xref: /freebsd/sys/dev/igc/igc_defines.h (revision 33ed9bdca307bedb3d66a50ed7d4d7b4bf4acf39)
1 /*-
2  * Copyright 2021 Intel Corp
3  * Copyright 2021 Rubicon Communications, LLC (Netgate)
4  * SPDX-License-Identifier: BSD-3-Clause
5  */
6 
7 #ifndef _IGC_DEFINES_H_
8 #define _IGC_DEFINES_H_
9 
10 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
11 #define REQ_TX_DESCRIPTOR_MULTIPLE  8
12 #define REQ_RX_DESCRIPTOR_MULTIPLE  8
13 
14 /* Definitions for power management and wakeup registers */
15 /* Wake Up Control */
16 #define IGC_WUC_APME		0x00000001 /* APM Enable */
17 #define IGC_WUC_PME_EN	0x00000002 /* PME Enable */
18 #define IGC_WUC_PME_STATUS	0x00000004 /* PME Status */
19 #define IGC_WUC_APMPME	0x00000008 /* Assert PME on APM Wakeup */
20 #define IGC_WUC_PHY_WAKE	0x00000100 /* if PHY supports wakeup */
21 
22 /* Wake Up Filter Control */
23 #define IGC_WUFC_LNKC	0x00000001 /* Link Status Change Wakeup Enable */
24 #define IGC_WUFC_MAG	0x00000002 /* Magic Packet Wakeup Enable */
25 #define IGC_WUFC_EX	0x00000004 /* Directed Exact Wakeup Enable */
26 #define IGC_WUFC_MC	0x00000008 /* Directed Multicast Wakeup Enable */
27 #define IGC_WUFC_BC	0x00000010 /* Broadcast Wakeup Enable */
28 #define IGC_WUFC_ARP	0x00000020 /* ARP Request Packet Wakeup Enable */
29 #define IGC_WUFC_IPV4	0x00000040 /* Directed IPv4 Packet Wakeup Enable */
30 
31 /* Wake Up Status */
32 #define IGC_WUS_LNKC		IGC_WUFC_LNKC
33 #define IGC_WUS_MAG		IGC_WUFC_MAG
34 #define IGC_WUS_EX		IGC_WUFC_EX
35 #define IGC_WUS_MC		IGC_WUFC_MC
36 #define IGC_WUS_BC		IGC_WUFC_BC
37 
38 /* Packet types that are enabled for wake packet delivery */
39 #define WAKE_PKT_WUS ( \
40 	IGC_WUS_EX   | \
41 	IGC_WUS_ARPD | \
42 	IGC_WUS_IPV4 | \
43 	IGC_WUS_IPV6 | \
44 	IGC_WUS_NSD)
45 
46 /* Wake Up Packet Length */
47 #define IGC_WUPL_MASK		0x00000FFF
48 
49 /* Wake Up Packet Memory stores the first 128 bytes of the wake up packet */
50 #define IGC_WUPM_BYTES	128
51 
52 #define IGC_WUS_ARPD	0x00000020 /* Directed ARP Request */
53 #define IGC_WUS_IPV4	0x00000040 /* Directed IPv4 */
54 #define IGC_WUS_IPV6	0x00000080 /* Directed IPv6 */
55 #define IGC_WUS_NSD	0x00000400 /* Directed IPv6 Neighbor Solicitation */
56 
57 /* Extended Device Control */
58 #define IGC_CTRL_EXT_LPCD		0x00000004 /* LCD Power Cycle Done */
59 #define IGC_CTRL_EXT_SDP4_DATA	0x00000010 /* SW Definable Pin 4 data */
60 #define IGC_CTRL_EXT_SDP6_DATA	0x00000040 /* SW Definable Pin 6 data */
61 #define IGC_CTRL_EXT_SDP3_DATA	0x00000080 /* SW Definable Pin 3 data */
62 #define IGC_CTRL_EXT_SDP6_DIR	0x00000400 /* Direction of SDP6 0=in 1=out */
63 #define IGC_CTRL_EXT_SDP3_DIR	0x00000800 /* Direction of SDP3 0=in 1=out */
64 #define IGC_CTRL_EXT_FORCE_SMBUS	0x00000800 /* Force SMBus mode */
65 #define IGC_CTRL_EXT_EE_RST	0x00002000 /* Reinitialize from EEPROM */
66 #define IGC_CTRL_EXT_SPD_BYPS	0x00008000 /* Speed Select Bypass */
67 #define IGC_CTRL_EXT_RO_DIS	0x00020000 /* Relaxed Ordering disable */
68 #define IGC_CTRL_EXT_DMA_DYN_CLK_EN	0x00080000 /* DMA Dynamic Clk Gating */
69 #define IGC_CTRL_EXT_LINK_MODE_PCIE_SERDES	0x00C00000
70 #define IGC_CTRL_EXT_EIAME		0x01000000
71 #define IGC_CTRL_EXT_DRV_LOAD		0x10000000 /* Drv loaded bit for FW */
72 #define IGC_CTRL_EXT_IAME		0x08000000 /* Int ACK Auto-mask */
73 #define IGC_CTRL_EXT_PBA_CLR		0x80000000 /* PBA Clear */
74 #define IGC_CTRL_EXT_PHYPDEN		0x00100000
75 #define IGC_IVAR_VALID	0x80
76 #define IGC_GPIE_NSICR	0x00000001
77 #define IGC_GPIE_MSIX_MODE	0x00000010
78 #define IGC_GPIE_EIAME	0x40000000
79 #define IGC_GPIE_PBA		0x80000000
80 
81 /* Receive Descriptor bit definitions */
82 #define IGC_RXD_STAT_DD	0x01    /* Descriptor Done */
83 #define IGC_RXD_STAT_EOP	0x02    /* End of Packet */
84 #define IGC_RXD_STAT_IXSM	0x04    /* Ignore checksum */
85 #define IGC_RXD_STAT_VP	0x08    /* IEEE VLAN Packet */
86 #define IGC_RXD_STAT_UDPCS	0x10    /* UDP xsum calculated */
87 #define IGC_RXD_STAT_TCPCS	0x20    /* TCP xsum calculated */
88 #define IGC_RXD_STAT_IPCS	0x40    /* IP xsum calculated */
89 #define IGC_RXD_STAT_PIF	0x80    /* passed in-exact filter */
90 #define IGC_RXD_STAT_IPIDV	0x200   /* IP identification valid */
91 #define IGC_RXD_STAT_UDPV	0x400   /* Valid UDP checksum */
92 #define IGC_RXD_ERR_CE	0x01    /* CRC Error */
93 #define IGC_RXD_ERR_SE	0x02    /* Symbol Error */
94 #define IGC_RXD_ERR_SEQ	0x04    /* Sequence Error */
95 #define IGC_RXD_ERR_CXE	0x10    /* Carrier Extension Error */
96 #define IGC_RXD_ERR_TCPE	0x20    /* TCP/UDP Checksum Error */
97 #define IGC_RXD_ERR_IPE	0x40    /* IP Checksum Error */
98 #define IGC_RXD_ERR_RXE	0x80    /* Rx Data Error */
99 #define IGC_RXD_SPC_VLAN_MASK	0x0FFF  /* VLAN ID is in lower 12 bits */
100 
101 #define IGC_RXDEXT_STATERR_TST	0x00000100 /* Time Stamp taken */
102 #define IGC_RXDEXT_STATERR_LB		0x00040000
103 #define IGC_RXDEXT_STATERR_L4E	0x20000000
104 #define IGC_RXDEXT_STATERR_IPE	0x40000000
105 #define IGC_RXDEXT_STATERR_RXE	0x80000000
106 
107 /* Same mask, but for extended and packet split descriptors */
108 #define IGC_RXDEXT_ERR_FRAME_ERR_MASK ( \
109 	IGC_RXDEXT_STATERR_CE  |	\
110 	IGC_RXDEXT_STATERR_SE  |	\
111 	IGC_RXDEXT_STATERR_SEQ |	\
112 	IGC_RXDEXT_STATERR_CXE |	\
113 	IGC_RXDEXT_STATERR_RXE)
114 
115 #if !defined(EXTERNAL_RELEASE) || defined(IGCE_MQ)
116 #define IGC_MRQC_ENABLE_RSS_2Q		0x00000001
117 #endif /* !EXTERNAL_RELEASE || IGCE_MQ */
118 #define IGC_MRQC_RSS_FIELD_MASK		0xFFFF0000
119 #define IGC_MRQC_RSS_FIELD_IPV4_TCP		0x00010000
120 #define IGC_MRQC_RSS_FIELD_IPV4		0x00020000
121 #define IGC_MRQC_RSS_FIELD_IPV6_TCP_EX	0x00040000
122 #define IGC_MRQC_RSS_FIELD_IPV6		0x00100000
123 #define IGC_MRQC_RSS_FIELD_IPV6_TCP		0x00200000
124 
125 #define IGC_RXDPS_HDRSTAT_HDRSP		0x00008000
126 
127 /* Management Control */
128 #define IGC_MANC_SMBUS_EN	0x00000001 /* SMBus Enabled - RO */
129 #define IGC_MANC_ASF_EN	0x00000002 /* ASF Enabled - RO */
130 #define IGC_MANC_ARP_EN	0x00002000 /* Enable ARP Request Filtering */
131 #define IGC_MANC_RCV_TCO_EN	0x00020000 /* Receive TCO Packets Enabled */
132 #define IGC_MANC_BLK_PHY_RST_ON_IDE	0x00040000 /* Block phy resets */
133 /* Enable MAC address filtering */
134 #define IGC_MANC_EN_MAC_ADDR_FILTER	0x00100000
135 /* Enable MNG packets to host memory */
136 #define IGC_MANC_EN_MNG2HOST		0x00200000
137 
138 #define IGC_MANC2H_PORT_623		0x00000020 /* Port 0x26f */
139 #define IGC_MANC2H_PORT_664		0x00000040 /* Port 0x298 */
140 #define IGC_MDEF_PORT_623		0x00000800 /* Port 0x26f */
141 #define IGC_MDEF_PORT_664		0x00000400 /* Port 0x298 */
142 
143 /* Receive Control */
144 #define IGC_RCTL_RST		0x00000001 /* Software reset */
145 #define IGC_RCTL_EN		0x00000002 /* enable */
146 #define IGC_RCTL_SBP		0x00000004 /* store bad packet */
147 #define IGC_RCTL_UPE		0x00000008 /* unicast promisc enable */
148 #define IGC_RCTL_MPE		0x00000010 /* multicast promisc enable */
149 #define IGC_RCTL_LPE		0x00000020 /* long packet enable */
150 #define IGC_RCTL_LBM_NO	0x00000000 /* no loopback mode */
151 #define IGC_RCTL_LBM_MAC	0x00000040 /* MAC loopback mode */
152 #define IGC_RCTL_LBM_TCVR	0x000000C0 /* tcvr loopback mode */
153 #define IGC_RCTL_DTYP_PS	0x00000400 /* Packet Split descriptor */
154 #define IGC_RCTL_RDMTS_HALF	0x00000000 /* Rx desc min thresh size */
155 #define IGC_RCTL_RDMTS_HEX	0x00010000
156 #define IGC_RCTL_RDMTS1_HEX	IGC_RCTL_RDMTS_HEX
157 #define IGC_RCTL_MO_SHIFT	12 /* multicast offset shift */
158 #define IGC_RCTL_MO_3		0x00003000 /* multicast offset 15:4 */
159 #define IGC_RCTL_BAM		0x00008000 /* broadcast enable */
160 /* these buffer sizes are valid if IGC_RCTL_BSEX is 0 */
161 #define IGC_RCTL_SZ_2048	0x00000000 /* Rx buffer size 2048 */
162 #define IGC_RCTL_SZ_1024	0x00010000 /* Rx buffer size 1024 */
163 #define IGC_RCTL_SZ_512	0x00020000 /* Rx buffer size 512 */
164 #define IGC_RCTL_SZ_256	0x00030000 /* Rx buffer size 256 */
165 /* these buffer sizes are valid if IGC_RCTL_BSEX is 1 */
166 #define IGC_RCTL_SZ_16384	0x00010000 /* Rx buffer size 16384 */
167 #define IGC_RCTL_SZ_8192	0x00020000 /* Rx buffer size 8192 */
168 #define IGC_RCTL_SZ_4096	0x00030000 /* Rx buffer size 4096 */
