| /freebsd/sys/contrib/device-tree/Bindings/power/ |
| H A D | wakeup-source.txt | 1 Specifying wakeup capability for devices
5 ----------------
6 Nodes that describe devices which have wakeup capability may contain a
7 "wakeup-source" boolean property.
9 If the device is marked as a wakeup-source, interrupt wake capability depends
10 on the device specific "interrupt-names" property. If no interrupts are labeled
14 However if a device has a dedicated interrupt as the wakeup source, then it
16 cases only that interrupt can be used as a wakeup interrupt.
18 While various legacy interrupt names exist, new devices should use "wakeup" as
22 ---------------------------------------------------------
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/usb/ |
| H A D | mediatek,mtk-xhci.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Chunfeng Yun <chunfeng.yun@mediatek.com>
14 - $ref: usb-xhci.yaml
19 case 2: supports dual-role mode, and the host is based on xHCI driver.
25 - enum:
26 - mediatek,mt2701-xhci
27 - mediatek,mt2712-xhci
[all …]
|
| H A D | mediatek,mtu3.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Chunfeng Yun <chunfeng.yun@mediatek.com>
14 - $ref: usb-drd.yaml
23 - enum:
24 - mediatek,mt2712-mtu3
25 - mediatek,mt8173-mtu3
26 - mediatek,mt8183-mtu3
27 - mediatek,mt8186-mtu3
[all …]
|
| H A D | mediatek,mtu3.txt | 4 - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3",
5 soc-model is the name of SoC, such as mt8173, mt2712 etc,
8 - "mediatek,mt8173-mtu3"
9 - reg : specifies physical base address and size of the registers
10 - reg-names: should be "mac" for device IP and "ippc" for IP port control
11 - interrupts : interrupt used by the device IP
12 - power-domains : a phandle to USB power domain node to control USB's
14 - vusb33-supply : regulator of USB avdd3.3v
15 - clocks : a list of phandle + clock-specifier pairs, one for each
16 entry in clock-names
[all …]
|
| H A D | mediatek,mtk-xhci.txt | 6 the second one supports dual-role mode, and the host is based on xHCI
11 ------------------------------------------------------------------------
14 - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci",
15 soc-model is the name of SoC, such as mt8173, mt2712 etc, when using
16 "mediatek,mtk-xhci" compatible string, you need SoC specific ones in
18 - "mediatek,mt8173-xhci"
19 - reg : specifies physical base address and size of the registers
20 - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control
21 - interrupts : interrupt used by the controller
22 - power-domains : a phandle to USB power domain node to control USB's
[all …]
|
| H A D | richtek,rt1719.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schema
[all...] |
| /freebsd/sys/contrib/device-tree/Bindings/rtc/ |
| H A D | isil,isl12057.txt | 8 ("wakeup-source") to handle the specific use-case found
9 on at least three in-tree users of the chip (NETGEAR ReadyNAS 102, 104
10 and 2120 ARM-based NAS); On those devices, the IRQ#2 pin of the chip
13 RTC alarm rings. In order to mark the device has a wakeup source and
20 - "compatible": must be "isil,isl12057"
21 - "reg": I2C bus address of the device
25 - "wakeup-source": mark the chip as a wakeup source, independently of
38 that the pinctrl-related properties below are given for completeness and
41 "interrupt-parent" and "interrupts" are usually sufficient):
60 pinctrl-0 = <&rtc_alarm_pin>;
[all …]
|
| H A D | rtc-opal.txt | 1 IBM OPAL real-time clock
2 ------------------------
5 - compatible: Should be "ibm,opal-rtc"
8 - wakeup-source: Decides if the wakeup is supported or not
9 (Legacy property supported: "has-tpo")
13 compatible = "ibm,opal-rtc";
14 wakeup-source;
|
| /freebsd/sys/contrib/device-tree/Bindings/soc/fsl/ |
| H A D | fsl,rcpm.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 The RCPM performs all device-level tasks associated with device run control
14 - Frank Li <Frank.Li@nxp.com>
19 - items:
20 - enum:
21 - fsl,p2041-rcpm
22 - fsl,p3041-rcpm
23 - fsl,p4080-rcpm
[all …]
|
| H A D | rcpm.txt | 2 -------------------------------------------
3 The RCPM performs all device-level tasks associated with device run control
7 - reg : Offset and length of the register set of the RCPM block.
8 - #fsl,rcpm-wakeup-cells : The number of IPPDEXPCR register cells in the
9 fsl,rcpm-wakeup property.
10 - compatible : Must contain a chip-specific RCPM block compatible string
11 and (if applicable) may contain a chassis-version RCPM compatible
12 string. Chip-specific strings are of the form "fsl,<chip>-rcpm",
14 * "fsl,p2041-rcpm"
15 * "fsl,p5020-rcpm"
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm/ti/omap/ |
| H A D | omap3-pandora-common.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
9 #include <dt-bindings/input/input.h>
14 cpu0-supply = <&vcc>;
29 #clock-cells = <0>;
30 compatible = "fixed-clock";
31 clock-frequency = <26000000>;
35 compatible = "connector-analog-tv";
40 remote-endpoint = <&venc_out>;
45 gpio-leds {
47 compatible = "gpio-leds";
[all …]
|
| H A D | omap3-ldp.dts | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
5 /dts-v1/;
7 #include <dt-bindings/input/input.h>
9 #include "omap-gpmc-smsc911x.dtsi"
13 compatible = "ti,omap3-ldp", "ti,omap3430", "ti,omap3";
22 cpu0-supply = <&vcc>;
27 compatible = "gpio-keys";
28 pinctrl-names = "default";
29 pinctrl-0 = <&gpio_key_pins>;
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/input/ |
| H A D | cypress,cyapa.txt | 4 - compatible: must be "cypress,cyapa".
