Home
last modified time | relevance | path

Searched +full:ramp +full:- +full:down (Results 1 – 25 of 116) sorted by relevance

12345

/freebsd/sys/contrib/device-tree/src/arm64/mediatek/
H A Dmt8173-evb.dts1 // SPDX-License-Identifier: GPL-2.0-only
7 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
13 chassis-type = "embedded";
14 compatible = "mediatek,mt8173-evb", "mediatek,mt8173";
31 compatible = "hdmi-connector";
37 remote-endpoint = <&hdmi0_out>;
43 compatible = "linux,extcon-usb-gpio";
44 id-gpios = <&pio 16 GPIO_ACTIVE_HIGH>;
47 usb_p1_vbus: regulator-usb-p1 {
[all …]
H A Dmt8173-elm.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
6 #include <dt-bindings/input/input.h>
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/regulator/dlg,da9211-regulator.h>
9 #include <dt-bindings/gpio/gpio.h>
25 compatible = "pwm-backlight";
27 power-supply = <&bl_fixed_reg>;
28 enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
30 pinctrl-names = "default";
31 pinctrl-0 = <&panel_backlight_en_pins>;
[all …]
H A Dmt8186-corsola.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
5 /dts-v1/;
7 #include <dt-bindings/pinctrl/mt8186-pinfunc.h>
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/input/gpio-keys.h>
11 #include <dt-bindings/regulator/mediatek,mt6397-regulator.h>
26 stdout-path = "serial0:115200n8";
35 backlight_lcd0: backlight-lcd0 {
36 compatible = "pwm-backlight";
[all …]
/freebsd/sys/contrib/device-tree/Bindings/leds/
H A Dleds-lm3697.txt1 * Texas Instruments - LM3697 Highly Efficient White LED Driver
3 The LM3697 11-bit LED driver provides high-
10 - compatible:
12 - reg : I2C slave address
13 - #address-cells : 1
14 - #size-cells : 0
17 - enable-gpios : GPIO pin to enable/disable the device
18 - vled-supply : LED supply
21 - reg : 0 - LED is Controlled by bank A
22 1 - LED is Controlled by bank B
[all …]
H A Dleds-lm3532.txt1 * Texas Instruments - lm3532 White LED driver with ambient light sensing
4 The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
5 programmable over an I2C-compatible interface and has independent
11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
16 - compatible : "ti,lm3532"
17 - reg : I2C slave address
18 - #address-cells : 1
19 - #size-cells : 0
22 - enable-gpios : gpio pin to enable (active high)/disable the device.
23 - ramp-up-us - The Run time ramp rates/step are from one current
[all …]
/freebsd/sys/contrib/device-tree/Bindings/regulator/
H A Dregulator-max77620.txt3 Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply
6 sub-node "regulators" which is child node of device node.
14 -------
[all...]
H A Dregulator.yaml1 # SPDX-License-Identifier: GPL-2.0
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Liam Girdwood <lgirdwood@gmail.com>
11 - Mark Brown <broonie@kernel.org>
14 regulator-nam
[all...]
H A Dsprd,sc2731-regulator.txt3 The SC2731 integrates low-voltage and low quiescent current DCDC/LDO.
5 their own bypass (power-down) control signals. External tantalum or MLCC
9 - compatible: should be "sprd,sc27xx-regulator".
26 compatible = "sprd,sc27xx-regulator";
29 regulator-name = "vddarm0";
30 regulator-min-microvolt = <400000>;
31 regulator-max-microvolt = <1996875>;
32 regulator-ramp-delay = <25000>;
33 regulator-always-on;
37 regulator-name = "vddcama0";
[all …]
H A Dsprd,sc2731-regulator.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
4 $id: http://devicetree.org/schemas/regulator/sprd,sc2731-regulator.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Orson Zhai <orsonzhai@gmail.com>
11 - Baolin Wang <baolin.wang7@gmail.com>
12 - Chunyan Zhang <zhang.lyra@gmail.com>
15 The SC2731 integrates low-voltage and low quiescent current DCDC/LDO.
17 their own bypass (power-down) control signals. It is recommended to use
29 const: sprd,sc2731-regulator
[all …]
H A Dvctrl.txt5 ----------
[all...]
/freebsd/sys/contrib/device-tree/src/arm64/nvidia/
H A Dtegra210-p3450-0000.dts1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
4 #include <dt-bindings/input/gpio-keys.h>
5 #include <dt-bindings/input/linux-event-codes.h>
6 #include <dt-binding
[all...]
H A Dtegra210-p2180.dtsi1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/mfd/max77620.h>
17 stdout-path = "serial0:115200n8";
26 vdd-supply = <&vdd_gpu>;
31 /delete-property/ dmas;
32 /delete-property/ dma-names;
37 /delete-property/ reg-shift;
39 compatible = "nvidia,tegra30-hsuart";
40 reset-names = "serial";
43 compatible = "brcm,bcm43540-bt";
[all …]
H A Dtegra210-smaug.dts1 // SPDX-License-Identifier: GPL-2.0
2 /dts-v1/;
4 #include <dt-bindings/input/input.h>
5 #include <dt-bindings/mfd/max77620.h>
6 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
12 compatible = "google,smaug-rev8", "google,smaug-rev7",
13 "google,smaug-rev6", "google,smaug-rev5",
14 "google,smaug-rev4", "google,smaug-rev3",
15 "google,smaug-rev2", "google,smaug-rev1",
