1ChangeLog for hostapd 2 32016-10-02 - v2.6 4 * fixed EAP-pwd last fragment validation 5 [http://w1.fi/security/2015-7/] (CVE-2015-5314) 6 * fixed WPS configuration update vulnerability with malformed passphrase 7 [http://w1.fi/security/2016-1/] (CVE-2016-4476) 8 * extended channel switch support for VHT bandwidth changes 9 * added support for configuring new ANQP-elements with 10 anqp_elem=<InfoID>:<hexdump of payload> 11 * fixed Suite B 192-bit AKM to use proper PMK length 12 (note: this makes old releases incompatible with the fixed behavior) 13 * added no_probe_resp_if_max_sta=1 parameter to disable Probe Response 14 frame sending for not-associated STAs if max_num_sta limit has been 15 reached 16 * added option (-S as command line argument) to request all interfaces 17 to be started at the same time 18 * modified rts_threshold and fragm_threshold configuration parameters 19 to allow -1 to be used to disable RTS/fragmentation 20 * EAP-pwd: added support for Brainpool Elliptic Curves 21 (with OpenSSL 1.0.2 and newer) 22 * fixed EAPOL reauthentication after FT protocol run 23 * fixed FTIE generation for 4-way handshake after FT protocol run 24 * fixed and improved various FST operations 25 * TLS server 26 - support SHA384 and SHA512 hashes 27 - support TLS v1.2 signature algorithm with SHA384 and SHA512 28 - support PKCS #5 v2.0 PBES2 29 - support PKCS #5 with PKCS #12 style key decryption 30 - minimal support for PKCS #12 31 - support OCSP stapling (including ocsp_multi) 32 * added support for OpenSSL 1.1 API changes 33 - drop support for OpenSSL 0.9.8 34 - drop support for OpenSSL 1.0.0 35 * EAP-PEAP: support fast-connect crypto binding 36 * RADIUS 37 - fix Called-Station-Id to not escape SSID 38 - add Event-Timestamp to all Accounting-Request packets 39 - add Acct-Session-Id to Accounting-On/Off 40 - add Acct-Multi-Session-Id ton Access-Request packets 41 - add Service-Type (= Frames) 42 - allow server to provide PSK instead of passphrase for WPA-PSK 43 Tunnel_password case 44 - update full message for interim accounting updates 45 - add Acct-Delay-Time into Accounting messages 46 - add require_message_authenticator configuration option to require 47 CoA/Disconnect-Request packets to be authenticated 48 * started to postpone WNM-Notification frame sending by 100 ms so that 49 the STA has some more time to configure the key before this frame is 50 received after the 4-way handshake 51 * VHT: added interoperability workaround for 80+80 and 160 MHz channels 52 * extended VLAN support (per-STA vif, etc.) 53 * fixed PMKID derivation with SAE 54 * nl80211 55 - added support for full station state operations 56 - fix IEEE 802.1X/WEP EAP reauthentication and rekeying to use 57 unencrypted EAPOL frames 58 * added initial MBO support; number of extensions to WNM BSS Transition 59 Management 60 * added initial functionality for location related operations 61 * added assocresp_elements parameter to allow vendor specific elements 62 to be added into (Re)Association Response frames 63 * improved Public Action frame addressing 64 - use Address 3 = wildcard BSSID in GAS response if a query from an 65 unassociated STA used that address 66 - fix TX status processing for Address 3 = wildcard BSSID 67 - add gas_address3 configuration parameter to control Address 3 68 behavior 69 * added command line parameter -i to override interface parameter in 70 hostapd.conf 71 * added command completion support to hostapd_cli 72 * added passive client taxonomy determination (CONFIG_TAXONOMY=y 73 compile option and "SIGNATURE <addr>" control interface command) 74 * number of small fixes 75 762015-09-27 - v2.5 77 * fixed WPS UPnP vulnerability with HTTP chunked transfer encoding 78 [http://w1.fi/security/2015-2/] (CVE-2015-4141) 79 * fixed WMM Action frame parser 80 [http://w1.fi/security/2015-3/] (CVE-2015-4142) 81 * fixed EAP-pwd server missing payload length validation 82 [http://w1.fi/security/2015-4/] 83 (CVE-2015-4143, CVE-2015-4144, CVE-2015-4145) 84 * fixed validation of WPS and P2P NFC NDEF record payload length 85 [http://w1.fi/security/2015-5/] 86 * nl80211: 87 - fixed vendor command handling to check OUI properly 88 * fixed hlr_auc_gw build with OpenSSL 89 * hlr_auc_gw: allow Milenage RES length to be reduced 90 * disable HT for a station that does not support WMM/QoS 91 * added support for hashed password (NtHash) in EAP-pwd server 92 * fixed and extended dynamic VLAN cases 93 * added EAP-EKE server support for deriving Session-Id 94 * set Acct-Session-Id to a random value to make it more likely to be 95 unique even if the device does not have a proper clock 96 * added more 2.4 GHz channels for 20/40 MHz HT co-ex scan 97 * modified SAE routines to be more robust and PWE generation to be 98 stronger against timing attacks 99 * added support for Brainpool Elliptic Curves with SAE 100 * increases maximum value accepted for cwmin/cwmax 101 * added support for CCMP-256 and GCMP-256 as group ciphers with FT 102 * added Fast Session Transfer (FST) module 103 * removed optional fields from RSNE when using FT with PMF 104 (workaround for interoperability issues with iOS 8.4) 105 * added EAP server support for TLS session resumption 106 * fixed key derivation for Suite B 192-bit AKM (this breaks 107 compatibility with the earlier version) 108 * added mechanism to track unconnected stations and do minimal band 109 steering 110 * number of small fixes 111 1122015-03-15 - v2.4 113 * allow OpenSSL cipher configuration to be set for internal EAP server 114 (openssl_ciphers parameter) 115 * fixed number of small issues based on hwsim test case failures and 116 static analyzer reports 117 * fixed Accounting-Request to not include duplicated Acct-Session-Id 118 * add support for Acct-Multi-Session-Id in RADIUS Accounting messages 119 * add support for PMKSA caching with SAE 120 * add support for generating BSS Load element (bss_load_update_period) 121 * fixed channel switch from VHT to HT 122 * add INTERFACE-ENABLED and INTERFACE-DISABLED ctrl_iface events 123 * add support for learning STA IPv4/IPv6 addresses and configuring 124 ProxyARP support 125 * dropped support for the madwifi driver interface 126 * add support for Suite B (128-bit and 192-bit level) key management and 127 cipher suites 128 * fixed a regression with driver=wired 129 * extend EAPOL-Key msg 1/4 retry workaround for changing SNonce 130 * add BSS_TM_REQ ctrl_iface command to send BSS Transition Management 131 Request frames and BSS-TM-RESP event to indicate response to such 132 frame 133 * add support for EAP Re-Authentication Protocol (ERP) 134 * fixed AP IE in EAPOL-Key 3/4 when both WPA and FT was enabled 135 * fixed a regression in HT 20/40 coex Action frame parsing 136 * set stdout to be line-buffered 137 * add support for vendor specific VHT extension to enable 256 QAM rates 138 (VHT-MCS 8 and 9) on 2.4 GHz band 139 * RADIUS DAS: 140 - extend Disconnect-Request processing to allow matching of multiple 141 sessions 142 - support Acct-Multi-Session-Id as an identifier 143 - allow PMKSA cache entry to be removed without association 144 * expire hostapd STA entry if kernel does not have a matching entry 145 * allow chanlist to be used to specify a subset of channels for ACS 146 * improve ACS behavior on 2.4 GHz band and allow channel bias to be 147 configured with acs_chan_bias parameter 148 * do not reply to a Probe Request frame that includes DSS Parameter Set 149 element in which the channel does not match the current operating 150 channel 151 * add UPDATE_BEACON ctrl_iface command; this can be used to force Beacon 152 frame contents to be updated and