5 - reg: I2C address of the chip.
6 - interrupts: interrupt to which the chip is connected (see interrupt
10 - wakeup-source: touchpad can be used as a wakeup source.
11 - pinctrl-names: should be "default" (see pinctrl binding [1]).
12 - pinctrl-0: a phandle pointing to the pin settings for the device (see
14 - vcc-supply: a phandle for the regulator supplying 3.3V power.
16 [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
17 [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
27 interrupt-parent = <&gpio>;
[all …]
|
| H A D | gpio-keys.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
4 $id: http://devicetree.org/schemas/input/gpio-keys.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Ro
[all...] |
| /freebsd/sys/contrib/device-tree/Bindings/net/ |
| H A D | marvell-bt-8xxx.txt | 2 ------
9 - compatible : should be one of the following:
10 * "marvell,sd8897-bt" (for SDIO)
11 * "marvell,sd8997-bt" (for SDIO)
16 - marvell,cal-data: Calibration data downloaded to the device during
20 - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
21 firmware will use the pin to wakeup host system (u16).
22 - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
25 - interrupt-names: Used only for USB based devices (See below)
26 - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the
[all …]
|
| /freebsd/sys/contrib/dev/iwlwifi/fw/api/ |
| H A D | d3.h | 1 /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
3 * Copyright (C) 2012-2014, 2018-2024 Intel Corporation
4 * Copyright (C) 2013-2014 Intel Mobile Communications GmbH
5 * Copyright (C) 2015-2017 Intel Deutschland GmbH
9 #include <iwl-tran
[all...] |
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | brcm,brcmstb-gpio.txt | 3 The controller's registers are organized as sets of eight 32-bit
9 - compatible:
10 Must be "brcm,brcmstb-gpio"
12 - reg:
16 - #gpio-cells:
19 bit[0]: polarity (0 for active-high, 1 for active-low)
21 - gpio-controller:
24 - brcm,gpio-bank-widths:
30 - interrupts:
33 - interrupts-extended:
[all …]
|
| /freebsd/share/man/man9/ |
| H A D | sleep.9 | 6 .\" Redistribution and use in source and binary forms, with or without
9 .\" 1. Redistributions of source code must retain the above copyright
39 .Nm wakeup ,
70 .Fn wakeup "const void *chan"
83 .Fn wakeup ,
87 handle event-based thread blocking.
110 .Fn wakeup ,
173 It allows the caller to specify relative or absolute wakeup time with higher resolution
200 change to the condition, or an associated wakeup.
218 to a lost wakeup.
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm/renesas/ |
| H A D | emev2-kzm9d.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the KZM9D board
7 /dts-v1/;
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/interrupt-controller/irq.h>
29 stdout-path = "serial1:115200n8";
33 compatible = "gpio-keys";
35 debounce-interval = <50>;
36 wakeup-source;
[all …]
|
| H A D | r8a7793-gose.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Gose board
5 * Copyright (C) 2014-2015 Renesas Electronics Corporation
9 * SSI-AK4643
36 /dts-v1/;
38 #include <dt-bindings/gpio/gpio.h>
39 #include <dt-bindings/input/input.h>
59 stdout-pat
[all...] |
| H A D | r8a7792-blanche.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the Blanche board
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
25 stdout-path = "serial0:115200n8";
33 d1_8v: regulator-1v8 {
34 compatible = "regulator-fixe
[all...] |
| /freebsd/sys/contrib/device-tree/src/arm64/mediatek/ |
| H A D | mt8183-kukui-jacuzzi-pico6.dts | 1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
6 /dts-v1/;
7 #include "mt8183-kukui-jacuzzi.dtsi"
8 #include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
12 chassis-type = "convertible";
13 compatible = "google,pico-sku2", "google,pico", "mediatek,mt8183";
15 bt_wakeup: bt-wakeup {
16 compatible = "gpio-keys";
17 pinctrl-names = "default";
18 pinctrl-0 = <&bt_pins_wakeup>;
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/i2c/ |
| H A D | i2c.txt | 8 -----------------------------
10 - #address-cells - should be <1>. Read more about addresses below.
11 - #size-cells - should be <0>.
12 - compatible - name of I2C bus controller
21 -----------------------------
26 - clock-frequency
29 - i2c-bus
31 devices and non-I2C devices, the 'i2c-bus' subnode can be used for
32 populating I2C devices. If the 'i2c-bus' subnode is present, only
34 '#address-cells' and '#size-cells' must be defined under this subnode
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/net/wireless/ |
| H A D | marvell-8xxx.txt | 2 ------
10 - compatible : should be one of the following:
21 - marvell,caldata* : A series of properties with marvell,caldata prefix,
23 initialization. This is an array of unsigned 8-bit values.
26 "marvell,caldata-txpwrlimit-2g" (length = 566).
27 "marvell,caldata-txpwrlimit-5g-sub0" (length = 502).
28 "marvell,caldata-txpwrlimit-5g-sub1" (length = 688).
29 "marvell,caldata-txpwrlimit-5g-sub2" (length = 750).
30 "marvell,caldata-txpwrlimit-5g-sub3" (length = 502).
31 - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm/microchip/ |
| H A D | at91-kizbox3-hs.dts | 1 // SPDX-License-Identifier: GPL-2.0
3 * at91-kizbox3-hs.dts - Device Tree file for Overkiz KIZBOX3-HS board
11 /dts-v1/;
12 #include "at91-kizbox3_common.dtsi"
15 model = "Overkiz KIZBOX3-HS";
16 compatible = "overkiz,kizbox3-hs", "atmel,sama5d2", "atmel,sama5";
18 led-controller-1 {
21 led-1 {
25 led-2 {
29 led-3 {
[all …]
|