Searched hist:"1 b500373157c7c4da2765e3416834e86224373d6" (Results 1 – 3 of 3) sorted by relevance
| /linux/drivers/media/pci/bt8xx/ |
| H A D | Kconfig | diff 1b500373157c7c4da2765e3416834e86224373d6 Thu Jan 15 21:10:45 CET 2015 Ondrej Zary <linux@rainbow-software.org> [media] bttv: Convert to generic TEA575x interface
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
| H A D | bttvp.h | diff 1b500373157c7c4da2765e3416834e86224373d6 Thu Jan 15 21:10:45 CET 2015 Ondrej Zary <linux@rainbow-software.org> [media] bttv: Convert to generic TEA575x interface
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
| H A D | bttv-cards.c | diff 1b500373157c7c4da2765e3416834e86224373d6 Thu Jan 15 21:10:45 CET 2015 Ondrej Zary <linux@rainbow-software.org> [media] bttv: Convert to generic TEA575x interface
Remove tea575x-specific code from bttv and use the common driver instead.
Only set_frequency is implemented (signal/stereo detection or seek would
require more changes to bttv).
It works fine on Video Highway Xtreme (it actually makes the radio usable as
it currently cannot be tuned properly).
Miro/Pinnacle is untested but seems to be simple and should work.
However, I don't understand the Terratec Active Radio Upgrade code. The HW
seems to need IOR, IOW and CSEL signals that were taken from ISA bus on
older cards (IOR and IOW directly and CSEL from some address decoder) and
are emulated here using GPIOs. But the code manipulating these signals in
bttv seems to be broken - it never asserts the IOR signal. If anyone has
this HW, please test if I got that right.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|