| /linux/drivers/net/ethernet/oki-semi/pch_gbe/ |
| H A D | pch_gbe_param.c | 153 { SPEED_10, "" },
328 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
339 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
351 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
354 case SPEED_10: in pch_gbe_check_copper_options()
362 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
365 case SPEED_10 + HALF_DUPLEX: in pch_gbe_check_copper_options()
369 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
372 case SPEED_10 + FULL_DUPLEX: in pch_gbe_check_copper_options()
376 hw->mac.link_speed = SPEED_10; in pch_gbe_check_copper_options()
|
| /linux/drivers/net/ethernet/ibm/emac/ |
| H A D | phy.c | 115 phy->speed = SPEED_10; in genmii_setup_aneg()
188 case SPEED_10: in genmii_setup_forced()
239 phy->speed = SPEED_10; in genmii_read_link()
272 phy->speed = SPEED_10; in genmii_read_link()
519 phy->speed = SPEED_10; in emac_mii_phy_probe()
|
| /linux/drivers/net/ethernet/chelsio/cxgb3/ |
| H A D | vsc8211.c | 161 sp = SPEED_10; in vsc8211_get_link_status()
171 sp = SPEED_10; in vsc8211_get_link_status()
237 sp = SPEED_10; in vsc8211_get_link_status_fiber()
|
| H A D | aq100x.c | 239 *speed = SPEED_10; in aq100x_get_link_status()
|
| /linux/drivers/net/ethernet/intel/e1000/ |
| H A D | e1000_param.c | 544 { SPEED_10, "" }, in e1000_check_copper_options()
666 case SPEED_10: in e1000_check_copper_options()
673 case SPEED_10 + HALF_DUPLEX: in e1000_check_copper_options()
679 case SPEED_10 + FULL_DUPLEX: in e1000_check_copper_options()
|
| /linux/drivers/net/ethernet/intel/igbvf/ |
| H A D | defines.h | 53 #define SPEED_10 10 macro
|
| /linux/drivers/net/ethernet/microchip/sparx5/ |
| H A D | sparx5_port.c | 39 status->speed = SPEED_10; in decode_sgmii_word()
248 conf->speed != SPEED_10 && in sparx5_port_verify_speed()
266 conf->speed != SPEED_10) in sparx5_port_verify_speed()
381 spd_prm = spd == SPEED_10 ? 1000 : spd == SPEED_100 ? 100 : 10; in sparx5_port_disable()
515 case SPEED_10: in sparx5_port_fifo_sz()
621 case SPEED_10: in sparx5_port_fwd_urg()
893 clk_spd = spd == SPEED_10 ? 0 : spd == SPEED_100 ? 1 : 2; in sparx5_port_config_low_set()
|
| /linux/drivers/net/ethernet/ibm/ehea/ |
| H A D | ehea_ethtool.c | 36 speed = SPEED_10; in ehea_get_link_ksettings()
97 case SPEED_10: in ehea_set_link_ksettings()
|
| /linux/drivers/net/ethernet/stmicro/stmmac/ |
| H A D | dwmac-meson.c | 34 case SPEED_10: in meson6_dwmac_set_clk_tx_rate()
|
| /linux/drivers/net/ethernet/atheros/alx/ |
| H A D | hw.h | 577 if (speed == SPEED_10 && duplex == DUPLEX_FULL) in alx_speed_to_ethadv()
579 if (speed == SPEED_10 && duplex == DUPLEX_HALF) in alx_speed_to_ethadv()
|
| /linux/drivers/net/ethernet/apm/xgene-v2/ |
| H A D | mac.c | 32 case SPEED_10: in xge_mac_set_speed()
|
| /linux/drivers/net/ethernet/ti/icssg/ |
| H A D | icssg_mii_cfg.c | 59 if (emac->speed == SPEED_10 && phy_interface_mode_is_rgmii(emac->phy_if)) in icssg_update_rgmii_cfg()
|
| /linux/drivers/net/dsa/mv88e6xxx/ |
| H A D | pcs-6185.c | 89 state->speed = SPEED_10; in mv88e6185_pcs_get_state()
|
| /linux/drivers/net/ethernet/freescale/enetc/ |
| H A D | enetc4_pf.c | 659 case SPEED_10: in enetc4_set_port_speed()
661 val |= (PCR_PSPEED & PCR_PSPEED_VAL(SPEED_10)); in enetc4_set_port_speed()
683 case SPEED_10: in enetc4_set_rgmii_mac()
708 case SPEED_10: in enetc4_set_rmii_mac()
|
| /linux/drivers/net/ethernet/atheros/atlx/ |
| H A D | atlx.h | 24 #define SPEED_10 10 macro
|
| /linux/drivers/net/ethernet/apm/xgene/ |
| H A D | xgene_enet_sgmac.c | 192 p->phy_speed = SPEED_10; in xgene_enet_link_status()
249 case SPEED_10: in xgene_sgmac_set_speed()
|
| /linux/drivers/net/ethernet/broadcom/ |
| H A D | bgmac-platform.c | 141 case SPEED_10: in bgmac_nicpm_speed_set()
|
| /linux/drivers/net/dsa/b53/ |
| H A D | b53_serdes.c | 116 state->speed = SPEED_10; in b53_serdes_get_state()
|
| /linux/drivers/net/pcs/ |
| H A D | pcs-lynx.c | 229 case SPEED_10: in lynx_pcs_link_up_sgmii()
|
| H A D | pcs-mtk-lynxi.c | 275 if (speed == SPEED_10) in mtk_pcs_lynxi_link_up()
|
| H A D | pcs-xpcs.c | 363 case SPEED_10: in xpcs_link_up_usxgmii()
1083 state->speed = SPEED_10; in xpcs_get_state_c37_sgmii()
1104 state->speed = SPEED_10; in xpcs_get_state_c37_sgmii()
|
| /linux/drivers/net/ethernet/hisilicon/hibmcge/ |
| H A D | hbg_mdio.c | 171 case SPEED_10: in hbg_phy_adjust_link()
|
| /linux/drivers/net/ethernet/silan/ |
| H A D | sc92031.c | 1165 cmd->base.speed = (output_status & 0x2) ? SPEED_100 : SPEED_10; in sc92031_ethtool_get_link_ksettings()
1194 if (!(speed == SPEED_10 || speed == SPEED_100)) in sc92031_ethtool_set_link_ksettings()
1232 if (speed == SPEED_10) in sc92031_ethtool_set_link_ksettings()
|
| /linux/drivers/net/ethernet/atheros/atl1c/ |
| H A D | atl1c_hw.c | 698 *speed = SPEED_10; in atl1c_get_speed_and_duplex()
758 speed = SPEED_10; in atl1c_phy_to_ps_link()
|
| /linux/drivers/net/dsa/lantiq/ |
| H A D | mxl-gsw1xx.c | 191 state->speed = SPEED_10; in gsw1xx_pcs_get_state()
492 if (speed == SPEED_10) in gsw1xx_pcs_link_up()
|