| /freebsd/sys/contrib/device-tree/Bindings/media/i2c/ |
| H A D | adv7604.txt | 1 * Analog Devices ADV7604/11/12 video decoder with HDMI receiver
3 The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
12 - compatible: Must contain one of the following
13 - "adi,adv7611" for the ADV7611
14 - "adi,adv7612" for the ADV7612
16 - reg: I2C slave addresses
17 The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
22 - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
24 level that enables hot-plug detection.
27 port, in accordance with the video interface bindings defined in
[all …]
|
| H A D | mt9m001.txt | 1 MT9M001: 1/2-Inch Megapixel Digital Image Sensor
3 The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital
8 - compatible: shall be "onnn,mt9m001".
9 - clocks: reference to the master clock into sensor
13 - reset-gpios: GPIO handle which is connected to the reset pin of the chip.
15 - standby-gpios: GPIO handle which is connected to the standby pin of the chip.
19 sub-node for its digital output video port, in accordance with the video
21 Documentation/devicetree/bindings/media/video-interfaces.txt
26 camera-sensor@5d {
29 reset-gpios = <&gpio0 0 GPIO_ACTIVE_LOW>;
[all …]
|
| H A D | ov5645.txt | 1 * Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
3 The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
8 - compatible: Value should be "ovti,ov5645".
9 - clocks: Reference to the xclk clock.
10 - clock-names: Should be "xclk".
11 - clock-frequency: Frequency of the xclk clock.
12 - enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
14 - reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
16 - vdddo-supply: Chip digital IO regulator.
17 - vdda-supply: Chip analog regulator.
[all …]
|
| H A D | ov9650.txt | 4 - compatible: shall be one of
7 - clocks: reference to the xvclk input clock.
10 - reset-gpios: reference to the GPIO connected to the resetb pin, if any.
12 - powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
16 subnode for its digital output video port, in accordance with the video
18 video-interfaces.txt.
26 reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>;
27 powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>;
32 remote-endpoint = <&vcap1_in0>;
|
| H A D | techwell,tw9900.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Techwell TW9900 NTSC/PAL video decoder
10 - Mehdi Djait <mehdi.djait@bootlin.com>
13 The tw9900 is a multi-standard video decoder, supporting NTSC, PAL standards
14 with auto-detection features.
23 vdd-supply:
26 reset-gpios:
27 description: GPIO descriptor for the RESET input pin
[all …]
|
| H A D | ov772x.txt | 8 - compatible: shall be one of
11 - clocks: reference to the xclk input clock.
14 - reset-gpios: reference to the GPIO connected to the RSTB pin which is
16 - powerdown-gpios: reference to the GPIO connected to the PWDN pin which is
20 subnode for its digital output video port, in accordance with the video
22 video-interfaces.txt.
30 reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
31 powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
36 remote-endpoint = <&vcap1_in0>;
|
| H A D | aptina,mt9v111.txt | 2 ----------------------------
4 The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
8 of image resolution and formats controllable through a simple two-wires
12 --------------------
14 - compatible: shall be "aptina,mt9v111".
15 - clocks: reference to the system clock input provider.
18 --------------------
20 - enable-gpios: output enable signal, pin name "OE#". Active low.
21 - standby-gpios: low power state control signal, pin name "STANDBY".
23 - reset-gpios: chip reset signal, pin name "RESET#". Active low.
[all …]
|
| H A D | galaxycore,gc0308.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sebastian Reichel <sre@kernel.org>
18 - $ref: /schemas/media/video-interface-devices.yaml#
23 - const: galaxycore,gc0308
24 - items:
25 - const: galaxycore,gc0309
26 - const: galaxycore,gc0308
35 reset-gpios:
[all …]
|
| H A D | ov5640.txt | 1 * Omnivision OV5640 MIPI CSI-2 / parallel sensor
4 - compatible: should be "ovti,ov5640"
5 - clocks: reference to the xclk input clock.
6 - clock-names: should be "xclk".
