used to configure non-WLAN duration for Shape-OCS 10013 * during interrupt. 10014 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION. 10015 * Value range 0 ~ 300 (ms). 10016 * NLA_U32 attribute. 10017 */ 10018 QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION = 3, 10019 /* Optional attribute used to configure WLAN duration for Shape-OCS 10020 * monitor period. 10021 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION. 10022 * Value range 0 ~ 300 (ms) 10023 * NLA_U32 attribute 10024 */ 10025 QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION = 4, 10026 /* Optional attribute used to configure non-WLAN duration for Shape-OCS 10027 * monitor period. 10028 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION. 10029 * Value range 0 ~ 300 (ms) 10030 * NLA_U32 attribute 10031 */ 10032 QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION = 5, 10033 /* Optional attribute used to configure OCS interrupt duration. 10034 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION. 10035 * Value range 1000 ~ 20000 (ms) 10036 * NLA_U32 attribute 10037 */ 10038 QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION = 6, 10039 /* Optional attribute used to configure OCS monitor duration. 10040 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION. 10041 * Value range 1000 ~ 20000 (ms) 10042 * NLA_U32 attribute 10043 */ 10044 QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION = 7, 10045 /* Optional attribute used to notify WLAN firmware the current Zigbee 10046 * channel. 10047 * Value range 11 ~ 26 10048 * NLA_U32 attribute 10049 */ 10050 QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_CHAN = 8, 10051 /* Optional attribute used to configure WLAN mute duration. 10052 * Value range 0 ~ 400 (ms) 10053 * NLA_U32 attribute 10054 */ 10055 QCA_MPTA_HELPER_VENDOR_ATTR_WLAN_MUTE_DURATION = 9, 10056 10057 /* keep last */ 10058 QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST, 10059 QCA_MPTA_HELPER_VENDOR_ATTR_MAX = 10060 QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1 10061 }; 10062 10063 /** 10064 * enum qca_wlan_vendor_beacon_reporting_op_types - Defines different types of 10065 * operations for which %QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING can be used. 10066 * Will be used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE. 10067 * 10068 * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START: Sent by userspace to the driver 10069 * to request the driver to start reporting Beacon frames. 10070 * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP: Sent by userspace to the driver to 10071 * request the driver to stop reporting Beacon frames. 10072 * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO: Sent by the driver to 10073 * userspace to report received Beacon frames. 10074 * @QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE: Sent by the driver to userspace 10075 * to indicate that the driver is going to pause reporting Beacon frames. 10076 */ 10077 enum qca_wlan_vendor_beacon_reporting_op_types { 10078 QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START = 0, 10079 QCA_WLAN_VENDOR_BEACON_REPORTING_OP_STOP = 1, 10080 QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO = 2, 10081 QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE = 3, 10082 }; 10083 10084 /** 10085 * enum qca_wlan_vendor_beacon_reporting_pause_reasons - Defines different types 10086 * of reasons for which the driver is pausing reporting Beacon frames. Will be 10087 * used by %QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON. 10088 * 10089 * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED: For unspecified 10090 * reasons. 10091 * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED: When the 10092 * driver/firmware is starting a scan. 10093 * @QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED: When the 10094 * driver/firmware disconnects from the ESS and indicates the disconnection to 10095 * userspace (non-seamless roaming case). This reason code will be used by the 10096 * driver/firmware to indicate stopping of beacon report events. Userspace will 10097 * need to start beacon reporting again (if desired) by sending vendor command 10098 * QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING with 10099 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE set to 10100 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START after the next connection is 10101 * completed. 10102 */ 10103 enum qca_wlan_vendor_beacon_reporting_pause_reasons { 10104 QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_UNSPECIFIED = 0, 10105 QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_SCAN_STARTED = 1, 10106 QCA_WLAN_VENDOR_BEACON_REPORTING_PAUSE_REASON_DISCONNECTED = 2, 10107 }; 10108 10109 /* 10110 * enum qca_wlan_vendor_attr_beacon_reporting_params - List of attributes used 10111 * in vendor sub-command QCA_NL80211_VENDOR_SUBCMD_BEACON_REPORTING. 10112 */ 10113 enum qca_wlan_vendor_attr_beacon_reporting_params { 10114 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_INVALID = 0, 10115 /* Specifies the type of operation that the vendor command/event is 10116 * intended for. Possible values for this attribute are defined in 10117 * enum qca_wlan_vendor_beacon_reporting_op_types. u32 attribute. 10118 */ 10119 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE = 1, 10120 /* Optionally set by userspace to request the driver to report Beacon 10121 * frames using asynchronous vendor events when the 10122 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10123 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. 10124 * If this flag is not set, the driver will only update Beacon frames in 10125 * cfg80211 scan cache but not send any vendor events. 10126 */ 10127 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_ACTIVE_REPORTING = 2, 10128 /* Optionally used by userspace to request the driver/firmware to report 10129 * Beacon frames periodically when the 10130 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10131 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. 10132 * u32 attribute, indicates the period of Beacon frames to be reported 10133 * and in the units of beacon interval. 10134 * If this attribute is missing in the command, then the default value 10135 * of 1 will be assumed by driver, i.e., to report every Beacon frame. 10136 * Zero is an invalid value. 10137 * If a valid value is received for this attribute, the driver will 10138 * update the cfg80211 scan cache periodically as per the value received 10139 * in this attribute in addition to updating the cfg80211 scan cache 10140 * when there is significant change in Beacon frame IEs. 10141 */ 10142 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PERIOD = 3, 10143 /* Used by the driver to encapsulate the SSID when the 10144 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10145 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. 10146 * u8 array with a maximum size of 32. 10147 * 10148 * When generating beacon report from non-MBSSID Beacon frame, the SSID 10149 * will be taken from the SSID element of the received Beacon frame. 10150 * 10151 * When generating beacon report from Multiple BSSID Beacon frame and if 10152 * the BSSID of the current connected BSS matches the BSSID of the 10153 * transmitting BSS, the SSID will be taken from the SSID element of the 10154 * received Beacon frame. 10155 * 10156 * When generating beacon report from Multiple BSSID Beacon frame and if 10157 * the BSSID of the current connected BSS matches the BSSID of one of 10158 * the* nontransmitting BSSs, the SSID will be taken from the SSID field 10159 * included in the nontransmitted BSS profile whose derived BSSID is 10160 * same as the BSSID of the current connected BSS. When there is no 10161 * nontransmitted BSS profile whose derived BSSID is same as the BSSID 10162 * of current connected* BSS, this attribute will not be present. 10163 */ 10164 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_SSID = 4, 10165 /* Used by the driver to encapsulate the BSSID of the AP to which STA is 10166 * currently connected to when the 10167 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10168 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array with a 10169 * fixed size of 6 bytes. 10170 * 10171 * When generating beacon report from a Multiple BSSID beacon and the 10172 * current connected BSSID matches one of the nontransmitted BSSIDs in a 10173 * Multiple BSSID set, this BSSID will be that particular nontransmitted 10174 * BSSID and not the transmitted BSSID (i.e., the transmitting address 10175 * of the Beacon frame). 10176 */ 10177 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BSSID = 5, 10178 /* Used by the driver to encapsulate the frequency in MHz on which 10179 * the Beacon frame was received when the 10180 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is 10181 * set to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. 10182 * u32 attribute. 10183 */ 10184 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_FREQ = 6, 10185 /* Used by the driver to encapsulate the Beacon interval 10186 * when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10187 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. 10188 * u16 attribute. The value will be copied from the Beacon frame and the 10189 * units are TUs. 10190 */ 10191 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BI = 7, 10192 /* Used by the driver to encapsulate the Timestamp field from the Beacon 10193 * frame when the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set 10194 * to QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. 10195 * u64 attribute. 10196 */ 10197 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_TSF = 8, 10198 /* Used by the driver to encapsulate the CLOCK_BOOTTIME when this 10199 * Beacon frame is received in the driver when the 10200 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10201 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u64 attribute, in 10202 * the units of nanoseconds. This value is expected to have accuracy of 10203 * about 10 ms. 10204 */ 10205 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_BOOTTIME_WHEN_RECEIVED = 9, 10206 /* Used by the driver to encapsulate the IEs of the Beacon frame from 10207 * which this event is generated when the 10208 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10209 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_BEACON_INFO. u8 array. 10210 */ 10211 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_IES = 10, 10212 /* Used by the driver to specify the reason for the driver/firmware to 10213 * pause sending beacons to userspace when the 10214 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10215 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. Possible values are 10216 * defined in enum qca_wlan_vendor_beacon_reporting_pause_reasons, u32 10217 * attribute. 10218 */ 10219 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_PAUSE_REASON = 11, 10220 /* Used by the driver to specify whether the driver will automatically 10221 * resume reporting beacon events to userspace later (for example after 10222 * the ongoing off-channel activity is completed etc.) when the 10223 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10224 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE. NLA_FLAG attribute. 10225 */ 10226 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES = 12, 10227 /* Optionally set by userspace to request the driver not to resume 10228 * beacon reporting after a pause is completed, when the 10229 * QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_OP_TYPE is set to 10230 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START. NLA_FLAG attribute. 10231 * If this flag is set, the driver will not resume beacon reporting 10232 * after any pause in beacon reporting is completed. Userspace has to 10233 * send QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command again in order 10234 * to initiate beacon reporting again. If this flag is set in the recent 10235 * QCA_WLAN_VENDOR_BEACON_REPORTING_OP_START command, then in the 10236 * subsequent QCA_WLAN_VENDOR_BEACON_REPORTING_OP_PAUSE event (if any) 10237 * the QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_AUTO_RESUMES shall not be 10238 * set by the driver. Setting this flag until and unless there is a 10239 * specific need is not recommended as there is a chance of some beacons 10240 * received after pause command and next start command being not 10241 * reported. 