| /freebsd/sys/contrib/device-tree/Bindings/spi/ |
| H A D | spi-controller.yaml | 1 # SPDX-License-Identifier: GPL-2.0
3 ---
4 $id: http://devicetree.org/schemas/spi/spi-controller.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: SPI Controller Common Properties
10 - Mark Brown <broonie@kernel.org>
13 SPI busses can be described with a node for the SPI controller device
14 and a set of child nodes for each SPI slave on the bus. The system SPI
15 controller may be described for use in SPI master mode or in SPI slave mode,
20 pattern: "^spi(@.*|-([0-9]|[1-9][0-9]+))?$"
[all …]
|
| H A D | spi-peripheral-props.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/spi/spi-peripheral-props.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Peripheral-specific properties for a SPI bus.
10 Many SPI controllers need to add properties to peripheral devices. They could
11 be common properties like spi-max-frequency, spi-cpha, etc. or they could be
13 need to be defined in the peripheral node because they are per-peripheral and
19 - Mark Brown <broonie@kernel.org>
27 - minimum: 0
[all …]
|
| H A D | icpdas-lp8841-spi-rtc.txt | 1 * ICP DAS LP-8841 SPI Controller for RTC
3 ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO
4 memory register, which acts as an SPI master device.
6 The device uses the standard MicroWire half-duplex transfer timing.
13 - #address-cells: should be 1
15 - #size-cells: should be 0
17 - compatible: should be "icpdas,lp8841-spi-rtc"
19 - reg: should provide IO memory address
21 Requirements to SPI slave nodes:
23 - There can be only one slave device.
[all …]
|
| H A D | spi-bcm63xx-hsspi.txt | 1 Binding for Broadcom BCM6328 High Speed SPI controller
4 - compatible: must contain of "brcm,bcm6328-hsspi".
5 - reg: Base address and size of the controllers memory area.
6 - interrupts: Interrupt for the SPI block.
7 - clocks: phandles of the SPI clock and the PLL clock.
8 - clock-names: must be "hsspi", "pll".
9 - #address-cells: <1>, as required by generic SPI binding.
10 - #size-cells: <0>, also as required by generic SPI binding.
13 - num-cs: some controllers have less than 8 cs signals. Defaults to 8
16 Child nodes as per the generic SPI binding.
[all …]
|
| H A D | spi-nxp-fspi.txt | 4 - compatible : Should be "nxp,lx2160a-fspi"
5 "nxp,imx8qxp-fspi"
6 "nxp,imx8mm-fspi"
7 "nxp,imx8mp-fspi"
8 "nxp,imx8dxl-fspi"
10 - reg : First contains the register location and length,
12 - reg-names : Should contain the resource reg names:
13 - fspi_base: configuration register address space
14 - fspi_mmap: memory mapped address space
15 - interrupts : Should contain the interrupt for the device
[all …]
|
| H A D | qcom,spi-qup.txt | 1 Qualcomm Universal Peripheral (QUP) Serial Peripheral Interface (SPI)
4 and an input FIFO) for serial peripheral interface (SPI) mini-core.
6 SPI in master mode supports up to 50MHz, up to four chip selects, programmable
10 - compatible: Should contain:
11 "qcom,spi-qup-v1.1.1" for 8660, 8960 and 8064.
12 "qcom,spi-qup-v2.1.1" for 8974 and later
13 "qcom,spi-qup-v2.2.1" for 8974 v2 and later.
15 - reg: Should contain base register location and length
16 - interrupts: Interrupt number used by this controller
18 - clocks: Should contain the core clock and the AHB clock.
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/iio/adc/ |
| H A D | adi,ad7944.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Michael Hennerich <Michael.Hennerich@analog.com>
11 - Nuno Sá <nuno.sa@analog.com>
14 A family of pin-compatible single channel differential analog to digital
15 converters with SPI support in a LFCSP package.
21 $ref: /schemas/spi/spi-peripheral-props.yaml#
26 - adi,ad7944
27 - adi,ad7985
[all …]
|
| H A D | adi,ad4000.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Marcelo Schmitt <marcelo.schmitt@analog.com>
13 Analog Devices AD4000 family of Analog to Digital Converters with SPI support.
15 https://www.analog.com/media/en/technical-documentation/data-sheets/ad4000-4004-4008.pdf
16 https://www.analog.com/media/en/technical-documentation/data-sheets/ad4001-4005.pdf
17 https://www.analog.com/media/en/technical-documentation/data-sheets/ad4002-4006-4010.pdf
18 https://www.analog.com/media/en/technical-documentation/data-sheets/ad4003-4007-4011.pdf
19 https://www.analog.com/media/en/technical-documentation/data-sheets/ad4020-4021-4022.pdf
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/rtc/ |
| H A D | epson,rx6110.txt | 4 The Epson RX6110 can be used with SPI or I2C busses. The kind of
8 --------
11 - compatible: should be: "epson,rx6110"
12 - reg : the I2C address of the device for I2C
21 SPI mode
22 --------
25 - compatible: should be: "epson,rx6110"
26 - reg: chip select number
27 - spi-cs-high: RX6110 needs chipselect high
28 - spi-cpha: RX6110 works with SPI shifted clock phase
[all …]
