Home
last modified time | relevance | path

Searched +full:usb2 +full:- +full:only (Results 1 – 25 of 263) sorted by relevance

1234567891011

/freebsd/sys/contrib/device-tree/Bindings/usb/
H A Damlogic,meson-g12a-usb-ctrl.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/usb/amlogic,meson-g12a-usb-ctrl.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Neil Armstrong <neil.armstrong@linaro.org>
14 The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
15 in host-only mode, and a DWC2 IP Core configured for USB2 peripheral mode
16 only.
18 A glue connects the DWC3 core to USB2 PHYs and optionally to an USB3 PHY.
20 One of the USB2 PHYs can be re-routed in peripheral mode to a DWC2 USB IP.
[all …]
H A Dfsl,usb2.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/usb/fsl,usb2.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Frank Li <Frank.Li@nxp.com>
21 - enum:
22 - fsl-usb2-mph
23 - fsl-usb2-dr
24 - items:
25 - enum:
[all …]
H A Dfsl-usb.txt9 - compatible : Should be "fsl-usb2-mph" for multi port host USB
10 controllers, or "fsl-usb2-dr" for dual role USB controllers
11 or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121.
13 also be mentioned (for eg. fsl-usb2-dr-v2.2 for bsc9132).
14 - phy_type : For multi port host USB controllers, should be one of
17 - reg : Offset and length of the register set for the device
18 - port0 : boolean; if defined, indicates port0 is connected for
19 fsl-usb2-mph compatible controllers. Either this property or
20 "port1" (or both) must be defined for "fsl-usb2-mph" compatible
22 - port1 : boolean; if defined, indicates port1 is connected for
[all …]
H A Ddwc3.txt3 DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties
7 - compatible: must be "snps,dwc3"
8 - reg : Address and length of the register set for the device
9 - interrupts: Interrupts used by the dwc3 controller.
10 - clock-names: list of clock names. Ideally should be "ref",
12 - clocks: list of phandle and clock specifier pairs corresponding to
13 entries in the clock-names property.
16 clocks are optional if the parent node (i.e. glue-layer) is compatible to
18 "cavium,octeon-7130-usb-uctl"
20 "samsung,exynos5250-dwusb3"
[all …]
H A Dsnps,dwc3.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Felipe Balbi <balbi@kernel.org>
14 be presented as a standalone DT node with an optional vendor-specific
18 - $ref: usb-drd.yaml#
19 - if:
25 - dr_mode
29 $ref: usb-xhci.yaml#
35 - const: snps,dwc3
[all …]
H A Dmediatek,mtk-xhci.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
5 $id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Chunfeng Yun <chunfeng.yun@mediatek.com>
14 - $ref: usb-xhci.yaml
18 case 1: only supports xHCI driver;
19 case 2: supports dual-role mode, and the host is based on xHCI driver.
25 - enum:
26 - mediatek,mt2701-xhci
[all …]
H A Dxlnx,usb2.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
[all...]
H A Dnvidia,tegra194-xusb.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/usb/nvidia,tegra194-xusb.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Thierry Reding <thierry.reding@gmail.com>
11 - Jon Hunter <jonathanh@nvidia.com>
13 description: The Tegra xHCI controller supports both USB2 and USB3 interfaces
18 const: nvidia,tegra194-xusb
22 - description: base and length of the xHCI host registers
23 - description: base and length of the XUSB FPCI registers
[all …]
/freebsd/sys/contrib/device-tree/Bindings/phy/
H A Dsamsung,usb2-phy.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/phy/samsung,usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Krzysztof Kozlowski <krzk@kernel.org>
11 - Marek Szyprowski <m.szyprowski@samsung.com>
12 - Sylwester Nawrocki <s.nawrocki@samsung.com>
18 0 - USB device ("device"),
19 1 - USB host ("host"),
20 2 - HSIC0 ("hsic0"),
[all …]
H A Dsocionext,uniphier-usb2-phy.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/socionext,uniphier-usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Socionext UniPhier USB2 PHY
11 USB2 controller implemented on Socionext UniPhier SoCs.
12 Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3
13 controller doesn't include its own High-Speed PHY. This needs to specify
14 USB2 PHY instead of USB3 HS-PHY.
17 - Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[all …]
H A Dnvidia,tegra194-xusb-padctl.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/phy/nvidia,tegra194-xusb-padctl.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Thierry Reding <thierry.reding@gmail.com>
11 - Jon Hunter <jonathanh@nvidia.com>
21 Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
22 super-speed USB. Other lanes are for various types of low-speed, full-speed
23 or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
24 contains a software-configurable mux that sits between the I/O controller
[all …]
H A Dphy-mvebu-utmi.txt2 --------------------
4 USB2 UTMI+ PHY controllers can be found on the following Marvell MVEBU SoCs:
7 On Armada 3700, there are two USB controllers, one is compatible with the USB2
8 and USB3 specifications and supports OTG. The other one is USB2 compliant and
9 only supports host mode. Both of these controllers come with a slightly
14 - compatible: Should be one of:
15 * "marvell,a3700-utmi-host-phy" for the PHY connected to
16 the USB2 host-only controller.
17 * "marvell,a3700-utmi-otg-phy" for the PHY connected to