10242 */ 10243 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_DO_NOT_RESUME = 13, 10244 10245 /* Keep last */ 10246 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST, 10247 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_MAX = 10248 QCA_WLAN_VENDOR_ATTR_BEACON_REPORTING_LAST - 1 10249 }; 10250 10251 /** 10252 * enum qca_vendor_interop_issues_ap_type - Interop issue types 10253 * This enum defines the valid set of values of interop issue types. These 10254 * values are used by attribute %QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE. 10255 * 10256 * @QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS: The AP has power save interop issue 10257 * when the STA's Qpower feature is enabled. 10258 */ 10259 enum qca_vendor_interop_issues_ap_type { 10260 QCA_VENDOR_INTEROP_ISSUES_AP_INVALID = 0, 10261 QCA_VENDOR_INTEROP_ISSUES_AP_ON_STA_PS = 1, 10262 }; 10263 10264 /** 10265 * enum qca_vendor_attr_interop_issues_ap - attribute for AP with interop issues 10266 * Values are used by %QCA_NL80211_VENDOR_SUBCMD_INTEROP_ISSUES_AP. 10267 * 10268 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID: Invalid value 10269 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE: Interop issue type 10270 * 32-bit unsigned value. The values defined in enum 10271 * qca_vendor_interop_issues_ap_type are used. 10272 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST: APs' BSSID container 10273 * array of nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID attributes. 10274 * It is present and mandatory for the command but is not used for the event 10275 * since only a single BSSID is reported in an event. 10276 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID: AP's BSSID 6-byte MAC address. 10277 * It is used within the nested QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST 10278 * attribute in command case and without such encapsulation in the event case. 10279 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST: last value 10280 * @QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX: max value 10281 */ 10282 enum qca_vendor_attr_interop_issues_ap { 10283 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_INVALID, 10284 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_TYPE, 10285 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_LIST, 10286 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_BSSID, 10287 /* keep last */ 10288 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST, 10289 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_MAX = 10290 QCA_WLAN_VENDOR_ATTR_INTEROP_ISSUES_AP_AFTER_LAST - 1 10291 }; 10292 10293 /** 10294 * enum qca_vendor_oem_device_type - Represents the target device in firmware. 10295 * It is used by QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO. 10296 * 10297 * @QCA_VENDOR_OEM_DEVICE_VIRTUAL: The command is intended for 10298 * a virtual device. 10299 * 10300 * @QCA_VENDOR_OEM_DEVICE_PHYSICAL: The command is intended for 10301 * a physical device. 10302 */ 10303 enum qca_vendor_oem_device_type { 10304 QCA_VENDOR_OEM_DEVICE_VIRTUAL = 0, 10305 QCA_VENDOR_OEM_DEVICE_PHYSICAL = 1, 10306 }; 10307 10308 /** 10309 * enum qca_wlan_vendor_attr_oem_data_params - Used by the vendor command/event 10310 * QCA_NL80211_VENDOR_SUBCMD_OEM_DATA. 10311 * 10312 * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA: This NLA_BINARY attribute is 10313 * used to set/query the data to/from the firmware. On query, the same 10314 * attribute is used to carry the respective data in the reply sent by the 10315 * driver to userspace. The request to set/query the data and the format of the 10316 * respective data from the firmware are embedded in the attribute. The 10317 * maximum size of the attribute payload is 1024 bytes. 10318 * Userspace has to set the QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED 10319 * attribute when the data is queried from the firmware. 10320 * 10321 * @QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO: The binary blob will be routed 10322 * based on this field. This optional attribute is included to specify whether 10323 * the device type is a virtual device or a physical device for the 10324 * command/event. This attribute can be omitted for a virtual device (default) 10325 * command/event. 10326 * This u8 attribute is used to carry information for the device type using 10327 * values defined by enum qca_vendor_oem_device_type. 10328 * 10329 * @QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED: This NLA_FLAG attribute 10330 * is set when the userspace queries data from the firmware. This attribute 10331 * should not be set when userspace sets the OEM data to the firmware. 10332 */ 10333 enum qca_wlan_vendor_attr_oem_data_params { 10334 QCA_WLAN_VENDOR_ATTR_OEM_DATA_INVALID = 0, 10335 QCA_WLAN_VENDOR_ATTR_OEM_DATA_CMD_DATA = 1, 10336 QCA_WLAN_VENDOR_ATTR_OEM_DEVICE_INFO = 2, 10337 QCA_WLAN_VENDOR_ATTR_OEM_DATA_RESPONSE_EXPECTED = 3, 10338 10339 /* keep last */ 10340 QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST, 10341 QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_MAX = 10342 QCA_WLAN_VENDOR_ATTR_OEM_DATA_PARAMS_AFTER_LAST - 1 10343 }; 10344 10345 /** 10346 * enum qca_wlan_vendor_attr_avoid_frequency_ext - Defines attributes to be 10347 * used with vendor command/event QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY_EXT. 10348 * 10349 * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE: Required 10350 * Nested attribute containing multiple ranges with following attributes: 10351 * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START, 10352 * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END, and 10353 * QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM. 10354 * 10355 * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START: Required (u32) 10356 * Starting center frequency in MHz. 10357 * 10358 * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END: Required (u32) 10359 * Ending center frequency in MHz. 10360 * 10361 * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM: 10362 * s32 attribute, optional. It is a per frequency range attribute. 10363 * The maximum TX power limit from user space is to be applied on an 10364 * unrestricted interface for corresponding frequency range. It is also 10365 * possible that the actual TX power may be even lower than this cap due to 10366 * other considerations such as regulatory compliance, SAR, etc. In absence of 10367 * this attribute the driver shall follow current behavior which means 10368 * interface (SAP/P2P) function can keep operating on an unsafe channel with TX 10369 * power derived by the driver based on regulatory/SAR during interface up. 10370 * 10371 * @QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK: 10372 * u32 attribute, optional. Indicates all the interface types which are 10373 * restricted for all frequency ranges provided in 10374 * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START and 10375 * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END. 10376 * This attribute encapsulates bitmasks of interface types defined in 10377 * enum nl80211_iftype. If an interface is marked as restricted the driver must 10378 * move to a safe channel and if no safe channel is available the driver shall 10379 * terminate that interface functionality. In absence of this attribute, 10380 * interface (SAP/P2P) can still continue operating on an unsafe channel with 10381 * TX power limit derived from either 10382 * %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM or based on 10383 * regulatory/SAE limits if %QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM 10384 * is not provided. 10385 */ 10386 enum qca_wlan_vendor_attr_avoid_frequency_ext { 10387 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_INVALID = 0, 10388 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_RANGE = 1, 10389 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_START = 2, 10390 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_END = 3, 10391 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_POWER_CAP_DBM = 4, 10392 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_IFACES_BITMASK = 5, 10393 10394 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST, 10395 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_MAX = 10396 QCA_WLAN_VENDOR_ATTR_AVOID_FREQUENCY_AFTER_LAST - 1 10397 }; 10398 10399 /* 10400 * enum qca_wlan_vendor_attr_add_sta_node_params - Used by the vendor command 10401 * QCA_NL80211_VENDOR_SUBCMD_ADD_STA_NODE. 10402 */ 10403 enum qca_wlan_vendor_attr_add_sta_node_params { 10404 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_INVALID = 0, 10405 /* 6 byte MAC address of STA */ 10406 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_MAC_ADDR = 1, 10407 /* Authentication algorithm used by the station of size u16; 10408 * defined in enum nl80211_auth_type. 10409 */ 10410 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_AUTH_ALGO = 2, 10411 10412 /* keep last */ 10413 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST, 10414 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_MAX = 10415 QCA_WLAN_VENDOR_ATTR_ADD_STA_NODE_PARAM_AFTER_LAST - 1 10416 }; 10417 10418 /** 10419 * enum qca_btc_chain_mode - Specifies BT coex chain mode. 10420 * This enum defines the valid set of values of BT coex chain mode. 10421 * These values are used by attribute %QCA_VENDOR_ATTR_BTC_CHAIN_MODE of 10422 * %QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. 10423 * 10424 * @QCA_BTC_CHAIN_SHARED: chains of BT and WLAN 2.4G are shared. 10425 * @QCA_BTC_CHAIN_SEPARATED: chains of BT and WLAN 2.4G are separated. 10426 */ 10427 enum qca_btc_chain_mode { 10428 QCA_BTC_CHAIN_SHARED = 0, 10429 QCA_BTC_CHAIN_SEPARATED = 1, 10430 }; 10431 10432 /** 10433 * enum qca_vendor_attr_btc_chain_mode - Specifies attributes for BT coex 10434 * chain mode. 10435 * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_BTC_CHAIN_MODE. 10436 * 10437 * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE: u32 attribute. 10438 * Indicates the BT coex chain mode, are 32-bit values from 10439 * enum qca_btc_chain_mode. This attribute is mandatory. 10440 * 10441 * @QCA_VENDOR_ATTR_COEX_BTC_CHAIN_MODE_RESTART: flag attribute. 10442 * If set, vdev should be restarted when BT coex chain mode is updated. 10443 * This attribute is optional. 10444 */ 10445 enum qca_vendor_attr_btc_chain_mode { 10446 QCA_VENDOR_ATTR_BTC_CHAIN_MODE_INVALID = 0, 10447 QCA_VENDOR_ATTR_BTC_CHAIN_MODE = 1, 10448 QCA_VENDOR_ATTR_BTC_CHAIN_MODE_RESTART = 2, 10449 10450 /* Keep last */ 10451 QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST, 10452 QCA_VENDOR_ATTR_BTC_CHAIN_MODE_MAX = 10453 QCA_VENDOR_ATTR_BTC_CHAIN_MODE_LAST - 1, 10454 }; 10455 10456 /** 10457 * enum qca_vendor_wlan_sta_flags - Station feature flags 10458 * Bits will be set to 1 if the corresponding features are enabled. 10459 * @QCA_VENDOR_WLAN_STA_FLAG_AMPDU: AMPDU is enabled for the station 10460 * @QCA_VENDOR_WLAN_STA_FLAG_TX_STBC: TX Space-time block coding is enabled 10461 for the station 10462 * @QCA_VENDOR_WLAN_STA_FLAG_RX_STBC: RX Space-time block coding is enabled 10463 for the station 10464 */ 10465 enum qca_vendor_wlan_sta_flags { 10466 QCA_VENDOR_WLAN_STA_FLAG_AMPDU = BIT(0), 10467 QCA_VENDOR_WLAN_STA_FLAG_TX_STBC = BIT(1), 10468 QCA_VENDOR_WLAN_STA_FLAG_RX_STBC = BIT(2), 10469 }; 10470 10471 /** 10472 * enum qca_vendor_wlan_sta_guard_interval - Station guard interval 10473 * @QCA_VENDOR_WLAN_STA_GI_800_NS: Legacy normal guard interval 10474 * @QCA_VENDOR_WLAN_STA_GI_400_NS: Legacy short guard interval 10475 * @QCA_VENDOR_WLAN_STA_GI_1600_NS: Guard interval used by HE 10476 * @QCA_VENDOR_WLAN_STA_GI_3200_NS: Guard interval used by HE 10477 */ 10478 enum qca_vendor_wlan_sta_guard_interval { 10479 QCA_VENDOR_WLAN_STA_GI_800_NS = 0, 10480 QCA_VENDOR_WLAN_STA_GI_400_NS = 1, 10481 QCA_VENDOR_WLAN_STA_GI_1600_NS = 2, 10482 QCA_VENDOR_WLAN_STA_GI_3200_NS = 3, 10483 }; 10484 10485 /** 10486 * enum qca_wlan_vendor_attr_get_sta_info - Defines attributes 10487 * used by QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command. 10488 * 10489 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC: 10490 * Required attribute in request for AP mode only, 6-byte MAC address, 10491 * corresponding to the station's MAC address for which information is 10492 * requested. For STA mode this is not required as the info always correspond 10493 * to the self STA and the current/last association. 