to start beaconing on an interface 153 that used start_disabled=1 154 * fixed some RADIUS server failover cases 155 1562014-10-09 - v2.3 157 * fixed number of minor issues identified in static analyzer warnings 158 * fixed DFS and channel switch operation for multi-BSS cases 159 * started to use constant time comparison for various password and hash 160 values to reduce possibility of any externally measurable timing 161 differences 162 * extended explicit clearing of freed memory and expired keys to avoid 163 keeping private data in memory longer than necessary 164 * added support for number of new RADIUS attributes from RFC 7268 165 (Mobility-Domain-Id, WLAN-HESSID, WLAN-Pairwise-Cipher, 166 WLAN-Group-Cipher, WLAN-AKM-Suite, WLAN-Group-Mgmt-Pairwise-Cipher) 167 * fixed GET_CONFIG wpa_pairwise_cipher value 168 * added code to clear bridge FDB entry on station disconnection 169 * fixed PMKSA cache timeout from Session-Timeout for WPA/WPA2 cases 170 * fixed OKC PMKSA cache entry fetch to avoid a possible infinite loop 171 in case the first entry does not match 172 * fixed hostapd_cli action script execution to use more robust mechanism 173 (CVE-2014-3686) 174 1752014-06-04 - v2.2 176 * fixed SAE confirm-before-commit validation to avoid a potential 177 segmentation fault in an unexpected message sequence that could be 178 triggered remotely 179 * extended VHT support 180 - Operating Mode Notification 181 - Power Constraint element (local_pwr_constraint) 182 - Spectrum management capability (spectrum_mgmt_required=1) 183 - fix VHT80 segment picking in ACS 184 - fix vht_capab 'Maximum A-MPDU Length Exponent' handling 185 - fix VHT20 186 * fixed HT40 co-ex scan for some pri/sec channel switches 187 * extended HT40 co-ex support to allow dynamic channel width changes 188 during the lifetime of the BSS 189 * fixed HT40 co-ex support to check for overlapping 20 MHz BSS 190 * fixed MSCHAP UTF-8 to UCS-2 conversion for three-byte encoding; 191 this fixes password with include UTF-8 characters that use 192 three-byte encoding EAP methods that use NtPasswordHash 193 * reverted TLS certificate validation step change in v2.1 that rejected 194 any AAA server certificate with id-kp-clientAuth even if 195 id-kp-serverAuth EKU was included 196 * fixed STA validation step for WPS ER commands to prevent a potential 197 crash if an ER sends an unexpected PutWLANResponse to a station that 198 is disassociated, but not fully removed 199 * enforce full EAP authentication after RADIUS Disconnect-Request by 200 removing the PMKSA cache entry 201 * added support for NAS-IP-Address, NAS-identifier, and NAS-IPv6-Address 202 in RADIUS Disconnect-Request 203 * added mechanism for removing addresses for MAC ACLs by prefixing an 204 entry with "-" 205 * Interworking/Hotspot 2.0 enhancements 206 - support Hotspot 2.0 Release 2 207 * OSEN network for online signup connection 208 * subscription remediation (based on RADIUS server request or 209 control interface HS20_WNM_NOTIF for testing purposes) 210 * Hotspot 2.0 release number indication in WFA RADIUS VSA 211 * deauthentication request (based on RADIUS server request or 212 control interface WNM_DEAUTH_REQ for testing purposes) 213 * Session Info URL RADIUS AVP to trigger ESS Disassociation Imminent 214 * hs20_icon config parameter to configure icon files for OSU 215 * osu_* config parameters for OSU Providers list 216 - do not use Interworking filtering rules on Probe Request if 217 Interworking is disabled to avoid interop issues 218 * added/fixed nl80211 functionality 219 - AP interface teardown optimization 220 - support vendor specific driver command 221 (VENDOR <vendor id> <sub command id> [<hex formatted data>]) 222 * fixed PMF protection of Deauthentication frame when this is triggered 223 by session timeout 224 * internal TLS implementation enhancements/fixes 225 - add SHA256-based cipher suites 226 - add DHE-RSA cipher suites 227 - fix X.509 validation of PKCS#1 signature to check for extra data 228 * RADIUS server functionality 229 - add minimal RADIUS accounting server support (hostapd-as-server); 230 this is mainly to enable testing coverage with hwsim scripts 231 - allow authentication log to be written into SQLite databse 232 - added option for TLS protocol testing of an EAP peer by simulating 233 various misbehaviors/known attacks 234 - MAC ACL support for testing purposes 235 * fixed PTK derivation for CCMP-256 and GCMP-256 236 * extended WPS per-station PSK to support ER case 237 * added option to configure the management group cipher 238 (group_mgmt_cipher=AES-128-CMAC (default), BIP-GMAC-128, BIP-GMAC-256, 239 BIP-CMAC-256) 240 * fixed AP mode default TXOP Limit values for AC_VI and AC_VO (these 241 were rounded incorrectly) 242 * added support for postponing FT response in case PMK-R1 needs to be 243 pulled from R0KH 244 * added option to advertise 40 MHz intolerant HT capability with 245 ht_capab=[40-INTOLERANT] 246 * remove WPS 1.0 only support, i.e., WSC 2.0 support is now enabled 247 whenever CONFIG_WPS=y is set 248 * EAP-pwd fixes 249 - fix possible segmentation fault on EAP method deinit if an invalid 250 group is negotiated 251 * fixed RADIUS client retransmit/failover behavior 252 - there was a potential ctash due to freed memory being accessed 253 - failover to a backup server mechanism did not work properly 254 * fixed a possible crash on double DISABLE command when multiple BSSes 255 are enabled 256 * fixed a memory leak in SAE random number generation 257 * fixed GTK rekeying when the station uses FT protocol 258 * fixed off-by-one bounds checking in printf_encode() 259 - this could result in deinial of service in some EAP server cases 260 * various bug fixes 261 2622014-02-04 - v2.1 263 * added support for simultaneous authentication of equals (SAE) for 264 stronger password-based authentication with WPA2-Personal 265 * added nl80211 functionality 266 - VHT configuration for nl80211 267 - support split wiphy dump 268 - driver-based MAC ACL 269 - QoS Mapping configuration 270 * added fully automated regression testing with mac80211_hwsim 271 * allow ctrl_iface group to be specified on command line (-G<group>) 272 * allow single hostapd process to control independent WPS interfaces 273 (wps_independent=1) instead of synchronized operations through all 274 configured interfaces within a process 275 * avoid processing received management frames multiple times when using 276 nl80211 with multiple BSSes 277 * added support for DFS (processing radar detection events, CAC, channel 278 re-selection) 279 * added EAP-EKE server 280 * added automatic channel selection (ACS) 281 * added option for using per-BSS (vif) configuration files with 282 -b<phyname>:<config file name> 283 * extended global control interface ADD/REMOVE commands to allow BSSes 284 of a radio to be removed individually without having to add/remove all 285 other BSSes of the radio at the same time 286 * added support for sending debug info to Linux tracing (-T on command 287 line) 288 * replace dump_file functionality with same information being available 289 through the hostapd control interface 290 * added support for using Protected Dual of Public Action frames for 291 GAS/ANQP exchanges when PMF is enabled 292 * added support for WPS+NFC updates 293 - improved protocol 294 - option to fetch and report alternative carrier records for external 295 NFC operations 296 * various bug fixes 297 2982013-01-12 - v2.0 299 * added AP-STA-DISCONNECTED ctrl_iface event 300 * improved debug logging (human readable event names, interface name 301 included in more entries) 302 * added number of