|
| H A D | maxim-ds1302.txt | 1 * Maxim/Dallas Semiconductor DS-1302 RTC
5 The device uses the standard MicroWire half-duplex transfer timing.
12 - compatible : Should be "maxim,ds1302"
14 Required SPI properties:
16 - reg : Should be address of the device chip select within
19 - spi-max-frequency : DS-1302 has 500 kHz if powered at 2.2V,
22 - spi-3wire : The device has a shared signal IN/OUT line.
24 - spi-lsb-first : DS-1302 requires least significant bit first
27 - spi-cs-high: DS-1302 has active high chip select line. This is
32 spi@901c {
[all …]
|
| H A D | nxp,rtc-2123.txt | 1 NXP PCF2123 SPI Real Time Clock
4 - compatible: should be: "nxp,pcf2123"
6 - reg: should be the SPI slave chipselect address
9 - spi-cs-high: PCF2123 needs chipselect high
16 spi-cs-high;
|
| /freebsd/sys/contrib/device-tree/src/arm64/qcom/ |
| H A D | sc7280-idp-ec-h1.dtsi | 1 // SPDX-License-Identifier: BSD-3-Clause
3 * sc7280 EC/H1 over SPI (common between IDP2 and CRD)
11 pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
12 cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
15 compatible = "google,cros-ec-spi";
17 interrupt-parent = <&tlmm>;
19 pinctrl-names = "default";
20 pinctrl-0 = <&ap_ec_int_l>;
21 spi-max-frequency = <3000000>;
22 wakeup-source;
[all …]
|
| H A D | msm8916-pins.dtsi | 1 // SPDX-License-Identifier: GPL-2.0-only
3 * Copyright (c) 2013-2015, The Linux Foundation. All rights reserved.
8 blsp1_uart1_default: blsp1-uart1-default-state {
13 drive-strength = <16>;
14 bias-disable;
17 blsp1_uart1_sleep: blsp1-uart1-sleep-state {
21 drive-strength = <2>;
22 bias-pull-down;
25 blsp1_uart2_default: blsp1-uart2-default-state {
29 drive-strength = <16>;
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/misc/ |
| H A D | eeprom-93xx46.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/misc/eeprom-93xx46.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Microchip 93xx46 SPI compatible EEPROM family dt bindings
10 - Cory Tusar <cory.tusar@pid1solutions.com>
15 - atmel,at93c46
16 - atmel,at93c46d
17 - atmel,at93c56
18 - atmel,at93c66
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/gpio/ |
| H A D | spear_spics.txt | 1 === ST Microelectronics SPEAr SPI CS Driver ===
4 Cell spi controller through its system registers, which otherwise remains under
7 desired by some of the device protocols above spi which expect (multiple)
17 * compatible: should be defined as "st,spear-spics-gpio"
19 * st-spics,peripcfg-reg: peripheral configuration register offset
20 * st-spics,sw-enable-bit: bit offset to enable sw control
21 * st-spics,cs-value-bit: bit offset to drive chipselect low or high
22 * st-spics,cs-enable-mask: chip select number bit mask
23 * st-spics,cs-enable-shift: chip select number program offset
24 * gpio-controller: Marks the device node as gpio controller
[all …]
|
| /freebsd/share/man/man4/ |
| H A D | mx25l.4 | 30 .Nd driver for SpiFlash(tm) compatible non-volatile storage devices
35 .Bd -ragged -offset indent
42 .Bd -literal -offset indent
48 driver provides support for the family of non-volatile storage
63 .Pa /dev/flash/spi? .
72 .Bl -bullet -compact
134 of the SPI bus controller node.
140 The most commonly-used ones are documented below.
145 .Bl -tag -width indent
147 Must be the string "jedec,spi-nor".
[all …]
|
| H A D | at45d.4 | 30 .Nd driver for DataFlash(tm) non-volatile storage devices
35 .Bd -ragged -offset indent
42 .Bd -literal -offset indent
48 driver provides support for the family of non-volatile storage
53 driver supports only the SPI bus versions of each AT45DB device,
75 .Bl -bullet -compact
101 of the SPI bus controller node.
107 The most commonly-used ones are documented below.
112 .Bl -tag -width indent
117 .It Va spi-max-frequency
[all …]
|
| H A D | spigen.4 | 31 .Nd SPI generic I/O device driver
36 .Bd -ragged -offset indent
37 .Cd "device spi"
45 .Bd -literal -offset indent
51 driver provides direct access to a slave device on the SPI bus.