10494 * 10495 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS: 10496 * Optionally used in response, u32 attribute, contains a bitmap of different 10497 * fields defined in enum qca_vendor_wlan_sta_flags, used in AP mode only. 10498 * 10499 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL: 10500 * Optionally used in response, u32 attribute, possible values are defined in 10501 * enum qca_vendor_wlan_sta_guard_interval, used in AP mode only. 10502 * Guard interval used by the station. 10503 * 10504 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT: 10505 * Optionally used in response, u32 attribute, used in AP mode only. 10506 * Value indicates the number of data frames received from station with retry 10507 * bit set to 1 in FC. 10508 * 10509 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT: 10510 * Optionally used in response, u32 attribute, used in AP mode only. 10511 * Counter for number of data frames with broadcast or multicast address in 10512 * the destination address received from the station. 10513 * 10514 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED: 10515 * Optionally used in response, u32 attribute, used in both STA and AP modes. 10516 * Value indicates the number of data frames successfully transmitted only 10517 * after retrying the packets and for which the TX status has been updated 10518 * back to host from target. 10519 * 10520 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED: 10521 * Optionally used in response, u32 attribute, used in both STA and AP mode. 10522 * Value indicates the number of data frames not transmitted successfully even 10523 * after retrying the packets for the number of times equal to the total number 10524 * of retries allowed for that packet and for which the TX status has been 10525 * updated back to host from target. 10526 * 10527 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL: 10528 * Optionally used in response, u32 attribute, used in AP mode only. 10529 * Counter in the target for the number of data frames successfully transmitted 10530 * to the station. 10531 * 10532 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY: 10533 * Optionally used in response, u32 attribute, used in AP mode only. 10534 * Value indicates the number of data frames successfully transmitted only 10535 * after retrying the packets. 10536 * 10537 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED: 10538 * Optionally used in response, u32 attribute, used in both STA & AP mode. 10539 * Value indicates the number of data frames not transmitted successfully even 10540 * after retrying the packets for the number of times equal to the total number 10541 * of retries allowed for that packet. 10542 * 10543 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT: u32, used in 10544 * the STA mode only. Represent the number of probe requests sent by the STA 10545 * while attempting to roam on missing certain number of beacons from the 10546 * connected AP. If queried in the disconnected state, this represents the 10547 * count for the last connected state. 10548 * 10549 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT: u32, used in 10550 * the STA mode. Represent the number of probe responses received by the station 10551 * while attempting to roam on missing certain number of beacons from the 10552 * connected AP. When queried in the disconnected state, this represents the 10553 * count when in last connected state. 10554 * 10555 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT: u32, used in the 10556 * STA mode only. Represents the total number of frames sent out by STA 10557 * including Data, ACK, RTS, CTS, Control Management. This data is maintained 10558 * only for the connect session. Represents the count of last connected session, 10559 * when queried in the disconnected state. 10560 * 10561 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT: u32, used in the STA mode. 10562 * Total number of RTS sent out by the STA. This data is maintained per connect 10563 * session. Represents the count of last connected session, when queried in the 10564 * disconnected state. 10565 * 10566 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT: u32, used in the 10567 * STA mode.Represent the number of RTS transmission failure that reach retry 10568 * limit. This data is maintained per connect session. Represents the count of 10569 * last connected session, when queried in the disconnected state. 10570 * 10571 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT: u32, used in 10572 * the STA mode. Represent the total number of non aggregated frames transmitted 10573 * by the STA. This data is maintained per connect session. Represents the count 10574 * of last connected session, when queried in the disconnected state. 10575 * 10576 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT: u32, used in the 10577 * STA mode. Represent the total number of aggregated frames transmitted by the 10578 * STA. This data is maintained per connect session. Represents the count of 10579 * last connected session, when queried in the disconnected state. 10580 * 10581 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT: u32, used in 10582 * the STA mode. Represents the number of received frames with a good PLCP. This 10583 * data is maintained per connect session. Represents the count of last 10584 * connected session, when queried in the disconnected state. 10585 * 10586 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT: u32, 10587 * used in the STA mode. Represents the number of occasions that no valid 10588 * delimiter is detected by A-MPDU parser. This data is maintained per connect 10589 * session. Represents the count of last connected session, when queried in the 10590 * disconnected state. 10591 * 10592 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT: u32, used in the 10593 * STA mode. Represents the number of frames for which CRC check failed in the 10594 * MAC. This data is maintained per connect session. Represents the count of 10595 * last connected session, when queried in the disconnected state. 10596 * 10597 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT: u32, used in the 10598 * STA mode. Represents the number of unicast ACKs received with good FCS. This 10599 * data is maintained per connect session. Represents the count of last 10600 * connected session, when queried in the disconnected state. 10601 * 10602 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT: u32, used in the STA 10603 * mode. Represents the number of received Block Acks. This data is maintained 10604 * per connect session. Represents the count of last connected session, when 10605 * queried in the disconnected state. 10606 * 10607 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT: u32, used in the STA 10608 * mode. Represents the number of beacons received from the connected BSS. This 10609 * data is maintained per connect session. Represents the count of last 10610 * connected session, when queried in the disconnected state. 10611 * 10612 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT: u32, used in the 10613 * STA mode. Represents the number of beacons received by the other BSS when in 10614 * connected state (through the probes done by the STA). This data is maintained 10615 * per connect session. Represents the count of last connected session, when 10616 * queried in the disconnected state. 10617 * 10618 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT: u64, used in 10619 * the STA mode. Represents the number of received DATA frames with good FCS and 10620 * matching Receiver Address when in connected state. This data is maintained 10621 * per connect session. Represents the count of last connected session, when 10622 * queried in the disconnected state. 10623 * 10624 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT: u32, used in the 10625 * STA mode. Represents the number of RX Data multicast frames dropped by the HW 10626 * when in the connected state. This data is maintained per connect session. 10627 * Represents the count of last connected session, when queried in the 10628 * disconnected state. 10629 * 10630 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS: u32, used in the 10631 * STA mode. This represents the target power in dBm for the transmissions done 10632 * to the AP in 2.4 GHz at 1 Mbps (DSSS) rate. This data is maintained per 10633 * connect session. Represents the count of last connected session, when 10634 * queried in the disconnected state. 10635 * 10636 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS: u32, used in the 10637 * STA mode. This represents the Target power in dBm for transmissions done to 10638 * the AP in 2.4 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect 10639 * session. Represents the count of last connected session, when queried in the 10640 * disconnected state. 10641 * 10642 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0: u32, used in the 10643 * STA mode. This represents the Target power in dBm for transmissions done to 10644 * the AP in 2.4 GHz at MCS0 rate. This data is maintained per connect session. 10645 * Represents the count of last connected session, when queried in the 10646 * disconnected state. 10647 * 10648 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS: u32, used in the 10649 * STA mode. This represents the Target power in dBm for transmissions done to 10650 * the AP in 5 GHz at 6 Mbps (OFDM) rate. This data is maintained per connect 10651 * session. Represents the count of last connected session, when queried in 10652 * the disconnected state. 10653 * 10654 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0: u32, used in the 10655 * STA mode. This represents the Target power in dBm for for transmissions done 10656 * to the AP in 5 GHz at MCS0 rate. This data is maintained per connect session. 10657 * Represents the count of last connected session, when queried in the 10658 * disconnected state. 10659 * 10660 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT: u32, used 10661 * in the STA mode. This represents the Nested attribute representing the 10662 * overflow counts of each receive buffer allocated to the hardware during the 10663 * STA's connection. The number of hw buffers might vary for each WLAN 10664 * solution and hence this attribute represents the nested array of all such 10665 * HW buffer count. This data is maintained per connect session. Represents 10666 * the count of last connected session, when queried in the disconnected state. 10667 * 10668 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER: u32, Max TX power (dBm) 10669 * allowed as per the regulatory requirements for the current or last connected 10670 * session. Used in the STA mode. 10671 * 10672 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER: u32, Latest TX power 10673 * (dBm) used by the station in its latest unicast frame while communicating 10674 * to the AP in the connected state. When queried in the disconnected state, 10675 * this represents the TX power used by the STA with last AP communication 10676 * when in connected state. 10677 * 10678 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL: u32, Adaptive noise immunity 10679 * level used to adjust the RX sensitivity. Represents the current ANI level 10680 * when queried in the connected state. When queried in the disconnected 10681 * state, this corresponds to the latest ANI level at the instance of 10682 * disconnection. 10683 * 10684 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES: Binary attribute containing 10685 * the raw information elements from Beacon frames. Represents the Beacon frames 10686 * of the current BSS in the connected state. When queried in the disconnected 10687 * state, these IEs correspond to the last connected BSSID. 10688 * 10689 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES: Binary attribute 10690 * containing the raw information elements from Probe Response frames. 10691 * Represents the Probe Response frames of the current BSS in the connected 10692 * state. When queried in the disconnected state, these IEs correspond to the 10693 * last connected BSSID. 10694 * 10695 * @QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON: u32, Driver 10696 * disconnect reason for the last disconnection if the disconnection is 10697 * triggered from the host driver. The values are referred from 10698 * enum qca_disconnect_reason_codes. 