| /linux/Documentation/networking/device_drivers/can/freescale/ |
| H A D | flexcan.rst | 52 ip link set dev can0 down
53 ethtool --set-priv-flags can0 rx-rtr {off|on}
54 ip link set dev can0 up
|
| /linux/Documentation/ABI/testing/ |
| H A D | sysfs-platform-at91 | 23 echo 0x7ff > /sys/class/net/can0/mb0_id
27 echo 0x9fffffff > /sys/class/net/can0/mb0_id
|
| /linux/arch/arm/boot/dts/microchip/ |
| H A D | at91sam9x5_can.dtsi | 15 can0: can@f8000000 { label
38 can0 {
|
| H A D | sama5d3_can.dtsi | 16 can0 {
34 can0: can@f000c000 { label
|
| H A D | lan966x-pcb8291.dts | 67 can0_b_pins: can0-b-pins {
80 &can0 {
|
| H A D | at91-sam9x60_curiosity.dts | 110 &can0 {
125 status = "okay"; /* Conflict with can0. */
266 can0 {
267 pinctrl_can0_rx_tx: can0-rx-tx {
|
| H A D | sama5d36ek_cmp.dts | 25 can0: can@f000c000 { label
|
| H A D | sama5d36ek.dts | 29 can0: can@f000c000 { label
|
| H A D | sama5d35ek.dts | 24 can0: can@f000c000 { label
|
| /linux/Documentation/devicetree/bindings/reset/ |
| H A D | zynq-reset.txt | 45 256: can0 reset
47 258: can0 ref reset
|
| /linux/arch/arm64/boot/dts/renesas/ |
| H A D | rzg2ul-smarc-pinfunction.dtsi | 15 can0_pins: can0 {
21 can0-stb-hog {
|
| H A D | rzg2l-smarc-pinfunction.dtsi | 15 can0_pins: can0 {
21 can0-stb-hog {
|
| H A D | r9a07g043-smarc-pmod.dtso | 27 can0-stb-hog {
|
| /linux/arch/powerpc/boot/dts/fsl/ |
| H A D | p1010si-pre.dtsi | 53 can0 = &can0;
|
| /linux/arch/mips/boot/dts/mobileye/ |
| H A D | eyeq5-pins.dtsi | 45 can0_pins: can0-pins {
46 function = "can0";
|
| /linux/arch/arm/boot/dts/st/ |
| H A D | spear320-evb.dts | 60 can0 {
62 st,function = "can0";
|
| H A D | spear320-hmi.dts | 64 can0 {
66 st,function = "can0";
|
| /linux/arch/arm/boot/dts/renesas/ |
| H A D | r8a7792-blanche.dts | 260 can0_pins: can0 {
262 function = "can0";
316 &can0 {
|
| H A D | r8a7792-wheat.dts | 147 can0_pins: can0 {
149 function = "can0";
191 &can0 {
|
| H A D | r8a7742-iwg21d-q7-dbcm-ca.dts | 73 &can0 {
132 can0_pins: can0 {
134 function = "can0";
|
| /linux/Documentation/devicetree/bindings/clock/ |
| H A D | zynq-7000.txt | 60 19: can0
99 "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
|
| /linux/arch/arm/boot/dts/xilinx/ |
| H A D | zynq-zc702.dts | 69 &can0 {
193 pinctrl_can0_default: can0-default {
195 function = "can0";
|
| /linux/Documentation/devicetree/bindings/net/can/ |
| H A D | holt_hi311x.txt | 15 can0: can@1 {
|
| /linux/arch/arm/boot/dts/allwinner/ |
| H A D | sun7i-a20-linutronix-testbox-v2.dts | 43 &can0 {
|
| /linux/drivers/clk/mxs/ |
| H A D | clk-imx28.c | 141 fec, can0, can1, usb0, usb1, usb0_phy, usb1_phy, enet_out, enumerator
225 clks[can0] = mxs_clk_gate("can0", "ref_xtal", FLEXCAN, 30); in mx28_clocks_init()
|