Home
last modified time | relevance | path

Searched full:rise (Results 1 – 25 of 79) sorted by relevance

1234

/linux/drivers/gpu/drm/panel/
H A Dpanel-feiyang-fy07024di26a30d.c58 /* T1 (dvdd start + dvdd rise) 0 < T1 <= 10ms */ in feiyang_prepare()
65 /* T3 (dvdd rise + avdd start + avdd rise) T3 >= 20ms */ in feiyang_prepare()
71 * T5 + T6 (avdd rise + video & logic signal rise) in feiyang_prepare()
78 /* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ in feiyang_prepare()
98 /* T12 (video & logic signal rise + backlight rise) T12 >= 200ms */ in feiyang_enable()
131 /* T11 (dvdd rise to fall) 0 < T11 <= 10ms */ in feiyang_unprepare()
/linux/Documentation/devicetree/bindings/sound/
H A Dcirrus,cs42l42.yaml75 cirrus,ts-dbnc-rise:
162 If present this sets the rate that the HS bias should rise and fall.
163 The actual rise and fall times depend on external hardware (the
164 datasheet gives several rise and fall time examples).
166 0 - Fast rise time; slow, load-dependent fall time
219 cirrus,ts-dbnc-rise = <CS42L42_TS_DBNCE_1000>;
/linux/Documentation/devicetree/bindings/phy/
H A Dfsl,imx8mq-usb-phy.yaml54 fsl,phy-tx-rise-tune-percent:
56 Adjusts the rise/fall time duration of the HS waveform relative to
128 fsl,phy-tx-rise-tune-percent:
H A Dphy-stm32-usbphyc.yaml119 description: Enables the FS rise/fall tuning option
123 description: Enables the HS rise/fall reduction feature
/linux/Documentation/devicetree/bindings/usb/
H A Dchipidea,usb2-imx.yaml124 fsl,picophy-rise-fall-time-adjust:
126 HS Transmitter Rise/Fall Time Adjustment. Adjust the rise/fall times
127 of the high-speed transmitter waveform. It has no unit. The rise/fall
/linux/Documentation/leds/
H A Dleds-sc27xx.rst12 hardware pattern, which is used to configure the rise time,
17 format, we should set brightness as 0 for rise stage, fall
H A Dleds-cht-wcove.rst27 The rise and fall times must be the same value.
/linux/Documentation/devicetree/bindings/i2c/
H A Di2c-mux-ltc4306.txt24 - ltc,downstream-accelerators-enable: Enables the rise time accelerators
26 - ltc,upstream-accelerators-enable: Enables the rise time accelerators
H A Di2c-rk3x.yaml89 Number of nanoseconds the SCL signal takes to rise
H A Drenesas,rcar-i2c.yaml108 Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C
/linux/Documentation/devicetree/bindings/memory-controllers/
H A Dmvebu-devbus.txt92 address and data to DEV_WEn rise.
100 data after DEV_WEn rise.
/linux/drivers/leds/
H A Dleds-sc27xx-bltc.c157 /* Reset the rise, high, fall and low time to zero. */ in sc27xx_led_pattern_clear()
183 * Must contain 4 tuples to configure the rise time, high time, fall in sc27xx_led_pattern_set()
/linux/Documentation/devicetree/bindings/watchdog/
H A Dstarfive,jh7100-wdt.yaml17 output(WDOGINT) will rise when counter is 0. The counter will reload
/linux/drivers/gpu/drm/kmb/
H A Dkmb_dsi.c826 /* Typical rise/fall time=166, refer Table 1207 databook, in set_test_mode_src_osc_freq_target_low_bits()
843 /* Typical rise/fall time=166, refer Table 1207 databook, in set_test_mode_src_osc_freq_target_hi_bits()
1016 * typical rise/fall times: 166 ps in set_slewrate_gt_1000()
1032 * typical rise/fall time=166, refer Table 1207 databook in set_slewrate_gt_1000()
1039 * Typical rise/fall time=166, refer Table 1207 databook in set_slewrate_gt_1000()
1053 * - typical rise/fall times: 225 ps in set_slewrate_lt_1000()
1066 /* Typical rise/fall time=255, refer Table 1207 databook */ in set_slewrate_lt_1000()
/linux/arch/arm64/boot/dts/rockchip/
H A Dpx30-ringneck.dtsi413 * Hardware CS has a very slow rise time of about 6us,
415 * With cs-gpios we have a rise time of about 20ns.
/linux/Documentation/ABI/testing/
H A Dsysfs-class-led-driver-lm353327 Set the pattern generator fall and rise times (0..7), where:
/linux/drivers/usb/chipidea/
H A Dotg_fsm.h17 /* Wait for VBUS Rise */
/linux/drivers/input/misc/
H A Drk805-pwrkey.c77 dev_err(&pdev->dev, "Can't register rise irq: %d\n", err); in rk805_pwrkey_probe()
/linux/drivers/gpu/drm/mediatek/
H A Dmtk_hdmi_ddc_v2.c83 /* If down, rise bus for write operation */ in mtk_ddcm_write_hdmi()
120 /* The I2C bus might be down after WR operation: rise it again */ in mtk_ddcm_write_hdmi()
/linux/Documentation/filesystems/
H A Dlocks.rst35 for example. This gave rise to some other subtle problems if sendmail was
/linux/include/linux/
H A Dled-lm3530.h89 * @brt_ramp_rise: rate of rise of led current
/linux/drivers/gpu/drm/i915/gt/
H A Dselftest_slpc.c393 /* Actual frequency should rise above min */ in run_test()
395 pr_err("Actual freq did not rise above min\n"); in run_test()
/linux/drivers/pinctrl/
H A Dpinctrl-at91.h59 #define PIO_FRLHSR 0xd8 /* Fall/Rise - Low/High Status Register */
/linux/drivers/char/
H A Dnsc_gpio.c36 (config & 32) ? "HI" : "LO", /* trigger on rise/fall edge */ in nsc_gpio_dump()
/linux/Documentation/driver-api/gpio/
H A Dintro.rst108 value (after the appropriate rise time passes), you know some other component is

1234