Searched full:strapped (Results 1 – 20 of 20) sorted by relevance
| /linux/Documentation/devicetree/bindings/display/panel/ |
| H A D | tpo,tpg110.yaml | 16 driver is strapped up in electronics to the desired resolution
18 SPI. By talking to the TPG110 over SPI, the strapped properties
|
| /linux/Documentation/devicetree/bindings/mfd/ |
| H A D | rohm,bd9571mwv.yaml | 53 power switch (the RSTBMODE pin is strapped low).
59 power switch (the RSTBMODE pin is strapped high).
|
| /linux/Documentation/devicetree/bindings/net/ |
| H A D | ti,dp83867.yaml | 103 This denotes the fact that the board has RX_DV/RX_CTRL pin strapped in
105 software needs to take when this pin is strapped in these modes.
|
| /linux/drivers/usb/cdns3/ |
| H A D | drd.c | 464 dev_dbg(cdns->dev, "Controller strapped to HOST\n"); in cdns_drd_init()
470 dev_dbg(cdns->dev, "Controller strapped to PERIPHERAL\n"); in cdns_drd_init()
|
| /linux/drivers/net/dsa/mv88e6xxx/ |
| H A D | smi.c | 14 * (ADDR[0] is always zero, thus only even SMI addresses can be strapped).
|
| /linux/drivers/watchdog/ |
| H A D | bcm7038_wdt.c | 40 /* MIPS chips strapped for BE will automagically configure the in bcm7038_wdt_write()
|
| /linux/drivers/char/hw_random/ |
| H A D | bcm2835-rng.c | 45 /* MIPS chips strapped for BE will automagically configure the in rng_readl()
|
| /linux/drivers/irqchip/ |
| H A D | irq-brcmstb-l2.c | 187 /* MIPS chips strapped for BE will automagically configure the in brcmstb_l2_intc_probe()
|
| H A D | irq-bcm7120-l2.c | 259 /* MIPS chips strapped for BE will automagically configure the in bcm7120_l2_intc_probe()
|
| /linux/drivers/net/ethernet/broadcom/genet/ |
| H A D | bcmmii.c | 322 * strapped or programmed correctly by the boot loader so we should in bcmgenet_mii_probe()
|
| H A D | bcmgenet.h | 699 /* MIPS chips strapped for BE will automagically configure the \
|
| H A D | bcmgenet.c | 70 /* MIPS chips strapped for BE will automagically configure the in bcmgenet_writel()
|
| /linux/sound/soc/codecs/ |
| H A D | zl38060.c | 14 // - chip must be strapped for "host boot": in this mode, firmware will be
|
| /linux/drivers/net/phy/ |
| H A D | dp83869.c | 808 /* Force speed optimization for the PHY even if it strapped */ in dp83869_config_init()
|
| H A D | broadcom.c | 816 /* The PHY is strapped in RGMII-fiber mode when INTERF_SEL[1:0] in bcm54616s_probe()
|
| /linux/drivers/edac/ |
| H A D | i5100_edac.c | 1003 /* figure out how many ranks, from strapped state of 48GB_Mode input */ in i5100_init_one()
|
| /linux/drivers/net/ethernet/broadcom/asp2/ |
| H A D | bcmasp_intf.c | 982 * been strapped or programmed correctly by the boot loader so in bcmasp_netif_init()
|
| /linux/sound/oss/dmasound/ |
| H A D | dmasound_core.c | 577 /* FIXME: I think that this may be the wrong behaviour when we get strapped in sq_write()
|
| /linux/drivers/gpu/drm/bridge/ |
| H A D | tda998x_drv.c | 1915 * is at the TDA9950 address, with the address pins strapped across in tda998x_create()
|
| /linux/drivers/net/usb/ |
| H A D | lan78xx.c | 2633 "PHY driver not found – assuming RGMII delays are on PCB or strapped for the PHY\n"); in lan78xx_get_phy()
|