| /freebsd/sys/contrib/device-tree/Bindings/iio/ |
| H A D | st,st-sensors.yaml | 99 description: interrupt line(s) connected to the DRDY line(s) and/or the
101 three interrupts, and the DRDY must be the first one if it exists on
111 st,drdy-int-pin:
137 st,drdy-int-pin: false
144 # These have only DRDY
162 st,drdy-int-pin: false
180 st,drdy-int-pin = <1>;
194 st,drdy-int-pin = <2>;
|
| H A D | st-sensors.txt | 16 - st,drdy-int-pin: the pin on the package that will be used to signal
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/accel/ |
| H A D | adi,adxl355.yaml | 31 Type for DRDY should be IRQ_TYPE_EDGE_RISING.
40 - DRDY
73 interrupt-names = "DRDY";
89 interrupt-names = "DRDY";
|
| /freebsd/sys/contrib/device-tree/src/arm/st/ |
| H A D | ste-href-tvk1281618-r2.dtsi | 89 st,drdy-int-pin = <1>;
99 * cannot set its DRDY line to open drain, so it cannot be
120 * cannot set its DRDY line to open drain, so it cannot be
132 st,drdy-int-pin = <1>;
157 * cannot set its DRDY line to open drain, so it cannot be
169 st,drdy-int-pin = <2>;
271 /* GPIO 32 used for DRDY, pull this down */
|
| H A D | ste-snowball.dts | 354 st,drdy-int-pin = <1>;
373 interrupts = <5 IRQ_TYPE_EDGE_RISING>; /* DRDY line */
378 st,drdy-int-pin = <2>;
385 interrupts = <6 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
605 "GPIO166_A22", /* DRDY */
|
| H A D | ste-href-tvk1281618-r3.dtsi | 83 st,drdy-int-pin = <1>;
197 /* GPIO 32 used for DRDY, pull this down */
|
| H A D | ste-href-stuib.dtsi | 80 st,drdy-int-pin = <1>;
|
| H A D | stm32f429-disco.dts | 185 st,drdy-int-pin = <2>;
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/magnetometer/ |
| H A D | ak8974.txt | 16 - interrupts: data ready (DRDY) and interrupt (INT1) lines
17 from the chip, the DRDY interrupt must be placed first.
|
| H A D | asahi-kasei,ak8974.yaml | 25 Data ready (DRDY) and interrupt (INT1) lines from the chip. The DRDY
|
| H A D | asahi-kasei,ak8975.yaml | 35 AK8975 has a "Data ready" pin (DRDY) which informs that data
41 description: interrupt for DRDY pin. Triggered on rising edge.
|
| H A D | hmc5843.txt | 14 - gpios : should be device tree identifier of the magnetometer DRDY pin
|
| H A D | pni,rm3100.txt | 10 - interrupts: data ready (DRDY) from the chip.
|
| H A D | ak8975.txt | 10 - gpios : should be device tree identifier of the magnetometer DRDY pin
|
| /freebsd/sys/contrib/device-tree/src/arm64/allwinner/ |
| H A D | sun50i-a64-pinephone-1.2.dts | 40 * Board revision 1.2 fixed routing of the interrupt to DRDY pin,
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/imu/ |
| H A D | st_lsm6dsx.txt | 22 - st,drdy-int-pin: the pin on the package that will be used to signal
|
| H A D | st,lsm6dsx.yaml | 68 st,drdy-int-pin:
|
| /freebsd/sys/contrib/device-tree/src/arm/ti/omap/ |
| H A D | am335x-sancloud-bbe.dts | 38 st,drdy-int-pin = <1>;
|
| /freebsd/sys/contrib/device-tree/src/arm64/qcom/ |
| H A D | msm8916-samsung-gt5-common.dtsi | 89 st,drdy-int-pin = <1>;
|
| /freebsd/sys/contrib/device-tree/src/arm64/freescale/ |
| H A D | imx8mm-venice-gw71xx.dtsi | 96 st,drdy-int-pin = <1>;
|
| H A D | imx8mm-venice-gw72xx.dtsi | 125 st,drdy-int-pin = <1>;
|
| H A D | imx8mm-venice-gw73xx.dtsi | 145 st,drdy-int-pin = <1>;
|
| /freebsd/sys/dev/ic/ |
| H A D | nec765.h | 82 #define NE7_ST3BITS "\020\010fault\007write_protect\006drdy\005tk0\004two_side\003side_sel\002"
|
| /freebsd/usr.sbin/bhyve/amd64/ |
| H A D | pci_gvt-d-opregion.h | 64 uint32_t drdy; ///< Offset 0x100 Driver Readiness member
|
| /freebsd/sys/contrib/device-tree/src/arm/nxp/imx/ |
| H A D | imx6qdl-gw5912.dtsi | 307 st,drdy-int-pin = <1>;
|