small changes to make it easier for static analyzers 303 to understand the implementation 304 * added a workaround for Windows 7 Michael MIC failure reporting and 305 use of the Secure bit in EAPOL-Key msg 3/4 306 * fixed number of small bugs (see git logs for more details) 307 * changed OpenSSL to read full certificate chain from server_cert file 308 * nl80211: number of updates to use new cfg80211/nl80211 functionality 309 - replace monitor interface with nl80211 commands 310 - additional information for driver-based AP SME 311 * EAP-pwd: 312 - fix KDF for group 21 and zero-padding 313 - added support for fragmentation 314 - increased maximum number of hunting-and-pecking iterations 315 * avoid excessive Probe Response retries for broadcast Probe Request 316 frames (only with drivers using hostapd SME/MLME) 317 * added preliminary support for using TLS v1.2 (CONFIG_TLSV12=y) 318 * fixed WPS operation stopping on dual concurrent AP 319 * added wps_rf_bands configuration parameter for overriding RF Bands 320 value for WPS 321 * added support for getting per-device PSK from RADIUS Tunnel-Password 322 * added support for libnl 3.2 and newer 323 * increased initial group key handshake retransmit timeout to 500 ms 324 * added a workaround for 4-way handshake to update SNonce even after 325 having sent EAPOL-Key 3/4 to avoid issues with some supplicant 326 implementations that can change SNonce for each EAP-Key 2/4 327 * added a workaround for EAPOL-Key 4/4 using incorrect type value in 328 WPA2 mode (some deployed stations use WPA type in that message) 329 * added a WPS workaround for mixed mode AP Settings with Windows 7 330 * changed WPS AP PIN disabling mechanism to disable the PIN after 10 331 consecutive failures in addition to using the exponential lockout 332 period 333 * added support for WFA Hotspot 2.0 334 - GAS/ANQP advertisement of network information 335 - disable_dgaf parameter to disable downstream group-addressed 336 forwarding 337 * simplified licensing terms by selecting the BSD license as the only 338 alternative 339 * EAP-SIM: fixed re-authentication not to update pseudonym 340 * EAP-SIM: use Notification round before EAP-Failure 341 * EAP-AKA: added support for AT_COUNTER_TOO_SMALL 342 * EAP-AKA: skip AKA/Identity exchange if EAP identity is recognized 343 * EAP-AKA': fixed identity for MK derivation 344 * EAP-AKA': updated to RFC 5448 (username prefixes changed); note: this 345 breaks interoperability with older versions 346 * EAP-SIM/AKA: allow pseudonym to be used after unknown reauth id 347 * changed ANonce to be a random number instead of Counter-based 348 * added support for canceling WPS operations with hostapd_cli wps_cancel 349 * fixed EAP/WPS to PSK transition on reassociation in cases where 350 deauthentication is missed 351 * hlr_auc_gw enhancements: 352 - a new command line parameter -u can be used to enable updating of 353 SQN in Milenage file 354 - use 5 bit IND for SQN updates 355 - SQLite database can now be used to store Milenage information 356 * EAP-SIM/AKA DB: added optional use of SQLite database for pseudonyms 357 and reauth data 358 * added support for Chargeable-User-Identity (RFC 4372) 359 * added radius_auth_req_attr and radius_acct_req_attr configuration 360 parameters to allow adding/overriding of RADIUS attributes in 361 Access-Request and Accounting-Request packets 362 * added support for RADIUS dynamic authorization server (RFC 5176) 363 * added initial support for WNM operations 364 - BSS max idle period 365 - WNM-Sleep Mode 366 * added new WPS NFC ctrl_iface mechanism 367 - removed obsoleted WPS_OOB command (including support for deprecated 368 UFD config_method) 369 * added FT support for drivers that implement MLME internally 370 * added SA Query support for drivers that implement MLME internally 371 * removed default ACM=1 from AC_VO and AC_VI 372 * changed VENDOR-TEST EAP method to use proper private enterprise number 373 (this will not interoperate with older versions) 374 * added hostapd.conf parameter vendor_elements to allow arbitrary vendor 375 specific elements to be added to the Beacon and Probe Response frames 376 * added support for configuring GCMP cipher for IEEE 802.11ad 377 * added support for 256-bit AES with internal TLS implementation 378 * changed EAPOL transmission to use AC_VO if WMM is active 379 * fixed EAP-TLS/PEAP/TTLS/FAST server to validate TLS Message Length 380 correctly; invalid messages could have caused the hostapd process to 381 terminate before this fix [CVE-2012-4445] 382 * limit number of active wildcard PINs for WPS Registrar to one to avoid 383 confusing behavior with multiple wildcard PINs 384 * added a workaround for WPS PBC session overlap detection to avoid 385 interop issues with deployed station implementations that do not 386 remove active PBC indication from Probe Request frames properly 387 * added support for using SQLite for the eap_user database 388 * added Acct-Session-Id attribute into Access-Request messages 389 * fixed EAPOL frame transmission to non-QoS STAs with nl80211 390 (do not send QoS frames if the STA did not negotiate use of QoS for 391 this association) 392 3932012-05-10 - v1.0 394 * Add channel selection support in hostapd. See hostapd.conf. 395 * Add support for IEEE 802.11v Time Advertisement mechanism with UTC 396 TSF offset. See hostapd.conf for config info. 397 * Delay STA entry removal until Deauth/Disassoc TX status in AP mode. 398 This allows the driver to use PS buffering of Deauthentication and 399 Disassociation frames when the STA is in power save sleep. Only 400 available with drivers that provide TX status events for Deauth/ 401 Disassoc frames (nl80211). 402 * Allow PMKSA caching to be disabled on the Authenticator. See 403 hostap.conf config parameter disable_pmksa_caching. 404 * atheros: Add support for IEEE 802.11w configuration. 405 * bsd: Add support for setting HT values in IFM_MMASK. 406 * Allow client isolation to be configured with ap_isolate. Client 407 isolation can be used to prevent low-level bridging of frames 408 between associated stations in the BSS. By default, this bridging 409 is allowed. 410 * Allow coexistance of HT BSSes with WEP/TKIP BSSes. 411 * Add require_ht config parameter, which can be used to configure 412 hostapd to reject association with any station that does not support 413 HT PHY. 414 * Add support for writing debug log to a file using "-f" option. Also 415 add relog CLI command to re-open the log file. 416 * Add bridge handling for WDS STA interfaces. By default they are 417 added to the configured bridge of the AP interface (if present), 418 but the user can also specify a separate bridge using cli command 419 wds_bridge. 420 * hostapd_cli: 421 - Add wds_bridge command for specifying bridge for WDS STA 422 interfaces. 423 - Add relog command for reopening log file. 424 - Send AP-STA-DISCONNECTED event when an AP disconnects a station 425 due to inactivity. 426 - Add wps_config ctrl_interface command for configuring AP. This 427 command can be used to configure the AP using the internal WPS 428 registrar. It works in the same way as new AP settings received 429 from an ER. 430 - Many WPS/WPS ER commands - see WPS/WPS ER sections for details. 431 - Add command get version, that returns hostapd version string. 432 * WNM: Add BSS Transition Management Request for ESS Disassoc Imminent. 