169 #define IGC_RCTL_VFE		0x00040000 /* vlan filter enable */
170 #define IGC_RCTL_CFIEN	0x00080000 /* canonical form enable */
171 #define IGC_RCTL_CFI		0x00100000 /* canonical form indicator */
172 #define IGC_RCTL_DPF		0x00400000 /* discard pause frames */
173 #define IGC_RCTL_PMCF		0x00800000 /* pass MAC control frames */
174 #define IGC_RCTL_BSEX		0x02000000 /* Buffer size extension */
175 #define IGC_RCTL_SECRC	0x04000000 /* Strip Ethernet CRC */
176 
177 /* Use byte values for the following shift parameters
178  * Usage:
179  *     psrctl |= (((ROUNDUP(value0, 128) >> IGC_PSRCTL_BSIZE0_SHIFT) &
180  *		  IGC_PSRCTL_BSIZE0_MASK) |
181  *		((ROUNDUP(value1, 1024) >> IGC_PSRCTL_BSIZE1_SHIFT) &
182  *		  IGC_PSRCTL_BSIZE1_MASK) |
183  *		((ROUNDUP(value2, 1024) << IGC_PSRCTL_BSIZE2_SHIFT) &
184  *		  IGC_PSRCTL_BSIZE2_MASK) |
185  *		((ROUNDUP(value3, 1024) << IGC_PSRCTL_BSIZE3_SHIFT) |;
186  *		  IGC_PSRCTL_BSIZE3_MASK))
187  * where value0 = [128..16256],  default=256
188  *       value1 = [1024..64512], default=4096
189  *       value2 = [0..64512],    default=4096
190  *       value3 = [0..64512],    default=0
191  */
192 
193 #define IGC_PSRCTL_BSIZE0_MASK	0x0000007F
194 #define IGC_PSRCTL_BSIZE1_MASK	0x00003F00
195 #define IGC_PSRCTL_BSIZE2_MASK	0x003F0000
196 #define IGC_PSRCTL_BSIZE3_MASK	0x3F000000
197 
198 #define IGC_PSRCTL_BSIZE0_SHIFT	7    /* Shift _right_ 7 */
199 #define IGC_PSRCTL_BSIZE1_SHIFT	2    /* Shift _right_ 2 */
200 #define IGC_PSRCTL_BSIZE2_SHIFT	6    /* Shift _left_ 6 */
201 #define IGC_PSRCTL_BSIZE3_SHIFT	14   /* Shift _left_ 14 */
202 
203 /* SWFW_SYNC Definitions */
204 #define IGC_SWFW_EEP_SM	0x01
205 #define IGC_SWFW_PHY0_SM	0x02
206 #define IGC_SWFW_PHY1_SM	0x04
207 #define IGC_SWFW_CSR_SM	0x08
208 #define IGC_SWFW_SW_MNG_SM	0x400
209 
210 /* Device Control */
211 #define IGC_CTRL_FD		0x00000001  /* Full duplex.0=half; 1=full */
212 #define IGC_CTRL_PRIOR	0x00000004  /* Priority on PCI. 0=rx,1=fair */
213 #define IGC_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master reqs */
214 #define IGC_CTRL_LRST		0x00000008  /* Link reset. 0=normal,1=reset */
215 #define IGC_CTRL_ASDE		0x00000020  /* Auto-speed detect enable */
216 #define IGC_CTRL_SLU		0x00000040  /* Set link up (Force Link) */
217 #define IGC_CTRL_ILOS		0x00000080  /* Invert Loss-Of Signal */
218 #define IGC_CTRL_SPD_SEL	0x00000300  /* Speed Select Mask */
219 #define IGC_CTRL_SPD_10	0x00000000  /* Force 10Mb */
220 #define IGC_CTRL_SPD_100	0x00000100  /* Force 100Mb */
221 #define IGC_CTRL_SPD_1000	0x00000200  /* Force 1Gb */
222 #define IGC_CTRL_FRCSPD	0x00000800  /* Force Speed */
223 #define IGC_CTRL_FRCDPX	0x00001000  /* Force Duplex */
224 #define IGC_CTRL_SWDPIN0	0x00040000 /* SWDPIN 0 value */
225 #define IGC_CTRL_SWDPIN1	0x00080000 /* SWDPIN 1 value */
226 #define IGC_CTRL_SWDPIN2	0x00100000 /* SWDPIN 2 value */
227 #define IGC_CTRL_ADVD3WUC	0x00100000 /* D3 WUC */
228 #define IGC_CTRL_SWDPIN3	0x00200000 /* SWDPIN 3 value */
229 #define IGC_CTRL_SWDPIO0	0x00400000 /* SWDPIN 0 Input or output */
230 #define IGC_CTRL_DEV_RST	0x20000000 /* Device reset */
231 #define IGC_CTRL_RST		0x04000000 /* Global reset */
232 #define IGC_CTRL_RFCE		0x08000000 /* Receive Flow Control enable */
233 #define IGC_CTRL_TFCE		0x10000000 /* Transmit flow control enable */
234 #define IGC_CTRL_VME		0x40000000 /* IEEE VLAN mode enable */
235 #define IGC_CTRL_PHY_RST	0x80000000 /* PHY Reset */
236 
237 
238 #define IGC_CONNSW_AUTOSENSE_EN	0x1
239 #define IGC_PCS_LCTL_FORCE_FCTRL	0x80
240 
241 #define IGC_PCS_LSTS_AN_COMPLETE	0x10000
242 
243 /* Device Status */
244 #define IGC_STATUS_FD			0x00000001 /* Duplex 0=half 1=full */
245 #define IGC_STATUS_LU			0x00000002 /* Link up.0=no,1=link */
246 #define IGC_STATUS_FUNC_MASK		0x0000000C /* PCI Function Mask */
247 #define IGC_STATUS_FUNC_SHIFT		2
248 #define IGC_STATUS_FUNC_1		0x00000004 /* Function 1 */
249 #define IGC_STATUS_TXOFF		0x00000010 /* transmission paused */
250 #define IGC_STATUS_SPEED_MASK	0x000000C0
251 #define IGC_STATUS_SPEED_10		0x00000000 /* Speed 10Mb/s */
252 #define IGC_STATUS_SPEED_100		0x00000040 /* Speed 100Mb/s */
253 #define IGC_STATUS_SPEED_1000		0x00000080 /* Speed 1000Mb/s */
254 #define IGC_STATUS_SPEED_2500		0x00400000 /* Speed 2.5Gb/s indication for I225 */
255 #define IGC_STATUS_LAN_INIT_DONE	0x00000200 /* Lan Init Compltn by NVM */
256 #define IGC_STATUS_PHYRA		0x00000400 /* PHY Reset Asserted */
257 #define IGC_STATUS_GIO_MASTER_ENABLE	0x00080000 /* Master request status */
258 #define IGC_STATUS_2P5_SKU		0x00001000 /* Val of 2.5GBE SKU strap */
259 #define IGC_STATUS_2P5_SKU_OVER	0x00002000 /* Val of 2.5GBE SKU Over */
260 #define IGC_STATUS_PCIM_STATE		0x40000000 /* PCIm function state */
261 
262 #define SPEED_10	10
263 #define SPEED_100	100
264 #define SPEED_1000	1000
265 #define SPEED_2500	2500
266 #define HALF_DUPLEX	1
267 #define FULL_DUPLEX	2
268 
269 
270 #define ADVERTISE_10_HALF		0x0001
271 #define ADVERTISE_10_FULL		0x0002
272 #define ADVERTISE_100_HALF		0x0004
273 #define ADVERTISE_100_FULL		0x0008
274 #define ADVERTISE_1000_HALF		0x0010 /* Not used, just FYI */
275 #define ADVERTISE_1000_FULL		0x0020
276 #define ADVERTISE_2500_HALF		0x0040 /* NOT used, just FYI */
277 #define ADVERTISE_2500_FULL		0x0080
278 
279 /* 1000/H is not supported, nor spec-compliant. */
280 #define IGC_ALL_SPEED_DUPLEX	( \
281 	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
282 	ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
283 #define IGC_ALL_SPEED_DUPLEX_2500 ( \
284 	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
285 	ADVERTISE_100_FULL | ADVERTISE_1000_FULL | ADVERTISE_2500_FULL)
286 #define IGC_ALL_NOT_GIG	( \
287 	ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
288 	ADVERTISE_100_FULL)
289 #define IGC_ALL_100_SPEED	(ADVERTISE_100_HALF | ADVERTISE_100_FULL)
290 #define IGC_ALL_10_SPEED	(ADVERTISE_10_HALF | ADVERTISE_10_FULL)
291 #define IGC_ALL_HALF_DUPLEX	(ADVERTISE_10_HALF | ADVERTISE_100_HALF)
292 
293 #define AUTONEG_ADVERTISE_SPEED_DEFAULT		IGC_ALL_SPEED_DUPLEX
294 #define AUTONEG_ADVERTISE_SPEED_DEFAULT_2500	IGC_ALL_SPEED_DUPLEX_2500
295 
296 /* LED Control */
297 #define IGC_LEDCTL_LED0_MODE_MASK	0x0000000F
298 #define IGC_LEDCTL_LED0_MODE_SHIFT	0
299 #define IGC_LEDCTL_LED0_IVRT		0x00000040
300 #define IGC_LEDCTL_LED0_BLINK		0x00000080
301 
302 #define IGC_LEDCTL_MODE_LED_ON	0xE
303 #define IGC_LEDCTL_MODE_LED_OFF	0xF
304 
305 /* Transmit Descriptor bit definitions */
306 #define IGC_TXD_DTYP_D	0x00100000 /* Data Descriptor */
307 #define IGC_TXD_DTYP_C	0x00000000 /* Context Descriptor */
308 #define IGC_TXD_POPTS_IXSM	0x01       /* Insert IP checksum */
309 #define IGC_TXD_POPTS_TXSM	0x02       /* Insert TCP/UDP checksum */
310 #define IGC_TXD_CMD_EOP	0x01000000 /* End of Packet */
311 #define IGC_TXD_CMD_IFCS	0x02000000 /* Insert FCS (Ethernet CRC) */
312 #define IGC_TXD_CMD_IC	0x04000000 /* Insert Checksum */
313 #define IGC_TXD_CMD_RS	0x08000000 /* Report Status */
314 #define IGC_TXD_CMD_RPS	0x10000000 /* Report Packet Sent */
315 #define IGC_TXD_CMD_DEXT	0x20000000 /* Desc extension (0 = legacy) */
316 #define IGC_TXD_CMD_VLE	0x40000000 /* Add VLAN tag */
317 #define IGC_TXD_CMD_IDE	0x80000000 /* Enable Tidv register */
318 #define IGC_TXD_STAT_DD	0x00000001 /* Descriptor Done */
319 #define IGC_TXD_CMD_TCP	0x01000000 /* TCP packet */
320 #define IGC_TXD_CMD_IP	0x02000000 /* IP packet */
321 #define IGC_TXD_CMD_TSE	0x04000000 /* TCP Seg enable */
322 #define IGC_TXD_EXTCMD_TSTAMP	0x00000010 /* IEEE1588 Timestamp packet */
323 
324 /* Transmit Control */
325 #define IGC_TCTL_EN		0x00000002 /* enable Tx */
326 #define IGC_TCTL_PSP		0x00000008 /* pad short packets */
327 #define IGC_TCTL_CT		0x00000ff0 /* collision threshold */
328 #define IGC_TCTL_COLD		0x003ff000 /* collision distance */
329 #define IGC_TCTL_RTLC		0x01000000 /* Re-transmit on late collision */
330 #define IGC_TCTL_MULR		0x10000000 /* Multiple request support */
331 
332 /* Transmit Arbitration Count */
333 #define IGC_TARC0_ENABLE	0x00000400 /* Enable Tx Queue 0 */
334 
335 /* SerDes Control */
336 #define IGC_SCTL_DISABLE_SERDES_LOOPBACK	0x0400
