1 /*- 2 * SPDX-License-Identifier: BSD-4-Clause 3 * 4 * Copyright (c) 2003 5 * Bill Paul <wpaul@windriver.com>. All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 3. All advertising materials mentioning features or use of this software 16 * must display the following acknowledgement: 17 * This product includes software developed by Bill Paul. 18 * 4. Neither the name of the author nor the names of any co-contributors 19 * may be used to endorse or promote products derived from this software 20 * without specific prior written permission. 21 * 22 * THIS SOFTWARE IS PROVIDED BY Bill Paul AND CONTRIBUTORS ``AS IS'' AND 23 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 24 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 25 * ARE DISCLAIMED. IN NO EVENT SHALL Bill Paul OR THE VOICES IN HIS HEAD 26 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 27 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 28 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 29 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 30 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 31 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 32 * THE POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35 #ifndef _DEV_MII_RGEPHYREG_H_ 36 #define _DEV_MII_RGEPHYREG_H_ 37 38 #define RGEPHY_8211B 2 39 #define RGEPHY_8211C 3 40 #define RGEPHY_8211F 6 41 #define RGEPHY_8211FVD 8 42 43 /* 44 * RealTek 8169S/8110S gigE PHY registers 45 */ 46 47 #define RGEPHY_MII_BMCR 0x00 48 #define RGEPHY_BMCR_RESET 0x8000 49 #define RGEPHY_BMCR_LOOP 0x4000 50 #define RGEPHY_BMCR_SPD0 0x2000 /* speed select, lower bit */ 51 #define RGEPHY_BMCR_AUTOEN 0x1000 /* Autoneg enabled */ 52 #define RGEPHY_BMCR_PDOWN 0x0800 /* Power down */ 53 #define RGEPHY_BMCR_ISO 0x0400 /* Isolate */ 54 #define RGEPHY_BMCR_STARTNEG 0x0200 /* Restart autoneg */ 55 #define RGEPHY_BMCR_FDX 0x0100 /* Duplex mode */ 56 #define RGEPHY_BMCR_CTEST 0x0080 /* Collision test enable */ 57 #define RGEPHY_BMCR_SPD1 0x0040 /* Speed select, upper bit */ 58 59 #define RGEPHY_S1000 RGEPHY_BMCR_SPD1 /* 1000mbps */ 60 #define RGEPHY_S100 RGEPHY_BMCR_SPD0 /* 100mpbs */ 61 #define RGEPHY_S10 0 /* 10mbps */ 62 63 #define RGEPHY_MII_BMSR 0x01 64 #define RGEPHY_BMSR_100T4 0x8000 /* 100 base T4 capable */ 65 #define RGEPHY_BMSR_100TXFDX 0x4000 /* 100 base Tx full duplex capable */ 66 #define RGEPHY_BMSR_100TXHDX 0x2000 /* 100 base Tx half duplex capable */ 67 #define RGEPHY_BMSR_10TFDX 0x1000 /* 10 base T full duplex capable */ 68 #define RGEPHY_BMSR_10THDX 0x0800 /* 10 base T half duplex capable */ 69 #define RGEPHY_BMSR_100T2FDX 0x0400 /* 100 base T2 full duplex capable */ 70 #define RGEPHY_BMSR_100T2HDX 0x0200 /* 100 base T2 half duplex capable */ 71 #define RGEPHY_BMSR_EXTSTS 0x0100 /* Extended status present */ 72 #define RGEPHY_BMSR_PRESUB 0x0040 /* Preamble surpression */ 73 #define RGEPHY_BMSR_ACOMP 0x0020 /* Autoneg complete */ 74 #define RGEPHY_BMSR_RFAULT 0x0010 /* Remote fault condition occurred */ 75 #define RGEPHY_BMSR_ANEG 0x0008 /* Autoneg capable */ 76 #define RGEPHY_BMSR_LINK 0x0004 /* Link status */ 77 #define RGEPHY_BMSR_JABBER 0x0002 /* Jabber detected */ 78 #define RGEPHY_BMSR_EXT 0x0001 /* Extended capability */ 79 80 #define RGEPHY_MII_ANAR 0x04 81 #define RGEPHY_ANAR_NP 0x8000 /* Next page */ 82 #define RGEPHY_ANAR_RF 0x2000 /* Remote fault */ 83 #define RGEPHY_ANAR_ASP 0x0800 /* Asymmetric Pause */ 84 #define RGEPHY_ANAR_PC 0x0400 /* Pause capable */ 85 #define RGEPHY_ANAR_T4 0x0200 /* local device supports 100bT4 */ 86 #define RGEPHY_ANAR_TX_FD 0x0100 /* local device supports 100bTx FD */ 87 #define RGEPHY_ANAR_TX 0x0080 /* local device supports 100bTx */ 88 #define RGEPHY_ANAR_10_FD 0x0040 /* local device supports 10bT FD */ 89 #define RGEPHY_ANAR_10 0x0020 /* local device supports 10bT */ 90 #define RGEPHY_ANAR_SEL 0x001F /* selector field, 00001=Ethernet */ 91 92 #define RGEPHY_MII_ANLPAR 0x05 93 #define RGEPHY_ANLPAR_NP 0x8000 /* Next page */ 94 #define RGEPHY_ANLPAR_RF 0x2000 /* Remote fault */ 95 #define RGEPHY_ANLPAR_ASP 0x0800 /* Asymmetric Pause */ 96 #define RGEPHY_ANLPAR_PC 0x0400 /* Pause capable */ 97 #define RGEPHY_ANLPAR_T4 0x0200 /* link partner supports 100bT4 */ 98 #define RGEPHY_ANLPAR_TX_FD 0x0100 /* link partner supports 100bTx FD */ 99 #define RGEPHY_ANLPAR_TX 0x0080 /* link partner supports 100bTx */ 100 #define RGEPHY_ANLPAR_10_FD 0x0040 /* link partner supports 10bT FD */ 101 #define RGEPHY_ANLPAR_10 0x0020 /* link partner supports 10bT */ 102 #define RGEPHY_ANLPAR_SEL 0x001F /* selector field, 00001=Ethernet */ 103 104 #define RGEPHY_SEL_TYPE 0x0001 /* ethernet */ 105 106 #define RGEPHY_MII_ANER 0x06 107 #define RGEPHY_ANER_PDF 0x0010 /* Parallel detection fault */ 108 #define RGEPHY_ANER_LPNP 0x0008 /* Link partner can next page */ 109 #define RGEPHY_ANER_NP 0x0004 /* Local PHY can next page */ 110 #define RGEPHY_ANER_RX 0x0002 /* Next page received */ 111 #define RGEPHY_ANER_LPAN 0x0001 /* Link partner autoneg capable */ 112 113 #define RGEPHY_MII_NEXTP 0x07 /* Next page */ 114 115 #define RGEPHY_MII_NEXTP_LP 0x08 /* Next page of link partner */ 116 117 #define RGEPHY_MII_1000CTL 0x09 /* 1000baseT control */ 118 #define RGEPHY_1000CTL_TST 0xE000 /* test modes */ 119 #define RGEPHY_1000CTL_MSE 0x1000 /* Master/Slave manual enable */ 120 #define RGEPHY_1000CTL_MSC 0x0800 /* Master/Slave select */ 121 #define RGEPHY_1000CTL_RD 0x0400 /* Repeater/DTE */ 122 #define RGEPHY_1000CTL_AFD 0x0200 /* Advertise full duplex */ 123 #define RGEPHY_1000CTL_AHD 0x0100 /* Advertise half duplex */ 124 125 #define RGEPHY_TEST_TX_JITTER 0x2000 126 #define RGEPHY_TEST_TX_JITTER_MASTER_MODE 0x4000 127 #define RGEPHY_TEST_TX_JITTER_SLAVE_MODE 0x6000 128 #define RGEPHY_TEST_TX_DISTORTION 0x8000 129 130 #define RGEPHY_MII_1000STS 0x0A /* 1000baseT status */ 131 #define RGEPHY_1000STS_MSF 0x8000 /* Master/slave fault */ 132 #define RGEPHY_1000STS_MSR 0x4000 /* Master/slave result */ 133 #define RGEPHY_1000STS_LRS 0x2000 /* Local receiver status */ 134 #define RGEPHY_1000STS_RRS 0x1000 /* Remote receiver status */ 135 #define RGEPHY_1000STS_LPFD 0x0800 /* Link partner can FD */ 136 #define RGEPHY_1000STS_LPHD 0x0400 /* Link partner