433 Use hostapd_cli ess_disassoc (STA addr) (URL) to send the 434 notification to the STA. 435 * Allow AP mode to disconnect STAs based on low ACK condition (when 436 the data connection is not working properly, e.g., due to the STA 437 going outside the range of the AP). Disabled by default, enable by 438 config option disassoc_low_ack. 439 * Add WPA_IGNORE_CONFIG_ERRORS build option to continue in case of bad 440 config file. 441 * WPS: 442 - Send AP Settings as a wrapped Credential attribute to ctrl_iface 443 in WPS-NEW-AP-SETTINGS. 444 - Dispatch more WPS events through hostapd ctrl_iface. 445 - Add mechanism for indicating non-standard WPS errors. 446 - Change concurrent radio AP to use only one WPS UPnP instance. 447 - Add wps_check_pin command for processing PIN from user input. 448 UIs can use this command to process a PIN entered by a user and to 449 validate the checksum digit (if present). 450 - Add hostap_cli get_config command to display current AP config. 451 - Add new hostapd_cli command, wps_ap_pin, to manage AP PIN at 452 runtime and support dynamic AP PIN management. 453 - Disable AP PIN after 10 consecutive failures. Slow down attacks 454 on failures up to 10. 455 - Allow AP to start in Enrollee mode without AP PIN for probing, 456 to be compatible with Windows 7. 457 - Add Config Error into WPS-FAIL events to provide more info 458 to the user on how to resolve the issue. 459 - When controlling multiple interfaces: 460 - apply WPS commands to all interfaces configured to use WPS 461 - apply WPS config changes to all interfaces that use WPS 462 - when an attack is detected on any interface, disable AP PIN on 463 all interfaces 464 * WPS ER: 465 - Show SetSelectedRegistrar events as ctrl_iface events. 466 - Add special AP Setup Locked mode to allow read only ER. 467 ap_setup_locked=2 can now be used to enable a special mode where 468 WPS ER can learn the current AP settings, but cannot change them. 469 * WPS 2.0: Add support for WPS 2.0 (CONFIG_WPS2) 470 - Add build option CONFIG_WPS_EXTENSIBILITY_TESTING to enable tool 471 for testing protocol extensibility. 472 - Add build option CONFIG_WPS_STRICT to allow disabling of WPS 473 workarounds. 474 - Add support for AuthorizedMACs attribute. 475 * TDLS: 476 - Allow TDLS use or TDLS channel switching in the BSS to be 477 prohibited in the BSS, using config params tdls_prohibit and 478 tdls_prohibit_chan_switch. 479 * EAP server: Add support for configuring fragment size (see 480 fragment_size in hostapd.conf). 481 * wlantest: Add a tool wlantest for IEEE802.11 protocol testing. 482 wlantest can be used to capture frames from a monitor interface 483 for realtime capturing or from pcap files for offline analysis. 484 * Interworking: Support added for 802.11u. Enable in .config with 485 CONFIG_INTERWORKING. See hostapd.conf for config parameters for 486 interworking. 487 * Android: Add build and runtime support for Android hostapd. 488 * Add a new debug message level for excessive information. Use 489 -ddd to enable. 490 * TLS: Add support for tls_disable_time_checks=1 in client mode. 491 * Internal TLS: 492 - Add support for TLS v1.1 (RFC 4346). Enable with build parameter 493 CONFIG_TLSV11. 494 - Add domainComponent parser for X.509 names 495 * Reorder some IEs to get closer to IEEE 802.11 standard. Move 496 WMM into end of Beacon, Probe Resp and (Re)Assoc Resp frames. 497 Move HT IEs to be later in (Re)Assoc Resp. 498 * Many bugfixes. 499 5002010-04-18 - v0.7.2 501 * fix WPS internal Registrar use when an external Registrar is also 502 active 503 * bsd: Cleaned up driver wrapper and added various low-level 504 configuration options 505 * TNC: fixed issues with fragmentation 506 * EAP-TNC: add Flags field into fragment acknowledgement (needed to 507 interoperate with other implementations; may potentially breaks 508 compatibility with older wpa_supplicant/hostapd versions) 509 * cleaned up driver wrapper API for multi-BSS operations 510 * nl80211: fix multi-BSS and VLAN operations 511 * fix number of issues with IEEE 802.11r/FT; this version is not 512 backwards compatible with old versions 513 * add SA Query Request processing in AP mode (IEEE 802.11w) 514 * fix IGTK PN in group rekeying (IEEE 802.11w) 515 * fix WPS PBC session overlap detection to use correct attribute 516 * hostapd_notif_Assoc() can now be called with all IEs to simplify 517 driver wrappers 518 * work around interoperability issue with some WPS External Registrar 519 implementations 520 * nl80211: fix WPS IE update 521 * hostapd_cli: add support for action script operations (run a script 522 on hostapd events) 523 * fix DH padding with internal crypto code (mainly, for WPS) 524 * fix WPS association with both WPS IE and WPA/RSN IE present with 525 driver wrappers that use hostapd MLME (e.g., nl80211) 526 5272010-01-16 - v0.7.1 528 * cleaned up driver wrapper API (struct wpa_driver_ops); the new API 529 is not fully backwards compatible, so out-of-tree driver wrappers 530 will need modifications 531 * cleaned up various module interfaces 532 * merge hostapd and wpa_supplicant developers' documentation into a 533 single document 534 * fixed HT Capabilities IE with nl80211 drivers 535 * moved generic AP functionality code into src/ap 536 * WPS: handle Selected Registrar as union of info from all Registrars 537 * remove obsolte Prism54.org driver wrapper 538 * added internal debugging mechanism with backtrace support and memory 539 allocation/freeing validation, etc. tests (CONFIG_WPA_TRACE=y) 540 * EAP-FAST server: piggyback Phase 2 start with the end of Phase 1 541 * WPS: add support for dynamically selecting whether to provision the 542 PSK as an ASCII passphrase or PSK 543 * added support for WDS (4-address frame) mode with per-station virtual 544 interfaces (wds_sta=1 in config file; only supported with 545 driver=nl80211 for now) 546 * fixed WPS Probe Request processing to handle missing required 547 attribute 548 * fixed PKCS#12 use with OpenSSL 1.0.0 549 * detect bridge interface automatically so that bridge parameter in 550 hostapd.conf becomes optional (though, it may now be used to 551 automatically add then WLAN interface into a bridge with 552 driver=nl80211) 553 5542009-11-21 - v0.7.0 555 * increased hostapd_cli ping interval to 5 seconds and made this 556 configurable with a new command line options (-G<seconds>) 557 * driver_nl80211: use Linux socket filter to improve performance 558 * added support for external Registrars with WPS (UPnP transport) 559 * 802.11n: scan for overlapping BSSes before starting 20/40 MHz channel 560 * driver_nl80211: fixed STA accounting data collection (TX/RX bytes 561 reported correctly; TX/RX packets not yet available from kernel) 562 * added support for WPS USBA out-of-band mechanism with USB Flash 563 Drives (UFD) (CONFIG_WPS_UFD=y) 564 * fixed EAPOL/EAP reauthentication when using an external RADIUS 565 authentication server 566 * fixed TNC with EAP-TTLS 567 * fixed IEEE 802.11r key derivation function to match with the standard 568 (note: this breaks interoperability with previous version) [Bug 303] 569 * fixed SHA-256 based key derivation function to match with the 570 standard when using CCMP (for IEEE 802.11r and IEEE 802.11w) 571 (note: this breaks interoperability with previous version) [Bug 307] 572 * added number of code size optimizations to remove unnecessary 573 functionality from the program binary based on build configuration 574 (part of this automatic; part configurable with CONFIG_NO_* build 575 options) 576 * use shared driver wrapper files with wpa_supplicant 577 * driver_nl80211: multiple updates to provide support for new Linux 578 nl80211/mac80211 functionality 579 * updated management frame protection to use IEEE Std 802.11w-2009 580 * fixed number of small WPS issues and added workarounds to 581 interoperate with common deployed broken