337 #define IGC_SCTL_ENABLE_SERDES_LOOPBACK	0x0410
338 
339 /* Receive Checksum Control */
340 #define IGC_RXCSUM_IPOFL	0x00000100 /* IPv4 checksum offload */
341 #define IGC_RXCSUM_TUOFL	0x00000200 /* TCP / UDP checksum offload */
342 #define IGC_RXCSUM_CRCOFL	0x00000800 /* CRC32 offload enable */
343 #define IGC_RXCSUM_IPPCSE	0x00001000 /* IP payload checksum enable */
344 #define IGC_RXCSUM_PCSD		0x00002000 /* packet checksum disabled */
345 
346 /* GPY211 - I225 defines */
347 #define GPY_MMD_MASK		0xFFFF0000
348 #define GPY_MMD_SHIFT		16
349 #define GPY_REG_MASK		0x0000FFFF
350 /* Header split receive */
351 #define IGC_RFCTL_NFSW_DIS		0x00000040
352 #define IGC_RFCTL_NFSR_DIS		0x00000080
353 #define IGC_RFCTL_ACK_DIS		0x00001000
354 #define IGC_RFCTL_EXTEN			0x00008000
355 #define IGC_RFCTL_IPV6_EX_DIS		0x00010000
356 #define IGC_RFCTL_NEW_IPV6_EXT_DIS	0x00020000
357 #define IGC_RFCTL_LEF			0x00040000
358 
359 /* Collision related configuration parameters */
360 #define IGC_CT_SHIFT			4
361 #define IGC_COLLISION_THRESHOLD		15
362 #define IGC_COLLISION_DISTANCE		63
363 #define IGC_COLD_SHIFT			12
364 
365 /* Default values for the transmit IPG register */
366 #define DEFAULT_82543_TIPG_IPGT_FIBER	9
367 #define DEFAULT_82543_TIPG_IPGT_COPPER	8
368 
369 #define IGC_TIPG_IPGT_MASK		0x000003FF
370 
371 #define DEFAULT_82543_TIPG_IPGR1	8
372 #define IGC_TIPG_IPGR1_SHIFT		10
373 
374 #define DEFAULT_82543_TIPG_IPGR2	6
375 #define DEFAULT_80003ES2LAN_TIPG_IPGR2	7
376 #define IGC_TIPG_IPGR2_SHIFT		20
377 
378 /* Ethertype field values */
379 #define ETHERNET_IEEE_VLAN_TYPE		0x8100  /* 802.3ac packet */
380 
381 #define ETHERNET_FCS_SIZE		4
382 #define MAX_JUMBO_FRAME_SIZE		MJUM9BYTES
383 #define IGC_TX_PTR_GAP			0x1F
384 
385 /* Extended Configuration Control and Size */
386 #define IGC_EXTCNF_CTRL_MDIO_SW_OWNERSHIP	0x00000020
387 #define IGC_EXTCNF_CTRL_LCD_WRITE_ENABLE	0x00000001
388 #define IGC_EXTCNF_CTRL_OEM_WRITE_ENABLE	0x00000008
389 #define IGC_EXTCNF_CTRL_SWFLAG			0x00000020
390 #define IGC_EXTCNF_CTRL_GATE_PHY_CFG		0x00000080
391 #define IGC_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK	0x00FF0000
392 #define IGC_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT	16
393 #define IGC_EXTCNF_CTRL_EXT_CNF_POINTER_MASK	0x0FFF0000
394 #define IGC_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT	16
395 
396 #define IGC_PHY_CTRL_D0A_LPLU			0x00000002
397 #define IGC_PHY_CTRL_NOND0A_LPLU		0x00000004
398 #define IGC_PHY_CTRL_NOND0A_GBE_DISABLE		0x00000008
399 #define IGC_PHY_CTRL_GBE_DISABLE		0x00000040
400 
401 #define IGC_KABGTXD_BGSQLBIAS			0x00050000
402 
403 /* PBA constants */
404 #define IGC_PBA_8K		0x0008    /* 8KB */
405 #define IGC_PBA_10K		0x000A    /* 10KB */
406 #define IGC_PBA_12K		0x000C    /* 12KB */
407 #define IGC_PBA_14K		0x000E    /* 14KB */
408 #define IGC_PBA_16K		0x0010    /* 16KB */
409 #define IGC_PBA_18K		0x0012
410 #define IGC_PBA_20K		0x0014
411 #define IGC_PBA_22K		0x0016
412 #define IGC_PBA_24K		0x0018
413 #define IGC_PBA_26K		0x001A
414 #define IGC_PBA_30K		0x001E
415 #define IGC_PBA_32K		0x0020
416 #define IGC_PBA_34K		0x0022
417 #define IGC_PBA_35K		0x0023
418 #define IGC_PBA_38K		0x0026
419 #define IGC_PBA_40K		0x0028
420 #define IGC_PBA_48K		0x0030    /* 48KB */
421 #define IGC_PBA_64K		0x0040    /* 64KB */
422 
423 #define IGC_PBA_RXA_MASK	0xFFFF
424 
425 #define IGC_PBS_16K		IGC_PBA_16K
426 
427 /* Uncorrectable/correctable ECC Error counts and enable bits */
428 #define IGC_PBECCSTS_CORR_ERR_CNT_MASK		0x000000FF
429 #define IGC_PBECCSTS_UNCORR_ERR_CNT_MASK	0x0000FF00
430 #define IGC_PBECCSTS_UNCORR_ERR_CNT_SHIFT	8
431 #define IGC_PBECCSTS_ECC_ENABLE			0x00010000
432 
433 #define IFS_MAX			80
434 #define IFS_MIN			40
435 #define IFS_RATIO		4
436 #define IFS_STEP		10
437 #define MIN_NUM_XMITS		1000
438 
439 /* SW Semaphore Register */
440 #define IGC_SWSM_SMBI		0x00000001 /* Driver Semaphore bit */
441 #define IGC_SWSM_SWESMBI	0x00000002 /* FW Semaphore bit */
442 #define IGC_SWSM_DRV_LOAD	0x00000008 /* Driver Loaded Bit */
443 
444 #define IGC_SWSM2_LOCK		0x00000002 /* Secondary driver semaphore bit */
445 
446 /* Interrupt Cause Read */
447 #define IGC_ICR_TXDW		0x00000001 /* Transmit desc written back */
448 #define IGC_ICR_TXQE		0x00000002 /* Transmit Queue empty */
449 #define IGC_ICR_LSC		0x00000004 /* Link Status Change */
450 #define IGC_ICR_RXSEQ		0x00000008 /* Rx sequence error */
451 #define IGC_ICR_RXDMT0		0x00000010 /* Rx desc min. threshold (0) */
452 #define IGC_ICR_RXO		0x00000040 /* Rx overrun */
453 #define IGC_ICR_RXT0		0x00000080 /* Rx timer intr (ring 0) */
454 #define IGC_ICR_RXCFG		0x00000400 /* Rx /c/ ordered set */
455 #define IGC_ICR_GPI_EN0		0x00000800 /* GP Int 0 */
456 #define IGC_ICR_GPI_EN1		0x00001000 /* GP Int 1 */
457 #define IGC_ICR_GPI_EN2		0x00002000 /* GP Int 2 */
458 #define IGC_ICR_GPI_EN3		0x00004000 /* GP Int 3 */
459 #define IGC_ICR_TXD_LOW		0x00008000
460 #define IGC_ICR_ECCER		0x00400000 /* Uncorrectable ECC Error */
461 #define IGC_ICR_TS		0x00080000 /* Time Sync Interrupt */
462 #define IGC_ICR_DRSTA		0x40000000 /* Device Reset Asserted */
463 /* If this bit asserted, the driver should claim the interrupt */
464 #define IGC_ICR_INT_ASSERTED	0x80000000
465 #define IGC_ICR_DOUTSYNC	0x10000000 /* NIC DMA out of sync */
466 #define IGC_ICR_FER		0x00400000 /* Fatal Error */
467 
468 
469 
470 /* Extended Interrupt Cause Read */
471 #define IGC_EICR_RX_QUEUE0	0x00000001 /* Rx Queue 0 Interrupt */
472 #define IGC_EICR_RX_QUEUE1	0x00000002 /* Rx Queue 1 Interrupt */
473 #define IGC_EICR_RX_QUEUE2	0x00000004 /* Rx Queue 2 Interrupt */
474 #define IGC_EICR_RX_QUEUE3	0x00000008 /* Rx Queue 3 Interrupt */
475 #define IGC_EICR_TX_QUEUE0	0x00000100 /* Tx Queue 0 Interrupt */
476 #define IGC_EICR_TX_QUEUE1	0x00000200 /* Tx Queue 1 Interrupt */
477 #define IGC_EICR_TX_QUEUE2	0x00000400 /* Tx Queue 2 Interrupt */
478 #define IGC_EICR_TX_QUEUE3	0x00000800 /* Tx Queue 3 Interrupt */
479 #define IGC_EICR_TCP_TIMER	0x40000000 /* TCP Timer */
480 #define IGC_EICR_OTHER		0x80000000 /* Interrupt Cause Active */
481 /* TCP Timer */
482 #define IGC_TCPTIMER_KS			0x00000100 /* KickStart */
483 #define IGC_TCPTIMER_COUNT_ENABLE	0x00000200 /* Count Enable */
484 #define IGC_TCPTIMER_COUNT_FINISH	0x00000400 /* Count finish */
485 #define IGC_TCPTIMER_LOOP		0x00000800 /* Loop */
486 
487 /* This defines the bits that are set in the Interrupt Mask
488  * Set/Read Register.  Each bit is documented below:
489  *   o RXT0   = Receiver Timer Interrupt (ring 0)
490  *   o TXDW   = Transmit Descriptor Written Back
491  *   o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
492  *   o RXSEQ  = Receive Sequence Error
493  *   o LSC    = Link Status Change
494  */
495 #define IMS_ENABLE_MASK ( \
496 	IGC_IMS_RXT0   |    \
497 	IGC_IMS_TXDW   |    \
498 	IGC_IMS_RXDMT0 |    \
499 	IGC_IMS_RXSEQ  |    \
500 	IGC_IMS_LSC)
501 
502 /* Interrupt Mask Set */
503 #define IGC_IMS_TXDW		IGC_ICR_TXDW    /* Tx desc written back */
504 #define IGC_IMS_LSC		IGC_ICR_LSC     /* Link Status Change */
505 #define IGC_IMS_RXSEQ		IGC_ICR_RXSEQ   /* Rx sequence error */
506 #define IGC_IMS_RXDMT0		IGC_ICR_RXDMT0  /* Rx desc min. threshold */
507 #define IGC_QVECTOR_MASK	0x7FFC		/* Q-vector mask */
508 #define IGC_ITR_VAL_MASK	0x04		/* ITR value mask */
509 #define IGC_IMS_RXO		IGC_ICR_RXO     /* Rx overrun */
510 #define IGC_IMS_RXT0		IGC_ICR_RXT0    /* Rx timer intr */
511 #define IGC_IMS_TXD_LOW		IGC_ICR_TXD_LOW
512 #define IGC_IMS_ECCER		IGC_ICR_ECCER   /* Uncorrectable ECC Error */
513 #define IGC_IMS_TS		IGC_ICR_TS      /* Time Sync Interrupt */
514 #define IGC_IMS_DRSTA		IGC_ICR_DRSTA   /* Device Reset Asserted */
515 #define IGC_IMS_DOUTSYNC	IGC_ICR_DOUTSYNC /* NIC DMA out of sync */
516 #define IGC_IMS_FER		IGC_ICR_FER /* Fatal Error */
517 
518 #define IGC_IMS_THS		IGC_ICR_THS /* ICR.TS: Thermal Sensor Event*/
519 #define IGC_IMS_MDDET		IGC_ICR_MDDET /* Malicious Driver Detect */
520 /* Extended Interrupt Mask Set */
521 #define IGC_EIMS_RX_QUEUE0	IGC_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */
522 #define IGC_EIMS_RX_QUEUE1	IGC_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */
523 #define IGC_EIMS_RX_QUEUE2	IGC_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */
524 #define IGC_EIMS_RX_QUEUE3	IGC_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */
525 #define IGC_EIMS_TX_QUEUE0	IGC_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */
526 #define IGC_EIMS_TX_QUEUE1	IGC_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */
527 #define IGC_EIMS_TX_QUEUE2	IGC_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */
528 #define IGC_EIMS_TX_QUEUE3	IGC_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */
529 #define IGC_EIMS_TCP_TIMER	IGC_EICR_TCP_TIMER /* TCP Timer */
530 #define IGC_EIMS_OTHER		IGC_EICR_OTHER   /* Interrupt Cause Active */
531 
532 /* Interrupt Cause Set */
533 #define IGC_ICS_LSC		IGC_ICR_LSC       /* Link Status Change */
534 #define IGC_ICS_RXSEQ		IGC_ICR_RXSEQ     /* Rx sequence error */
535 #define IGC_ICS_RXDMT0		IGC_ICR_RXDMT0    /* Rx desc min. threshold */
536 
537 /* Extended Interrupt Cause Set */
538 #define IGC_EICS_RX_QUEUE0	IGC_EICR_RX_QUEUE0 /* Rx Queue 0 Interrupt */
539 #define IGC_EICS_RX_QUEUE1	IGC_EICR_RX_QUEUE1 /* Rx Queue 1 Interrupt */
540 #define IGC_EICS_RX_QUEUE2	IGC_EICR_RX_QUEUE2 /* Rx Queue 2 Interrupt */
541 #define IGC_EICS_RX_QUEUE3	IGC_EICR_RX_QUEUE3 /* Rx Queue 3 Interrupt */
542 #define IGC_EICS_TX_QUEUE0	IGC_EICR_TX_QUEUE0 /* Tx Queue 0 Interrupt */
543 #define IGC_EICS_TX_QUEUE1	IGC_EICR_TX_QUEUE1 /* Tx Queue 1 Interrupt */
544 #define IGC_EICS_TX_QUEUE2	IGC_EICR_TX_QUEUE2 /* Tx Queue 2 Interrupt */
545 #define IGC_EICS_TX_QUEUE3	IGC_EICR_TX_QUEUE3 /* Tx Queue 3 Interrupt */
546 #define IGC_EICS_TCP_TIMER	IGC_EICR_TCP_TIMER /* TCP Timer */
547 #define IGC_EICS_OTHER		IGC_EICR_OTHER   /* Interrupt Cause Active */
548 
549 #define IGC_EITR_ITR_INT_MASK	0x0000FFFF
550 #define IGC_EITR_INTERVAL 	0x00007FFC
551 /* IGC_EITR_CNT_IGNR is only for 82576 and newer */
552 #define IGC_EITR_CNT_IGNR	0x80000000 /* Don't reset counters on write */
553 
554 /* Transmit Descriptor Control */
555 #define IGC_TXDCTL_PTHRESH	0x0000003F /* TXDCTL Prefetch Threshold */
556 #define IGC_TXDCTL_HTHRESH	0x00003F00 /* TXDCTL Host Threshold */
557 #define IGC_TXDCTL_WTHRESH	0x003F0000 /* TXDCTL Writeback Threshold */
558 #define IGC_TXDCTL_GRAN		0x01000000 /* TXDCTL Granularity */
559 #define IGC_TXDCTL_FULL_TX_DESC_WB	0x01010000 /* GRAN=1, WTHRESH=1 */
560 #define IGC_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
561 /* Enable the counting of descriptors still to be processed. */
562 #define IGC_TXDCTL_COUNT_DESC	0x00400000
563 
564 /* Flow Control Constants */
565 #define FLOW_CONTROL_ADDRESS_LOW	0x00C28001
566 #define FLOW_CONTROL_ADDRESS_HIGH	0x00000100
567 #define FLOW_CONTROL_TYPE		0x8808
568 
569 /* 802.1q VLAN Packet Size */
570 #define VLAN_TAG_SIZE			4    /* 802.3ac tag (not DMA'd) */
571 #define IGC_VLAN_FILTER_TBL_SIZE	128  /* VLAN Filter Table (4096 bits) */
572 
573 /* Receive Address
574  * Number of high/low register pairs in the RAR. The RAR (Receive Address
575  * Registers) holds the directed and multicast addresses that we monitor.
576  * Technically, we have 16 spots.  However, we reserve one of these spots
577  * (RAR[15]) for our directed address used by controllers with
578  * manageability enabled, allowing us room for 15 multicast addresses.
579  */
580 #define IGC_RAR_ENTRIES		15
581 #define IGC_RAH_AV		0x80000000 /* Receive descriptor valid */
582 #define IGC_RAL_MAC_ADDR_LEN	4
583 #define IGC_RAH_MAC_ADDR_LEN	2
584 
585 /* Error Codes */
586 #define IGC_SUCCESS			0
587 #define IGC_ERR_NVM			1
588 #define IGC_ERR_PHY			2
589 #define IGC_ERR_CONFIG			3
590 #define IGC_ERR_PARAM			4
591 #define IGC_ERR_MAC_INIT		5
592 #define IGC_ERR_PHY_TYPE		6
593 #define IGC_ERR_RESET			9
594 #define IGC_ERR_MASTER_REQUESTS_PENDING	10
595 #define IGC_ERR_HOST_INTERFACE_COMMAND	11
596 #define IGC_BLK_PHY_RESET		12
597 #define IGC_ERR_SWFW_SYNC		13
598 #define IGC_NOT_IMPLEMENTED		14
599 #define IGC_ERR_MBX			15
600 #define IGC_ERR_INVALID_ARGUMENT	16
601 #define IGC_ERR_NO_SPACE		17
602 #define IGC_ERR_NVM_PBA_SECTION		18
603 #define IGC_ERR_INVM_VALUE_NOT_FOUND	20
604 
605 /* Loop limit on how long we wait for auto-negotiation to complete */
606 #define COPPER_LINK_UP_LIMIT		10
607 #define PHY_AUTO_NEG_LIMIT		45
608 /* Number of 100 microseconds we wait for PCI Express master disable */
609 #define MASTER_DISABLE_TIMEOUT		800
610 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
611 #define PHY_CFG_TIMEOUT			100
612 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
613 #define MDIO_OWNERSHIP_TIMEOUT		10
614 /* Number of milliseconds for NVM auto read done after MAC reset. */
615 #define AUTO_READ_DONE_TIMEOUT		10
616 
617 /* Flow Control */
618 #define IGC_FCRTH_RTH		0x0000FFF8 /* Mask Bits[15:3] for RTH */
619 #define IGC_FCRTL_RTL		0x0000FFF8 /* Mask Bits[15:3] for RTL */
620 #define IGC_FCRTL_XONE		0x80000000 /* Enable XON frame transmission */
621 
622 /* Transmit Configuration Word */
623 #define IGC_TXCW_FD		0x00000020 /* TXCW full duplex */
624 #define IGC_TXCW_PAUSE		0x00000080 /* TXCW sym pause request */
625 #define IGC_TXCW_ASM_DIR	0x00000100 /* TXCW astm pause direction */
626 #define IGC_TXCW_PAUSE_MASK	0x00000180 /* TXCW pause request mask */
627 #define IGC_TXCW_ANE		0x80000000 /* Auto-neg enable */
628 
629 /* Receive Configuration Word */
630 #define IGC_RXCW_CW		0x0000ffff /* RxConfigWord mask */
631 #define IGC_RXCW_IV		0x08000000 /* Receive config invalid */
632 #define IGC_RXCW_C		0x20000000 /* Receive config */
633 #define IGC_RXCW_SYNCH		0x40000000 /* Receive config synch */
634 
635 #define IGC_TSYNCTXCTL_TXTT_0	0x00000001 /* Tx timestamp reg 0 valid */
636 #define IGC_TSYNCTXCTL_ENABLED	0x00000010 /* enable Tx timestamping */
637 
638 #define IGC_TSYNCRXCTL_VALID		0x00000001 /* Rx timestamp valid */
639 #define IGC_TSYNCRXCTL_TYPE_MASK	0x0000000E /* Rx type mask */
640 #define IGC_TSYNCRXCTL_TYPE_L2_V2	0x00
641 #define IGC_TSYNCRXCTL_TYPE_L4_V1	0x02
642 #define IGC_TSYNCRXCTL_TYPE_L2_L4_V2	0x04
643 #define IGC_TSYNCRXCTL_TYPE_ALL		0x08
644 #define IGC_TSYNCRXCTL_TYPE_EVENT_V2	0x0A
645 #define IGC_TSYNCRXCTL_ENABLED		0x00000010 /* enable Rx timestamping */
646 #define IGC_TSYNCRXCTL_SYSCFI		0x00000020 /* Sys clock frequency */
647 
648 #define IGC_TSYNCRXCFG_PTP_V1_CTRLT_MASK		0x000000FF
649 #define IGC_TSYNCRXCFG_PTP_V1_SYNC_MESSAGE		0x00
650 #define IGC_TSYNCRXCFG_PTP_V1_DELAY_REQ_MESSAGE		0x01
651 #define IGC_TSYNCRXCFG_PTP_V1_FOLLOWUP_MESSAGE		0x02
652 #define IGC_TSYNCRXCFG_PTP_V1_DELAY_RESP_MESSAGE	0x03
653 #define IGC_TSYNCRXCFG_PTP_V1_MANAGEMENT_MESSAGE	0x04
654 
655 #define IGC_TSYNCRXCFG_PTP_V2_MSGID_MASK		0x00000F00
656 #define IGC_TSYNCRXCFG_PTP_V2_SYNC_MESSAGE		0x0000
657 #define IGC_TSYNCRXCFG_PTP_V2_DELAY_REQ_MESSAGE		0x0100
658 #define IGC_TSYNCRXCFG_PTP_V2_PATH_DELAY_REQ_MESSAGE	0x0200
659 #define IGC_TSYNCRXCFG_PTP_V2_PATH_DELAY_RESP_MESSAGE	0x0300
660 #define IGC_TSYNCRXCFG_PTP_V2_FOLLOWUP_MESSAGE		0x0800
661 #define IGC_TSYNCRXCFG_PTP_V2_DELAY_RESP_MESSAGE	0x0900
662 #define IGC_TSYNCRXCFG_PTP_V2_PATH_DELAY_FOLLOWUP_MESSAGE 0x0A00
663 #define IGC_TSYNCRXCFG_PTP_V2_ANNOUNCE_MESSAGE		0x0B00
664 #define IGC_TSYNCRXCFG_PTP_V2_SIGNALLING_MESSAGE	0x0C00
665 #define IGC_TSYNCRXCFG_PTP_V2_MANAGEMENT_MESSAGE	0x0D00
666 
667 #define IGC_TIMINCA_16NS_SHIFT		24
668 #define IGC_TIMINCA_INCPERIOD_SHIFT	24
669 #define IGC_TIMINCA_INCVALUE_MASK	0x00FFFFFF
670 
671 /* Time Sync Interrupt Cause/Mask Register Bits */
672 #define TSINTR_SYS_WRAP	(1 << 0) /* SYSTIM Wrap around. */
673 #define TSINTR_TXTS	(1 << 1) /* Transmit Timestamp. */
674 #define TSINTR_TT0	(1 << 3) /* Target Time 0 Trigger. */
675 #define TSINTR_TT1	(1 << 4) /* Target Time 1 Trigger. */
676 #define TSINTR_AUTT0	(1 << 5) /* Auxiliary Timestamp 0 Taken. */
677 #define TSINTR_AUTT1	(1 << 6) /* Auxiliary Timestamp 1 Taken. */
678 
679 #define TSYNC_INTERRUPTS	TSINTR_TXTS
680 
681 /* TSAUXC Configuration Bits */
682 #define TSAUXC_EN_TT0	(1 << 0)  /* Enable target time 0. */
683 #define TSAUXC_EN_TT1	(1 << 1)  /* Enable target time 1. */
684 #define TSAUXC_EN_CLK0	(1 << 2)  /* Enable Configurable Frequency Clock 0. */
