xref: /freebsd/sys/contrib/device-tree/src/arm/broadcom/bcm47094-dlink-dir-890l.dts (revision 84943d6f38e936ac3b7a3947ca26eeb27a39f938)
1// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
2/*
3 * Device tree for D-Link DIR-890L
4 * D-Link calls this board "WRGAC36"
5 * this router has the same looks and form factor as D-Link DIR-885L.
6 *
7 * Some differences from DIR-885L include a separate USB2 port, separate LEDs
8 * for USB2 and USB3, a separate VCC supply for the USB2 slot and no
9 * router/extender switch is mounted (there is an empty mount point on the
10 * PCB) so this device is a pure router. Also the LAN ports are in the right
11 * order.
12 *
13 * Based on the device tree for DIR-885L
14 * Copyright (C) 2016 Rafał Miłecki <zajec5@gmail.com>
15 * Copyright (C) 2022 Linus Walleij
16 */
17
18/dts-v1/;
19
20#include "bcm47094.dtsi"
21#include "bcm5301x-nand-cs0-bch1.dtsi"
22
23/ {
24	compatible = "dlink,dir-890l", "brcm,bcm47094", "brcm,bcm4708";
25	model = "D-Link DIR-890L";
26
27	chosen {
28		bootargs = "console=ttyS0,115200 earlycon";
29	};
30
31	memory@0 {
32		device_type = "memory";
33		reg = <0x00000000 0x08000000>,
34		      <0x88000000 0x08000000>;
35	};
36
37	leds {
38		/*
39		 * LED information is derived from the boot log which
40		 * conveniently lists all the LEDs.
41		 */
42		compatible = "gpio-leds";
43
44		led-power-white {
45			label = "bcm53xx:white:power";
46			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
47			linux,default-trigger = "default-on";
48		};
49
50		led-wan-white {
51			label = "bcm53xx:white:wan";
52			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
53		};
54
55		led-power-amber {
56			label = "bcm53xx:amber:power";
57			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
58		};
59
60		led-wan-amber {
61			label = "bcm53xx:amber:wan";
62			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
63		};
64
65		led-usb3-white {
66			label = "bcm53xx:white:usb3";
67			gpios = <&chipcommon 8 GPIO_ACTIVE_LOW>;
68			trigger-sources = <&xhci_port1>;
69			linux,default-trigger = "usbport";
70		};
71
72		led-usb2-white {
73			label = "bcm53xx:white:usb2";
74			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
75			trigger-sources = <&ohci_port1>, <&ehci_port1>;
76			linux,default-trigger = "usbport";
77		};
78
79		led-2ghz {
80			label = "bcm53xx:white:2ghz";
81			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
82		};
83
84		led-5ghz {
85			label = "bcm53xx:white:5ghz";
86			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
87		};
88	};
89
90	gpio-keys {
91		compatible = "gpio-keys";
92
93		button-wps {
94			label = "WPS";
95			linux,code = <KEY_WPS_BUTTON>;
96			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
97		};
98
99		/* Called "factory reset" in the vendor dmesg */
100		button-restart {
101			label = "Reset";
102			linux,code = <KEY_RESTART>;
103			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
104		};
105	};
106
107	/*
108	 * The flash memory is memory mapped at 0x1e000000-0x1fffffff
109	 * 64KB blocks; total size 2MB, same that can be
110	 * found attached to the spi_nor SPI controller.
111	 */
112	nvram@1e1f0000 {
113		compatible = "brcm,nvram";
114		reg = <0x1e1f0000 0x00010000>;
115
116		et0macaddr: et0macaddr {
117		};
118	};
119};
120
121&gmac2 {
122	/*
123	 * The NVRAM curiously does not contain a MAC address
124	 * for et2 so since that is the only ethernet interface
125	 * actually in use on the platform, we use this et0 MAC
126	 * address for et2.
127	 */
128	nvmem-cells = <&et0macaddr>;
129	nvmem-cell-names = "mac-address";
130};
131
132&spi_nor {
133	status = "okay";
134};
135
136&nandcs {
137	/* Spansion S34ML01G2, 128MB with 128KB erase blocks */
138	partitions {
139		compatible = "fixed-partitions";
140		#address-cells = <1>;
141		#size-cells = <1>;
142
143		/*
144		 * This is called "nflash" in the vendor kernel with
145		 * "upgrade" and "rootfs" (probably using OpenWrt
146		 * splitpart). We call it "firmware" like standard tools
147		 * assume. The CFE loader contains incorrect information
148		 * about TRX partitions, ignore this, there are no TRX
149		 * partitions: this device uses SEAMA.
150		 */
151		firmware@0 {
152			compatible = "seama";
153			label = "firmware";
154			reg = <0x00000000 0x08000000>;
155		};
156	};
157};
158
159&usb2 {
160	vcc-gpios = <&chipcommon 21 GPIO_ACTIVE_HIGH>;
161};
162
163&usb3 {
164	vcc-gpios = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
165};
166
167&usb3_phy {
168	status = "okay";
169};
170
171&srab {
172	status = "okay";
173
174	ports {
175		port@0 {
176			label = "lan1";
177		};
178
179		port@1 {
180			label = "lan2";
181		};
182
183		port@2 {
184			label = "lan3";
185		};
186
187		port@3 {
188			label = "lan4";
189		};
190
191		port@4 {
192			label = "wan";
193		};
194
195		port@5 {
196			status = "disabled";
197		};
198
199		port@7 {
200			status = "disabled";
201		};
202
203		port@8 {
204			label = "cpu";
205			phy-mode = "rgmii";
206		};
207	};
208};
209