1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Support for CompuLab CM-T3530 4 */ 5/dts-v1/; 6 7#include "omap34xx.dtsi" 8#include "omap3-cm-t3x30.dtsi" 9 10/ { 11 model = "CompuLab CM-T3530"; 12 compatible = "compulab,omap3-cm-t3530", "ti,omap3430", "ti,omap34xx", "ti,omap3"; 13 14 /* Regulator to trigger the reset signal of the Wifi module */ 15 mmc2_sdio_reset: regulator-mmc2-sdio-reset { 16 compatible = "regulator-fixed"; 17 regulator-name = "regulator-mmc2-sdio-reset"; 18 regulator-min-microvolt = <3300000>; 19 regulator-max-microvolt = <3300000>; 20 gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>; 21 enable-active-high; 22 }; 23}; 24 25&omap3_pmx_core { 26 mmc2_pins: mmc2-pins { 27 pinctrl-single,pins = < 28 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ 29 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ 30 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ 31 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ 32 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ 33 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ 34 OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ 35 OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ 36 OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ 37 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ 38 >; 39 }; 40}; 41 42&mmc2 { 43 pinctrl-names = "default"; 44 pinctrl-0 = <&mmc2_pins>; 45 vmmc-supply = <&mmc2_sdio_reset>; 46 non-removable; 47 bus-width = <4>; 48 cap-power-off-card; 49}; 50 51&dss { 52 status = "okay"; 53 54 pinctrl-names = "default"; 55 pinctrl-0 = < 56 &dss_dpi_pins_common 57 &dss_dpi_pins_cm_t35x 58 >; 59}; 60 61