10699 * 10700 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT: u32, used in STA mode 10701 * only. This represents the number of group addressed robust management frames 10702 * received from this station with an invalid MIC or a missing MME when PMF is 10703 * enabled. 10704 * 10705 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT: u32, used in STA mode 10706 * only. This represents the number of group addressed robust management frames 10707 * received from this station with the packet number less than or equal to the 10708 * last received packet number when PMF is enabled. 10709 * 10710 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT: u32, used in STA 10711 * mode only. This represents the number of Beacon frames received from this 10712 * station with an invalid MIC or a missing MME when beacon protection is 10713 * enabled. 10714 * 10715 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT: u32, used in STA mode 10716 * only. This represents number of Beacon frames received from this station with 10717 * the packet number less than or equal to the last received packet number when 10718 * beacon protection is enabled. 10719 * 10720 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE: u32, used in 10721 * STA mode only. The driver uses this attribute to populate the connection 10722 * failure reason codes and the values are defined in 10723 * enum qca_sta_connect_fail_reason_codes. Userspace applications can send 10724 * QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO vendor command after receiving 10725 * a connection failure indication from the driver. The driver shall not 10726 * include this attribute in response to the 10727 * QCA_NL80211_VENDOR_SUBCMD_GET_STA_INFO command if there is no connection 10728 * failure observed in the last attempted connection. 10729 * 10730 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE: u32, latest TX rate (Kbps) 10731 * used by the station in its last TX frame while communicating to the AP in the 10732 * connected state. When queried in the disconnected state, this represents the 10733 * rate used by the STA in the last TX frame to the AP when it was connected. 10734 * This attribute is used for STA mode only. 10735 * 10736 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX: u32, used in STA mode only. 10737 * This represents the rate index used by the STA for the last TX frame to the 10738 * AP. When queried in the disconnected state, this gives the last RIX used by 10739 * the STA in the last TX frame to the AP when it was connected. 10740 * 10741 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT: u32, used in STA 10742 * mode only. This represents the number of times the STA TSF goes out of sync 10743 * from the AP after the connection. If queried in the disconnected state, this 10744 * gives the count of TSF out of sync for the last connection. 10745 * 10746 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON: u32, used in STA 10747 * mode only. This represents the roam trigger reason for the last roaming 10748 * attempted by the firmware. This can be queried either in connected state or 10749 * disconnected state. Each bit of this attribute represents the different 10750 * roam trigger reason code which are defined in enum qca_vendor_roam_triggers. 10751 * 10752 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON: u32, used in STA mode 10753 * only. This represents the roam fail reason for the last failed roaming 10754 * attempt by the firmware. Different roam failure reason codes are specified 10755 * in enum qca_vendor_roam_fail_reasons. This can be queried either in 10756 * connected state or disconnected state. 10757 * 10758 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON: u32, used in 10759 * STA mode only. This represents the roam invoke fail reason for the last 10760 * failed roam invoke. Different roam invoke failure reason codes 10761 * are specified in enum qca_vendor_roam_invoke_fail_reasons. This can be 10762 * queried either in connected state or disconnected state. 10763 * 10764 * @QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY: u32, used in STA mode only. 10765 * This represents the average congestion duration of uplink frames in MAC 10766 * queue in unit of ms. This can be queried either in connected state or 10767 * disconnected state. 10768 */ 10769 enum qca_wlan_vendor_attr_get_sta_info { 10770 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_INVALID = 0, 10771 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAC = 1, 10772 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_FLAGS = 2, 10773 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_GUARD_INTERVAL = 3, 10774 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_RETRY_COUNT = 4, 10775 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BC_MC_COUNT = 5, 10776 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_SUCCEED = 6, 10777 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RETRY_EXHAUSTED = 7, 10778 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_TOTAL = 8, 10779 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY = 9, 10780 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_RETRY_EXHAUSTED = 10, 10781 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_PROBE_REQ_BMISS_COUNT = 11, 10782 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_PROBE_RESP_BMISS_COUNT = 12, 10783 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_TX_ALL_COUNT = 13, 10784 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_COUNT = 14, 10785 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_RTS_RETRY_FAIL_COUNT = 15, 10786 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_NON_AGGREGATED_COUNT = 16, 10787 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TX_DATA_AGGREGATED_COUNT = 17, 10788 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_GOOD_PLCP_COUNT = 18, 10789 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_INVALID_DELIMITER_COUNT = 19, 10790 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_FRAMES_CRC_FAIL_COUNT = 20, 10791 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_ACKS_GOOD_FCS_COUNT = 21, 10792 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BLOCKACK_COUNT = 22, 10793 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_BEACON_COUNT = 23, 10794 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_OTHER_BEACON_COUNT = 24, 10795 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_UCAST_DATA_GOOD_FCS_COUNT = 25, 10796 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_DATA_BC_MC_DROP_COUNT = 26, 10797 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_1MBPS = 27, 10798 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_6MBPS = 28, 10799 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_24G_MCS0 = 29, 10800 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_6MBPS = 30, 10801 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TARGET_POWER_5G_MCS0 = 31, 10802 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_RX_HW_BUFFERS_OVERFLOW_COUNT = 32, 10803 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX_TX_POWER = 33, 10804 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_POWER = 34, 10805 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ANI_LEVEL = 35, 10806 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_IES = 36, 10807 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_PROBE_RESP_IES = 37, 10808 QCA_WLAN_VENDOR_ATTR_GET_STA_DRIVER_DISCONNECT_REASON = 38, 10809 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_MIC_ERROR_COUNT = 39, 10810 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BIP_REPLAY_COUNT = 40, 10811 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_MIC_ERROR_COUNT = 41, 10812 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_BEACON_REPLAY_COUNT = 42, 10813 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE = 43, 10814 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_TX_RATE = 44, 10815 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_LATEST_RIX = 45, 10816 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_TSF_OUT_OF_SYNC_COUNT = 46, 10817 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_TRIGGER_REASON = 47, 10818 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_FAIL_REASON = 48, 10819 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_ROAM_INVOKE_FAIL_REASON = 49, 10820 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_UPLINK_DELAY = 50, 10821 10822 /* keep last */ 10823 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST, 10824 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_MAX = 10825 QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_AFTER_LAST - 1, 10826 }; 10827 10828 /** 10829 * enum qca_wlan_vendor_attr_update_sta_info - Defines attributes 10830 * used by QCA_NL80211_VENDOR_SUBCMD_UPDATE_STA_INFO vendor command. 10831 * 10832 * @QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS: Type is NLA_UNSPEC. 10833 * Used in STA mode. This attribute represents the list of channel center 10834 * frequencies in MHz (u32) the station has learnt during the last connection 10835 * or roaming attempt. This information shall not signify the channels for 10836 * an explicit scan request from the user space. Host drivers can update this 10837 * information to the user space in both connected and disconnected state. 10838 * In the disconnected state this information shall signify the channels 10839 * scanned in the last connection/roam attempt that lead to the disconnection. 10840 */ 10841 enum qca_wlan_vendor_attr_update_sta_info { 10842 QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_INVALID = 0, 10843 QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_CONNECT_CHANNELS = 1, 10844 10845 /* keep last */ 10846 QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST, 10847 QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_MAX = 10848 QCA_WLAN_VENDOR_ATTR_UPDATE_STA_INFO_AFTER_LAST - 1, 10849 }; 10850 10851 /** 10852 * enum qca_disconnect_reason_codes - Specifies driver disconnect reason codes. 10853 * Used when the driver triggers the STA to disconnect from the AP. 10854 * 10855 * @QCA_DISCONNECT_REASON_UNSPECIFIED: The host driver triggered the 10856 * disconnection with the AP due to unspecified reasons. 10857 * 10858 * @QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE: The host driver triggered the 10859 * disconnection with the AP due to a roaming failure. This roaming is triggered 10860 * internally (host driver/firmware). 10861 * 10862 * @QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE: The driver disconnected from 10863 * the AP when the user/external triggered roaming fails. 10864 * 10865 * @QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE: This reason code is used 10866 * by the host driver whenever gateway reachability failure is detected and the 10867 * driver disconnects with AP. 10868 * 10869 * @QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA: The driver disconnected from 10870 * the AP on a channel switch announcement from it with an unsupported channel. 10871 * 10872 * @QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR: On a concurrent AP start 10873 * with indoor channels disabled and if the STA is connected on one of these 10874 * disabled channels, the host driver disconnected the STA with this reason 10875 * code. 10876 * 10877 * @QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED: Disconnection due to an 10878 * explicit request from the user to disable the current operating channel. 10879 * 10880 * @QCA_DISCONNECT_REASON_DEVICE_RECOVERY: STA disconnected from the AP due to 10881 * the internal host driver/firmware recovery. 10882 * 10883 * @QCA_DISCONNECT_REASON_KEY_TIMEOUT: The driver triggered the disconnection on 10884 * a timeout for the key installations from the user space. 10885 * 10886 * @QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE: The dDriver disconnected the 10887 * STA on a band change request from the user space to a different band from the 10888 * current operation channel/band. 10889 * 10890 * @QCA_DISCONNECT_REASON_IFACE_DOWN: The STA disconnected from the AP on an 10891 * interface down trigger from the user space. 10892 * 10893 * @QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL: The host driver disconnected the 10894 * STA on getting continuous transmission failures for multiple Data frames. 10895 * 10896 * @QCA_DISCONNECT_REASON_PEER_INACTIVITY: The STA does a keep alive 10897 * notification to the AP by transmitting NULL/G-ARP frames. This disconnection 10898 * represents inactivity from AP on such transmissions. 