54 device is associated with a single chip-select
56 with that chip-select line asserted.
58 SPI data transfers are inherently bi-directional; there are no separate
71 driver provides access to the SPI slave device with the following
75 .Bl -tag -width indent
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/mfd/ |
| H A D | motorola-cpcap.txt | 4 - compatible : One or both of "motorola,cpcap" or "ste,6556002"
5 - reg : SPI chip select
6 - interrupts : The interrupt line the device is connected to
7 - interrupt-controller : Marks the device node as an interrupt controller
8 - #interrupt-cells : The number of cells to describe an IRQ, should be 2
9 - #address-cells : Child device offset number of cells, should be 1
10 - #size-cells : Child device size number of cells, should be 0
11 - spi-max-frequency : Typically set to 3000000
12 - spi-cs-high : SPI chip select direction
16 The sub-functions of CPCAP get their own node with their own compatible values,
[all …]
|
| H A D | cros-ec.txt | 3 Google's ChromeOS EC is a Cortex-M device which talks to the AP and
6 The EC can be connect through various means (I2C, SPI, LPC, RPMSG) and the
8 its own driver which connects to the top level interface-agnostic EC driver.
9 Other Linux driver (such as cros-ec-keyb for the matrix keyboard) connect to
10 the top-level driver.
13 - compatible: "google,cros-ec-i2c"
14 - reg: I2C slave address
16 Required properties (SPI):
17 - compatible: "google,cros-ec-spi"
18 - reg: SPI chip select
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm64/xilinx/ |
| H A D | zynqmp-zc1751-xm016-dc2.dts | 1 // SPDX-License-Identifier: GPL-2.0+
3 * dts file for Xilinx ZynqMP zc1751-xm016-dc2
5 * (C) Copyright 2015 - 2022, Xilinx, Inc.
6 * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
11 /dts-v1/;
14 #include "zynqmp-clk-ccf.dtsi"
15 #include <dt-bindings/gpio/gpio.h>
16 #include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
19 model = "ZynqMP zc1751-xm016-dc2 RevA";
20 compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
[all …]
|
| /freebsd/sys/dev/qcom_qup/ |
| H A D | qcom_spi.c | 1 /*-
2 * SPDX-License-Identifier: BSD-2-Clause
59 #include <dev/spibus/spi.h>
69 { "qcom,spi-qup-v1.1.1", QCOM_SPI_HW_QPI_V1_1 },
70 { "qcom,spi-qup-v2.1.1", QCOM_SPI_HW_QPI_V2_1 },
71 { "qcom,spi-qup-v2.2.1", QCOM_SPI_HW_QPI_V2_2 },
76 * Flip the CS GPIO line either active or inactive.
78 * Actually listen to the CS polarity.
81 qcom_spi_set_chipsel(struct qcom_spi_softc *sc, int cs, bool active) in qcom_spi_set_chipsel() argument
84 bool invert = !! (cs & SPIBUS_CS_HIGH); in qcom_spi_set_chipsel()
[all …]
|
| /freebsd/sys/contrib/device-tree/src/arm/qcom/ |
| H A D | qcom-ipq4019-ap.dk07.1-c1.dts | 1 // SPDX-License-Identifier: GPL-2.0
4 #include <dt-bindings/gpio/gpio.h>
5 #include "qcom-ipq4019-ap.dk07.1.dtsi"
8 model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK07.1-C1";
9 compatible = "qcom,ipq4019-ap-dk07.1-c1", "qcom,ipq4019";
14 perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
17 spi@78b6000 {
22 serial_1_pins: serial1-state {
26 bias-disable;
29 spi_0_pins: spi-0-state {
[all …]
|
| /freebsd/sys/contrib/device-tree/src/riscv/canaan/ |
| H A D | sipeed_maix_bit.dts | 1 // SPDX-License-Identifier: GPL-2.0+
3 * Copyright (C) 2019-20 Sean Anderson <seanga2@gmail.com>
7 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/leds/common.h>
17 compatible = "sipeed,maix-bit", "sipeed,maix-bitm",
18 "canaan,kendryte-k210";
26 stdout-path = "serial0:115200n8";
29 gpio-leds {
[all …]
|
| /freebsd/sys/contrib/device-tree/src/powerpc/ |
| H A D | ac14xx.dts | 1 // SPDX-License-Identifier: GPL-2.0-or-later
14 #address-cells = <1>;
15 #size-cells = <1>;
26 timebase-frequency = <40000000>; /* 40 MHz (csb/4) */
27 bus-frequency = <160000000>; /* 160 MHz csb bus */
28 clock-frequency = <400000000>; /* 400 MHz ppc core */
49 compatible = "cfi-flash";
51 #address-cells = <1>;
52 #size-cells = <1>;
53 bank-width = <2>;
[all …]
|