| /freebsd/sys/contrib/dev/acpica/compiler/ |
| H A D | aslmapenter.c | 253 UINT32 Speed; in MpSaveSerialInfo() local
275 Speed = Resource->I2cSerialBus.ConnectionSpeed; in MpSaveSerialInfo()
281 Speed = Resource->SpiSerialBus.ConnectionSpeed; in MpSaveSerialInfo()
287 Speed = Resource->UartSerialBus.DefaultBaudRate; in MpSaveSerialInfo()
300 Info->Speed = Speed; in MpSaveSerialInfo()
|
| /freebsd/sys/contrib/device-tree/src/mips/brcm/ |
| H A D | bcm63268-comtrend-vr-3032u.dts | 31 /* GPHY0 Speed 0 */
37 /* GPHY0 Speed 1 */
87 /* EPHY0 Speed */
92 /* EPHY1 Speed */
97 /* EPHY2 Speed */
|
| /freebsd/sys/contrib/zstd/ |
| H A D | README.md | 67 Speed vs Compression trade-off is configurable by small increments.
78 Compression Speed vs Ratio | Decompression Speed
80 …ression Speed vs Ratio](doc/images/CSpeed2.png "Compression Speed vs Ratio") |  |  and NVHS (NVIDIA High
4 Speed) each interfacing with 12 and 8 P2U instances respectively.
|
| H A D | phy-stm32-usbphyc.txt | 3 The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI
|
| /freebsd/sys/contrib/device-tree/Bindings/i2c/ |
| H A D | i2c-exynos5.txt | 1 * Samsung's High Speed I2C controller
3 The Samsung's High Speed I2C controller is used to interface with I2C devices
|
| H A D | i2c-imx.txt | 1 * Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
|
| /freebsd/sys/contrib/device-tree/Bindings/usb/ |
| H A D | usb251xb.txt | 1 Microchip USB 2.0 Hi-Speed Hub Controller
4 Hi-Speed Controller.
26 - disable-hi-speed : disable USB Hi-Speed support (boolean)
|
| H A D | usb4604.txt | 1 SMSC USB4604 High-Speed Hub Controller
|
| H A D | samsung-hsotg.txt | 1 Samsung High Speed USB OTG controller
|
| H A D | usb3503.txt | 1 SMSC USB3503 High-Speed Hub Controller
|
| /freebsd/sys/contrib/device-tree/Bindings/serial/ |
| H A D | nxp-lpc32xx-hsuart.txt | 1 * NXP LPC32xx SoC High Speed UART
|
| /freebsd/sys/contrib/device-tree/src/arm64/bitmain/ |
| H A D | bm1880-sophon-edge.dts | 16 * LSEC = Low Speed External Connector
17 * HSEC = High Speed External Connector
|
| /freebsd/sys/contrib/device-tree/Bindings/powerpc/4xx/ |
| H A D | hsta.txt | 2 ppc476gtr High Speed Serial Assist (HSTA) node
|
| /freebsd/sys/contrib/device-tree/Bindings/spi/ |
| H A D | spi-bcm63xx-hsspi.txt | 1 Binding for Broadcom BCM6328 High Speed SPI controller
|
| /freebsd/sys/contrib/device-tree/Bindings/dma/ |
| H A D | mtk-hsdma.txt | 1 MediaTek High-Speed DMA Controller
|
| /freebsd/sys/contrib/zstd/programs/ |
| H A D | README.md | 256 Compression Speed vs Ratio | Decompression Speed
258 …Speed vs Ratio](https://raw.githubusercontent.com/facebook/zstd/v1.3.3/doc/images/ldmCspeed.png "C…
|
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | xilinx_gmii2rgmii.txt | 9 Speed of operation. This core can switch dynamically between the three
|
| /freebsd/sys/contrib/device-tree/Bindings/connector/ |
| H A D | samsung,usb-connector-11pin.txt | 19 0: High Speed (HS),
|
| /freebsd/share/misc/ |
| H A D | scsi_modes | 465 {Maximum Read Speed Supported (kBps)} i2
468 {Current Read Speed Selected (kBps)} i2
476 {Maximum Write Speed Supported (kBps)} i2
477 {Current Write Speed Supported (kBps)} i2
|
| /freebsd/sys/contrib/device-tree/Bindings/mmc/ |
| H A D | atmel-hsmci.txt | 1 * Atmel High Speed MultiMedia Card Interface
|
| /freebsd/sys/contrib/device-tree/src/arm64/actions/ |
| H A D | s900-bubblegum-96.dts | 72 * LSEC = Low Speed External Connector
73 * HSEC = High Speed External Connector
|
| /freebsd/sys/contrib/device-tree/src/arm64/amlogic/ |
| H A D | meson-g12b-gsking-x.dts | 26 /* Using Dummy Speed */
|
| /freebsd/sys/contrib/device-tree/src/arm64/hisilicon/ |
| H A D | hi3660-hikey960.dts | 155 ldo11: LDO11 { /* Low Speed Connector */
209 * LSEC = Low Speed External Connector
210 * HSEC = High Speed External Connector
|
| H A D | hi3798cv200-poplar.dts | 206 /* No optional LS-UART1 on Low Speed Expansion Connector. */
|