10899 10900 * @QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT: This reason code is used on 10901 * disconnection when SA Query times out (AP does not respond to SA Query). 10902 * 10903 * @QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE: The host driver disconnected the 10904 * STA on missing the beacons continuously from the AP. 10905 * 10906 * @QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE: Disconnection due to STA not 10907 * able to move to the channel mentioned by the AP in CSA. 10908 * 10909 * @QCA_DISCONNECT_REASON_USER_TRIGGERED: User triggered disconnection. 10910 */ 10911 enum qca_disconnect_reason_codes { 10912 QCA_DISCONNECT_REASON_UNSPECIFIED = 0, 10913 QCA_DISCONNECT_REASON_INTERNAL_ROAM_FAILURE = 1, 10914 QCA_DISCONNECT_REASON_EXTERNAL_ROAM_FAILURE = 2, 10915 QCA_DISCONNECT_REASON_GATEWAY_REACHABILITY_FAILURE = 3, 10916 QCA_DISCONNECT_REASON_UNSUPPORTED_CHANNEL_CSA = 4, 10917 QCA_DISCONNECT_REASON_OPER_CHANNEL_DISABLED_INDOOR = 5, 10918 QCA_DISCONNECT_REASON_OPER_CHANNEL_USER_DISABLED = 6, 10919 QCA_DISCONNECT_REASON_DEVICE_RECOVERY = 7, 10920 QCA_DISCONNECT_REASON_KEY_TIMEOUT = 8, 10921 QCA_DISCONNECT_REASON_OPER_CHANNEL_BAND_CHANGE = 9, 10922 QCA_DISCONNECT_REASON_IFACE_DOWN = 10, 10923 QCA_DISCONNECT_REASON_PEER_XRETRY_FAIL = 11, 10924 QCA_DISCONNECT_REASON_PEER_INACTIVITY = 12, 10925 QCA_DISCONNECT_REASON_SA_QUERY_TIMEOUT = 13, 10926 QCA_DISCONNECT_REASON_BEACON_MISS_FAILURE = 14, 10927 QCA_DISCONNECT_REASON_CHANNEL_SWITCH_FAILURE = 15, 10928 QCA_DISCONNECT_REASON_USER_TRIGGERED = 16, 10929 }; 10930 10931 /** 10932 * enum qca_wlan_vendor_attr_driver_disconnect_reason - Defines attributes 10933 * used by %QCA_NL80211_VENDOR_SUBCMD_DRIVER_DISCONNECT_REASON vendor command. 10934 * 10935 * @QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE: u32 attribute. 10936 * This attribute represents the driver specific reason codes (local 10937 * driver/firmware initiated reasons for disconnection) defined 10938 * in enum qca_disconnect_reason_codes. 10939 */ 10940 enum qca_wlan_vendor_attr_driver_disconnect_reason { 10941 QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_INVALID = 0, 10942 QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASCON_CODE = 1, 10943 10944 /* keep last */ 10945 QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST, 10946 QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_MAX = 10947 QCA_WLAN_VENDOR_ATTR_DRIVER_DISCONNECT_REASON_AFTER_LAST - 1, 10948 }; 10949 10950 /** 10951 * enum qca_wlan_tspec_operation - Operation of the config TSPEC request 10952 * 10953 * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION. 10954 */ 10955 enum qca_wlan_tspec_operation { 10956 QCA_WLAN_TSPEC_ADD = 0, 10957 QCA_WLAN_TSPEC_DEL = 1, 10958 QCA_WLAN_TSPEC_GET = 2, 10959 }; 10960 10961 /** 10962 * enum qca_wlan_tspec_direction - Direction in TSPEC 10963 * As what is defined in IEEE Std 802.11-2016, Table 9-139. 10964 * 10965 * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION. 10966 */ 10967 enum qca_wlan_tspec_direction { 10968 QCA_WLAN_TSPEC_DIRECTION_UPLINK = 0, 10969 QCA_WLAN_TSPEC_DIRECTION_DOWNLINK = 1, 10970 QCA_WLAN_TSPEC_DIRECTION_DIRECT = 2, 10971 QCA_WLAN_TSPEC_DIRECTION_BOTH = 3, 10972 }; 10973 10974 /** 10975 * enum qca_wlan_tspec_ack_policy - MAC acknowledgement policy in TSPEC 10976 * As what is defined in IEEE Std 802.11-2016, Table 9-141. 10977 * 10978 * Values for %QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY. 10979 */ 10980 enum qca_wlan_tspec_ack_policy { 10981 QCA_WLAN_TSPEC_NORMAL_ACK = 0, 10982 QCA_WLAN_TSPEC_NO_ACK = 1, 10983 /* Reserved */ 10984 QCA_WLAN_TSPEC_BLOCK_ACK = 3, 10985 }; 10986 10987 /** 10988 * enum qca_wlan_vendor_attr_config_tspec - Defines attributes 10989 * used by %QCA_NL80211_VENDOR_SUBCMD_CONFIG_TSPEC vendor command. 10990 * 10991 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION: 10992 * u8 attribute. Specify the TSPEC operation of this request. Possible values 10993 * are defined in enum qca_wlan_tspec_operation. 10994 * Mandatory attribute for all kinds of config TSPEC requests. 10995 * 10996 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID: 10997 * u8 attribute. TS ID. Possible values are 0-7. 10998 * Applicable for operation: QCA_WLAN_TSPEC_ADD, QCA_WLAN_TSPEC_DEL, 10999 * QCA_WLAN_TSPEC_GET. A mandatory attribute. 11000 * 11001 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION: 11002 * u8 attribute. Direction of data carried by the TS. Possible values are 11003 * defined in enum qca_wlan_tspec_direction. 11004 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11005 * 11006 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD: 11007 * Flag attribute. Indicate whether APSD is enabled for the traffic associated 11008 * with the TS. set - enabled, not set - disabled. 11009 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11010 * 11011 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY: 11012 * u8 attribute. User priority to be used for the transport of MSDUs/A-MSDUs 11013 * belonging to this TS. Possible values are 0-7. 11014 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11015 * 11016 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY: 11017 * u8 attribute. Indicate whether MAC acknowledgements are required for 11018 * MPDUs/A-MSDUs belonging to this TS and the form of those acknowledgements. 11019 * Possible values are defined in enum qca_wlan_tspec_ack_policy. 11020 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11021 * 11022 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE: 11023 * u16 attribute. Specify the nominal size in bytes of MSDUs/A-MSDUs 11024 * belonging to this TS. 11025 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11026 * 11027 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE: 11028 * u16 attribute. Specify the maximum size in bytes of MSDUs/A-MSDUs 11029 * belonging to this TS. 11030 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11031 * 11032 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL: 11033 * u32 attribute. Specify the minimum interval in microseconds between the 11034 * start of two successive SPs. 11035 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11036 * 11037 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL: 11038 * u32 attribute. Specify the maximum interval in microseconds between the 11039 * start of two successive SPs. 11040 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11041 * 11042 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL: 11043 * u32 attribute. Specify the minimum interval in microseconds that can elapse 11044 * without arrival or transfer of an MPDU belonging to the TS before this TS 11045 * is deleted by the MAC entity at the HC. 11046 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11047 * 11048 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL: 11049 * u32 attribute. Specify the minimum interval in microseconds that can elapse 11050 * without arrival or transfer of an MSDU belonging to the TS before the 11051 * generation of successive QoS(+)CF-Poll is stopped for this TS. A value of 11052 * 0xFFFFFFFF disables the suspension interval. The value of the suspension 11053 * interval is always less than or equal to the inactivity interval. 11054 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11055 * 11056 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE: 11057 * u32 attribute. Indicate the lowest data rate in bps specified at the MAC 11058 * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the 11059 * bounds of this TSPEC. 11060 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11061 * 11062 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE: 11063 * u32 attribute. Indicate the average data rate in bps specified at the MAC 11064 * SAP for transport of MSDUs or A-MSDUs belonging to this TS within the 11065 * bounds of this TSPEC. 11066 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11067 * 11068 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE: 11069 * u32 attribute. Indicate the maximum allowable data rate in bps specified at 11070 * the MAC SAP for transport of MSDUs or A-MSDUs belonging to this TS within 11071 * the bounds of this TSPEC. 11072 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11073 * 11074 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE: 11075 * u32 attribute. Specify the maximum burst size in bytes of the MSDUs/A-MSDUs 11076 * belonging to this TS that arrive at the MAC SAP at the peak data rate. A 11077 * value of 0 indicates that there are no bursts. 11078 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11079 * 11080 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE: 11081 * u32 attribute. Indicate the minimum PHY rate in bps for transport of 11082 * MSDUs/A-MSDUs belonging to this TS within the bounds of this TSPEC. 11083 * Applicable for operation: QCA_WLAN_TSPEC_ADD. An optional attribute. 11084 * 11085 * @QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE: 11086 * u16 attribute. Specify the excess allocation of time (and bandwidth) over 11087 * and above the stated application rates required to transport an MSDU/A-MSDU 11088 * belonging to the TS in this TSPEC. 11089 * Applicable for operation: QCA_WLAN_TSPEC_ADD. A mandatory attribute. 11090 */ 11091 enum qca_wlan_vendor_attr_config_tspec { 11092 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INVALID = 0, 11093 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_OPERATION = 1, 11094 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_TSID = 2, 11095 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_DIRECTION = 3, 11096 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_APSD = 4, 11097 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_USER_PRIORITY = 5, 11098 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_ACK_POLICY = 6, 11099 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_NOMINAL_MSDU_SIZE = 7, 11100 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAXIMUM_MSDU_SIZE = 8, 11101 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MIN_SERVICE_INTERVAL = 9, 11102 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX_SERVICE_INTERVAL = 10, 11103 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_INACTIVITY_INTERVAL = 11, 11104 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SUSPENSION_INTERVAL = 12, 11105 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_DATA_RATE = 13, 11106 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MEAN_DATA_RATE = 14, 11107 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_PEAK_DATA_RATE = 15, 11108 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_BURST_SIZE = 16, 11109 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MINIMUM_PHY_RATE = 17, 11110 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_SURPLUS_BANDWIDTH_ALLOWANCE = 18, 11111 11112 /* keep last */ 11113 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST, 11114 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_MAX = 11115 QCA_WLAN_VENDOR_ATTR_CONFIG_TSPEC_AFTER_LAST - 1, 11116 }; 11117 11118 /** 11119 * enum qca_wlan_vendor_oci_override_frame_type - OCI override frame type 11120 * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ: SA Query Request frame 11121 * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP: SA Query Response frame 11122 * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ: FT Reassociation Request 11123 * frame 11124 * @QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ: FILS Reassociation 11125 * Request frame. 11126 */ 11127 enum qca_wlan_vendor_oci_override_frame_type { 11128 QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_REQ = 1, 11129 QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_SA_QUERY_RESP = 2, 11130 QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FT_REASSOC_REQ = 3, 11131 QCA_WLAN_VENDOR_OCI_OVERRIDE_FRAME_FILS_REASSOC_REQ = 4, 11132 }; 11133 11134 /** 11135 * enum qca_wlan_vendor_attr_oci_override: Represents attributes for 11136 * OCI override request. These attributes are used inside nested attribute 11137 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OCI_OVERRIDE in QCA vendor command 11138 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 11139 * 11140 * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE: Required attribute, u8. 11141 * Values from enum qca_wlan_vendor_oci_override_frame_type used in this 11142 * attribute to specify the frame type in which the OCI is to be overridden. 