can HD */ 137 #define RGEPHY_1000STS_IEC 0x00FF /* Idle error count */ 138 139 #define RGEPHY_MII_EXTSTS 0x0F /* Extended status */ 140 #define RGEPHY_EXTSTS_X_FD_CAP 0x8000 /* 1000base-X FD capable */ 141 #define RGEPHY_EXTSTS_X_HD_CAP 0x4000 /* 1000base-X HD capable */ 142 #define RGEPHY_EXTSTS_T_FD_CAP 0x2000 /* 1000base-T FD capable */ 143 #define RGEPHY_EXTSTS_T_HD_CAP 0x1000 /* 1000base-T HD capable */ 144 145 /* RTL8211B(L)/RTL8211C(L) */ 146 #define RGEPHY_MII_PCR 0x10 /* PHY Specific control register */ 147 #define RGEPHY_PCR_ASSERT_CRS 0x0800 148 #define RGEPHY_PCR_FORCE_LINK 0x0400 149 #define RGEPHY_PCR_MDI_MASK 0x0060 150 #define RGEPHY_PCR_MDIX_AUTO 0x0040 151 #define RGEPHY_PCR_MDIX_MANUAL 0x0020 152 #define RGEPHY_PCR_MDI_MANUAL 0x0000 153 #define RGEPHY_PCR_CLK125_DIS 0x0010 154 #define RGEPHY_PCR_JABBER_DIS 0x0001 155 156 /* RTL8211B(L)/RTL8211C(L) */ 157 #define RGEPHY_MII_SSR 0x11 /* PHY Specific status register */ 158 #define RGEPHY_SSR_S1000 0x8000 /* 1000Mbps */ 159 #define RGEPHY_SSR_S100 0x4000 /* 100Mbps */ 160 #define RGEPHY_SSR_S10 0x0000 /* 10Mbps */ 161 #define RGEPHY_SSR_SPD_MASK 0xc000 162 #define RGEPHY_SSR_FDX 0x2000 /* full duplex */ 163 #define RGEPHY_SSR_PAGE_RECEIVED 0x1000 /* new page received */ 164 #define RGEPHY_SSR_SPD_DPLX_RESOLVED 0x0800 /* speed/duplex resolved */ 165 #define RGEPHY_SSR_LINK 0x0400 /* link up */ 166 #define RGEPHY_SSR_MDI_XOVER 0x0040 /* MDI crossover */ 167 #define RGEPHY_SSR_ALDPS 0x0008 /* RTL8211C(L) only */ 168 #define RGEPHY_SSR_JABBER 0x0001 /* Jabber */ 169 170 /* RTL8211F */ 171 #define RGEPHY_F_MII_PCR1 0x18 /* PHY Specific control register 1 */ 172 #define RGEPHY_F_PCR1_MDI_MM 0x0200 /* MDI / MDIX Manual Mode */ 173 #define RGEPHY_F_PCR1_MDI_MODE 0x0100 /* MDI Mode (0=MDIX,1=MDI) */ 174 #define RGEPHY_F_PCR1_ALDPS_EN 0x0004 /* Link Down Power Saving Enable */ 175 176 /* RTL8211F */ 177 #define RGEPHY_F_MII_SSR 0x1A /* PHY Specific status register */ 178 #define RGEPHY_F_SSR_S1000 0x0020 /* 1000Mbps */ 179 #define RGEPHY_F_SSR_S100 0x0010 /* 100Mbps */ 180 #define RGEPHY_F_SSR_S10 0x0000 /* 10Mbps */ 181 #define RGEPHY_F_SSR_SPD_MASK 0x0030 182 #define RGEPHY_F_SSR_FDX 0x0008 /* full duplex */ 183 #define RGEPHY_F_SSR_LINK 0x0004 /* link up */ 184 #define RGEPHY_F_SSR_MDI 0x0002 /* MDI/MDIX */ 185 #define RGEPHY_F_SSR_JABBER 0x0001 /* Jabber */ 186 187 /* RTL8211F */ 188 #define RGEPHY_F_EPAGSR 0x1F /* Extension page select register */ 189 190 /* RTL8211F */ 191 #define RGEPHY_F_MMD_DEV_7 0x07 192 193 /* RTL8211F MMD device 7 */ 194 #define RGEPHY_F_MMD_EEEAR 0x3C /* EEE advertisement */ 195 #define EEEAR_1000T 0x0004 /* adv. 1000baseT EEE */ 196 #define EEEAR_100TX 0x0002 /* adv. 100baseTX EEE */ 197 198 /* RTL8211F MMD device 7 */ 199 #define RGEPHY_F_MMD_EEELPAR 0x3D /* EEE link partner abilities */ 200 #define EEELPAR_1000T 0x0004 /* link partner 1000baseT EEE capable */ 201 #define EEELPAR_100TX 0x0002 /* link partner 100baseTX EEE capable */ 202 203 /* RTL8153 */ 204 #define URE_GMEDIASTAT 0xe908 /* media status register */ 205 206 #endif /* _DEV_RGEPHY_MIIREG_H_ */ 207