1 /* 2 * refclock_as2201 - clock driver for the Austron 2201A GPS 3 * Timing Receiver 4 */ 5 #ifdef HAVE_CONFIG_H 6 #include <config.h> 7 #endif 8 9 #if defined(REFCLOCK) && defined(CLOCK_AS2201) 10 11 #include "ntpd.h" 12 #include "ntp_io.h" 13 #include "ntp_refclock.h" 14 #include "ntp_unixtime.h" 15 #include "ntp_stdlib.h" 16 17 #include <stdio.h> 18 #include <ctype.h> 19 20 /* 21 * This driver supports the Austron 2200A/2201A GPS Receiver with 22 * Buffered RS-232-C Interface Module. Note that the original 2200/2201 23 * receivers will not work reliably with this driver, since the older 24 * design cannot accept input commands at any reasonable data rate. 25 * 26 * The program sends a "*toc\r" to the radio and expects a response of 27 * the form "yy:ddd:hh:mm:ss.mmm\r" where yy = year of century, ddd = 28 * day of year, hh:mm:ss = second of day and mmm = millisecond of 29 * second. Then, it sends statistics commands to the radio and expects 30 * a multi-line reply showing the corresponding statistics or other 31 * selected data. Statistics commands are sent in order as determined by 32 * a vector of commands; these might have to be changed with different 33 * radio options. If flag4 of the fudge configuration command is set to 34 * 1, the statistics data are written to the clockstats file for later 35 * processing. 36 * 37 * In order for this code to work, the radio must be placed in non- 38 * interactive mode using the "off" command and with a single <cr> 39 * response using the "term cr" command. The setting of the "echo" 40 * and "df" commands does not matter. The radio should select UTC 41 * timescale using the "ts utc" command. 42 * 43 * There are two modes of operation for this driver. The first with 44 * default configuration is used with stock kernels and serial-line 45 * drivers and works with almost any machine. In this mode the driver 46 * assumes the radio captures a timestamp upon receipt of the "*" that 47 * begins the driver query. Accuracies in this mode are in the order of 48 * a millisecond or two and the receiver can be connected to only one 49 * host. 50 * 51 * The second mode of operation can be used for SunOS kernels that have 52 * been modified with the ppsclock streams module included in this 53 * distribution. The mode is enabled if flag3 of the fudge configuration 54 * command has been set to 1. In this mode a precise timestamp is 55 * available using a gadget box and 1-pps signal from the receiver. This 56 * improves the accuracy to the order of a few tens of microseconds. In 57 * addition, the serial output and 1-pps signal can be bussed to more 58 * than one hosts, but only one of them should be connected to the 59 * radio input data line. 60 */ 61 62 /* 63 * GPS Definitions 64 */ 65 #define SMAX 200 /* statistics buffer length */ 66 #define DEVICE "/dev/gps%d" /* device name and unit */ 67 #define SPEED232 B9600 /* uart speed (9600 baud) */ 68 #define PRECISION (-20) /* precision assumed (about 1 us) */ 69 #define REFID "GPS\0" /* reference ID */ 70 #define DESCRIPTION "Austron 2201A GPS Receiver" /* WRU */ 71 72 #define LENTOC 19 /* yy:ddd:hh:mm:ss.mmm timecode lngth */ 73 74 /* 75 * AS2201 unit control structure. 76 */ 77 struct as2201unit { 78 char *lastptr; /* statistics buffer pointer */ 79 char stats[SMAX]; /* statistics buffer */ 80 int linect; /* count of lines remaining */ 81 int index; /* current statistics command */ 82 }; 83 84 /* 85 * Radio commands to extract statitistics 86 * 87 * A command consists of an ASCII string terminated by a <cr> (\r). The 88 * command list consist of a sequence of commands terminated by a null 89 * string ("\0"). One command from the list is sent immediately 90 * following each received timecode (*toc\r command) and the ASCII 91 * strings received from the radio are saved along with the timecode in 92 * the clockstats file. Subsequent commands are sent at each timecode, 93 * with the last one in the list followed by the first one. The data 94 * received from the radio consist of ASCII strings, each terminated by 95 * a <cr> (\r) character. The number of strings for each command is 96 * specified as the first line of output as an ASCII-encode number. Note 97 * that the ETF command requires the Input Buffer Module and the LORAN 98 * commands require the LORAN Assist Module. However, if these modules 99 * are not installed, the radio and this driver will continue to operate 100 * successfuly, but no data will be captured for these commands. 