| /linux/Documentation/leds/ |
| H A D | leds-lm3556.rst | 16 There are 3 functions in LM3556, Flash, Torch and Indicator.
47 Torch Mode
50 In Torch Mode, the current source(LED) is programmed via the CURRENT CONTROL
51 REGISTER(0x09).Torch Mode is activated by the ENABLE REGISTER(0x0A) or by the
52 hardware TORCH input.
54 LM3556 torch can be controlled through /sys/class/leds/torch/brightness file.
55 * if TORCH pin is enabled, below example control brightness only,
56 and ON / OFF will be controlled by TORCH pin.
58 Torch Example:
62 #echo 0 > /sys/class/leds/torch/brightness
[all …]
|
| H A D | leds-class-flash.rst | 5 Some LED devices provide two modes - torch and flash. In the LED subsystem
7 and LED Flash class respectively. The torch mode related features are enabled
68 constraints for the LED in TORCH mode
|
| /linux/drivers/leds/flash/ |
| H A D | Kconfig | 40 of flash, torch and indicator classes.
50 and torch mode.
62 Independent current sources supply for each flash LED support torch
71 Support 2 channels and torch/strobe mode.
102 RT4505 includes torch and flash functions with programmable current.
107 tristate "LED support for Richtek RT8515 flash/torch LED"
112 and torch LEDs found on some mobile phones.
131 SY7802 includes torch and flash functions with programmable current.
|
| H A D | leds-rt8515.c | 3 * LED driver for Richtek RT8515 flash/torch white LEDs
15 * RTS (resistance torch setting?) is 39 kOhm
40 /* The maximum intensity is 1-16 for flash and 1-100 for torch */
89 /* This is setting the torch light level */
105 /* Max torch brightness requested */ in rt8515_led_brightness_set()
136 /* After this the torch LED will be disabled */ in rt8515_led_flash_strobe_set()
301 /* ENT - Enable Torch line */ in rt8515_probe()
305 "cannot get ENT (enable torch) GPIO\n"); in rt8515_probe()
|
| H A D | leds-lm3601x.c | 2 // Flash and torch driver for Texas Instruments LM3601X LED
80 * @torch_current_max: maximum current for the torch
83 * @led_mode: The mode to enable either IR or Torch
352 "torch" : "infrared"; in lm3601x_register_leds()
392 "Max torch current set too high (%d vs %d)\n", in lm3601x_parse_node()
|
| H A D | leds-max77693.c | 42 TORCH, enumerator
83 /* maximum torch current values for FLED outputs */
162 * Enable hw triggering also for torch mode, as some in max77693_set_mode_reg()
163 * camera sensors use torch led to fathom ambient light in max77693_set_mode_reg()
212 * strobing on each subsequent torch mode setting. in max77693_add_mode()
273 max77693_distribute_currents(led, fled_id, TORCH, micro_amp, in max77693_set_torch_current()
399 * Initialize only flash current. Torch current doesn't in max77693_setup()
475 "Failed to clear torch mode (%d)\n", in max77693_led_brightness_set()
483 "Failed to set torch current (%d)\n", in max77693_led_brightness_set()
491 "Failed to set torch mode (%d)\n", in max77693_led_brightness_set()
|
| H A D | leds-sy7802.c | 123 dev_warn(chip->dev, "Cannot set torch brightness whilst strobe is enabled\n"); in sy7802_torch_brightness_set()
141 /* Disable torch to apply brightness */ in sy7802_torch_brightness_set()
207 dev_warn(chip->dev, "Cannot set strobe brightness whilst torch is enabled\n"); in sy7802_strobe_set()
|
| /linux/Documentation/devicetree/bindings/leds/ |
| H A D | richtek,rt8515.yaml | 14 supports driving a white LED in flash or torch mode. The maximum
28 description: A connection to the 'ENT' (enable torch) pin.
43 resistors limits the maximum torch current. This must be set
44 for the property torch-max-microamp to work, the RTS resistor
46 torch LED.
70 description: The maximum current for torch mode
|
| H A D | ams,as3645a.txt | 5 used in torch mode as well.