implementations 582 * added some IEEE 802.11n co-existence rules to disable 40 MHz channels 583 or modify primary/secondary channels if needed based on neighboring 584 networks 585 * added support for NFC out-of-band mechanism with WPS 586 * added preliminary support for IEEE 802.11r RIC processing 587 5882009-01-06 - v0.6.7 589 * added support for Wi-Fi Protected Setup (WPS) 590 (hostapd can now be configured to act as an integrated WPS Registrar 591 and provision credentials for WPS Enrollees using PIN and PBC 592 methods; external wireless Registrar can configure the AP, but 593 external WLAN Manager Registrars are not supported); WPS support can 594 be enabled by adding CONFIG_WPS=y into .config and setting the 595 runtime configuration variables in hostapd.conf (see WPS section in 596 the example configuration file); new hostapd_cli commands wps_pin and 597 wps_pbc are used to configure WPS negotiation; see README-WPS for 598 more details 599 * added IEEE 802.11n HT capability configuration (ht_capab) 600 * added support for generating Country IE based on nl80211 regulatory 601 information (added if ieee80211d=1 in configuration) 602 * fixed WEP authentication (both Open System and Shared Key) with 603 mac80211 604 * added support for EAP-AKA' (draft-arkko-eap-aka-kdf) 605 * added support for using driver_test over UDP socket 606 * changed EAP-GPSK to use the IANA assigned EAP method type 51 607 * updated management frame protection to use IEEE 802.11w/D7.0 608 * fixed retransmission of EAP requests if no response is received 609 6102008-11-23 - v0.6.6 611 * added a new configuration option, wpa_ptk_rekey, that can be used to 612 enforce frequent PTK rekeying, e.g., to mitigate some attacks against 613 TKIP deficiencies 614 * updated OpenSSL code for EAP-FAST to use an updated version of the 615 session ticket overriding API that was included into the upstream 616 OpenSSL 0.9.9 tree on 2008-11-15 (no additional OpenSSL patch is 617 needed with that version anymore) 618 * changed channel flags configuration to read the information from 619 the driver (e.g., via driver_nl80211 when using mac80211) instead of 620 using hostapd as the source of the regulatory information (i.e., 621 information from CRDA is now used with mac80211); this allows 5 GHz 622 channels to be used with hostapd (if allowed in the current 623 regulatory domain) 624 * fixed EAP-TLS message processing for the last TLS message if it is 625 large enough to require fragmentation (e.g., if a large Session 626 Ticket data is included) 627 * fixed listen interval configuration for nl80211 drivers 628 6292008-11-01 - v0.6.5 630 * added support for SHA-256 as X.509 certificate digest when using the 631 internal X.509/TLSv1 implementation 632 * fixed EAP-FAST PAC-Opaque padding (0.6.4 broke this for some peer 633 identity lengths) 634 * fixed internal TLSv1 implementation for abbreviated handshake (used 635 by EAP-FAST server) 636 * added support for setting VLAN ID for STAs based on local MAC ACL 637 (accept_mac_file) as an alternative for RADIUS server-based 638 configuration 639 * updated management frame protection to use IEEE 802.11w/D6.0 640 (adds a new association ping to protect against unauthenticated 641 authenticate or (re)associate request frames dropping association) 642 * added support for using SHA256-based stronger key derivation for WPA2 643 (IEEE 802.11w) 644 * added new "driver wrapper" for RADIUS-only configuration 645 (driver=none in hostapd.conf; CONFIG_DRIVER_NONE=y in .config) 646 * fixed WPA/RSN IE validation to verify that the proto (WPA vs. WPA2) 647 is enabled in configuration 648 * changed EAP-FAST configuration to use separate fields for A-ID and 649 A-ID-Info (eap_fast_a_id_info) to allow A-ID to be set to a fixed 650 16-octet len binary value for better interoperability with some peer 651 implementations; eap_fast_a_id is now configured as a hex string 652 * driver_nl80211: Updated to match the current Linux mac80211 AP mode 653 configuration (wireless-testing.git and Linux kernel releases 654 starting from 2.6.29) 655 6562008-08-10 - v0.6.4 657 * added peer identity into EAP-FAST PAC-Opaque and skip Phase 2 658 Identity Request if identity is already known 659 * added support for EAP Sequences in EAP-FAST Phase 2 660 * added support for EAP-TNC (Trusted Network Connect) 661 (this version implements the EAP-TNC method and EAP-TTLS/EAP-FAST 662 changes needed to run two methods in sequence (IF-T) and the IF-IMV 663 and IF-TNCCS interfaces from TNCS) 664 * added support for optional cryptobinding with PEAPv0 665 * added fragmentation support for EAP-TNC 666 * added support for fragmenting EAP-TTLS/PEAP/FAST Phase 2 (tunneled) 667 data 668 * added support for opportunistic key caching (OKC) 669 6702008-02-22 - v0.6.3 671 * fixed Reassociation Response callback processing when using internal 672 MLME (driver_{hostap,nl80211,test}.c) 673 * updated FT support to use the latest draft, IEEE 802.11r/D9.0 674 * copy optional Proxy-State attributes into RADIUS response when acting 675 as a RADIUS authentication server 676 * fixed EAPOL state machine to handle a case in which no response is 677 received from the RADIUS authentication server; previous version 678 could have triggered a crash in some cases after a timeout 679 * fixed EAP-SIM/AKA realm processing to allow decorated usernames to 680 be used 681 * added a workaround for EAP-SIM/AKA peers that include incorrect null 682 termination in the username 683 * fixed EAP-SIM/AKA protected result indication to include AT_COUNTER 684 attribute in notification messages only when using fast 685 reauthentication 686 * fixed EAP-SIM Start response processing for fast reauthentication 687 case 688 * added support for pending EAP processing in EAP-{PEAP,TTLS,FAST} 689 phase 2 to allow EAP-SIM and EAP-AKA to be used as the Phase 2 method 690 6912008-01-01 - v0.6.2 692 * fixed EAP-SIM and EAP-AKA message parser to validate attribute 693 lengths properly to avoid potential crash caused by invalid messages 694 * added data structure for storing allocated buffers (struct wpabuf); 695 this does not affect hostapd usage, but many of the APIs changed 696 and various interfaces (e.g., EAP) is not compatible with old 697 versions 698 * added support for protecting EAP-AKA/Identity messages with 699 AT_CHECKCODE (optional feature in RFC 4187) 700 * added support for protected result indication with AT_RESULT_IND for 701 EAP-SIM and EAP-AKA (eap_sim_aka_result_ind=1) 702 * added support for configuring EAP-TTLS phase 2 non-EAP methods in 703 EAP server configuration; previously all four were enabled for every 704 phase 2 user, now all four are disabled by default and need to be 705 enabled with new method names TTLS-PAP, TTLS-CHAP, TTLS-MSCHAP, 706 TTLS-MSCHAPV2 707 * removed old debug printing mechanism and the related 'debug' 708 parameter in the configuration file; debug verbosity is now set with 709 -d (or -dd) command line arguments 710 * added support for EAP-IKEv2 (draft-tschofenig-eap-ikev2-15.txt); 711 only shared key/password authentication is supported in this version 712 7132007-11-24 - v0.6.1 714 * added experimental, integrated TLSv1 server implementation with the 715 needed X.509/ASN.1/RSA/bignum processing (this can be enabled by 716 setting CONFIG_TLS=internal and CONFIG_INTERNAL_LIBTOMMATH=y in 717 .config); this can be useful, e.g., if the target system does not 718 have a suitable TLS library and a minimal code size is required 719 * added support for EAP-FAST server method to the integrated EAP 720 server 721 * updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest 722 draft (draft-ietf-emu-eap-gpsk-07.txt) 723 * added a new configuration parameter, rsn_pairwise, to allow different 724 pairwise cipher suites to be enabled for WPA and RSN/WPA2 725 (note: if wpa_pairwise differs from rsn_pairwise, the driver will 726 either need to support this or will have to use the WPA/RSN IEs from 727 hostapd; currently, the included madwifi and bsd driver interfaces do 728 not have support for this) 729 * updated FT support to use the latest draft, IEEE 802.11r/D8.0 730 7312007-05-28 - v0.6.0 732 * added experimental IEEE 802.11r/D6.0 support 733 * updated EAP-SAKE to RFC 4763 and the IANA-allocated EAP type 48 734 * updated EAP-PSK to use the IANA-allocated EAP type 47 735 * fixed EAP-PSK bit ordering of the Flags field 736 * fixed configuration reloading (SIGHUP) to re-initialize WPA PSKs 737 by reading wpa_psk_file [Bug 181] 738 * fixed EAP-TTLS AVP parser processing for too short AVP lengths 739 * fixed IPv6 connection to RADIUS accounting server 740 * updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest 741 draft (draft-ietf-emu-eap-gpsk-04.txt) 742 * hlr_auc_gw: read GSM triplet file into memory and rotate through the 743 entries instead of only using the same three triplets every time 744 (this does not work properly with tests using multiple clients, but 745 provides bit better triplet data for testing a single client; anyway, 746 if a better quality triplets are needed, GSM-Milenage should be used 747 instead of hardcoded triplet file) 748 * fixed EAP-MSCHAPv2 server to use a space between S and M parameters 749 in Success Request [Bug 203] 750 * added support for sending EAP-AKA Notifications in error cases 751 * updated to use IEEE 802.11w/D2.0 for management frame protection 752 (still experimental) 753 * RADIUS server: added support for processing duplicate messages 754 (retransmissions from RADIUS client) by replying with the previous 755 reply 756 7572006-11-24 - v0.5.6 758 * added support for configuring and controlling multiple BSSes per 759 radio interface (bss=<ifname> in hostapd.conf); this is only 760 available with Devicescape and test driver interfaces 761 * fixed PMKSA cache update in the end of successful RSN 762 pre-authentication 763 * added support for dynamic VLAN configuration (i.e., selecting VLAN-ID 764 for each STA based on RADIUS Access-Accept attributes); this requires 765 VLAN support from the kernel driver/802.11 stack and this is 766 currently only available with Devicescape and test driver interfaces 767 * driver_madwifi: fixed configuration of unencrypted modes (plaintext 768 and IEEE 802.1X without WEP) 769 * removed STAKey handshake since PeerKey handshake has replaced it in 770 IEEE 802.11ma and there are no known deployments of STAKey 771 * updated EAP Generalized Pre-Shared Key (EAP-GPSK) to use the latest 772 draft (draft-ietf-emu-eap-gpsk-01.txt) 773 * added preliminary implementation of IEEE 802.11w/D1.0 (management 774 frame protection) 775 (Note: this requires driver support to work properly.) 776 (Note2: IEEE 802.11w is an unapproved draft and subject to change.) 777 * hlr_auc_gw: added support for GSM-Milenage (for EAP-SIM) 778 * hlr_auc_gw: added support for reading per-IMSI Milenage keys and 779 parameters from a text file to make it possible to implement proper 780 GSM/UMTS authentication server for multiple SIM/USIM cards using 781 EAP-SIM/EAP-AKA 782 * fixed session timeout processing with drivers that do not use 783 ieee802_11.c (e.g., madwifi) 784 7852006-08-27 - v0.5.5 786 * added 'hostapd_cli new_sta <addr>' command for adding a new STA into 787 hostapd (e.g., to initialize wired network authentication based on an 788 external signal) 789 * fixed hostapd to add PMKID KDE into 4-Way Handshake Message 1 when 790 using WPA2 even if PMKSA caching is not used 791 * added -P<pid file> argument for hostapd to write the current process 792 id into a file 793 * added support for RADIUS Authentication Server MIB (RFC 2619) 794 7952006-06-20 - v0.5.4 796 * fixed nt_password_hash build [Bug 144] 797 * added PeerKey handshake implementation for IEEE 802.11e 798 direct link setup (DLS) to replace STAKey handshake 799 * added support for EAP Generalized Pre-Shared Key (EAP-GPSK, 800 draft-clancy-emu-eap-shared-secret-00.txt) 801 * fixed a segmentation fault when RSN pre-authentication was completed 802 successfully [Bug 152] 803 8042006-04-27 - v0.5.3 805 * do not build nt_password_hash and hlr_auc_gw by default to avoid 806 requiring a TLS library for a successful build; these programs can be 807 build with 'make nt_password_hash' and 'make hlr_auc_gw' 808 * added a new configuration option, eapol_version, that can be used to 809 set EAPOL version to 1 (default is 2) to work around broken client 810 implementations that drop EAPOL frames which use version number 2 811 [Bug 89] 812 * added support for EAP-SAKE (no EAP method number allocated yet, so 813 this is using the same experimental type 255 as EAP-PSK) 814 * fixed EAP-MSCHAPv2 message length validation 815 8162006-03-19 - v0.5.2 817 * fixed stdarg use in hostapd_logger(): if both stdout and syslog 818 logging was enabled, hostapd could trigger a segmentation fault in 819 vsyslog on some CPU -- C library combinations 820 * moved HLR/AuC gateway implementation for EAP-SIM/AKA into an external 821 program to make it easier to use for implementing real SS7 gateway; 822 eap_sim_db is not anymore used as a file name for GSM authentication 823 triplets; instead, it is path to UNIX domain socket that will be used 824 to communicate with the external gateway program (e.g., hlr_auc_gw) 825 * added example HLR/AuC gateway implementation, hlr_auc_gw, that uses 826 local information (GSM authentication triplets from a text file and 827 hardcoded AKA authentication data); this can be used to test EAP-SIM 828 and EAP-AKA 829 * added Milenage algorithm (example 3GPP AKA algorithm) to hlr_auc_gw 830 to make it possible to test EAP-AKA with real USIM cards (this is 831 disabled by default; define AKA_USE_MILENAGE when building hlr_auc_gw 832 to enable this) 833 * driver_madwifi: added support for getting station RSN IE from 834 madwifi-ng svn r1453 and newer; this fixes RSN that was apparently 835 broken with earlier change (r1357) in the driver 836 * changed EAP method registration to use a dynamic list of methods 837 instead of a static list generated at build time 838 * fixed WPA message 3/4 not to encrypt Key Data field (WPA IE) 839 [Bug 125] 840 * added ap_max_inactivity configuration parameter 841 8422006-01-29 - v0.5.1 843 * driver_test: added better support for multiple APs and STAs by using 844 a directory with sockets that include MAC address for each device in 845 the name (test_socket=DIR:/tmp/test) 846 * added support for EAP expanded type (vendor specific EAP methods) 847 8482005-12-18 - v0.5.0 (beginning of 0.5.x development releases) 849 * added experimental STAKey handshake implementation for IEEE 802.11e 850 direct link setup (DLS); note: this is disabled by default in both 851 build and runtime configuration (can be enabled with CONFIG_STAKEY=y 852 and stakey=1) 853 * added support for EAP methods to use callbacks to external programs 854 by buffering a pending request and processing it after the EAP method 855 is ready to continue 856 * improved EAP-SIM database interface to allow external request to GSM 857 HLR/AuC without blocking hostapd process 858 * added support for using EAP-SIM pseudonyms and fast re-authentication 859 * added support for EAP-AKA in the integrated EAP authenticator 860 * added support for matching EAP identity prefixes (e.g., "1"*) in EAP 861 user database to allow EAP-SIM/AKA selection without extra roundtrip 862 for EAP-Nak negotiation 863 * added support for storing EAP user password as NtPasswordHash instead 864 of plaintext password when using MSCHAP or MSCHAPv2 for 865 authentication (hash:<16-octet hex value>); added nt_password_hash 866 tool for hashing password to generate NtPasswordHash 867 8682005-11-20 - v0.4.7 (beginning of 0.4.x stable releases) 869 * driver_wired: fixed EAPOL sending to optionally use PAE group address 870 as the destination instead of supplicant MAC address; this is 871 disabled by default, but should be enabled with use_pae_group_addr=1 872 in configuration file if the wired interface is used by only one 873 device at the time (common switch configuration) 874 * driver_madwifi: configure driver to use TKIP countermeasures in order 875 to get correct behavior (IEEE 802.11 association failing; previously, 876 association succeeded, but hostpad forced disassociation immediately) 877 * driver_madwifi: added support for madwifi-ng 878 8792005-10-27 - v0.4.6 880 * added support for replacing user identity from EAP with RADIUS 881 User-Name attribute from Access-Accept message, if that is included, 882 for the RADIUS accounting messages (e.g., for EAP-PEAP/TTLS to get 883 tunneled identity into accounting messages when the RADIUS server 884 does not support better way of doing this with Class attribute) 885 * driver_madwifi: fixed EAPOL packet receive for configuration where 886 ath# is part of a bridge interface 887 * added a configuration file and log analyzer script for logwatch 888 * fixed EAPOL state machine step function to process all state 889 transitions before processing new events; this resolves a race 890 condition in which EAPOL-Start message could trigger hostapd to send 891 two EAP-Response/Identity frames to the authentication server 892 8932005-09-25 - v0.4.5 894 * added client CA list to the TLS certificate request in order to make 895 it easier for the client to select which certificate to use 896 * added experimental support for EAP-PSK 897 * added support for WE-19 (hostap, madwifi) 898 8992005-08-21 - v0.4.4 900 * fixed build without CONFIG_RSN_PREAUTH 901 * fixed FreeBSD build 902 9032005-06-26 - v0.4.3 904 * fixed PMKSA caching to copy User-Name and Class attributes so that 905 RADIUS accounting gets correct information 906 * start RADIUS accounting only after successful completion of WPA 907 4-Way Handshake if WPA-PSK is used 908 * fixed PMKSA caching for the case where STA (re)associates without 909 first disassociating 910 9112005-06-12 - v0.4.2 912 * EAP-PAX is now registered as EAP type 46 913 * fixed EAP-PAX MAC calculation 914 * fixed EAP-PAX CK and ICK key derivation 915 * renamed eap_authenticator configuration variable to eap_server to 916 better match with RFC 3748 (EAP) terminology 917 * driver_test: added support for testing hostapd with wpa_supplicant 918 by using test driver interface without any kernel drivers or network 919 cards 920 9212005-05-22 - v0.4.1 922 * fixed RADIUS server initialization when only auth or acct server 923 is configured and the other one is left empty 924 * driver_madwifi: added support for RADIUS accounting 925 * driver_madwifi: added preliminary support for compiling against 'BSD' 926 branch of madwifi CVS tree 927 * driver_madwifi: fixed pairwise key removal to allow WPA reauth 928 without disassociation 929 * added support for reading additional certificates from PKCS#12 files 930 and adding them to the certificate chain 931 * fixed RADIUS Class attribute processing to only use Access-Accept 932 packets to update Class; previously, other RADIUS authentication 933 packets could have cleared Class attribute 934 * added support for more than one Class attribute in RADIUS packets 935 * added support for verifying certificate revocation list (CRL) when 936 using integrated EAP authenticator for EAP-TLS; new hostapd.conf 937 options 'check_crl'; CRL must be included in the ca_cert file for now 938 9392005-04-25 - v0.4.0 (beginning of 0.4.x development releases) 940 * added support for including network information into 941 EAP-Request/Identity message (ASCII-0 (nul) in eap_message) 942 (e.g., to implement draft-adrange-eap-network-discovery-07.txt) 943 * fixed a bug which caused some RSN pre-authentication cases to use 944 freed memory and potentially crash hostapd 945 * fixed private key loading for cases where passphrase is not set 946 * added support for sending TLS alerts and aborting authentication 947 when receiving a TLS alert 948 * fixed WPA2 to add PMKSA cache entry when using integrated EAP 949 authenticator 950 * fixed PMKSA caching (EAP authentication was not skipped correctly 951 with the new state machine changes from IEEE 802.1X draft) 952 * added support for RADIUS over IPv6; own_ip_addr, auth_server_addr, 953 and acct_server_addr can now be IPv6 addresses (CONFIG_IPV6=y needs 954 to be added to .config to include IPv6 support); for RADIUS server, 955 radius_server_ipv6=1 needs to be set in hostapd.conf and addresses 956 in RADIUS clients file can then use IPv6 format 957 * added experimental support for EAP-PAX 958 * replaced hostapd control interface library (hostapd_ctrl.[ch]) with 959 the same implementation that wpa_supplicant is using (wpa_ctrl.[ch]) 960 9612005-02-12 - v0.3.7 (beginning of 0.3.x stable releases) 962 9632005-01-23 - v0.3.5 964 * added support for configuring a forced PEAP version based on the 965 Phase 1 identity 966 * fixed PEAPv1 to use tunneled EAP-Success/Failure instead of EAP-TLV 967 to terminate authentication 968 * fixed EAP identifier duplicate processing with the new IEEE 802.1X 969 draft 970 * clear accounting data in the driver when starting a new accounting 971 session 972 * driver_madwifi: filter wireless events based on ifindex to allow more 973 than one network interface to be used 974 * fixed WPA message 2/4 processing not to cancel timeout for TimeoutEvt 975 setting if the packet does not pass MIC verification (e.g., due to 976 incorrect PSK); previously, message 1/4 was not tried again if an 977 invalid message 2/4 was received 978 * fixed reconfiguration of RADIUS client retransmission timer when 979 adding a new message to the pending list; previously, timer was not 980 updated at this point and if there was a pending message with long 981 time for the next retry, the new message needed to wait that long for 982 its first retry, too 983 9842005-01-09 - v0.3.4 985 * added support for configuring multiple allowed EAP types for Phase 2 986 authentication (EAP-PEAP, EAP-TTLS) 987 * fixed EAPOL-Start processing to trigger WPA reauthentication 988 (previously, only EAPOL authentication was done) 989 9902005-01-02 - v0.3.3 991 * added support for EAP-PEAP in the integrated EAP authenticator 992 * added support for EAP-GTC in the integrated EAP authenticator 993 * added support for configuring list of EAP methods for Phase 1 so that 994 the integrated EAP authenticator can, e.g., use the wildcard entry 995 for EAP-TLS and EAP-PEAP 996 * added support for EAP-TTLS in the integrated EAP authenticator 997 * added support for EAP-SIM in the integrated EAP authenticator 998 * added support for using hostapd as a RADIUS authentication server 999 with the integrated EAP authenticator taking care of EAP 1000 authentication (new hostapd.conf options: radius_server_clients and 1001 radius_server_auth_port); this is not included in default build; use 1002 CONFIG_RADIUS_SERVER=y in .config to include 1003 10042004-12-19 - v0.3.2 1005 * removed 'daemonize' configuration file option