11143 * 11144 * @QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY: Required (u32) 11145 * OCI frequency (in MHz) to override in the specified frame type. 11146 */ 11147 enum qca_wlan_vendor_attr_oci_override { 11148 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_INVALID = 0, 11149 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FRAME_TYPE = 1, 11150 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_FREQUENCY = 2, 11151 11152 /* keep last */ 11153 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST, 11154 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_MAX = 11155 QCA_WLAN_VENDOR_ATTR_OCI_OVERRIDE_AFTER_LAST - 1, 11156 }; 11157 11158 /** 11159 * enum qca_wlan_medium_assess_type - Type of medium assess request 11160 * 11161 * Values for %QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE. 11162 */ 11163 enum qca_wlan_medium_assess_type { 11164 QCA_WLAN_MEDIUM_ASSESS_CCA = 0, 11165 QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT = 1, 11166 }; 11167 11168 /** 11169 * enum qca_wlan_vendor_attr_medium_assess - Attributes used by 11170 * %QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS vendor command. 11171 * 11172 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE: 11173 * u8 attribute. Mandatory in all kinds of medium assess requests/responses. 11174 * Specify the type of medium assess request and indicate its type in response. 11175 * Possible values are defined in enum qca_wlan_medium_assess_type. 11176 * 11177 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD: 11178 * u32 attribute. Mandatory in CCA request. 11179 * Specify the assessment period in terms of seconds. Assessment result will be 11180 * sent as the response to the CCA request after the assessment period. 11181 * 11182 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT: 11183 * u32 attribute. Mandatory in response to CCA request. 11184 * Total timer tick count of the assessment cycle. 11185 * 11186 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT: 11187 * u32 attribute. Mandatory in response to CCA request. 11188 * Timer tick count of idle time in the assessment cycle. 11189 * 11190 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT: 11191 * u32 attribute. Mandatory in response to CCA request. 11192 * Timer tick count of Intra BSS traffic RX time in the assessment cycle. 11193 * 11194 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT: 11195 * u32 attribute. Mandatory in response to CCA request. 11196 * Timer tick count of Overlapping BSS traffic RX time in the assessment cycle. 11197 * 11198 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI: 11199 * s32 attribute. Mandatory in response to CCA request. 11200 * Maximum RSSI of Intra BSS traffic in the assessment cycle. 11201 * 11202 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI: 11203 * s32 attribute. Mandatory in response to CCA request. 11204 * Minimum RSSI of Intra BSS traffic in the assessment cycle. 11205 * 11206 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE: 11207 * u8 attribute. Mandatory in congestion report request. 11208 * 1-enable 0-disable. 11209 * 11210 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD: 11211 * u8 attribute. Mandatory in congestion report enable request and will be 11212 * ignored if present in congestion report disable request. Possible values are 11213 * 0-100. A vendor event QCA_NL80211_VENDOR_SUBCMD_MEDIUM_ASSESS with the type 11214 * QCA_WLAN_MEDIUM_ASSESS_CONGESTION_REPORT will be sent to userspace if 11215 * congestion percentage reaches the configured threshold. 11216 * 11217 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL: 11218 * u8 attribute. Optional in congestion report enable request and will be 11219 * ignored if present in congestion report disable request. 11220 * Specify the interval of congestion report event in terms of seconds. Possible 11221 * values are 1-255. Default value 1 will be used if this attribute is omitted 11222 * or using invalid values. 11223 * 11224 * @QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE: 11225 * u8 attribute. Mandatory in congestion report event. 11226 * Indicate the actual congestion percentage. Possible values are 0-100. 11227 */ 11228 enum qca_wlan_vendor_attr_medium_assess { 11229 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_INVALID = 0, 11230 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TYPE = 1, 11231 11232 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_PERIOD = 2, 11233 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_TOTAL_CYCLE_COUNT = 3, 11234 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IDLE_COUNT = 4, 11235 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_IBSS_RX_COUNT = 5, 11236 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_OBSS_RX_COUNT = 6, 11237 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX_IBSS_RSSI = 7, 11238 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MIN_IBSS_RSSI = 8, 11239 11240 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_ENABLE = 9, 11241 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_THRESHOLD = 10, 11242 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_REPORT_INTERVAL = 11, 11243 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_CONGESTION_PERCENTAGE = 12, 11244 11245 /* keep last */ 11246 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST, 11247 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_MAX = 11248 QCA_WLAN_VENDOR_ATTR_MEDIUM_ASSESS_AFTER_LAST - 1, 11249 }; 11250 11251 /** 11252 * enum qca_wlan_vendor_attr_mbssid_tx_vdev_status - Defines attributes 11253 * used by QCA_NL80211_VENDOR_SUBCMD_MBSSID_TX_VDEV_STATUS vendor command. 11254 * 11255 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL: 11256 * u8 attribute. Notify the TX VDEV status. Possible values 0, 1 11257 * belonging to MBSSID/EMA_AP configuration. 0 means Non-Tx VDEV, 11258 * 1 means Tx VDEV. Mandatory attribute for all MBSSID VDEV status events. 11259 * 11260 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT: 11261 * u8 attribute, required. 1 means Tx VDEV up event. 0 means Tx VDEV down event. 11262 * 11263 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID: 11264 * u8 attribute, required. Indicates group id of Tx VDEV. 11265 * 11266 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO: 11267 * Nested attribute. This attribute shall be used by the driver to send 11268 * group information. The attributes defined in enum 11269 * qca_wlan_vendor_attr_mbssid_tx_vdev_group_info 11270 * are nested in this attribute. 11271 */ 11272 enum qca_wlan_vendor_attr_mbssid_tx_vdev_status { 11273 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_INVALID = 0, 11274 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_VAL = 1, 11275 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_EVENT = 2, 11276 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_ID = 3, 11277 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO = 4, 11278 11279 /* keep last */ 11280 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST, 11281 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_MAX = 11282 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_STATUS_AFTER_LAST - 1, 11283 }; 11284 11285 /** 11286 * enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info - Attributes used 11287 * inside %QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO nested attribute. 11288 * 11289 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX: 11290 * u32 attribute, required. Contains interface index. 11291 * 11292 * @QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS: 11293 * u8 attribute, required. 0 - means vdev is in down state. 11294 * 1 - means vdev is in up state. 11295 */ 11296 enum qca_wlan_vendor_attr_mbssid_tx_vdev_group_info { 11297 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_INVALID = 0, 11298 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_IF_INDEX = 1, 11299 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_STATUS = 2, 11300 11301 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_AFTER_LAST, 11302 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO_MAX = 11303 QCA_WLAN_VENDOR_ATTR_MBSSID_TX_VDEV_GROUP_INFO - 1, 11304 }; 11305 11306 /** 11307 * enum qca_wlan_concurrent_sta_policy_config - Concurrent STA policies 11308 * 11309 * @QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY: Preference to the primary 11310 * STA interface has to be given while selecting the connection policies 11311 * (e.g., BSSID, band, TX/RX chains, etc.) for the subsequent STA interface. 11312 * An interface is set as primary through the attribute 11313 * QCA_WLAN_VENDOR_ATTR_CONFIG_CONCURRENT_STA_PRIMARY. This policy is not 11314 * applicable if the primary interface has not been set earlier. 11315 * 11316 * The intention is not to downgrade the primary STA performance, such as: 11317 * - Do not reduce the number of TX/RX chains of primary connection. 11318 * - Do not optimize DBS vs. MCC/SCC, if DBS ends up reducing the number of 11319 * chains. 11320 * - If using MCC, should set the MCC duty cycle of the primary connection to 11321 * be higher than the secondary connection. 11322 * 11323 * @QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED: The connection policies for the 11324 * subsequent STA connection shall be chosen to balance with the existing 11325 * concurrent STA's performance. 11326 * Such as 11327 * - Can choose MCC or DBS mode depending on the MCC efficiency and hardware 11328 * capability. 11329 * - If using MCC, set the MCC duty cycle of the primary connection to be equal 11330 * to the secondary. 11331 * - Prefer BSSID candidates which will help provide the best "overall" 11332 * performance for all the STA connections. 11333 */ 11334 enum qca_wlan_concurrent_sta_policy_config { 11335 QCA_WLAN_CONCURRENT_STA_POLICY_PREFER_PRIMARY = 0, 11336 QCA_WLAN_CONCURRENT_STA_POLICY_UNBIASED = 1, 11337 }; 11338 11339 /** 11340 * enum qca_wlan_vendor_attr_concurrent_sta_policy - Defines attributes 11341 * used by QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY vendor command. 11342 * 11343 * @QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_CONFIG: 11344 * u8 attribute. Configures the concurrent STA policy configuration. 11345 * Possible values are defined in enum qca_wlan_concurrent_sta_policy_config. 11346 */ 11347 enum qca_wlan_vendor_attr_concurrent_sta_policy { 11348 QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_INVALID = 0, 11349 QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_CONFIG = 1, 11350 11351 /* keep last */ 11352 QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_AFTER_LAST, 11353 QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_MAX = 11354 QCA_WLAN_VENDOR_ATTR_CONCURRENT_STA_POLICY_AFTER_LAST - 1, 11355 11356 }; 11357 11358 /** 11359 * enum qca_sta_connect_fail_reason_codes - Defines values carried 11360 * by QCA_WLAN_VENDOR_ATTR_GET_STA_INFO_CONNECT_FAIL_REASON_CODE vendor 11361 * attribute. 11362 * @QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND: No Probe Response frame received 11363 * for unicast Probe Request frame. 11364 * @QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL: STA failed to send auth request. 11365 * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED: AP didn't send ACK for 11366 * auth request. 11367 * @QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED: Auth response is not 11368 * received from AP. 11369 * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL: STA failed to send 11370 * Association Request frame. 11371 * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED: AP didn't send ACK for 11372 * Association Request frame. 11373 * @QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED: Association Response 11374 * frame is not received from AP. 11375 */ 11376 enum qca_sta_connect_fail_reason_codes { 11377 QCA_STA_CONNECT_FAIL_REASON_NO_BSS_FOUND = 1, 11378 QCA_STA_CONNECT_FAIL_REASON_AUTH_TX_FAIL = 2, 11379 QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_ACK_RECEIVED = 3, 11380 QCA_STA_CONNECT_FAIL_REASON_AUTH_NO_RESP_RECEIVED = 4, 11381 QCA_STA_CONNECT_FAIL_REASON_ASSOC_REQ_TX_FAIL = 5, 11382 QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_ACK_RECEIVED = 6, 11383 QCA_STA_CONNECT_FAIL_REASON_ASSOC_NO_RESP_RECEIVED = 7, 11384 }; 11385 11386 /** 11387 * enum qca_wlan_vendor_usable_channels_filter - Bitmask of different 11388 * filters defined in this enum are used in attribute 11389 * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK. 11390 * 11391 * @QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX: When this bit is set, the driver 11392 * shall filter the channels which are not usable because of coexistence with 11393 * cellular radio. 