25 stdout-path = "serial0:115200n8";
[all …]
/freebsd/sys/contrib/device-tree/Bindings/sound/
H A Dcs35l33.txt5 - compatible : "cirrus,cs35l33"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VP-supply : power supplies for the device,
15 - reset-gpios : gpio used to reset the amplifier
17 - interrupts : IRQ line info CS35L33.
18 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
26 - cirrus,ramp-rate : On power up, it affects the time from when the power
27 up sequence begins to the time the audio reaches a full-scale output.
28 On power down, it affects the time from when the power-down sequence
[all …]
/freebsd/sys/contrib/device-tree/Bindings/mfd/
H A Dti-lmu.txt6 ------ ---------------------------------
14 - compatible: Should be one of:
20 - reg: I2C slave address.
28 - enable-gpios: A GPIO specifier for hardware enable pin.
29 - ramp-up-us: Current ramping from one brightness level to
31 Range from 2048 us - 117.44 s
32 - ramp-down-us: Current ramping from one brightness level to
34 Range from 2048 us - 117.44 s
35 - ti,brightness-resolution - This determines whether to use 8 bit brightness
47 - backlight: All LMU devices have backlight child nodes.
[all …]
H A Dmediatek,mt6357.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Flora Fu <flora.fu@mediatek.com>
11 - Alexandre Mergnat <amergnat@baylibre.com>
19 - Regulator
20 - RTC
21 - Keys
35 interrupt-controller: true
37 "#interrupt-cells":
[all …]
/freebsd/sys/contrib/device-tree/src/arm/nxp/imx/
H A Dimx53-usbarmory.dts8 * This file is dual-licensed: you can use it either under the terms
47 /dts-v1/;
52 compatible = "inversepath,imx53-usbarmory", "fsl,imx53";
57 stdout-path = &uart1;
66 compatible = "gpio-leds";
67 pinctrl-names = "default";
68 pinctrl-0 = <&pinctrl_led>;
70 led-user {
73 linux,default-trigger = "heartbeat";
83 operating-points = <
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/qcom/
H A Dsdm630-sony-xperia-nile.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/input/gpio-keys.h>
13 #include <dt-bindings/leds/common.h>
17 qcom,msm-id = <318 0>;
18 qcom,board-id = <8 1>;
19 qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00>;
21 /* This part enables graphical output via bootloader-enabled display */
25 #address-cells = <2>;
[all …]
H A Dmsm8998-sony-xperia-yoshino.dtsi1 // SPDX-License-Identifier: BSD-3-Clause
8 #include <dt-bindings/input/input.h>
9 #include <dt-bindings/leds/common.h>
10 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
18 qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
19 qcom,board-id = <8 0>;
23 compatible = "gpio-gate-clock";
24 pinctrl-0 = <&div_clk1>;
25 pinctrl-names = "default";
27 #clock-cells = <0>;
[all …]
H A Dsdm670-google-sargo.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Device tree for Google Pixel 3a, adapted from google-blueline device tree,
4 * xiaomi-lavender device tree, and oneplus-common device tree.
9 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
14 #include <dt-bindings/power/qcom-rpmpd.h>
19 /delete-node/ &mpss_region;
20 /delete-node/ &venus_mem;
[all …]
/freebsd/sys/contrib/device-tree/Bindings/gpio/
H A Dgpio-delay.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/gpio/gpio-delay.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Alexander Stein <linux@ew.tq-group.com>
16 +----------+ +-----------+
23 | [IOx|-------| |--+-----|-----+ |
26 +----------+ --- C +-----------+
27 ---
29 -
[all …]
/freebsd/sys/contrib/device-tree/src/arm/renesas/
H A Dr8a7745-iwg22d-sodimm.dts1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the iWave-RZG1E SODIMM carrier board
9 * SSI-SGTL5000
21 * You can use Volume Ramp
23 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
24 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
25 * amixer set "DVC Out Ramp" o
[all...]
H A Diwg20d-q7-common.dtsi1 // SPDX-License-Identifier: GPL-2.0
3 * Device Tree Source for the iWave-RZ/G1M/G1N Qseven carrier board
9 * SSI-SGTL5000
21 * You can use Volume Ramp
23 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
24 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
25 * amixer set "DVC Out Ramp" on
27 * amixer set "DVC Out" 80% // Volume Down
40 stdout-path = "serial0:115200n8";
44 compatible = "fixed-clock";
[all …]
/freebsd/sys/contrib/device-tree/src/arm/ti/omap/
H A Domap4-droid-bionic-xt875.dts1 // SPDX-License-Identifier: GPL-2.0-only
2 /dts-v1/;
4 #include "motorola-mapphone-xt8xx.dtsi"
8 compatible = "motorola,droid-bionic", "ti,omap4430", "ti,omap4";
11 stdout-path = &uart3;
21 keypad,num-row
[all...]
/freebsd/sys/contrib/device-tree/src/arm/qcom/
H A Dqcom-pm8941.dtsi1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/iio/qcom,spmi-vadc.h>
3 #include <dt-bindings/interrupt-controller/irq.h>
4 #include <dt-bindings/spmi/spmi.h>
8 thermal-zones {
9 pm8941-therma
[all...]

12345