7 - DOVDD-supply: Digital I/O voltage supply, 1.8 volts
8 - AVDD-supply: Analog voltage supply, 2.8 volts
9 - DVDD-supply: Digital core voltage supply, 1.5 volts
12 - reset-gpios: reference to the GPIO connected to the reset pin, if any.
14 - powerdown-gpios: reference to the GPIO connected to the powerdown pin,
16 - rotation: as defined in
[all …]
|
| H A D | tvp5150.txt | 1 * Texas Instruments TVP5150 and TVP5151 video decoders
3 The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
4 (and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
5 with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
9 - compatible: Value must be "ti,tvp5150".
10 - reg: I2C slave address.
14 - pdn-gpio
[all...] |
| H A D | ov7670.txt | 8 - compatible: should be "ovti,ov7670"
9 - clocks: reference to the xclk input clock.
10 - clock-names: should be "xclk".
13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
17 - reset-gpios: reference to the GPIO connected to the resetb pin, if any.
19 - powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
21 - ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output
25 sub-node for its digital output video port, in accordance with the video
27 Documentation/devicetree/bindings/media/video-interfaces.txt.
[all …]
|
| H A D | ov2685.txt | 1 * Omnivision OV2685 MIPI CSI-2 sensor
4 - compatible: shall be "ovti,ov2685"
5 - clocks: reference to the xvclk input clock
6 - clock-names: shall be "xvclk"
7 - avdd-supply: Analog voltage supply, 2.8 volts
8 - dovdd-supply: Digital I/O voltage supply, 1.8 volts
9 - dvdd-supply: Digital core voltage supply, 1.8 volts
10 - reset-gpios: Low active reset gpio
13 'endpoint' subnode for its digital output video port,
14 in accordance with the video interface bindings defined in
[all …]
|
| H A D | imx290.txt | 1 * Sony IMX290 1/2.8-Inch CMOS Image Sensor
3 The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
4 Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
6 Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
10 - compatible: Should be "sony,imx290"
11 - reg: I2C bus address of the device
12 - clocks: Reference to the xclk clock.
13 - clock-names: Should be "xclk".
14 - clock-frequency: Frequency of the xclk clock in Hz.
15 - vdddo-supply: Sensor digital IO regulator.
[all …]
|
| H A D | ov5695.txt | 1 * Omnivision OV5695 MIPI CSI-2 sensor
4 - compatible: shall be "ovti,ov5695"
5 - clocks: reference to the xvclk input clock
6 - clock-names: shall be "xvclk"
7 - avdd-supply: Analog voltage supply, 2.8 volts
8 - dovdd-supply: Digital I/O voltage supply, 1.8 volts
9 - dvdd-supply: Digital core voltage supply, 1.2 volts
10 - reset-gpios: Low active reset gpio
13 'endpoint' subnode for its digital output video port,
14 in accordance with the video interface bindings defined in
[all …]
|
| H A D | nokia,smia.txt | 8 Documentation/devicetree/bindings/media/video-interfaces.txt .
11 endpoint nodes, in accordance with video interface bindings defined in
12 Documentation/devicetree/bindings/media/video-interfaces.txt .
15 --------------------
17 - compatible: "nokia,smia"
18 - reg: I2C address (0x10, or an alternative address)
19 - vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor
21 - clocks: External clock to the sensor
22 - clock-frequency: Frequency of the external clock to the sensor
23 - link-frequencies: List of allowed data link frequencies. An array of
[all …]
|
| H A D | mipi-ccs.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (C) 2014--2020 Intel Corporation
4 ---
5 $id: http://devicetree.org/schemas/media/i2c/mipi-ccs.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Sakari Ailus <sakari.ailus@linux.intel.com>
17 <URL:https://www.mipi.org/specifications/camera-command-set>.
24 Documentation/devicetree/bindings/media/video-interfaces.txt .
29 - items:
30 - const: mipi-ccs-1.1
[all …]
|
| H A D | ov2680.txt | 1 * Omnivision OV2680 MIPI CSI-2 sensor
4 - compatible: should be "ovti,ov2680".