11394 * @QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY: When this bit is set, the driver 11395 * shall filter the channels which are not usable because of existing active 11396 * interfaces in the driver and will result in Multi Channel Concurrency, etc. 11397 * 11398 */ 11399 enum qca_wlan_vendor_usable_channels_filter { 11400 QCA_WLAN_VENDOR_FILTER_CELLULAR_COEX = 0, 11401 QCA_WLAN_VENDOR_FILTER_WLAN_CONCURRENCY = 1, 11402 }; 11403 11404 /** 11405 * enum qca_wlan_vendor_attr_chan_info - Attributes used inside 11406 * %QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO nested attribute. 11407 * 11408 * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ: 11409 * u32 attribute, required. Indicates the center frequency of the primary 11410 * channel in MHz. 11411 * 11412 * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ: 11413 * u32 attribute. Indicates the center frequency of the primary segment of the 11414 * channel in MHz. This attribute is required when reporting 40 MHz, 80 MHz, 11415 * 160 MHz, and 320 MHz channels. 11416 * 11417 * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ: 11418 * u32 attribute. Indicates the center frequency of the secondary segment of 11419 * 80+80 channel in MHz. This attribute is required only when 11420 * QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH is set to NL80211_CHAN_WIDTH_80P80. 11421 * 11422 * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH: 11423 * u32 attribute, required. Indicates the bandwidth of the channel, possible 11424 * values are defined in enum nl80211_chan_width. 11425 * 11426 * @QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK: 11427 * u32 attribute, required. Indicates all the interface types for which this 11428 * channel is usable. This attribute encapsulates bitmasks of interface types 11429 * defined in enum nl80211_iftype. 11430 * 11431 */ 11432 enum qca_wlan_vendor_attr_chan_info { 11433 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_INVALID = 0, 11434 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_PRIMARY_FREQ = 1, 11435 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG0_FREQ = 2, 11436 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_SEG1_FREQ = 3, 11437 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_BANDWIDTH = 4, 11438 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_IFACE_MODE_MASK = 5, 11439 11440 /* keep last */ 11441 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST, 11442 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_MAX = 11443 QCA_WLAN_VENDOR_ATTR_CHAN_INFO_AFTER_LAST - 1, 11444 }; 11445 11446 /** 11447 * enum qca_wlan_vendor_attr_usable_channels - Attributes used by 11448 * %QCA_NL80211_VENDOR_SUBCMD_USABLE_CHANNELS vendor command. 11449 * 11450 * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK: 11451 * u32 attribute. Indicates the bands from which the channels should be reported 11452 * in response. This attribute encapsulates bit masks of bands defined in enum 11453 * nl80211_band. Optional attribute, if not present in the request the driver 11454 * shall return channels from all supported bands. 11455 * 11456 * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK: 11457 * u32 attribute. Indicates all the interface types for which the usable 11458 * channels information is requested. This attribute encapsulates bitmasks of 11459 * interface types defined in enum nl80211_iftype. Optional attribute, if not 11460 * present in the request the driver shall send information of all supported 11461 * interface modes. 11462 * 11463 * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK: 11464 * u32 attribute. This attribute carries information of all filters that shall 11465 * be applied while populating usable channels information by the driver. This 11466 * attribute carries bit masks of different filters defined in enum 11467 * qca_wlan_vendor_usable_channels_filter. Optional attribute, if not present 11468 * in the request the driver shall send information of channels without applying 11469 * any of the filters that can be configured through this attribute. 11470 * 11471 * @QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO: 11472 * Nested attribute. This attribute shall be used by the driver to send 11473 * usability information of each channel. The attributes defined in enum 11474 * qca_wlan_vendor_attr_chan_info are used inside this attribute. 11475 */ 11476 enum qca_wlan_vendor_attr_usable_channels { 11477 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_INVALID = 0, 11478 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_BAND_MASK = 1, 11479 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_IFACE_MODE_MASK = 2, 11480 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_FILTER_MASK = 3, 11481 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_CHAN_INFO = 4, 11482 11483 /* keep last */ 11484 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST, 11485 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_MAX = 11486 QCA_WLAN_VENDOR_ATTR_USABLE_CHANNELS_AFTER_LAST - 1, 11487 }; 11488 11489 /** 11490 * enum qca_wlan_vendor_attr_radar_history: Used by the vendor command 11491 * QCA_NL80211_VENDOR_SUBCMD_GET_RADAR_HISTORY to get DFS radar history. 11492 * 11493 * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES: Nested attribute to carry 11494 * the list of radar history entries. 11495 * Each entry contains freq, timestamp, and radar signal detect flag. 11496 * The driver shall add an entry when CAC has finished, or radar signal 11497 * has been detected post AP beaconing. The driver shall maintain at least 11498 * 8 entries in order to save CAC result for a 160 MHz channel. 11499 * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ: u32 attribute. 11500 * Channel frequency in MHz. 11501 * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP: u64 nanoseconds. 11502 * CLOCK_BOOTTIME timestamp when this entry is updated due to CAC 11503 * or radar detection. 11504 * @QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED: NLA_FLAG attribute. 11505 * This flag indicates radar signal has been detected. 11506 */ 11507 enum qca_wlan_vendor_attr_radar_history { 11508 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_INVALID = 0, 11509 11510 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_ENTRIES = 1, 11511 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_FREQ = 2, 11512 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_TIMESTAMP = 3, 11513 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_DETECTED = 4, 11514 11515 /* keep last */ 11516 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST, 11517 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_MAX = 11518 QCA_WLAN_VENDOR_ATTR_RADAR_HISTORY_LAST - 1, 11519 }; 11520 11521 /** 11522 * enum qca_wlan_vendor_attr_mdns_offload - Attributes used by 11523 * %QCA_NL80211_VENDOR_SUBCMD_MDNS_OFFLOAD vendor command. 11524 * 11525 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE: Required (flag) 11526 * Enable mDNS offload. This attribute is mandatory to enable 11527 * mDNS offload feature. If this attribute is not present, mDNS offload 11528 * is disabled. 11529 * 11530 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE: Nested attribute containing 11531 * one or more %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY attributes. This 11532 * attribute is mandatory when enabling the feature, and not required when 11533 * disabling the feature. 11534 * 11535 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY: Nested attribute containing 11536 * the following attributes: 11537 * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN 11538 * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT 11539 * %QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD 11540 * 11541 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN: Required string attribute. 11542 * It consists of a hostname and ".local" as the domain name. The character 11543 * set is limited to UTF-8 encoding. The maximum allowed size is 63 bytes. 11544 * It is used to compare the domain in the "QU" query. Only 1 FQDN is 11545 * supported per vdev. 11546 * For example: myphone.local 11547 * 11548 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT: Required 11549 * u16 attribute. It specifies the total number of resource records present 11550 * in the answer section of the answer payload. This attribute is needed by the 11551 * firmware to populate the mDNS response frame for mDNS queries without having 11552 * to parse the answer payload. 11553 * 11554 * @QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD: Required binary blob 11555 * attribute sent by the mdnsResponder from userspace. It contains resource 11556 * records of various types (e.g., A, AAAA, PTR, TXT) and service list. This 11557 * payload is passed down to the firmware and is transmitted in response to 11558 * mDNS queries. 11559 * The maximum supported size of the answer payload is 512 bytes. 11560 */ 11561 enum qca_wlan_vendor_attr_mdns_offload { 11562 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_INVALID = 0, 11563 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENABLE = 1, 11564 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_TABLE = 2, 11565 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ENTRY = 3, 11566 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_FQDN = 4, 11567 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_RESOURCE_RECORDS_COUNT = 5, 11568 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_ANSWER_PAYLOAD = 6, 11569 11570 /* keep last */ 11571 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST, 11572 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_MAX = 11573 QCA_WLAN_VENDOR_ATTR_MDNS_OFFLOAD_AFTER_LAST - 1, 11574 }; 11575 11576 /** 11577 * qca_wlan_vendor_monitor_data_frame_type - Represent the various 11578 * Data frame types to be sent over the monitor interface. 11579 */ 11580 enum qca_wlan_vendor_monitor_data_frame_type { 11581 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL = BIT(0), 11582 /* valid only if QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ALL is not set 11583 */ 11584 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ARP = BIT(1), 11585 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV4 = BIT(2), 11586 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DHCPV6 = BIT(3), 11587 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_EAPOL = BIT(4), 11588 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV4 = BIT(5), 11589 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_DNSV6 = BIT(6), 11590 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYN = BIT(7), 11591 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_SYNACK = BIT(8), 11592 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FIN = BIT(9), 11593 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_FINACK = BIT(10), 11594 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_ACK = BIT(11), 11595 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_TCP_RST = BIT(12), 11596 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV4 = BIT(13), 11597 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_ICMPV6 = BIT(14), 11598 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_RTP = BIT(15), 11599 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_TYPE_SIP = BIT(16), 11600 QCA_WLAN_VENDOR_MONITOR_DATA_FRAME_QOS_NULL = BIT(17), 11601 }; 11602 11603 /** 11604 * qca_wlan_vendor_monitor_mgmt_frame_type - Represent the various 11605 * Management frame types to be sent over the monitor interface. 11606 * @QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL: All the Management Frames. 11607 * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_NO_BEACON: All the Management frames 11608 * except the Beacon frame. 11609 * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON: Only the connected 11610 * BSSID Beacon frames. Valid only in the connected state. 11611 * @QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON: Represents 11612 * the Beacon frames obtained during the scan (off channel and connected 11613 * channel), when in connected state. 