18 the USB3 and USB2 OTG capable controller.
[all …]
H A Dnvidia,tegra124-xusb-padctl.txt11 Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or
12 super-speed USB. Other lanes are for various types of low-speed, full-speed
13 or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller
14 contains a software-configurable mux that sits between the I/O controller
17 In addition to per-lane configuration, USB 3.0 ports may require additional
18 settings on a per-board basis.
20 Pads will be represented as children of the top-level XUSB pad controller
23 PHY bindings, as described by the phy-bindings.txt file in this directory.
34 --------------------
35 - compatible: Must be:
[all …]
H A Drenesas,usb2-phy.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/renesas,usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Renesas R-Car generation 3 USB 2.0 PHY
10 - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
15 - items:
16 - enum:
17 - renesas,usb2-phy-r8a77470 # RZ/G1C
18 - renesas,usb2-phy-r9a08g045 # RZ/G3S
[all …]
H A Dti,omap-usb2.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/ti,omap-usb2.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: OMAP USB2 PHY
10 - Kishon Vijay Abraham I <kishon@ti.com>
11 - Roger Quadros <rogerq@kernel.org>
16 - items:
17 - enum:
18 - ti,dra7x-usb2
[all …]
H A Damlogic,meson8b-usb2-phy.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/amlogic,meson8b-usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Amlogic Meson8, Meson8b, Meson8m2 and GXBB USB2 PHY
10 - Martin Blumenstingl <martin.blumenstingl@googlemail.com>
15 - items:
16 - enum:
17 - amlogic,meson8-usb2-phy
18 - amlogic,meson8b-usb2-phy
[all …]
H A Dphy-lantiq-rcu-usb2.txt9 -------------------------------------------------------------------------------
11 - compatible : Should be one of
12 "lantiq,ase-usb2-phy"
13 "lantiq,danube-usb2-phy"
14 "lantiq,xrx100-usb2-phy"
15 "lantiq,xrx200-usb2-phy"
16 "lantiq,xrx300-usb2-phy"
17 - reg : Defines the following sets of registers in the parent
19 - Offset of the USB PHY configuration register
20 - Offset of the USB Analog configuration
[all …]
H A Dbcm-ns-usb2-phy.txt4 - compatible: brcm,ns-usb2-phy
5 - reg: iomem address range of DMU (Device Management Unit)
6 - reg-names: "dmu", the only needed & supported reg right now
7 - clocks: USB PHY reference clock
8 - clock-names: "phy-ref-clk", the only needed & supported clock right now
14 usb2-phy {
15 compatible = "brcm,ns-usb2-phy";
17 reg-names = "dmu";
18 #phy-cells = <0>;
20 clock-names = "phy-ref-clk";
H A Dnuvoton,ma35d1-usb2-phy.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/nuvoton,ma35d1-usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Nuvoton MA35D1 USB2 phy
10 - Hui-Ping Chen <hpchen0nvt@gmail.com>
15 - nuvoton,ma35d1-usb2-phy
17 "#phy-cells":
29 - compatible
30 - "#phy-cells"
[all …]
H A Damlogic,meson-gxl-usb2-phy.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/phy/amlogic,meson-gxl-usb2-phy.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Amlogic Meson GXL USB2 PHY
10 - Neil Armstrong <neil.armstrong@linaro.org>
14 const: amlogic,meson-gxl-usb2-phy
22 clock-names:
24 - const: phy
29 reset-names:
[all …]
/freebsd/sys/contrib/device-tree/Bindings/clock/
H A Drenesas,rcar-usb2-clock-sel.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/clock/renesas,rcar-usb2-clock-sel.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Renesas R-Car USB 2.0 clock selector
10 - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
13 If you connect an external clock to the USB_EXTAL pin only, you should set
14 the clock rate to "usb_extal" node only.
19 Case 1: An external clock connects to R-Car SoC
20 +----------+ +--- R-Car ---------------------+
[all …]
H A Drenesas,rcar-usb2-clock-sel.txt1 * Renesas R-Car USB 2.0 clock selector
3 This file provides information on what the device node for the R-Car USB 2.0
6 If you connect an external clock to the USB_EXTAL pin only, you should set
7 the clock rate to "usb_extal" node only.
12 Case 1: An external clock connects to R-Car SoC
13 +----------+ +--- R-Car ---------------------+
14 |External |---|USB_EXTAL ---> all usb channels|
16 +----------+ +-------------------------------+
19 Case 2: An oscillator connects to R-Car SoC
20 +----------+ +--- R-Car ---------------------+
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/nvidia/
H A Dtegra234-p3740-0002.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 #include <dt-bindings/sound/rt5640.h>
6 compatible = "nvidia,p3740-0002";
15 dai-format = "i2s";
16 remote-endpoint = <&rt5640_ep>;
26 bitclock-master;
27 frame-master;
36 rt5640: audio-code
[all...]
H A Dtegra234-p3768-0000.dtsi1 // SPDX-License-Identifier: GPL-2.0
4 compatible = "nvidia,p3768-0000";
11 stdout-path = "serial0:115200n8";
23 vcc-supply = <&vdd_1v8_sys>;
24 address-width = <8>;
27 read-only;
32 current-spee
[all...]
H A Dtegra234-p3768-0000+p3767.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 #include <dt-bindings/input/linux-event-codes.h>
4 #include <dt-bindings/input/gpio-keys.h>
6 #include "tegra234-p3767.dtsi"
17 stdout-path = "serial0:115200n8";
22 compatible = "nvidia,tegra194-hsuart";
23 reset-names = "serial";
28 compatible = "nvidia,tegra194-hsuart";
29 reset-names = "serial";
41 vcc-supply = <&vdd_1v8_sys>;
[all …]

1234567891011