| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | app-pri.rst | 13 applications from changing video controls or switching the current TV
29 Ioctls changing driver properties, such as
|
| /linux/Documentation/userspace-api/media/rc/ |
| H A D | lirc-get-features.rst | 81 The driver supports changing the modulation frequency via
88 The driver supports changing the duty cycle using
95 The driver supports changing the active transmitter(s) using
|
| H A D | rc-table-change.rst | 10 /dev/input/event device, to allow changing the default keymapping.
|
| /linux/security/integrity/evm/ |
| H A D | Kconfig | 27 WARNING: changing the HMAC calculation method or adding
44 WARNING: changing the HMAC calculation method or adding
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-iio-bno055 | 7 the scale (which should be used when changing the maximum and
16 changing the maximum and minimum readable value affects also the
|
| H A D | sysfs-class-leds-gt683r | 6 Set the mode of LEDs. You should notice that changing the mode
|
| H A D | sysfs-bus-iio-isl29501 | 25 measurements due to changing temperature and ambient
|
| H A D | sysfs-bus-iio-dac-ltc2688 | 6 for changing the dither parameters. They way it should be done is:
|
| /linux/Documentation/networking/device_drivers/fddi/ |
| H A D | defza.rst | 40 doesn't support changing them individually.
50 5. MAC address change. The card does not support changing the Media
|
| /linux/Documentation/userspace-api/ebpf/ |
| H A D | index.rst | 7 Linux kernel for runtime extension and instrumentation without changing kernel
|
| /linux/Documentation/i2c/busses/ |
| H A D | i2c-ismt.rst | 18 Allows changing of the bus speed. Normally, the bus speed is set by the BIOS
|
| /linux/drivers/memory/samsung/ |
| H A D | Kconfig | 19 Frequency Scaling in DMC and DRAM. It also supports changing timings
|
| /linux/Documentation/networking/device_drivers/ethernet/marvell/ |
| H A D | octeon_ep.rst | 35 Network Interface control like changing mtu, link speed, link down/up are
|
| /linux/Documentation/networking/ |
| H A D | ip_dynaddr.rst | 8 dynamically changing packet source address (and socket's if local procs).
|
| /linux/Documentation/RCU/ |
| H A D | rcuref.rst | 47 If this list/array is made lock free using RCU as in changing the
48 write_lock() in add() and delete() to spin_lock() and changing read_lock()
|
| /linux/drivers/ntb/hw/idt/ |
| H A D | Kconfig | 12 by BIOS using slave-SMBus interface changing corresponding registers
|
| /linux/arch/arm64/boot/dts/freescale/ |
| H A D | s32g274a-rdb2.dts | 74 * If the property is removed without changing the resistor position,
|
| /linux/Documentation/process/ |
| H A D | maintainer-kvm-x86.rst | 140 and APM are constantly changing, and so the numbers/labels aren't stable.
206 find. Changelogs that bury the "what's actually changing" in a one-liner after
216 Another benefit of stating "what's changing" first is that it's almost always
217 possible to state "what's changing" in a single sentence. Conversely, all but
219 the problem. If both the "what's changing" and "what's the bug" are super
221 "what's changing), then covering the shorter one first is advantageous because
224 painful than having to skip three paragraphs to get to "what's changing".
|
| /linux/Documentation/fb/ |
| H A D | cirrusfb.rst | 48 * Hint for AXP: Use -accel false -vyres -1 when changing resolution
|
| /linux/Documentation/userspace-api/gpio/ |
| H A D | gpio-v2-line-set-config-ioctl.rst | 47 The motivating use case for this command is changing direction of
|
| H A D | gpio-handle-set-config-ioctl.rst | 51 The motivating use case for this command is changing direction of
|
| /linux/arch/arm/boot/dts/marvell/ |
| H A D | kirkwood-openrd.dtsi | 84 * When changing this line make sure the newly
|
| /linux/Documentation/devicetree/bindings/mtd/ |
| H A D | gpio-control-nand.txt | 24 the GPIO's and the NAND flash data bus. If present, then after changing
|
| /linux/Documentation/features/sched/membarrier-sync-core/ |
| H A D | arch-support.txt | 41 # after changing the current mm, and deal with the special case of kthread ->
|
| /linux/Documentation/driver-api/soundwire/ |
| H A D | locking.rst | 20 - Addition and removal of Slave(s), changing Slave status.
|