101 */ 102 static char stat_command[][30] = { 103 "ITF\r", /* internal time/frequency */ 104 "ETF\r", /* external time/frequency */ 105 "LORAN ENSEMBLE\r", /* GPS/LORAN ensemble statistics */ 106 "LORAN TDATA\r", /* LORAN signal data */ 107 "ID;OPT;VER\r", /* model; options; software version */ 108 109 "ITF\r", /* internal time/frequency */ 110 "ETF\r", /* external time/frequency */ 111 "LORAN ENSEMBLE\r", /* GPS/LORAN ensemble statistics */ 112 "TRSTAT\r", /* satellite tracking status */ 113 "POS;PPS;PPSOFF\r", /* position, pps source, offsets */ 114 115 "ITF\r", /* internal time/frequency */ 116 "ETF\r", /* external time/frequency */ 117 "LORAN ENSEMBLE\r", /* GPS/LORAN ensemble statistics */ 118 "LORAN TDATA\r", /* LORAN signal data */ 119 "UTC\r", /* UTC leap info */ 120 121 "ITF\r", /* internal time/frequency */ 122 "ETF\r", /* external time/frequency */ 123 "LORAN ENSEMBLE\r", /* GPS/LORAN ensemble statistics */ 124 "TRSTAT\r", /* satellite tracking status */ 125 "OSC;ET;TEMP\r", /* osc type; tune volts; oven temp */ 126 "\0" /* end of table */ 127 }; 128 129 /* 130 * Function prototypes 131 */ 132 static int as2201_start P((int, struct peer *)); 133 static void as2201_shutdown P((int, struct peer *)); 134 static void as2201_receive P((struct recvbuf *)); 135 static void as2201_poll P((int, struct peer *)); 136 137 /* 138 * Transfer vector 139 */ 140 struct refclock refclock_as2201 = { 141 as2201_start, /* start up driver */ 142 as2201_shutdown, /* shut down driver */ 143 as2201_poll, /* transmit poll message */ 144 noentry, /* not used (old as2201_control) */ 145 noentry, /* initialize driver (not used) */ 146 noentry, /* not used (old as2201_buginfo) */ 147 NOFLAGS /* not used */ 148 }; 149 150 151 /* 152 * as2201_start - open the devices and initialize data for processing 153 */ 154 static int 155 as2201_start( 156 int unit, 157 struct peer *peer 158 ) 159 { 160 register struct as2201unit *up; 161 struct refclockproc *pp; 162 int fd; 163 char gpsdev[20]; 164 165 /* 166 * Open serial port. Use CLK line discipline, if available. 167 */ 168 (void)sprintf(gpsdev, DEVICE, unit); 169 if (!(fd = refclock_open(gpsdev, SPEED232, LDISC_CLK))) 170 return (0); 171 172 /* 173 * Allocate and initialize unit structure 174 */ 175 if (!(up = (struct as2201unit *) 176 emalloc(sizeof(struct as2201unit)))) { 177 (void) close(fd); 178 return (0); 179 } 180 memset((char *)up, 0, sizeof(struct as2201unit)); 181 pp = peer->procptr; 182 pp->io.clock_recv = as2201_receive; 183 pp->io.srcclock = (caddr_t)peer; 184 pp->io.datalen = 0; 185 pp->io.fd = fd; 186 if (!io_addclock(&pp->io)) { 187 (void) close(fd); 188 free(up); 189 return (0); 190 } 191 pp->unitptr = (caddr_t)up; 192 193 /* 194 * Initialize miscellaneous variables 195 */ 196 peer->precision = PRECISION; 197 peer->burst = NSTAGE; 198 pp->clockdesc = DESCRIPTION; 199 memcpy((char *)&pp->refid, REFID, 4); 200 up->lastptr = up->stats; 201 up->index = 0; 202 return (1); 203 } 204 205 206 /* 207 * as2201_shutdown - shut down the clock 208 */ 209 static void 210 as2201_shutdown( 211 int unit, 212 struct peer *peer 213 ) 214 { 215 register struct as2201unit *up; 216 struct refclockproc *pp; 217 218 pp = peer->procptr; 219 up = (struct as2201unit *)pp->unitptr; 220 io_closeclock(&pp->io); 221 free(up); 222 } 223 224 225 /* 226 * as2201__receive - receive data from the serial interface 227 */ 228 static void 229 as2201_receive( 230 struct recvbuf *rbufp 231 ) 232 { 233 register struct as2201unit *up; 234 struct refclockproc *pp; 235 struct peer *peer; 236 l_fp trtmp; 237 238 /* 239 * Initialize pointers and read the timecode and timestamp. 