11614 */ 11615 11616 enum qca_wlan_vendor_monitor_mgmt_frame_type { 11617 QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL = BIT(0), 11618 /* valid only if QCA_WLAN_VENDOR_MONITOR_MGMT_FRAME_TYPE_ALL is not set 11619 */ 11620 QCA_WLAN_VENDOR_MONITOR_MGMT_NO_BEACON = BIT(1), 11621 QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_BEACON = BIT(2), 11622 QCA_WLAN_VENDOR_MONITOR_MGMT_CONNECT_SCAN_BEACON = BIT(3), 11623 }; 11624 11625 /** 11626 * qca_wlan_vendor_monitor_ctrl_frame_type - Represent the various 11627 * Control frame types to be sent over the monitor interface. 11628 * @QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL: All the Control frames 11629 * @QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME: Trigger frame 11630 */ 11631 enum qca_wlan_vendor_monitor_ctrl_frame_type { 11632 QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL = BIT(0), 11633 /* valid only if QCA_WLAN_VENDOR_MONITOR_CTRL_FRAME_TYPE_ALL is not set 11634 */ 11635 QCA_WLAN_VENDOR_MONITOR_CTRL_TRIGGER_FRAME = BIT(1), 11636 }; 11637 11638 /** 11639 * enum qca_wlan_vendor_attr_set_monitor_mode - Used by the 11640 * vendor command QCA_NL80211_VENDOR_SUBCMD_SET_MONITOR_MODE to set the 11641 * monitor mode. 11642 * 11643 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE: u32 attribute. 11644 * Represents the TX Data frame types to be monitored (u32). These Data frames 11645 * are represented by enum qca_wlan_vendor_monitor_data_frame_type. 11646 * 11647 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE: u32 attribute. 11648 * Represents the RX Data frame types to be monitored (u32). These Data frames 11649 * are represented by enum qca_wlan_vendor_monitor_data_frame_type. 11650 * 11651 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE: u32 attribute. 11652 * Represents the TX Management frame types to be monitored (u32). These 11653 * Management frames are represented by 11654 * enum qca_wlan_vendor_monitor_mgmt_frame_type. 11655 * 11656 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE: u32 attribute. 11657 * Represents the RX Management frame types to be monitored (u32). These 11658 * Management frames are represented by 11659 * enum qca_wlan_vendor_monitor_mgmt_frame_type. 11660 * 11661 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE: u32 attribute. 11662 * Represents the TX Control frame types to be monitored (u32). These Control 11663 * frames are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. 11664 * 11665 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE: u32 attribute. 11666 * Represents the RX Control frame types to be monitored (u32). These Control 11667 * frames are represented by enum qca_wlan_vendor_monitor_ctrl_frame_type. 11668 * 11669 * @QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL: u32 11670 * attribute. 11671 * Represents the interval in milliseconds only for the connected Beacon frames, 11672 * expecting the connected BSS's Beacon frames to be sent on the monitor 11673 * interface at this specific interval. 11674 */ 11675 enum qca_wlan_vendor_attr_set_monitor_mode 11676 { 11677 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_INVALID = 0, 11678 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_TX_FRAME_TYPE = 1, 11679 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_DATA_RX_FRAME_TYPE = 2, 11680 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_TX_FRAME_TYPE = 3, 11681 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MGMT_RX_FRAME_TYPE = 4, 11682 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_TX_FRAME_TYPE = 5, 11683 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CTRL_RX_FRAME_TYPE = 6, 11684 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_CONNECTED_BEACON_INTERVAL = 7, 11685 11686 /* keep last */ 11687 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST, 11688 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_MAX = 11689 QCA_WLAN_VENDOR_ATTR_SET_MONITOR_MODE_AFTER_LAST - 1, 11690 }; 11691 11692 /** 11693 * enum qca_wlan_vendor_roam_scan_state - Roam scan state flags. 11694 * Bits will be set to 1 if the corresponding state is enabled. 11695 * 11696 * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_START: Scan Start. 11697 * @QCA_VENDOR_WLAN_ROAM_SCAN_STATE_END: Scan end. 11698 */ 11699 enum qca_wlan_vendor_roam_scan_state { 11700 QCA_WLAN_VENDOR_ROAM_SCAN_STATE_START = BIT(0), 11701 QCA_WLAN_VENDOR_ROAM_SCAN_STATE_END = BIT(1), 11702 }; 11703 11704 /** 11705 * enum qca_wlan_vendor_roam_event_type - Roam event type flags. 11706 * Bits will be set to 1 if the corresponding event is notified. 11707 * 11708 * @QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON: Represents that the roam event 11709 * carries the trigger reason. When set, it is expected that the roam event 11710 * carries the respective reason via the attribute 11711 * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON. This event also carries 11712 * the BSSID, RSSI, frequency info of the AP to which the roam is attempted. 11713 * 11714 * @QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON: Represents that the roam event 11715 * carries the roam fail reason. When set, it is expected that the roam event 11716 * carries the respective reason via the attribute 11717 * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_FAIL_REASON. This event also carries the 11718 * BSSID, RSSI, frequency info of the AP to which the roam was attempted. 11719 * 11720 * @QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON: Represents that the roam 11721 * event carries the roam invoke fail reason. When set, it is expected that 11722 * the roam event carries the respective reason via the attribute 11723 * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON. 11724 * 11725 * @QCA_WLAN_VENDOR_ROAM_EVENT_SCAN_STATE: Represents that the roam event 11726 * carries the roam scan state. When set, it is expected that the roam event 11727 * carries the respective scan state via the attribute 11728 * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE and the corresponding 11729 * frequency info via QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST. 11730 */ 11731 enum qca_wlan_vendor_roam_event_type { 11732 QCA_WLAN_VENDOR_ROAM_EVENT_TRIGGER_REASON = BIT(0), 11733 QCA_WLAN_VENDOR_ROAM_EVENT_FAIL_REASON = BIT(1), 11734 QCA_WLAN_VENDOR_ROAM_EVENT_INVOKE_FAIL_REASON = BIT(2), 11735 QCA_WLAN_VENDOR_ROAM_EVENT_ROAM_SCAN_STATE = BIT(3), 11736 }; 11737 11738 /** 11739 * enum qca_wlan_vendor_attr_roam_events_candidate_info: Roam candidate info. 11740 * Referred by QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO. 11741 * 11742 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID: 6-byte MAC address 11743 * representing the BSSID of the AP to which the roam is attempted. 11744 * 11745 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI: Signed 32-bit value 11746 * in dBm, signifying the RSSI of the candidate BSSID to which the Roaming is 11747 * attempted. 11748 * 11749 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ: u32, frequency in MHz 11750 * on which the roam is attempted. 11751 * 11752 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON: u32, used in 11753 * STA mode only. This represents the roam fail reason for the last failed 11754 * roaming attempt by the firmware for the specific BSSID. Different roam 11755 * failure reason codes are specified in enum qca_vendor_roam_fail_reasons. 11756 */ 11757 enum qca_wlan_vendor_attr_roam_events_candidate_info { 11758 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_INVALID = 0, 11759 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_BSSID = 1, 11760 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_RSSI = 2, 11761 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FREQ = 3, 11762 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_FAIL_REASON = 4, 11763 11764 /* keep last */ 11765 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST, 11766 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_MAX = 11767 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO_AFTER_LAST - 1, 11768 }; 11769 11770 /** 11771 * enum qca_wlan_vendor_attr_roam_events - Used by the 11772 * vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS to either configure the 11773 * roam events to the driver or notify these events from the driver. 11774 * 11775 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE: u8 attribute. Configures the 11776 * driver/firmware to enable/disable the notification of roam events. It's a 11777 * mandatory attribute and used only in the request from the userspace to the 11778 * host driver. 1-Enable, 0-Disable. 11779 * If the roaming is totally offloaded to the firmware, this request when 11780 * enabled shall mandate the firmware to notify all the relevant roam events 11781 * represented by the below attributes. If the host is in the suspend mode, 11782 * the behavior of the firmware to notify these events is guided by 11783 * QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_DEVICE_STATE, and if the request is to get 11784 * these events in the suspend state, the firmware is expected to wake up the 11785 * host before the respective events are notified. Please note that such a 11786 * request to get the events in the suspend state will have a definite power 11787 * implication. 11788 * 11789 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE: flag attribute. Represents 11790 * that the roam events need to be notified in the suspend state too. By 11791 * default, these roam events are notified in the resume state. With this flag, 11792 * the roam events are notified in both resume and suspend states. 11793 * This attribute is used in the request from the userspace to the host driver. 11794 * 11795 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE: u32, used in STA mode only. 11796 * Represents the different roam event types, signified by the enum 11797 * qca_wlan_vendor_roam_event_type. 11798 * Each bit of this attribute represents the different roam even types reported 11799 * through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11800 * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11801 * 11802 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON: u32, used in STA 11803 * mode only. This represents the roam trigger reason for the last roaming 11804 * attempted by the firmware. Each bit of this attribute represents the 11805 * different roam trigger reason code which are defined in enum 11806 * qca_vendor_roam_triggers. 11807 * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11808 * 11809 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON: u32, used in 11810 * STA mode only. This represents the roam invoke fail reason for the last 11811 * failed roam invoke. Different roam invoke failure reason codes 11812 * are specified in enum qca_vendor_roam_invoke_fail_reasons. 11813 * 11814 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO: Array of candidates info 11815 * for which the roam is attempted. Each entry is a nested attribute defined 11816 * by enum qca_wlan_vendor_attr_roam_events_candidate_info. 11817 * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11818 * 11819 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE: u8 attribute. Represents 11820 * the scan state on which the roam events need to be notified. The values for 11821 * this attribute are referred from enum qca_wlan_vendor_roam_scan_state. 11822 * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11823 * 11824 * @QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST: Nested attribute of 11825 * u32 values. List of frequencies in MHz considered for a roam scan. 11826 * This is sent as an event through QCA_NL80211_VENDOR_SUBCMD_ROAM_EVENTS. 11827 */ 11828 11829 enum qca_wlan_vendor_attr_roam_events 11830 { 11831 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVALID = 0, 11832 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CONFIGURE = 1, 11833 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_SUSPEND_STATE = 2, 11834 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TYPE = 3, 11835 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_TRIGGER_REASON = 4, 11836 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_INVOKE_FAIL_REASON = 5, 11837 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_CANDIDATE_INFO = 6, 11838 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_STATE = 7, 11839 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_ROAM_SCAN_FREQ_LIST = 8, 11840 11841 /* keep last */ 11842 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST, 11843 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_MAX = 11844 QCA_WLAN_VENDOR_ATTR_ROAM_EVENTS_AFTER_LAST -1, 11845 }; 11846 11847 #endif /* QCA_VENDOR_H */ 11848