| /linux/arch/x86/include/asm/ |
| H A D | bitops.h | 304 * AMD64 says BSFL won't clobber the dest reg if x==0; Intel64 says the in variable_ffs()
305 * dest reg is undefined if x==0, but their CPU architect says its in variable_ffs()
361 * AMD64 says BSRL won't clobber the dest reg if x==0; Intel64 says the in fls()
362 * dest reg is undefined if x==0, but their CPU architect says its in fls()
404 * AMD64 says BSRQ won't clobber the dest reg if x==0; Intel64 says the in fls64()
405 * dest reg is undefined if x==0, but their CPU architect says its in fls64()
|
| /linux/drivers/pcmcia/ |
| H A D | soc_common.h | 63 * The PC Card Standard, Release 7, section 4.13.4, says that twIORD
64 * has a minimum value of 165ns. Section 4.13.5 says that twIOWR has
66 * common and attribute memory write timing) says that twWE has a
69 * operation, also section 4.7.4). Section 4.7.3 says that taOE
|
| /linux/drivers/clk/mstar/ |
| H A D | clk-msc313-cpupll.c | 21 * 0x150 -- vendor code says "toggle lpf enable"
24 * 0x160 -- vendor code says "switch to LPF". Clock source config? Register bank?
25 * 0x164 -- vendor code says "from low to high" which seems to mean transition from LPF low to
|
| /linux/Documentation/fb/ |
| H A D | tridentfb.rst | 55 look at the driver output to see what it says when initializing.
59 detection says in all three BIOS selectable situations 2M, 4M, 8M.
|
| /linux/lib/ |
| H A D | ratelimit.c | 39 * Zero interval says never limit, otherwise, non-positive burst in ___ratelimit()
40 * says always limit. in ___ratelimit()
|
| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/mxm/ |
| H A D | nv50.c | 127 /* override dcb sorconf.link, based on what mxm data says */ in mxm_dcb_sanitise_entry()
140 * the descriptor says the connector type should be. in mxm_dcb_sanitise_entry()
143 * and the mxm data says the connector is really HDMI. another in mxm_dcb_sanitise_entry()
|
| /linux/drivers/net/can/spi/mcp251xfd/ |
| H A D | mcp251xfd-ram.c | 111 /* The ethtool doc says: in can_ram_get_layout()
134 /* The ethtool doc says: in can_ram_get_layout()
|
| /linux/drivers/pwm/ |
| H A D | pwm-dwc-core.c | 64 * Specification says timer usage flow is to disable timer, then in __dwc_pwm_configure_timer()
65 * program it followed by enable. It also says Load Count is loaded in __dwc_pwm_configure_timer()
|
| /linux/drivers/mtd/maps/ |
| H A D | physmap-versatile.c | 73 /* The manual says bit 2, the code says bit 3, trust the code */
|
| /linux/arch/x86/tools/ |
| H A D | insn_decoder_test.c | 160 pr_warn("objdump says %d bytes, but insn_get_length() " in main()
161 "says %d\n", nb, insn.length); in main()
|
| /linux/arch/alpha/include/uapi/asm/ |
| H A D | resource.h | 15 * SuS says limits have to be unsigned. Fine, it's unsigned, but
|
| /linux/drivers/iio/proximity/ |
| H A D | d3323aa.c | 216 /* Datasheet says to wait 30 ms after reading the settings. */ in d3323aa_read_settings()
271 /* Datasheet says to wait 30 ms after writing the settings. */ in d3323aa_write_settings()
326 * Datasheet says VDD needs to be low at least for 30 ms. Let's add a in d3323aa_reset()
334 * ready for configuration. Datasheet says that this should happen in d3323aa_reset()
394 * Datasheet says to wait 10 us before setting the configuration. in d3323aa_setup()
|
| /linux/arch/arm/vdso/ |
| H A D | vdsomunge.c | 10 * 0042E) says:
18 * And ELF for the ARM Architecture (ARM IHI 0044E) (Table 4-2) says:
|
| /linux/drivers/staging/greybus/Documentation/firmware/ |
| H A D | firmware.c | 78 printf("Load status says loading failed: %d\n", in update_intf_firmware()
150 printf("Load status says loading failed: %d\n", in update_backend_firmware()
|
| /linux/arch/sparc/include/uapi/asm/ |
| H A D | resource.h | 22 * SuS says limits have to be unsigned.
|
| /linux/Documentation/litmus-tests/rcu/ |
| H A D | RCU+sync+read.litmus | 10 * This is one implication of the RCU grace-period guarantee, which says (among
|
| H A D | RCU+sync+free.litmus | 14 * This is one implication of the RCU grace-period guarantee, which says (among
|
| /linux/tools/lib/subcmd/ |
| H A D | parse-options.h | 81 * PARSE_OPT_OPTARG: says that the argument is optional (not for BOOLEANs)
82 * PARSE_OPT_NOARG: says that this option takes no argument, for CALLBACKs
83 * PARSE_OPT_NONEG: says that this option cannot be negated
|
| /linux/arch/mips/include/uapi/asm/ |
| H A D | resource.h | 25 * SuS says limits have to be unsigned.
|
| /linux/drivers/hid/ |
| H A D | hid-macally.c | 18 * The Macally ikey keyboard says that its logical and usage maximums are both
|
| /linux/arch/powerpc/include/asm/ |
| H A D | papr-sysparm.h | 15 * Parameters Option. Where the spec says "characteristics", we use
|
| /linux/scripts/ |
| H A D | install.sh | 37 # installkernel(8) says the parameters are like follows:
|
| /linux/Documentation/devicetree/bindings/rtc/ |
| H A D | faraday,ftrtc010.yaml | 35 - description: EXTCLK clocks. Faraday calls it CLK1HZ and says the clock
|
| /linux/arch/arm64/boot/dts/freescale/ |
| H A D | fsl-ls1028a-rdb.dts | 218 /* Documentation says 0x51, but must be even and i2cdetect says 0x52 */
|
| /linux/include/linux/reset/ |
| H A D | reset-simple.h | 25 * are set to assert the reset. Note that this says nothing about
|