685 #define TSAUXC_ST0	(1 << 4)  /* Start Clock 0 Toggle on Target Time 0. */
686 #define TSAUXC_EN_CLK1	(1 << 5)  /* Enable Configurable Frequency Clock 1. */
687 #define TSAUXC_ST1	(1 << 7)  /* Start Clock 1 Toggle on Target Time 1. */
688 #define TSAUXC_EN_TS0	(1 << 8)  /* Enable hardware timestamp 0. */
689 #define TSAUXC_EN_TS1	(1 << 10) /* Enable hardware timestamp 0. */
690 
691 /* SDP Configuration Bits */
692 #define AUX0_SEL_SDP0	(0u << 0)  /* Assign SDP0 to auxiliary time stamp 0. */
693 #define AUX0_SEL_SDP1	(1u << 0)  /* Assign SDP1 to auxiliary time stamp 0. */
694 #define AUX0_SEL_SDP2	(2u << 0)  /* Assign SDP2 to auxiliary time stamp 0. */
695 #define AUX0_SEL_SDP3	(3u << 0)  /* Assign SDP3 to auxiliary time stamp 0. */
696 #define AUX0_TS_SDP_EN	(1u << 2)  /* Enable auxiliary time stamp trigger 0. */
697 #define AUX1_SEL_SDP0	(0u << 3)  /* Assign SDP0 to auxiliary time stamp 1. */
698 #define AUX1_SEL_SDP1	(1u << 3)  /* Assign SDP1 to auxiliary time stamp 1. */
699 #define AUX1_SEL_SDP2	(2u << 3)  /* Assign SDP2 to auxiliary time stamp 1. */
700 #define AUX1_SEL_SDP3	(3u << 3)  /* Assign SDP3 to auxiliary time stamp 1. */
701 #define AUX1_TS_SDP_EN	(1u << 5)  /* Enable auxiliary time stamp trigger 1. */
702 #define TS_SDP0_EN	(1u << 8)  /* SDP0 is assigned to Tsync. */
703 #define TS_SDP1_EN	(1u << 11) /* SDP1 is assigned to Tsync. */
704 #define TS_SDP2_EN	(1u << 14) /* SDP2 is assigned to Tsync. */
705 #define TS_SDP3_EN	(1u << 17) /* SDP3 is assigned to Tsync. */
706 #define TS_SDP0_SEL_TT0	(0u << 6)  /* Target time 0 is output on SDP0. */
707 #define TS_SDP0_SEL_TT1	(1u << 6)  /* Target time 1 is output on SDP0. */
708 #define TS_SDP1_SEL_TT0	(0u << 9)  /* Target time 0 is output on SDP1. */
709 #define TS_SDP1_SEL_TT1	(1u << 9)  /* Target time 1 is output on SDP1. */
710 #define TS_SDP0_SEL_FC0	(2u << 6)  /* Freq clock  0 is output on SDP0. */
711 #define TS_SDP0_SEL_FC1	(3u << 6)  /* Freq clock  1 is output on SDP0. */
712 #define TS_SDP1_SEL_FC0	(2u << 9)  /* Freq clock  0 is output on SDP1. */
713 #define TS_SDP1_SEL_FC1	(3u << 9)  /* Freq clock  1 is output on SDP1. */
714 #define TS_SDP2_SEL_TT0	(0u << 12) /* Target time 0 is output on SDP2. */
715 #define TS_SDP2_SEL_TT1	(1u << 12) /* Target time 1 is output on SDP2. */
716 #define TS_SDP2_SEL_FC0	(2u << 12) /* Freq clock  0 is output on SDP2. */
717 #define TS_SDP2_SEL_FC1	(3u << 12) /* Freq clock  1 is output on SDP2. */
718 #define TS_SDP3_SEL_TT0	(0u << 15) /* Target time 0 is output on SDP3. */
719 #define TS_SDP3_SEL_TT1	(1u << 15) /* Target time 1 is output on SDP3. */
720 #define TS_SDP3_SEL_FC0	(2u << 15) /* Freq clock  0 is output on SDP3. */
721 #define TS_SDP3_SEL_FC1	(3u << 15) /* Freq clock  1 is output on SDP3. */
722 
723 #define IGC_CTRL_SDP0_DIR	0x00400000  /* SDP0 Data direction */
724 #define IGC_CTRL_SDP1_DIR	0x00800000  /* SDP1 Data direction */
725 
726 /* Extended Device Control */
727 #define IGC_CTRL_EXT_SDP2_DIR	0x00000400 /* SDP2 Data direction */
728 
729 /* ETQF register bit definitions */
730 #define IGC_ETQF_1588			(1 << 30)
731 #define IGC_FTQF_VF_BP			0x00008000
732 #define IGC_FTQF_1588_TIME_STAMP	0x08000000
733 #define IGC_FTQF_MASK			0xF0000000
734 #define IGC_FTQF_MASK_PROTO_BP		0x10000000
735 /* Immediate Interrupt Rx (A.K.A. Low Latency Interrupt) */
736 #define IGC_IMIREXT_CTRL_BP	0x00080000  /* Bypass check of ctrl bits */
737 #define IGC_IMIREXT_SIZE_BP	0x00001000  /* Packet size bypass */
738 
739 #define IGC_RXDADV_STAT_TSIP		0x08000 /* timestamp in packet */
740 #define IGC_TSICR_TXTS			0x00000002
741 #define IGC_TSIM_TXTS			0x00000002
742 /* TUPLE Filtering Configuration */
743 #define IGC_TTQF_DISABLE_MASK		0xF0008000 /* TTQF Disable Mask */
744 #define IGC_TTQF_QUEUE_ENABLE		0x100   /* TTQF Queue Enable Bit */
745 #define IGC_TTQF_PROTOCOL_MASK		0xFF    /* TTQF Protocol Mask */
746 /* TTQF TCP Bit, shift with IGC_TTQF_PROTOCOL SHIFT */
747 #define IGC_TTQF_PROTOCOL_TCP		0x0
748 /* TTQF UDP Bit, shift with IGC_TTQF_PROTOCOL_SHIFT */
749 #define IGC_TTQF_PROTOCOL_UDP		0x1
750 /* TTQF SCTP Bit, shift with IGC_TTQF_PROTOCOL_SHIFT */
751 #define IGC_TTQF_PROTOCOL_SCTP		0x2
752 #define IGC_TTQF_PROTOCOL_SHIFT		5       /* TTQF Protocol Shift */
753 #define IGC_TTQF_QUEUE_SHIFT		16      /* TTQF Queue Shfit */
754 #define IGC_TTQF_RX_QUEUE_MASK		0x70000 /* TTQF Queue Mask */
755 #define IGC_TTQF_MASK_ENABLE		0x10000000 /* TTQF Mask Enable Bit */
756 #define IGC_IMIR_CLEAR_MASK		0xF001FFFF /* IMIR Reg Clear Mask */
757 #define IGC_IMIR_PORT_BYPASS		0x20000 /* IMIR Port Bypass Bit */
758 #define IGC_IMIR_PRIORITY_SHIFT		29 /* IMIR Priority Shift */
759 #define IGC_IMIREXT_CLEAR_MASK		0x7FFFF /* IMIREXT Reg Clear Mask */
760 
761 #define IGC_MDICNFG_EXT_MDIO		0x80000000 /* MDI ext/int destination */
762 #define IGC_MDICNFG_COM_MDIO		0x40000000 /* MDI shared w/ lan 0 */
763 #define IGC_MDICNFG_PHY_MASK		0x03E00000
764 #define IGC_MDICNFG_PHY_SHIFT		21
765 
766 #define IGC_MEDIA_PORT_COPPER			1
767 #define IGC_MEDIA_PORT_OTHER			2
768 #define IGC_M88E1112_AUTO_COPPER_SGMII		0x2
769 #define IGC_M88E1112_AUTO_COPPER_BASEX		0x3
770 #define IGC_M88E1112_STATUS_LINK		0x0004 /* Interface Link Bit */
771 #define IGC_M88E1112_MAC_CTRL_1			0x10
772 #define IGC_M88E1112_MAC_CTRL_1_MODE_MASK	0x0380 /* Mode Select */
773 #define IGC_M88E1112_MAC_CTRL_1_MODE_SHIFT	7
774 #define IGC_M88E1112_PAGE_ADDR			0x16
775 #define IGC_M88E1112_STATUS			0x01
776 
777 #define IGC_THSTAT_LOW_EVENT		0x20000000 /* Low thermal threshold */
778 #define IGC_THSTAT_MID_EVENT		0x00200000 /* Mid thermal threshold */
779 #define IGC_THSTAT_HIGH_EVENT		0x00002000 /* High thermal threshold */
780 #define IGC_THSTAT_PWR_DOWN		0x00000001 /* Power Down Event */
781 #define IGC_THSTAT_LINK_THROTTLE	0x00000002 /* Link Spd Throttle Event */
782 
783 /* EEE defines */
784 #define IGC_IPCNFG_EEE_2_5G_AN		0x00000010 /* IPCNFG EEE Ena 2.5G AN */
785 #define IGC_IPCNFG_EEE_1G_AN		0x00000008 /* IPCNFG EEE Ena 1G AN */
786 #define IGC_IPCNFG_EEE_100M_AN		0x00000004 /* IPCNFG EEE Ena 100M AN */
787 #define IGC_EEER_TX_LPI_EN		0x00010000 /* EEER Tx LPI Enable */
788 #define IGC_EEER_RX_LPI_EN		0x00020000 /* EEER Rx LPI Enable */
789 #define IGC_EEER_LPI_FC			0x00040000 /* EEER Ena on Flow Cntrl */
790 /* EEE status */
791 #define IGC_EEER_EEE_NEG		0x20000000 /* EEE capability nego */
792 #define IGC_EEER_RX_LPI_STATUS		0x40000000 /* Rx in LPI state */
793 #define IGC_EEER_TX_LPI_STATUS		0x80000000 /* Tx in LPI state */
794 #define IGC_EEE_LP_ADV_ADDR_I350	0x040F     /* EEE LP Advertisement */
795 #define IGC_M88E1543_PAGE_ADDR		0x16       /* Page Offset Register */
796 #define IGC_M88E1543_EEE_CTRL_1		0x0
797 #define IGC_M88E1543_EEE_CTRL_1_MS	0x0001     /* EEE Master/Slave */
798 #define IGC_M88E1543_FIBER_CTRL		0x0        /* Fiber Control Register */
799 #define IGC_EEE_ADV_DEV_I354		7
800 #define IGC_EEE_ADV_ADDR_I354		60
801 #define IGC_EEE_ADV_100_SUPPORTED	(1 << 1)   /* 100BaseTx EEE Supported */
802 #define IGC_EEE_ADV_1000_SUPPORTED	(1 << 2)   /* 1000BaseT EEE Supported */
803 #define IGC_PCS_STATUS_DEV_I354		3
804 #define IGC_PCS_STATUS_ADDR_I354	1
805 #define IGC_PCS_STATUS_RX_LPI_RCVD	0x0400
806 #define IGC_PCS_STATUS_TX_LPI_RCVD	0x0800
807 #define IGC_M88E1512_CFG_REG_1		0x0010
808 #define IGC_M88E1512_CFG_REG_2		0x0011
809 #define IGC_M88E1512_CFG_REG_3		0x0007
810 #define IGC_M88E1512_MODE		0x0014
811 #define IGC_EEE_SU_LPI_CLK_STP		0x00800000 /* EEE LPI Clock Stop */
812 #define IGC_EEE_LP_ADV_DEV_I225		7          /* EEE LP Adv Device */
813 #define IGC_EEE_LP_ADV_ADDR_I225	61         /* EEE LP Adv Register */
814 
815 #define IGC_MMDAC_FUNC_DATA		0x4000 /* Data, no post increment */
816 
817 /* PHY Control Register */
818 #define MII_CR_SPEED_SELECT_MSB	0x0040  /* bits 6,13: 10=1000, 01=100, 00=10 */
819 #define MII_CR_COLL_TEST_ENABLE	0x0080  /* Collision test enable */
820 #define MII_CR_FULL_DUPLEX	0x0100  /* FDX =1, half duplex =0 */
821 #define MII_CR_RESTART_AUTO_NEG	0x0200  /* Restart auto negotiation */
822 #define MII_CR_ISOLATE		0x0400  /* Isolate PHY from MII */
823 #define MII_CR_POWER_DOWN	0x0800  /* Power down */
