Home
last modified time | relevance | path

Searched refs:LOW (Results 1 – 25 of 54) sorted by relevance

123

/linux/arch/arm64/boot/dts/rockchip/
H A Drk3588-jaguar-pre-ict-tester.dtso81 * LOW. The signal shall not read HIGH in the event
91 * the SoC default for this pin) so that LOW is read if
103 * LOW. This is an issue if GPIO3_B2 isn't properly
105 * default bias is pull-down therefore being LOW. So
109 * soldering reports LOW.
125 * on GPIO3_C6 or VCC_1V8_S0_1 reports LOW but proper
134 * the SoC default for this pin) so that LOW is read if
144 * the SoC default for this pin) so that LOW is read if
154 * the SoC default for this pin) so that LOW is read if
164 * the SoC default for this pin) so that LOW is read if
H A Drk3399-evb-ind.dts414 /* tshut polarity 0:LOW 1:HIGH */
/linux/lib/
H A Dtest_dynamic_debug.c78 enum cat_disjoint_names { LOW = 11, MID, HI }; enumerator
105 prdbg(LOW); in do_cats()
/linux/tools/power/cpupower/bench/
H A Dexample.cfg4 priority = LOW
H A DREADME-BENCH114 -p, --prio=<priority> scheduler priority, HIGH, LOW or DEFAULT
/linux/Documentation/devicetree/bindings/sound/
H A Dcs35l34.txt35 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel),
37 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right
/linux/arch/arm64/boot/dts/renesas/
H A Dhihope-rzg2-ex-lvds.dtsi20 * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
/linux/arch/arm64/boot/dts/freescale/
H A Dimx8x-colibri-iris-v2.dtsi32 /* 6B/8B mode. Select LOW - 8B mode (24bit) */
/linux/include/linux/mfd/
H A Dtps65010.h123 #define LOW 0 macro
/linux/Documentation/devicetree/bindings/mfd/
H A Dmax77620.txt54 When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz
99 event cleared (set to LOW) whether it
125 control) then, GPIO1/nRST_IO goes LOW.
/linux/drivers/s390/crypto/
H A Dzcrypt_msgtype6.h106 #define LOW 10 macro
/linux/arch/arm/boot/dts/amlogic/
H A Dmeson8b-ec100.dts65 * GPIOAO_7 (power LED, which has to go LOW as well).
77 * Needs to go LOW (together with the poweroff GPIO)
80 * the output to LOW signals the EC to start a
/linux/Documentation/userspace-api/media/cec/
H A Dcec-ioc-dqevent.rst153 * .. _`CEC-EVENT-PIN-CEC-LOW`:
167 * .. _`CEC-EVENT-PIN-HPD-LOW`:
185 * .. _`CEC-EVENT-PIN-5V-LOW`:
/linux/Documentation/devicetree/bindings/net/bluetooth/
H A Dmediatek,bluetooth.txt30 - boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when
/linux/Documentation/devicetree/bindings/pinctrl/
H A Dpinctrl-max77620.txt73 FPS input event set to LOW.
/linux/Documentation/driver-api/iio/
H A Dbuffers.rst57 |D3 |D2 |D1 |D0 | X | X | X | X | (LOW byte, address 0x06)
/linux/drivers/nfc/st95hf/
H A Dcore.c76 #define LOW 0 macro
459 gpiod_set_value(st95con->enable_gpiod, LOW); in st95hf_send_st95enable_negativepulse()
/linux/Documentation/wmi/devices/
H A Dalienware-wmi.rst250 | | | **LOW**: Disables DFU mode |
256 | | | **LOW**: MCU is OFF. |
/linux/arch/arm/boot/dts/renesas/
H A Dr8a7742-iwg21d-q7-dbcm-ca.dts96 /* Disable hogging GP0_18 to output LOW */
/linux/arch/arm/boot/dts/st/
H A Dste-href-ab8500.dtsi274 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
H A Dste-href-ab8505.dtsi274 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
/linux/arch/arm64/boot/dts/amlogic/
H A Dmeson-g12b-odroid-n2.dtsi29 /* Connected to the Hub CHIPENABLE, LOW sets low power state */
/linux/drivers/tty/vt/
H A Ducs_width_table.h_shipped28 { 0x06EA, 0x06ED }, /* ARABIC EMPTY CENTRE LOW STOP - ARABIC SMALL LOW MEEM */
230 { 0x10EFC, 0x10EFF }, /* ARABIC COMBINING ALEF OVERLAY - ARABIC SMALL LOW WORD MADDA */
315 { 0x16AF0, 0x16AF4 }, /* BASSA VAH COMBINING HIGH TONE - BASSA VAH COMBINING HIGH-LOW TONE */
/linux/Documentation/driver-api/gpio/
H A Dintro.rst97 **LOW**: ``gpiod_direction_output(gpio, 0)`` ... this drives the signal and
/linux/Documentation/devicetree/bindings/regulator/
H A Dregulator-max77620.txt71 FPS input event set to LOW.

123