since it has not really 1006 been used at all for more than year 1007 * driver_madwifi: fixed group key setup and added get_ssid method 1008 * added support for EAP-MSCHAPv2 in the integrated EAP authenticator 1009 10102004-12-12 - v0.3.1 1011 * added support for integrated EAP-TLS authentication (new hostapd.conf 1012 variables: ca_cert, server_cert, private_key, private_key_passwd); 1013 this enabled dynamic keying (WPA2/WPA/IEEE 802.1X/WEP) without 1014 external RADIUS server 1015 * added support for reading PKCS#12 (PFX) files (as a replacement for 1016 PEM/DER) to get certificate and private key (CONFIG_PKCS12) 1017 10182004-12-05 - v0.3.0 (beginning of 0.3.x development releases) 1019 * added support for Acct-{Input,Output}-Gigawords 1020 * added support for Event-Timestamp (in RADIUS Accounting-Requests) 1021 * added support for RADIUS Authentication Client MIB (RFC2618) 1022 * added support for RADIUS Accounting Client MIB (RFC2620) 1023 * made EAP re-authentication period configurable (eap_reauth_period) 1024 * fixed EAPOL reauthentication to trigger WPA/WPA2 reauthentication 1025 * fixed EAPOL state machine to stop if STA is removed during 1026 eapol_sm_step(); this fixes at least one segfault triggering bug with 1027 IEEE 802.11i pre-authentication 1028 * added support for multiple WPA pre-shared keys (e.g., one for each 1029 client MAC address or keys shared by a group of clients); 1030 new hostapd.conf field wpa_psk_file for setting path to a text file 1031 containing PSKs, see hostapd.wpa_psk for an example 1032 * added support for multiple driver interfaces to allow hostapd to be 1033 used with other drivers 1034 * added wired authenticator driver interface (driver=wired in 1035 hostapd.conf, see wired.conf for example configuration) 1036 * added madwifi driver interface (driver=madwifi in hostapd.conf, see 1037 madwifi.conf for example configuration; Note: include files from 1038 madwifi project is needed for building and a configuration file, 1039 .config, needs to be created in hostapd directory with 1040 CONFIG_DRIVER_MADWIFI=y to include this driver interface in hostapd 1041 build) 1042 * fixed an alignment issue that could cause SHA-1 to fail on some 1043 platforms (e.g., Intel ixp425 with a compiler that does not 32-bit 1044 align variables) 1045 * fixed RADIUS reconnection after an error in sending interim 1046 accounting packets 1047 * added hostapd control interface for external programs and an example 1048 CLI, hostapd_cli (like wpa_cli for wpa_supplicant) 1049 * started adding dot11, dot1x, radius MIBs ('hostapd_cli mib', 1050 'hostapd_cli sta <addr>') 1051 * finished update from IEEE 802.1X-2001 to IEEE 802.1X-REV (now d11) 1052 * added support for strict GTK rekeying (wpa_strict_rekey in 1053 hostapd.conf) 1054 * updated IAPP to use UDP port 3517 and multicast address 224.0.1.178 1055 (instead of broadcast) for IAPP ADD-notify (moved from draft 3 to 1056 IEEE 802.11F-2003) 1057 * added Prism54 driver interface (driver=prism54 in hostapd.conf; 1058 note: .config needs to be created in hostapd directory with 1059 CONFIG_DRIVER_PRISM54=y to include this driver interface in hostapd 1060 build) 1061 * dual-licensed hostapd (GPLv2 and BSD licenses) 1062 * fixed RADIUS accounting to generate a new session id for cases where 1063 a station reassociates without first being complete deauthenticated 1064 * fixed STA disassociation handler to mark next timeout state to 1065 deauthenticate the station, i.e., skip long wait for inactivity poll 1066 and extra disassociation, if the STA disassociates without 1067 deauthenticating 1068 * added integrated EAP authenticator that can be used instead of 1069 external RADIUS authentication server; currently, only EAP-MD5 is 1070 supported, so this cannot yet be used for key distribution; the EAP 1071 method interface is generic, though, so adding new EAP methods should 1072 be straightforward; new hostapd.conf variables: 'eap_authenticator' 1073 and 'eap_user_file'; this obsoletes "minimal authentication server" 1074 ('minimal_eap' in hostapd.conf) which is now removed 1075 * added support for FreeBSD and driver interface for the BSD net80211 1076 layer (driver=bsd in hostapd.conf and CONFIG_DRIVER_BSD=y in 1077 .config); please note that some of the required kernel mods have not 1078 yet been committed 1079 10802004-07-17 - v0.2.4 (beginning of 0.2.x stable releases) 1081 * fixed some accounting cases where Accounting-Start was sent when 1082 IEEE 802.1X port was being deauthorized 1083 10842004-06-20 - v0.2.3 1085 * modified RADIUS client to re-connect the socket in case of certain 1086 error codes that are generated when a network interface state is 1087 changes (e.g., when IP address changes or the interface is set UP) 1088 * fixed couple of cases where EAPOL state for a station was freed 1089 twice causing a segfault for hostapd 1090 * fixed couple of bugs in processing WPA deauthentication (freed data 1091 was used) 1092 10932004-05-31 - v0.2.2 1094 * fixed WPA/WPA2 group rekeying to use key index correctly (GN/GM) 1095 * fixed group rekeying to send zero TSC in EAPOL-Key messages to fix 1096 cases where STAs dropped multicast frames as replay attacks 1097 * added support for copying RADIUS Attribute 'Class' from 1098 authentication messages into accounting messages 1099 * send canned EAP failure if RADIUS server sends Access-Reject without 1100 EAP message (previously, Supplicant was not notified in this case) 1101 * fixed mixed WPA-PSK and WPA-EAP mode to work with WPA-PSK (i.e., do 1102 not start EAPOL state machines if the STA selected to use WPA-PSK) 1103 11042004-05-06 - v0.2.1 1105 * added WPA and IEEE 802.11i/RSN (WPA2) Authenticator functionality 1106 - based on IEEE 802.11i/D10.0 but modified to interoperate with WPA 1107 (i.e., IEEE 802.11i/D3.0) 1108 - supports WPA-only, RSN-only, and mixed WPA/RSN mode 1109 - both WPA-PSK and WPA-RADIUS/EAP are supported 1110 - PMKSA caching and pre-authentication 1111 - new hostapd.conf variables: wpa, wpa_psk, wpa_passphrase, 1112 wpa_key_mgmt, wpa_pairwise, wpa_group_rekey, wpa_gmk_rekey, 1113 rsn_preauth, rsn_preauth_interfaces 1114 * fixed interim accounting to remove any pending accounting messages 1115 to the STA before sending a new one 1116 11172004-02-15 - v0.2.0 1118 * added support for Acct-Interim-Interval: 1119 - draft-ietf-radius-acct-interim-01.txt 1120 - use Acct-Interim-Interval attribute from Access-Accept if local 1121 'radius_acct_interim_interval' is not set 1122 - allow different update intervals for each STA 1123 * fixed event loop to call signal handlers only after returning from 1124 the real signal handler 1125 * reset sta->timeout_next after successful association to make sure 1126 that the previously registered inactivity timer will not remove the 1127 STA immediately (e.g., if STA deauthenticates and re-associates 1128 before the timer is triggered). 1129 * added new hostapd.conf variable, nas_identifier, that can be used to 1130 add an optional RADIUS Attribute, NAS-Identifier, into authentication 1131 and accounting messages 1132 * added support for Accounting-On and Accounting-Off messages 1133 * fixed accounting session handling to send Accounting-Start only once 1134 per session and not to send Accounting-Stop if the session was not 1135 initialized properly 1136 * fixed Accounting-Stop statistics in cases where the message was 1137 previously sent after the kernel entry for the STA (and/or IEEE 1138 802.1X data) was removed 1139 1140 1141Note: 1142 1143Older changes up to and including v0.1.0 are included in the ChangeLog 1144of the Host AP driver. 1145