824 #define MII_CR_AUTO_NEG_EN	0x1000  /* Auto Neg Enable */
825 #define MII_CR_SPEED_SELECT_LSB	0x2000  /* bits 6,13: 10=1000, 01=100, 00=10 */
826 #define MII_CR_LOOPBACK		0x4000  /* 0 = normal, 1 = loopback */
827 #define MII_CR_RESET		0x8000  /* 0 = normal, 1 = PHY reset */
828 #define MII_CR_SPEED_1000	0x0040
829 #define MII_CR_SPEED_100	0x2000
830 #define MII_CR_SPEED_10		0x0000
831 
832 /* PHY Status Register */
833 #define MII_SR_EXTENDED_CAPS	0x0001 /* Extended register capabilities */
834 #define MII_SR_JABBER_DETECT	0x0002 /* Jabber Detected */
835 #define MII_SR_LINK_STATUS	0x0004 /* Link Status 1 = link */
836 #define MII_SR_AUTONEG_CAPS	0x0008 /* Auto Neg Capable */
837 #define MII_SR_REMOTE_FAULT	0x0010 /* Remote Fault Detect */
838 #define MII_SR_AUTONEG_COMPLETE	0x0020 /* Auto Neg Complete */
839 #define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */
840 #define MII_SR_EXTENDED_STATUS	0x0100 /* Ext. status info in Reg 0x0F */
841 #define MII_SR_100T2_HD_CAPS	0x0200 /* 100T2 Half Duplex Capable */
842 #define MII_SR_100T2_FD_CAPS	0x0400 /* 100T2 Full Duplex Capable */
843 #define MII_SR_10T_HD_CAPS	0x0800 /* 10T   Half Duplex Capable */
844 #define MII_SR_10T_FD_CAPS	0x1000 /* 10T   Full Duplex Capable */
845 #define MII_SR_100X_HD_CAPS	0x2000 /* 100X  Half Duplex Capable */
846 #define MII_SR_100X_FD_CAPS	0x4000 /* 100X  Full Duplex Capable */
847 #define MII_SR_100T4_CAPS	0x8000 /* 100T4 Capable */
848 
849 /* Autoneg Advertisement Register */
850 #define NWAY_AR_SELECTOR_FIELD	0x0001   /* indicates IEEE 802.3 CSMA/CD */
851 #define NWAY_AR_10T_HD_CAPS	0x0020   /* 10T   Half Duplex Capable */
852 #define NWAY_AR_10T_FD_CAPS	0x0040   /* 10T   Full Duplex Capable */
853 #define NWAY_AR_100TX_HD_CAPS	0x0080   /* 100TX Half Duplex Capable */
854 #define NWAY_AR_100TX_FD_CAPS	0x0100   /* 100TX Full Duplex Capable */
855 #define NWAY_AR_100T4_CAPS	0x0200   /* 100T4 Capable */
856 #define NWAY_AR_PAUSE		0x0400   /* Pause operation desired */
857 #define NWAY_AR_ASM_DIR		0x0800   /* Asymmetric Pause Direction bit */
858 #define NWAY_AR_REMOTE_FAULT	0x2000   /* Remote Fault detected */
859 #define NWAY_AR_NEXT_PAGE	0x8000   /* Next Page ability supported */
860 
861 /* Link Partner Ability Register (Base Page) */
862 #define NWAY_LPAR_SELECTOR_FIELD	0x0000 /* LP protocol selector field */
863 #define NWAY_LPAR_10T_HD_CAPS		0x0020 /* LP 10T Half Dplx Capable */
864 #define NWAY_LPAR_10T_FD_CAPS		0x0040 /* LP 10T Full Dplx Capable */
865 #define NWAY_LPAR_100TX_HD_CAPS		0x0080 /* LP 100TX Half Dplx Capable */
866 #define NWAY_LPAR_100TX_FD_CAPS		0x0100 /* LP 100TX Full Dplx Capable */
867 #define NWAY_LPAR_100T4_CAPS		0x0200 /* LP is 100T4 Capable */
868 #define NWAY_LPAR_PAUSE			0x0400 /* LP Pause operation desired */
869 #define NWAY_LPAR_ASM_DIR		0x0800 /* LP Asym Pause Direction bit */
870 #define NWAY_LPAR_REMOTE_FAULT		0x2000 /* LP detected Remote Fault */
871 #define NWAY_LPAR_ACKNOWLEDGE		0x4000 /* LP rx'd link code word */
872 #define NWAY_LPAR_NEXT_PAGE		0x8000 /* Next Page ability supported */
873 
874 /* Autoneg Expansion Register */
875 #define NWAY_ER_LP_NWAY_CAPS		0x0001 /* LP has Auto Neg Capability */
876 #define NWAY_ER_PAGE_RXD		0x0002 /* LP 10T Half Dplx Capable */
877 #define NWAY_ER_NEXT_PAGE_CAPS		0x0004 /* LP 10T Full Dplx Capable */
878 #define NWAY_ER_LP_NEXT_PAGE_CAPS	0x0008 /* LP 100TX Half Dplx Capable */
879 #define NWAY_ER_PAR_DETECT_FAULT	0x0010 /* LP 100TX Full Dplx Capable */
880 
881 /* 1000BASE-T Control Register */
882 #define CR_1000T_ASYM_PAUSE	0x0080 /* Advertise asymmetric pause bit */
883 #define CR_1000T_HD_CAPS	0x0100 /* Advertise 1000T HD capability */
884 #define CR_1000T_FD_CAPS	0x0200 /* Advertise 1000T FD capability  */
885 /* 1=Repeater/switch device port 0=DTE device */
886 #define CR_1000T_REPEATER_DTE	0x0400
887 /* 1=Configure PHY as Master 0=Configure PHY as Slave */
888 #define CR_1000T_MS_VALUE	0x0800
889 /* 1=Master/Slave manual config value 0=Automatic Master/Slave config */
890 #define CR_1000T_MS_ENABLE	0x1000
891 #define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */
892 #define CR_1000T_TEST_MODE_1	0x2000 /* Transmit Waveform test */
893 #define CR_1000T_TEST_MODE_2	0x4000 /* Master Transmit Jitter test */
894 #define CR_1000T_TEST_MODE_3	0x6000 /* Slave Transmit Jitter test */
895 #define CR_1000T_TEST_MODE_4	0x8000 /* Transmitter Distortion test */
896 
897 /* 1000BASE-T Status Register */
898 #define SR_1000T_IDLE_ERROR_CNT		0x00FF /* Num idle err since last rd */
899 #define SR_1000T_ASYM_PAUSE_DIR		0x0100 /* LP asym pause direction bit */
900 #define SR_1000T_LP_HD_CAPS		0x0400 /* LP is 1000T HD capable */
901 #define SR_1000T_LP_FD_CAPS		0x0800 /* LP is 1000T FD capable */
902 #define SR_1000T_REMOTE_RX_STATUS	0x1000 /* Remote receiver OK */
903 #define SR_1000T_LOCAL_RX_STATUS	0x2000 /* Local receiver OK */
904 #define SR_1000T_MS_CONFIG_RES		0x4000 /* 1=Local Tx Master, 0=Slave */
905 #define SR_1000T_MS_CONFIG_FAULT	0x8000 /* Master/Slave config fault */
906 
907 #define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT	5
908 
909 /* PHY 1000 MII Register/Bit Definitions */
910 /* PHY Registers defined by IEEE */
911 #define PHY_CONTROL		0x00 /* Control Register */
912 #define PHY_STATUS		0x01 /* Status Register */
913 #define PHY_ID1			0x02 /* Phy Id Reg (word 1) */
914 #define PHY_ID2			0x03 /* Phy Id Reg (word 2) */
915 #define PHY_AUTONEG_ADV		0x04 /* Autoneg Advertisement */
916 #define PHY_LP_ABILITY		0x05 /* Link Partner Ability (Base Page) */
917 #define PHY_AUTONEG_EXP		0x06 /* Autoneg Expansion Reg */
918 #define PHY_NEXT_PAGE_TX	0x07 /* Next Page Tx */
919 #define PHY_LP_NEXT_PAGE	0x08 /* Link Partner Next Page */
920 #define PHY_1000T_CTRL		0x09 /* 1000Base-T Control Reg */
921 #define PHY_1000T_STATUS	0x0A /* 1000Base-T Status Reg */
922 #define PHY_EXT_STATUS		0x0F /* Extended Status Reg */
923 
924 /* PHY GPY 211 registers */
925 #define STANDARD_AN_REG_MASK	0x0007 /* MMD */
926 #define ANEG_MULTIGBT_AN_CTRL	0x0020 /* MULTI GBT AN Control Register */
927 #define MMD_DEVADDR_SHIFT	16     /* Shift MMD to higher bits */
928 #define CR_2500T_FD_CAPS	0x0080 /* Advertise 2500T FD capability */
929 
930 #define PHY_CONTROL_LB		0x4000 /* PHY Loopback bit */
931 
932 /* NVM Control */
933 #define IGC_EECD_SK		0x00000001 /* NVM Clock */
934 #define IGC_EECD_CS		0x00000002 /* NVM Chip Select */
935 #define IGC_EECD_DI		0x00000004 /* NVM Data In */
936 #define IGC_EECD_DO		0x00000008 /* NVM Data Out */
937 #define IGC_EECD_REQ		0x00000040 /* NVM Access Request */
938 #define IGC_EECD_GNT		0x00000080 /* NVM Access Grant */
939 #define IGC_EECD_PRES		0x00000100 /* NVM Present */
940 #define IGC_EECD_SIZE		0x00000200 /* NVM Size (0=64 word 1=256 word) */
941 /* NVM Addressing bits based on type 0=small, 1=large */
942 #define IGC_EECD_ADDR_BITS	0x00000400
943 #define IGC_NVM_GRANT_ATTEMPTS	1000 /* NVM # attempts to gain grant */
944 #define IGC_EECD_AUTO_RD	0x00000200  /* NVM Auto Read done */
945 #define IGC_EECD_SIZE_EX_MASK	0x00007800  /* NVM Size */
946 #define IGC_EECD_SIZE_EX_SHIFT	11
947 #define IGC_EECD_FLUPD		0x00080000 /* Update FLASH */
948 #define IGC_EECD_AUPDEN		0x00100000 /* Ena Auto FLASH update */
949 #define IGC_EECD_SEC1VAL	0x00400000 /* Sector One Valid */
950 #define IGC_EECD_SEC1VAL_VALID_MASK	(IGC_EECD_AUTO_RD | IGC_EECD_PRES)
951 
952 #define IGC_EECD_FLUPD_I225		0x00800000 /* Update FLASH */
953 #define IGC_EECD_FLUDONE_I225		0x04000000 /* Update FLASH done */
954 #define IGC_EECD_FLASH_DETECTED_I225	0x00080000 /* FLASH detected */
955 #define IGC_FLUDONE_ATTEMPTS		20000
956 #define IGC_EERD_EEWR_MAX_COUNT		512 /* buffered EEPROM words rw */
957 #define IGC_EECD_SEC1VAL_I225		0x02000000 /* Sector One Valid */
958 #define IGC_FLSECU_BLK_SW_ACCESS_I225	0x00000004 /* Block SW access */
959 #define IGC_FWSM_FW_VALID_I225		0x8000 /* FW valid bit */
960 
961 #define IGC_NVM_RW_REG_DATA	16  /* Offset to data in NVM read/write regs */
962 #define IGC_NVM_RW_REG_DONE	2   /* Offset to READ/WRITE done bit */
963 #define IGC_NVM_RW_REG_START	1   /* Start operation */
964 #define IGC_NVM_RW_ADDR_SHIFT	2   /* Shift to the address bits */
