1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/input/input.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10#include <dt-bindings/iio/qcom,spmi-vadc.h> 11 12/ { 13 thermal-zones { 14 pm8150-thermal { 15 polling-delay-passive = <100>; 16 17 thermal-sensors = <&pm8150_temp>; 18 19 trips { 20 trip0 { 21 temperature = <95000>; 22 hysteresis = <0>; 23 type = "passive"; 24 }; 25 26 trip1 { 27 temperature = <115000>; 28 hysteresis = <0>; 29 type = "hot"; 30 }; 31 32 trip2 { 33 temperature = <145000>; 34 hysteresis = <0>; 35 type = "critical"; 36 }; 37 }; 38 }; 39 }; 40}; 41 42&spmi_bus { 43 pm8150_0: pmic@0 { 44 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 45 reg = <0x0 SPMI_USID>; 46 #address-cells = <1>; 47 #size-cells = <0>; 48 49 pon: pon@800 { 50 compatible = "qcom,pm8998-pon"; 51 reg = <0x0800>; 52 mode-bootloader = <0x2>; 53 mode-recovery = <0x1>; 54 55 pon_pwrkey: pwrkey { 56 compatible = "qcom,pm8941-pwrkey"; 57 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 58 debounce = <15625>; 59 bias-pull-up; 60 linux,code = <KEY_POWER>; 61 62 status = "disabled"; 63 }; 64 65 pon_resin: resin { 66 compatible = "qcom,pm8941-resin"; 67 interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; 68 debounce = <15625>; 69 bias-pull-up; 70 71 status = "disabled"; 72 }; 73 }; 74 75 pm8150_temp: temp-alarm@2400 { 76 compatible = "qcom,spmi-temp-alarm"; 77 reg = <0x2400>; 78 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 79 io-channels = <&pm8150_adc ADC5_DIE_TEMP>; 80 io-channel-names = "thermal"; 81 #thermal-sensor-cells = <0>; 82 }; 83 84 pm8150_adc: adc@3100 { 85 compatible = "qcom,spmi-adc5"; 86 reg = <0x3100>; 87 #address-cells = <1>; 88 #size-cells = <0>; 89 #io-channel-cells = <1>; 90 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 91 92 channel@0 { 93 reg = <ADC5_REF_GND>; 94 qcom,pre-scaling = <1 1>; 95 label = "ref_gnd"; 96 }; 97 98 channel@1 { 99 reg = <ADC5_1P25VREF>; 100 qcom,pre-scaling = <1 1>; 101 label = "vref_1p25"; 102 }; 103 104 channel@6 { 105 reg = <ADC5_DIE_TEMP>; 106 qcom,pre-scaling = <1 1>; 107 label = "die_temp"; 108 }; 109 }; 110 111 pm8150_adc_tm: adc-tm@3500 { 112 compatible = "qcom,spmi-adc-tm5"; 113 reg = <0x3500>; 114 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 115 #thermal-sensor-cells = <1>; 116 #address-cells = <1>; 117 #size-cells = <0>; 118 status = "disabled"; 119 }; 120 121 rtc@6000 { 122 compatible = "qcom,pm8941-rtc"; 123 reg = <0x6000>, <0x6100>; 124 reg-names = "rtc", "alarm"; 125 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 126 }; 127 128 pm8150_gpios: gpio@c000 { 129 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio"; 130 reg = <0xc000>; 131 gpio-controller; 132 gpio-ranges = <&pm8150_gpios 0 0 10>; 133 #gpio-cells = <2>; 134 interrupt-controller; 135 #interrupt-cells = <2>; 136 }; 137 }; 138 139 pmic@1 { 140 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 141 reg = <0x1 SPMI_USID>; 142 #address-cells = <1>; 143 #size-cells = <0>; 144 }; 145}; 146