31 led-max-microamp: Maximum torch (assist) current in microamperes. The
|
| H A D | common.yaml | 121 # LED indicates camera torch state
122 - torch
160 mandatory for the LEDs in the non-flash modes (e.g. torch or indicator).
|
| H A D | mediatek,mt6370-flashlight.yaml | 14 Add MT6370 flash LED driver include 2-channel flash LED support Torch/Strobe Mode.
|
| H A D | leds-rt4505.yaml | 14 torch and flash mode, respectively.
|
| /linux/drivers/leds/trigger/ |
| H A D | ledtrig-camera.c | 3 * Camera Flash and Torch On/Off Trigger
39 led_trigger_register_simple("torch", &ledtrig_torch); in ledtrig_camera_init()
51 MODULE_DESCRIPTION("LED Trigger for Camera Flash/Torch Control");
|
| H A D | Kconfig | 110 tristate "LED Camera Flash/Torch Trigger"
112 This allows LEDs to be controlled as a camera flash/torch device.
113 This enables direct flash/torch on/off by the driver, kernel space.
|
| /linux/drivers/media/v4l2-core/ |
| H A D | v4l2-flash-led-class.c | 50 * Indicator LEDs, unlike torch LEDs, are turned on/off basing on in __intensity_to_led_brightness()
65 * Indicator LEDs, unlike torch LEDs, are turned on/off basing on in __led_brightness_to_intensity()
68 * indicator LED as it may equal 0. For torch LEDs this function in __led_brightness_to_intensity()
71 * V4L2_FLASH_LED_MODE_NONE the cached torch intensity value is used. in __led_brightness_to_intensity()
131 * Update torch brightness only if in TORCH_MODE. In other modes in v4l2_flash_update_led_brightness()
132 * torch led is turned off, which would spuriously inform the in v4l2_flash_update_led_brightness()
240 /* Turn the torch LED off */ in v4l2_flash_s_ctrl()
272 * affect torch mode. Therefore, if not in the flash mode, in v4l2_flash_s_ctrl()
548 * torch mode. Synchronize strobe source setting only if not in torch in __sync_device_with_v4l2_controls()
549 * mode. For torch mode case it will get synchronized upon switching in __sync_device_with_v4l2_controls()
|
| /linux/include/media/i2c/ |
| H A D | lm3646.h | 30 /* TOTAL TORCH Brightness Max
50 /* LED1 TORCH Brightness
74 * @led1_torch_brt: led1 torch mode brightness, uA
|
| H A D | lm3560.h | 44 /* TORCH BRT
74 * @max_torch_brt: torch mode led brightness
|
| /linux/drivers/leds/ |
| H A D | leds-tps6105x.c | 44 /* This instance is not set for torch mode so bail out */ in tps6105x_led_probe()
47 "chip not in torch mode, exit probe"); in tps6105x_led_probe()
63 init_data.default_label = ":torch"; in tps6105x_led_probe()
|
| H A D | leds-lm3642.c | 165 /* torch */
167 /* torch pin config for lm3642 */
348 /* torch */ in lm3642_probe()
349 chip->cdev_torch.name = "torch"; in lm3642_probe()
352 chip->cdev_torch.default_trigger = "torch"; in lm3642_probe()
356 dev_err(chip->dev, "failed to register torch\n"); in lm3642_probe()
|
| H A D | leds-lm355x.c | 235 "torch brt is set - ext. torch pin mode\n"); in lm355x_control()
306 /* torch */
459 /* torch */ in lm355x_probe()
460 chip->cdev_torch.name = "torch"; in lm355x_probe()
463 chip->cdev_torch.default_trigger = "torch"; in lm355x_probe()
|
| /linux/Documentation/userspace-api/media/v4l/ |
| H A D | ext-ctrls-flash.rst | 45 LED flash as torch
48 LED flash may be used as torch in conjunction with another use case
77 - Torch mode.
126 Intensity of the flash LED in torch mode
|
| /linux/drivers/media/i2c/ |
| H A D | lm3646.c | 237 /* max torch current */ in lm3646_init_controls()
323 * LED1 torch current setting in lm3646_init_device()
324 * LED2 torch current = Total(Max) torch current - LED1 torch current in lm3646_init_device()
|
| /linux/include/linux/platform_data/ |
| H A D | leds-lm355x.h | 48 * lm3554-tx1/torch/gpio1
49 * lm3556-torch
|
| /linux/drivers/video/backlight/ |
| H A D | lm3639_bl.c | 218 /* torch */
271 /* torch off before flash control */ in lm3639_flash_brightness_set()
372 /* torch */ in lm3639_probe()
379 dev_err(&client->dev, "fail : torch register\n"); in lm3639_probe()
|
| /linux/drivers/staging/greybus/ |
| H A D | light.c | 140 /* If the channel is flash we need to get the attached torch channel */ in __gb_lights_flash_brightness_set()
731 /* we can only attach torch to a flash channel */ in __gb_lights_channel_torch_attach()
735 /* Move torch brightness to the destination */ in __gb_lights_channel_torch_attach()
779 * If light have torch mode channel, this channel will be the led in __gb_lights_flash_led_register()
827 * Intensity constraints for flash related modes: flash, torch, in gb_lights_channel_flash_config()
893 * flash classdev, torch will be led classdev of the flash classdev. in gb_lights_channel_register()
975 * If it is not a flash related channel (flash, torch or indicator) we in gb_lights_channel_config()
|