965 #define IGC_NVM_POLL_WRITE	1   /* Flag for polling for write complete */
966 #define IGC_NVM_POLL_READ	0   /* Flag for polling for read complete */
967 #define IGC_FLASH_UPDATES	2000
968 
969 /* NVM Word Offsets */
970 #define NVM_COMPAT				0x0003
971 #define NVM_ID_LED_SETTINGS			0x0004
972 #define NVM_VERSION				0x0005
973 #define NVM_FUTURE_INIT_WORD1			0x0019
974 #define NVM_COMPAT_VALID_CSUM			0x0001
975 #define NVM_FUTURE_INIT_WORD1_VALID_CSUM	0x0040
976 #define NVM_ETRACK_WORD				0x0042
977 #define NVM_ETRACK_HIWORD			0x0043
978 #define NVM_COMB_VER_OFF			0x0083
979 #define NVM_COMB_VER_PTR			0x003d
980 
981 /* NVM version defines */
982 #define NVM_MAJOR_MASK			0xF000
983 #define NVM_MINOR_MASK			0x0FF0
984 #define NVM_IMAGE_ID_MASK		0x000F
985 #define NVM_COMB_VER_MASK		0x00FF
986 #define NVM_MAJOR_SHIFT			12
987 #define NVM_MINOR_SHIFT			4
988 #define NVM_COMB_VER_SHFT		8
989 #define NVM_VER_INVALID			0xFFFF
990 #define NVM_ETRACK_SHIFT		16
991 #define NVM_ETRACK_VALID		0x8000
992 #define NVM_NEW_DEC_MASK		0x0F00
993 #define NVM_HEX_CONV			16
994 #define NVM_HEX_TENS			10
995 
996 #define NVM_INIT_CONTROL2_REG		0x000F
997 #define NVM_INIT_CONTROL3_PORT_B	0x0014
998 #define NVM_INIT_3GIO_3			0x001A
999 #define NVM_SWDEF_PINS_CTRL_PORT_0	0x0020
1000 #define NVM_INIT_CONTROL3_PORT_A	0x0024
1001 #define NVM_CFG				0x0012
1002 #define NVM_ALT_MAC_ADDR_PTR		0x0037
1003 #define NVM_CHECKSUM_REG		0x003F
1004 
1005 #define IGC_NVM_CFG_DONE_PORT_0	0x040000 /* MNG config cycle done */
1006 #define IGC_NVM_CFG_DONE_PORT_1	0x080000 /* ...for second port */
1007 
1008 /* Mask bits for fields in Word 0x0f of the NVM */
1009 #define NVM_WORD0F_PAUSE_MASK		0x3000
1010 #define NVM_WORD0F_PAUSE		0x1000
1011 #define NVM_WORD0F_ASM_DIR		0x2000
1012 
1013 /* Mask bits for fields in Word 0x1a of the NVM */
1014 #define NVM_WORD1A_ASPM_MASK		0x000C
1015 
1016 /* Mask bits for fields in Word 0x03 of the EEPROM */
1017 #define NVM_COMPAT_LOM			0x0800
1018 
1019 /* length of string needed to store PBA number */
1020 #define IGC_PBANUM_LENGTH		11
1021 
1022 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
1023 #define NVM_SUM				0xBABA
1024 
1025 /* PBA (printed board assembly) number words */
1026 #define NVM_PBA_OFFSET_0		8
1027 #define NVM_PBA_OFFSET_1		9
1028 #define NVM_PBA_PTR_GUARD		0xFAFA
1029 #define NVM_WORD_SIZE_BASE_SHIFT	6
1030 
1031 /* NVM Commands - Microwire */
1032 #define NVM_READ_OPCODE_MICROWIRE	0x6  /* NVM read opcode */
1033 #define NVM_WRITE_OPCODE_MICROWIRE	0x5  /* NVM write opcode */
1034 #define NVM_ERASE_OPCODE_MICROWIRE	0x7  /* NVM erase opcode */
1035 #define NVM_EWEN_OPCODE_MICROWIRE	0x13 /* NVM erase/write enable */
1036 #define NVM_EWDS_OPCODE_MICROWIRE	0x10 /* NVM erase/write disable */
1037 
1038 /* NVM Commands - SPI */
1039 #define NVM_MAX_RETRY_SPI	5000 /* Max wait of 5ms, for RDY signal */
1040 #define NVM_READ_OPCODE_SPI	0x03 /* NVM read opcode */
1041 #define NVM_WRITE_OPCODE_SPI	0x02 /* NVM write opcode */
1042 #define NVM_A8_OPCODE_SPI	0x08 /* opcode bit-3 = address bit-8 */
1043 #define NVM_WREN_OPCODE_SPI	0x06 /* NVM set Write Enable latch */
1044 #define NVM_RDSR_OPCODE_SPI	0x05 /* NVM read Status register */
1045 
1046 /* SPI NVM Status Register */
1047 #define NVM_STATUS_RDY_SPI	0x01
1048 
1049 /* Word definitions for ID LED Settings */
1050 #define ID_LED_RESERVED_0000	0x0000
1051 #define ID_LED_RESERVED_FFFF	0xFFFF
1052 #define ID_LED_DEFAULT		((ID_LED_OFF1_ON2  << 12) | \
1053 				 (ID_LED_OFF1_OFF2 <<  8) | \
1054 				 (ID_LED_DEF1_DEF2 <<  4) | \
1055 				 (ID_LED_DEF1_DEF2))
1056 #define ID_LED_DEF1_DEF2	0x1
1057 #define ID_LED_DEF1_ON2		0x2
1058 #define ID_LED_DEF1_OFF2	0x3
1059 #define ID_LED_ON1_DEF2		0x4
1060 #define ID_LED_ON1_ON2		0x5
1061 #define ID_LED_ON1_OFF2		0x6
1062 #define ID_LED_OFF1_DEF2	0x7
1063 #define ID_LED_OFF1_ON2		0x8
1064 #define ID_LED_OFF1_OFF2	0x9
1065 
1066 #define IGP_ACTIVITY_LED_MASK	0xFFFFF0FF
1067 #define IGP_ACTIVITY_LED_ENABLE	0x0300
1068 #define IGP_LED3_MODE		0x07000000
1069 
1070 /* PCI/PCI-X/PCI-EX Config space */
1071 #define PCIX_COMMAND_REGISTER		0xE6
1072 #define PCIX_STATUS_REGISTER_LO		0xE8
1073 #define PCIX_STATUS_REGISTER_HI		0xEA
1074 #define PCI_HEADER_TYPE_REGISTER	0x0E
1075 #define PCIE_LINK_STATUS		0x12
1076 
1077 #define PCIX_COMMAND_MMRBC_MASK		0x000C
1078 #define PCIX_COMMAND_MMRBC_SHIFT	0x2
1079 #define PCIX_STATUS_HI_MMRBC_MASK	0x0060
1080 #define PCIX_STATUS_HI_MMRBC_SHIFT	0x5
1081 #define PCIX_STATUS_HI_MMRBC_4K		0x3
1082 #define PCIX_STATUS_HI_MMRBC_2K		0x2
1083 #define PCIX_STATUS_LO_FUNC_MASK	0x7
1084 #define PCI_HEADER_TYPE_MULTIFUNC	0x80
1085 #define PCIE_LINK_WIDTH_MASK		0x3F0
1086 #define PCIE_LINK_WIDTH_SHIFT		4
1087 #define PCIE_LINK_SPEED_MASK		0x0F
1088 #define PCIE_LINK_SPEED_2500		0x01
1089 #define PCIE_LINK_SPEED_5000		0x02
1090 
1091 #ifndef ETH_ADDR_LEN
1092 #define ETH_ADDR_LEN			6
1093 #endif
1094 
1095 #define PHY_REVISION_MASK		0xFFFFFFF0
1096 #define MAX_PHY_REG_ADDRESS		0x1F  /* 5 bit address bus (0-0x1F) */
1097 #define MAX_PHY_MULTI_PAGE_REG		0xF
1098 
1099 /* Bit definitions for valid PHY IDs.
1100  * I = Integrated
1101  * E = External
1102  */
1103 #define M88IGC_E_PHY_ID		0x01410C50
1104 #define M88IGC_I_PHY_ID		0x01410C30
1105 #define M88E1011_I_PHY_ID	0x01410C20
1106 #define IGP01IGC_I_PHY_ID	0x02A80380
1107 #define M88E1111_I_PHY_ID	0x01410CC0
1108 #define GG82563_E_PHY_ID	0x01410CA0
1109 #define IGP03IGC_E_PHY_ID	0x02A80390
1110 #define IFE_E_PHY_ID		0x02A80330
1111 #define IFE_PLUS_E_PHY_ID	0x02A80320
1112 #define IFE_C_E_PHY_ID		0x02A80310
1113 #define I225_I_PHY_ID		0x67C9DC00
1114 
1115 /* M88IGC Specific Registers */
1116 #define M88IGC_PHY_SPEC_CTRL		0x10  /* PHY Specific Control Reg */
1117 #define M88IGC_PHY_SPEC_STATUS		0x11  /* PHY Specific Status Reg */
1118 #define M88IGC_EXT_PHY_SPEC_CTRL	0x14  /* Extended PHY Specific Cntrl */
1119 #define M88IGC_RX_ERR_CNTR		0x15  /* Receive Error Counter */
1120 
1121 #define M88IGC_PHY_PAGE_SELECT	0x1D  /* Reg 29 for pg number setting */
1122 #define M88IGC_PHY_GEN_CONTROL	0x1E  /* meaning depends on reg 29 */
1123 
1124 /* M88IGC PHY Specific Control Register */
1125 #define M88IGC_PSCR_POLARITY_REVERSAL	0x0002 /* 1=Polarity Reverse enabled */
1126 /* MDI Crossover Mode bits 6:5 Manual MDI configuration */
1127 #define M88IGC_PSCR_MDI_MANUAL_MODE	0x0000
1128 #define M88IGC_PSCR_MDIX_MANUAL_MODE	0x0020  /* Manual MDIX configuration */
1129 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
1130 #define M88IGC_PSCR_AUTO_X_1000T	0x0040
1131 /* Auto crossover enabled all speeds */
1132 #define M88IGC_PSCR_AUTO_X_MODE		0x0060
1133 #define M88IGC_PSCR_ASSERT_CRS_ON_TX	0x0800 /* 1=Assert CRS on Tx */
1134 
1135 /* M88IGC PHY Specific Status Register */
1136 #define M88IGC_PSSR_REV_POLARITY	0x0002 /* 1=Polarity reversed */
1137 #define M88IGC_PSSR_DOWNSHIFT		0x0020 /* 1=Downshifted */
1138 #define M88IGC_PSSR_MDIX		0x0040 /* 1=MDIX; 0=MDI */
1139 /* 0 = <50M
1140  * 1 = 50-80M
1141  * 2 = 80-110M
1142  * 3 = 110-140M
1143  * 4 = >140M
1144  */
1145 #define M88IGC_PSSR_CABLE_LENGTH	0x0380
1146 #define M88IGC_PSSR_LINK		0x0400 /* 1=Link up, 0=Link down */
1147 #define M88IGC_PSSR_SPD_DPLX_RESOLVED	0x0800 /* 1=Speed & Duplex resolved */
1148 #define M88IGC_PSSR_SPEED		0xC000 /* Speed, bits 14:15 */
1149 #define M88IGC_PSSR_1000MBS		0x8000 /* 10=1000Mbs */
1150 
1151 #define M88IGC_PSSR_CABLE_LENGTH_SHIFT	7
1152 
1153 /* Number of times we will attempt to autonegotiate before downshifting if we
1154  * are the master
1155  */
1156 #define M88IGC_EPSCR_MASTER_DOWNSHIFT_MASK	0x0C00
1157 #define M88IGC_EPSCR_MASTER_DOWNSHIFT_1X	0x0000
1158 /* Number of times we will attempt to autonegotiate before downshifting if we
1159  * are the slave
1160  */
1161 #define M88IGC_EPSCR_SLAVE_DOWNSHIFT_MASK	0x0300
1162 #define M88IGC_EPSCR_SLAVE_DOWNSHIFT_1X		0x0100
1163 #define M88IGC_EPSCR_TX_CLK_25			0x0070 /* 25  MHz TX_CLK */
1164 
1165 
1166 /* M88EC018 Rev 2 specific DownShift settings */
1167 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK	0x0E00
1168 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X	0x0800
1169 
1170 /* Bits...