5 - clocks: reference to the xvclk input clock.
6 - clock-names: should be "xvclk".
7 - DOVDD-supply: Digital I/O voltage supply.
8 - DVDD-supply: Digital core voltage supply.
9 - AVDD-supply: Analog voltage supply.
12 - reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
16 video port, and this port must have a single endpoint in accordance with
17 the video interface bindings defined in
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/display/bridge/ |
| H A D | ps8640.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: MIPI DSI to eDP Video Format Converter
10 - Nicolas Boichat <drinkcat@chromium.org>
13 The PS8640 is a low power MIPI-to-eDP video format converter supporting
28 powerdown-gpios:
32 reset-gpios:
34 description: GPIO connected to active low reset.
36 vdd12-supply:
[all …]
|
| H A D | toshiba,tc358775.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Vinay Simha BN <simhavcs@gmail.com>
15 MIPI DSI-RX Data 4-lane, CLK 1-lane with data rates up to 800 Mbps/lane.
16 Video frame size:
17 Up to 1600x1200 24-bit/pixel resolution for single-link LVDS display panel
19 Up to WUXGA (1920x1200 24-bit pixels) resolution for dual-link LVDS display
25 - toshiba,tc358765
26 - toshiba,tc358775
[all …]
|
| H A D | ps8622.txt | 1 ps8622-bridge bindings
4 - compatible: "parade,ps8622" or "parade,ps8625"
5 - reg: first i2c address of the bridge
6 - sleep-gpios: OF device-tree gpio specification for PD_ pin.
7 - reset-gpios: OF device-tree gpio specification for RST_ pin.
10 - lane-count: number of DP lanes to use
11 - use-external-pwm: backlight will be controlled by an external PWM
12 - video interfaces: Device node can contain video interface port
15 [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
18 lvds-bridge@48 {
[all …]
|
| H A D | sii9234.txt | 4 - compatible : "sil,sii9234".
5 - reg : I2C address for TPI interface, use 0x39
6 - avcc33-supply : MHL/USB Switch Supply Voltage (3.3V)
7 - iovcc18-supply : I/O Supply Voltage (1.8V)
8 - avcc12-supply : TMDS Analog Supply Voltage (1.2V)
9 - cvcc12-supply : Digital Core Supply Voltage (1.2V)
10 - interrupts: interrupt specifier of INT pin
11 - reset-gpios: gpio specifier of RESET pin (active low)
12 - video interfaces: Device node can contain two video interface port
14 - port@0 - MHL to HDMI
[all …]
|
| H A D | toshiba,tc358767.txt | 4 - compatible: "toshiba,tc358767"
5 - reg: i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins
6 - clock-names: should be "ref"
7 - clocks: OF device-tree clock specification for refclk input. The reference
11 - shutdown-gpios: OF device-tree gpio specification for SD pin
13 - reset-gpios: OF device-tree gpio specification for RSTX pin
14 (active low system reset)
15 - toshiba,hpd-pin: TC358767 GPIO pin number to which HPD is connected to (0 or 1)
16 - ports: the ports node can contain video interface port nodes to connect
18 - port@0: DSI input port
[all …]
|
| H A D | nxp,ptn3460.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sean Paul <seanpaul@chromium.org>
20 edid-emulation:
34 powerdown-gpios:
38 reset-gpios:
49 Video port for LVDS output
54 Video port for eDP input
57 - port@0
[all …]
|
| H A D | parade,ps8622.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
15 - parade,ps8622
16 - parade,ps8625
21 lane-count:
26 use-external-pwm:
30 reset-gpios:
34 sleep-gpios:
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/display/panel/ |
| H A D | novatek,nt36672a.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Sumit Semwal <sumit.semwal@linaro.org>
16 resolution of 1080x2246. It is a video mode DSI panel.
19 - $ref: panel-common.yaml#
24 - enum:
25 - tianma,fhd-video
26 - const: novatek,nt36672a
35 reset-gpios:
[all …]
|