Searched full:receptacle (Results 1 – 18 of 18) sorted by relevance
/linux/arch/arm/boot/dts/microchip/ |
H A D | at91-foxg20.dts | 150 /* red LED marked "PC7" near mini USB (device) receptacle */
|
/linux/Documentation/devicetree/bindings/usb/ |
H A D | renesas,rzv2m-usb3drd.yaml | 14 * Role swapping function by the ID pin of the Micro-AB receptacle
|
H A D | mediatek,mtu3.yaml | 162 receptacle is TYPE-A and also wants to support dual-role mode.
|
/linux/include/linux/usb/ |
H A D | typec_dp.h | 79 /* Get pin assignment taking plug & receptacle into consideration */
|
H A D | tcpm.h | 128 * a receptacle capable of modal operation. Chip level TCPCI drivers
|
H A D | tcpci.h | 202 * a receptacle capable of modal operation. Chip level TCPCI drivers
|
H A D | pd_vdo.h | 184 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) 247 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
|
/linux/Documentation/devicetree/bindings/phy/ |
H A D | nvidia,tegra186-xusb-padctl.yaml | 37 "port" is typically used to denote the physical USB receptacle. The device 39 abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
|
H A D | nvidia,tegra124-xusb-padctl.yaml | 37 "port" is typically used to denote the physical USB receptacle. The device 39 abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
|
H A D | nvidia,tegra194-xusb-padctl.yaml | 37 "port" is typically used to denote the physical USB receptacle. The device 39 abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
|
H A D | nvidia,tegra210-xusb-padctl.yaml | 37 "port" is typically used to denote the physical USB receptacle. The device 39 abstraction of the signals that are routed to a USB receptacle (i.e. a PHY
|
H A D | phy-stm32-usbphyc.yaml | 90 # to USB connector/receptacle, routing, ESD protection component,... Here is the list of
|
/linux/arch/arm/mach-omap1/ |
H A D | board-palmte.c | 168 .register_dev = 1, /* Mini-B only receptacle */
|
/linux/drivers/usb/mtu3/ |
H A D | mtu3_dr.c | 228 * This is useful in special cases, such as uses TYPE-A receptacle but also
|
/linux/include/dt-bindings/usb/ |
H A D | pd.h | 158 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug) 219 * <23:22> :: Connector type (10b == receptacle, 11b == captive plug)
|
/linux/Documentation/arch/powerpc/ |
H A D | firmware-assisted-dump.rst | 140 reserved, so that it can act as a receptacle for a copy of the boot
|
/linux/drivers/power/supply/ |
H A D | axp288_charger.c | 588 * an OTG host cable is inserted and the ID pin on the micro-B receptacle is
|
/linux/net/tipc/ |
H A D | socket.c | 3223 * @ov: receptacle for option value 3224 * @ol: receptacle for length of option value
|