1171  * 15-5: page
1172  * 4-0: register offset
1173  */
1174 #define GG82563_PAGE_SHIFT	5
1175 #define GG82563_REG(page, reg)	\
1176 	(((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
1177 #define GG82563_MIN_ALT_REG	30
1178 
1179 /* GG82563 Specific Registers */
1180 #define GG82563_PHY_SPEC_CTRL		GG82563_REG(0, 16) /* PHY Spec Cntrl */
1181 #define GG82563_PHY_PAGE_SELECT		GG82563_REG(0, 22) /* Page Select */
1182 #define GG82563_PHY_SPEC_CTRL_2		GG82563_REG(0, 26) /* PHY Spec Cntrl2 */
1183 #define GG82563_PHY_PAGE_SELECT_ALT	GG82563_REG(0, 29) /* Alt Page Select */
1184 
1185 /* MAC Specific Control Register */
1186 #define GG82563_PHY_MAC_SPEC_CTRL	GG82563_REG(2, 21)
1187 
1188 #define GG82563_PHY_DSP_DISTANCE	GG82563_REG(5, 26) /* DSP Distance */
1189 
1190 /* Page 193 - Port Control Registers */
1191 /* Kumeran Mode Control */
1192 #define GG82563_PHY_KMRN_MODE_CTRL	GG82563_REG(193, 16)
1193 #define GG82563_PHY_PWR_MGMT_CTRL	GG82563_REG(193, 20) /* Pwr Mgt Ctrl */
1194 
1195 /* Page 194 - KMRN Registers */
1196 #define GG82563_PHY_INBAND_CTRL		GG82563_REG(194, 18) /* Inband Ctrl */
1197 
1198 /* MDI Control */
1199 #define IGC_MDIC_DATA_MASK	0x0000FFFF
1200 #define IGC_MDIC_INT_EN		0x20000000
1201 #define IGC_MDIC_REG_MASK	0x001F0000
1202 #define IGC_MDIC_REG_SHIFT	16
1203 #define IGC_MDIC_PHY_SHIFT	21
1204 #define IGC_MDIC_OP_WRITE	0x04000000
1205 #define IGC_MDIC_OP_READ	0x08000000
1206 #define IGC_MDIC_READY		0x10000000
1207 #define IGC_MDIC_ERROR		0x40000000
1208 
1209 #define IGC_N0_QUEUE 		-1
1210 
1211 #define IGC_MAX_MAC_HDR_LEN	127
1212 #define IGC_MAX_NETWORK_HDR_LEN	511
1213 
1214 #define IGC_VLANPQF_QUEUE_SEL(_n, q_idx) ((q_idx) << ((_n) * 4))
1215 #define IGC_VLANPQF_P_VALID(_n)	(0x1 << (3 + (_n) * 4))
1216 #define IGC_VLANPQF_QUEUE_MASK	0x03
1217 #define IGC_VFTA_BLOCK_SIZE	8
1218 /* SerDes Control */
1219 #define IGC_GEN_POLL_TIMEOUT	640
1220 
1221 /* DMA Coalescing register fields */
1222 /* DMA Coalescing Watchdog Timer */
1223 #define IGC_DMACR_DMACWT_MASK	0x00003FFF
1224 /* DMA Coalescing Rx Threshold */
1225 #define IGC_DMACR_DMACTHR_MASK	0x00FF0000
1226 #define IGC_DMACR_DMACTHR_SHIFT	16
1227 /* Lx when no PCIe transactions */
1228 #define IGC_DMACR_DMAC_LX_MASK	0x30000000
1229 #define IGC_DMACR_DMAC_LX_SHIFT	28
1230 #define IGC_DMACR_DMAC_EN	0x80000000 /* Enable DMA Coalescing */
1231 /* DMA Coalescing BMC-to-OS Watchdog Enable */
1232 #define IGC_DMACR_DC_BMC2OSW_EN	0x00008000
1233 
1234 /* DMA Coalescing Transmit Threshold */
1235 #define IGC_DMCTXTH_DMCTTHR_MASK	0x00000FFF
1236 
1237 #define IGC_DMCTLX_TTLX_MASK	0x00000FFF /* Time to LX request */
1238 
1239 /* Rx Traffic Rate Threshold */
1240 #define IGC_DMCRTRH_UTRESH_MASK		0x0007FFFF
1241 /* Rx packet rate in current window */
1242 #define IGC_DMCRTRH_LRPRCW		0x80000000
1243 
1244 /* DMA Coal Rx Traffic Current Count */
1245 #define IGC_DMCCNT_CCOUNT_MASK		0x01FFFFFF
1246 
1247 /* Flow ctrl Rx Threshold High val */
1248 #define IGC_FCRTC_RTH_COAL_MASK		0x0003FFF0
1249 #define IGC_FCRTC_RTH_COAL_SHIFT	4
1250 /* Lx power decision based on DMA coal */
1251 #define IGC_PCIEMISC_LX_DECISION	0x00000080
1252 
1253 #define IGC_RXPBS_CFG_TS_EN		0x80000000 /* Timestamp in Rx buffer */
1254 #define IGC_RXPBS_SIZE_I210_MASK	0x0000003F /* Rx packet buffer size */
1255 #define IGC_TXPB0S_SIZE_I210_MASK	0x0000003F /* Tx packet buffer 0 size */
1256 #define I210_RXPBSIZE_DEFAULT		0x000000A2 /* RXPBSIZE default */
1257 #define I210_TXPBSIZE_DEFAULT		0x04000014 /* TXPBSIZE default */
1258 
1259 #define IGC_LTRC_EEEMS_EN		0x00000020 /* Enable EEE LTR max send */
1260 /* Minimum time for 1000BASE-T where no data will be transmit following move out
1261  * of EEE LPI Tx state
1262  */
1263 #define IGC_TW_SYSTEM_1000_MASK		0x000000FF
1264 /* Minimum time for 100BASE-T where no data will be transmit following move out
1265  * of EEE LPI Tx state
1266  */
1267 #define IGC_TW_SYSTEM_100_MASK		0x0000FF00
1268 #define IGC_TW_SYSTEM_100_SHIFT		8
1269 #define IGC_LTRMINV_LTRV_MASK		0x000003FF /* LTR minimum value */
1270 #define IGC_LTRMAXV_LTRV_MASK		0x000003FF /* LTR maximum value */
1271 #define IGC_LTRMINV_SCALE_MASK		0x00001C00 /* LTR minimum scale */
1272 #define IGC_LTRMINV_SCALE_SHIFT		10
1273 /* Reg val to set scale to 1024 nsec */
1274 #define IGC_LTRMINV_SCALE_1024		2
1275 /* Reg val to set scale to 32768 nsec */
1276 #define IGC_LTRMINV_SCALE_32768		3
1277 #define IGC_LTRMINV_LSNP_REQ		0x00008000 /* LTR Snoop Requirement */
1278 #define IGC_LTRMAXV_SCALE_MASK		0x00001C00 /* LTR maximum scale */
1279 #define IGC_LTRMAXV_SCALE_SHIFT		10
1280 /* Reg val to set scale to 1024 nsec */
1281 #define IGC_LTRMAXV_SCALE_1024		2
1282 /* Reg val to set scale to 32768 nsec */
1283 #define IGC_LTRMAXV_SCALE_32768		3
1284 #define IGC_LTRMAXV_LSNP_REQ		0x00008000 /* LTR Snoop Requirement */
1285 
1286 #define I225_RXPBSIZE_DEFAULT		0x000000A2 /* RXPBSIZE default */
1287 #define I225_TXPBSIZE_DEFAULT		0x04000014 /* TXPBSIZE default */
1288 #define IGC_RXPBS_SIZE_I225_MASK	0x0000003F /* Rx packet buffer size */
1289 #define IGC_TXPB0S_SIZE_I225_MASK	0x0000003F /* Tx packet buffer 0 size */
1290 #define IGC_STM_OPCODE			0xDB00
1291 #define IGC_EEPROM_FLASH_SIZE_WORD	0x11
1292 #define INVM_DWORD_TO_RECORD_TYPE(invm_dword) \
1293 	(u8)((invm_dword) & 0x7)
1294 #define INVM_DWORD_TO_WORD_ADDRESS(invm_dword) \
1295 	(u8)(((invm_dword) & 0x0000FE00) >> 9)
1296 #define INVM_DWORD_TO_WORD_DATA(invm_dword) \
1297 	(u16)(((invm_dword) & 0xFFFF0000) >> 16)
1298 #define IGC_INVM_RSA_KEY_SHA256_DATA_SIZE_IN_DWORDS	8
1299 #define IGC_INVM_CSR_AUTOLOAD_DATA_SIZE_IN_DWORDS	1
1300 #define IGC_INVM_ULT_BYTES_SIZE		8
1301 #define IGC_INVM_RECORD_SIZE_IN_BYTES	4
1302 #define IGC_INVM_VER_FIELD_ONE		0x1FF8
1303 #define IGC_INVM_VER_FIELD_TWO		0x7FE000
1304 #define IGC_INVM_IMGTYPE_FIELD		0x1F800000
1305 
1306 #define IGC_INVM_MAJOR_MASK		0x3F0
1307 #define IGC_INVM_MINOR_MASK		0xF
1308 #define IGC_INVM_MAJOR_SHIFT		4
1309 
1310 /* PLL Defines */
1311 #define IGC_PCI_PMCSR			0x44
1312 #define IGC_PCI_PMCSR_D3		0x03
1313 #define IGC_MAX_PLL_TRIES		5
1314 #define IGC_PHY_PLL_UNCONF		0xFF
1315 #define IGC_PHY_PLL_FREQ_PAGE		0xFC0000
1316 #define IGC_PHY_PLL_FREQ_REG		0x000E
1317 #define IGC_INVM_DEFAULT_AL		0x202F
1318 #define IGC_INVM_AUTOLOAD		0x0A
1319 #define IGC_INVM_PLL_WO_VAL		0x0010
1320 
1321 /* Proxy Filter Control Extended */
1322 #define IGC_PROXYFCEX_MDNS		0x00000001 /* mDNS */
1323 #define IGC_PROXYFCEX_MDNS_M		0x00000002 /* mDNS Multicast */
1324 #define IGC_PROXYFCEX_MDNS_U		0x00000004 /* mDNS Unicast */
1325 #define IGC_PROXYFCEX_IPV4_M		0x00000008 /* IPv4 Multicast */
1326 #define IGC_PROXYFCEX_IPV6_M		0x00000010 /* IPv6 Multicast */
1327 #define IGC_PROXYFCEX_IGMP		0x00000020 /* IGMP */
1328 #define IGC_PROXYFCEX_IGMP_M		0x00000040 /* IGMP Multicast */
1329 #define IGC_PROXYFCEX_ARPRES		0x00000080 /* ARP Response */
1330 #define IGC_PROXYFCEX_ARPRES_D		0x00000100 /* ARP Response Directed */
1331 #define IGC_PROXYFCEX_ICMPV4		0x00000200 /* ICMPv4 */
1332 #define IGC_PROXYFCEX_ICMPV4_D		0x00000400 /* ICMPv4 Directed */
1333 #define IGC_PROXYFCEX_ICMPV6		0x00000800 /* ICMPv6 */
1334 #define IGC_PROXYFCEX_ICMPV6_D		0x00001000 /* ICMPv6 Directed */
1335 #define IGC_PROXYFCEX_DNS		0x00002000 /* DNS */
1336 
1337 /* Proxy Filter Control */
1338 #define IGC_PROXYFC_D0			0x00000001 /* Enable offload in D0 */
1339 #define IGC_PROXYFC_EX			0x00000004 /* Directed exact proxy */
1340 #define IGC_PROXYFC_MC			0x00000008 /* Directed MC Proxy */
1341 #define IGC_PROXYFC_BC			0x00000010 /* Broadcast Proxy Enable */
1342 #define IGC_PROXYFC_ARP_DIRECTED	0x00000020 /* Directed ARP Proxy Ena */
1343 #define IGC_PROXYFC_IPV4		0x00000040 /* Directed IPv4 Enable */
1344 #define IGC_PROXYFC_IPV6		0x00000080 /* Directed IPv6 Enable */
1345 #define IGC_PROXYFC_NS			0x00000200 /* IPv6 Neighbor Solicitation */
1346 #define IGC_PROXYFC_NS_DIRECTED		0x00000400 /* Directed NS Proxy Ena */
1347 #define IGC_PROXYFC_ARP			0x00000800 /* ARP Request Proxy Ena */
1348 /* Proxy Status */
1349 #define IGC_PROXYS_CLEAR		0xFFFFFFFF /* Clear */
1350 
1351 /* Firmware Status */
1352 #define IGC_FWSTS_FWRI		0x80000000 /* FW Reset Indication */
1353 /* VF Control */
1354 #define IGC_VTCTRL_RST		0x04000000 /* Reset VF */
1355 
1356 #define IGC_STATUS_LAN_ID_MASK	0x00000000C /* Mask for Lan ID field */
1357 /* Lan ID bit field offset in status register */
1358 #define IGC_STATUS_LAN_ID_OFFSET	2
1359 #define IGC_VFTA_ENTRIES		128
1360 
1361 #define IGC_UNUSEDARG
1362 #ifndef ERROR_REPORT
1363 #define ERROR_REPORT(fmt)	do { } while (0)
1364 #endif /* ERROR_REPORT */
1365 #endif /* _IGC_DEFINES_H_ */
1366