240 */ 241 peer = (struct peer *)rbufp->recv_srcclock; 242 pp = peer->procptr; 243 up = (struct as2201unit *)pp->unitptr; 244 pp->lencode = refclock_gtlin(rbufp, pp->a_lastcode, BMAX, &trtmp); 245 #ifdef DEBUG 246 if (debug) 247 printf("gps: timecode %d %d %s\n", 248 up->linect, pp->lencode, pp->a_lastcode); 249 #endif 250 if (pp->lencode == 0) 251 return; 252 253 /* 254 * If linect is greater than zero, we must be in the middle of a 255 * statistics operation, so simply tack the received data at the 256 * end of the statistics string. If not, we could either have 257 * just received the timecode itself or a decimal number 258 * indicating the number of following lines of the statistics 259 * reply. In the former case, write the accumulated statistics 260 * data to the clockstats file and continue onward to process 261 * the timecode; in the later case, save the number of lines and 262 * quietly return. 263 */ 264 if (pp->sloppyclockflag & CLK_FLAG2) 265 pp->lastrec = trtmp; 266 if (up->linect > 0) { 267 up->linect--; 268 if ((int)(up->lastptr - up->stats + pp->lencode) > SMAX - 2) 269 return; 270 *up->lastptr++ = ' '; 271 (void)strcpy(up->lastptr, pp->a_lastcode); 272 up->lastptr += pp->lencode; 273 return; 274 } else { 275 if (pp->lencode == 1) { 276 up->linect = atoi(pp->a_lastcode); 277 return; 278 } else { 279 record_clock_stats(&peer->srcadr, up->stats); 280 #ifdef DEBUG 281 if (debug) 282 printf("gps: stat %s\n", up->stats); 283 #endif 284 } 285 } 286 up->lastptr = up->stats; 287 *up->lastptr = '\0'; 288 289 /* 290 * We get down to business, check the timecode format and decode 291 * its contents. If the timecode has invalid length or is not in 292 * proper format, we declare bad format and exit. 293 */ 294 if (pp->lencode < LENTOC) { 295 refclock_report(peer, CEVNT_BADREPLY); 296 return; 297 } 298 299 /* 300 * Timecode format: "yy:ddd:hh:mm:ss.mmm" 301 */ 302 if (sscanf(pp->a_lastcode, "%2d:%3d:%2d:%2d:%2d.%3d", &pp->year, 303 &pp->day, &pp->hour, &pp->minute, &pp->second, &pp->msec) 304 != 6) { 305 refclock_report(peer, CEVNT_BADREPLY); 306 return; 307 } 308 309 /* 310 * Test for synchronization (this is a temporary crock). 311 */ 312 if (pp->a_lastcode[2] != ':') 313 pp->leap = LEAP_NOTINSYNC; 314 else 315 pp->leap = LEAP_NOWARNING; 316 317 /* 318 * Process the new sample in the median filter and determine the 319 * timecode timestamp. 320 */ 321 if (!refclock_process(pp)) { 322 refclock_report(peer, CEVNT_BADTIME); 323 return; 324 } 325 326 /* 327 * If CLK_FLAG4 is set, initialize the statistics buffer and 328 * send the next command. If not, simply write the timecode to 329 * the clockstats file. 330 */ 331 (void)strcpy(up->lastptr, pp->a_lastcode); 332 up->lastptr += pp->lencode; 333 if (pp->sloppyclockflag & CLK_FLAG4) { 334 *up->lastptr++ = ' '; 335 (void)strcpy(up->lastptr, stat_command[up->index]); 336 up->lastptr += strlen(stat_command[up->index]); 337 up->lastptr--; 338 *up->lastptr = '\0'; 339 (void)write(pp->io.fd, stat_command[up->index], 340 strlen(stat_command[up->index])); 341 up->index++; 342 if (*stat_command[up->index] == '\0') 343 up->index = 0; 344 } 345 } 346 347 348 /* 349 * as2201_poll - called by the transmit procedure 350 * 351 * We go to great pains to avoid changing state here, since there may be 352 * more than one eavesdropper receiving the same timecode. 353 */ 354 static void 355 as2201_poll( 356 int unit, 357 struct peer *peer 358 ) 359 { 360 struct refclockproc *pp; 361 362 /* 363 * Send a "\r*toc\r" to get things going. We go to great pains 364 * to avoid changing state, since there may be more than one 365 * eavesdropper watching the radio. 366 */ 367 pp = peer->procptr; 368 if (write(pp->io.fd, "\r*toc\r", 6) != 6) { 369 refclock_report(peer, CEVNT_FAULT); 370 } else { 371 pp->polls++; 372 if (!(pp->sloppyclockflag & CLK_FLAG2)) 373 get_systime(&pp->lastrec); 374 } 375 if (peer->burst > 0) 376 return; 377 if (pp->coderecv == pp->codeproc) { 378 refclock_report(peer, CEVNT_TIMEOUT); 379 return; 380 } 381 refclock_receive(peer); 382 peer->burst = NSTAGE; 383 } 384 385 #else 386 int refclock_as2201_bs; 387 #endif /* REFCLOCK */ 388