Home
last modified time | relevance | path

Searched +full:vref +full:- +full:impedance (Results 1 – 13 of 13) sorted by relevance

/freebsd/sys/contrib/device-tree/Bindings/sound/
H A Dnuvoton,nau8325.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Seven Lee <WTLI@nuvoton.com>
13 - $ref: dai-common.yaml#
22 nuvoton,vref-impedance-ohms:
24 The vref impedance to be used in ohms. Middle of voltage enables
25 Tie-Off selection options. Due to the high impedance of the VREF
26 pin, it is important to use a low-leakage capacitor.
30 nuvoton,dac-vref-microvolt:
[all …]
H A Dnau8824.txt6 - compatible : Must be "nuvoton,nau8824"
8 - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
11 - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
13 - nuvoton,vref-impedance: VREF Impedance selection
14 0 - Open
15 1 - 25 kOhm
16 2 - 125 kOhm
17 3 - 2.5 kOhm
19 - nuvoton,micbias-voltage: Micbias voltage level.
20 0 - VDDA
[all …]
H A Dnau8825.txt6 - compatible : Must be "nuvoton,nau8825"
8 - reg : the I2C address of the device. This is either 0x1a (CSB=0) or 0x1b (CSB=1).
11 - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
12 - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
13 otherwise pin in high impedance state.
14 - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
15 - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
17 - nuvoton,vref-impedance: VREF Impedance selection
18 0 - Open
19 1 - 25 kOhm
[all …]
H A Dnau8821.txt6 - compatible : Must be "nuvoton,nau8821"
8 - reg : the I2C address of the device. This is either 0x1B (CSB=0) or 0x54 (CSB=1).
11 - nuvoton,jkdet-enable: Enable jack detection via JKDET pin.
12 - nuvoton,jkdet-pull-enable: Enable JKDET pin pull. If set - pin pull enabled,
13 otherwise pin in high impedance state.
14 - nuvoton,jkdet-pull-up: Pull-up JKDET pin. If set then JKDET pin is pull up, otherwise pull down.
15 - nuvoton,jkdet-polarity: JKDET pin polarity. 0 - active high, 1 - active low.
17 - nuvoton,vref-impedance: VREF Impedance selection
18 0 - Open
19 1 - 25 kOhm
[all …]
H A Dnuvoton,nau8824.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - John Hsu <KCHSU0@nuvoton.com>
13 - $ref: dai-common.yaml#
18 - nuvoton,nau8824
23 '#sound-dai-cells':
28 - description: The phandle of the master clock to the CODEC
30 clock-names:
32 - const: mclk
[all …]
H A Dnuvoton,nau8825.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - John Hsu <KCHSU0@nuvoton.com>
13 - $ref: dai-common.yaml#
18 - nuvoton,nau8825
26 nuvoton,jkdet-enable:
31 nuvoton,jkdet-pull-enable:
34 If set - pin pull enabled, otherwise pin in high impedance state.
37 nuvoton,jkdet-pull-up:
[all …]
H A Dnuvoton,nau8821.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Seven Lee <wtli@nuvoton.com>
13 - $ref: dai-common.yaml#
25 nuvoton,jkdet-enable:
29 nuvoton,jkdet-pull-enable:
30 description: Enable JKDET pin pull. If set - pin pull enabled,
31 otherwise pin in high impedance state.
34 nuvoton,jkdet-pull-up:
[all …]
/freebsd/sys/contrib/device-tree/Bindings/iio/adc/
H A Dmicrochip,mcp3911.yaml1 # SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Marcu
[all...]
H A Dst,stm32-adc.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/iio/adc/st,stm32-adc.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 STM32 ADC is a successive approximation analog-to-digital converter.
13 stored in a left-aligned or right-aligned 32-bit data register.
17 voltage goes beyond the user-defined, higher or lower thresholds.
22 - Fabrice Gasnier <fabrice.gasnier@foss.st.com>
27 - st,stm32f4-adc-core
28 - st,stm32h7-adc-core
[all …]
/freebsd/sys/contrib/device-tree/src/arm/st/
H A Dstm32mp135f-dhcor-dhsbc.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
6 * DHCR-STM32MP135F-C100-R051-EE-F0409-SPI4-RTC-WBT-I-01LG
7 * DHCOR PCB number: 718-100 or newer
8 * DHSBC PCB number: 719-100 or newer
11 /dts-v1/;
13 #include <dt-bindings/regulator/st,stm32mp13-regulator.h>
16 #include "stm32mp13xx-dhcor-som.dtsi"
20 compatible = "dh,stm32mp135f-dhcor-dhsbc",
21 "dh,stm32mp135f-dhcor-som",
32 stdout-path = "serial0:115200n8";
[all …]
H A Dstm32mp135f-dk.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (C) STMicroelectronics 2021 - All Rights Reserved
7 /dts-v1/;
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/regulator/st,stm32mp13-regulator.h>
15 #include "stm32mp13-pinctrl.dtsi"
18 model = "STMicroelectronics STM32MP135F-DK Discovery Board";
19 compatible = "st,stm32mp135f-dk", "st,stm32mp135";
[all …]
H A Dstm32mp15xx-dkx.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
3 * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
7 #include <dt-bindings/gpio/gpio.h>
8 #include <dt-bindings/mfd/st,stpmic1.h>
22 reserved-memory {
23 #address-cell
[all...]
/freebsd/sys/contrib/device-tree/src/arm64/nvidia/
H A Dtegra210-smaug.dts1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
4 #include <dt-bindings/input/input.h>
5 #include <dt-bindings/mfd/max77620.h>
6 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
12 compatible = "google,smaug-rev8", "google,smaug-rev7",
13 "google,smaug-rev6", "google,smaug-rev5",
14 "google,smaug-rev4", "google,smaug-rev3",
15 "google,smaug-rev2", "google,smaug-rev1",
25 stdout-path = "serial0:115200n8";
[all …]