Searched full:pulsing (Results 1 – 20 of 20) sorted by relevance
| /linux/include/linux/ |
| H A D | leds-expresswire.h | 4 * This protocol works by pulsing the ExpressWire IC's control GPIO.
|
| /linux/Documentation/devicetree/bindings/leds/backlight/ |
| H A D | kinetic,ktd2801.yaml | 15 or by pulsing the GPIO line to set the backlight level. This is called
|
| /linux/drivers/leds/ |
| H A D | leds-expresswire.c | 4 * This protocol works by pulsing the ExpressWire IC's control GPIO.
|
| H A D | leds-spi-byte.c | 20 * * Mode: 01 -> pulsing pattern (min -> max -> min) with an interval. From
|
| H A D | leds-tca6507.c | 6 * separate lines either by holding them low, or by pulsing them
|
| /linux/Documentation/devicetree/bindings/leds/ |
| H A D | ti,tca6507.yaml | 14 7 separate lines either by holding them low, or by pulsing them with modulated
|
| /linux/arch/arm/mach-lpc32xx/ |
| H A D | serial.c | 139 /* Disable IrDA pulsing support on UART6 */ in lpc32xx_serial_init()
|
| /linux/drivers/usb/chipidea/ |
| H A D | otg_fsm.c | 538 * Start SRP pulsing by data-line pulsing,
539 * no v-bus pulsing followed
|
| /linux/drivers/iio/dac/ |
| H A D | ti-dac7612.c | 141 * event can change the value of all DACs by pulsing down the LOADDACs in dac7612_probe()
|
| /linux/drivers/input/misc/ |
| H A D | powermate.c | 24 * intensity, or to a rhythmic pulsing. Several patterns and speeds are available.
254 …bits 8-16: 9 bits: pulsing speed modifier (0 ... 510); 0-254 = slower, 255 = standard, 256-510 = … in powermate_input_event()
|
| /linux/include/linux/usb/ |
| H A D | otg-fsm.h | 109 * @data_pulse: TRUE when the B-device is performing data line pulsing
|
| /linux/arch/arm/boot/dts/amlogic/ |
| H A D | meson8b-ec100.dts | 81 * "breathing"/pulsing effect until the power is fully
|
| /linux/drivers/usb/phy/ |
| H A D | phy-fsl-usb.h | 271 #define TB_VBUS_PLS (30) /* time to keep vbus pulsing asserted */
|
| /linux/drivers/net/ethernet/aquantia/atlantic/ |
| H A D | aq_ptp.c | 371 "Enable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
375 "Disable GPIO %d pulsing, start time %llu, period %u\n", in aq_ptp_hw_pin_conf()
|
| /linux/drivers/net/phy/ |
| H A D | intel-xway.c | 126 /* Pulsing Configuration */
|
| /linux/drivers/pmdomain/imx/ |
| H A D | imx8mp-blk-ctrl.c | 430 * power domain is powered down. To ensure the proper reset pulsing, in imx8mp_hdmi_power_notifier()
|
| /linux/drivers/comedi/drivers/ |
| H A D | s626.c | 1389 /* Start ADC by pulsing GPIO1. */ in s626_reset_adc()
1516 /* Start ADC by pulsing GPIO1 low */ in s626_ai_insn_read()
|
| /linux/drivers/gpu/drm/bridge/synopsys/ |
| H A D | dw-hdmi.c | 304 * other than pulsing the SDA line. in dw_hdmi_i2c_unwedge()
|
| /linux/drivers/media/pci/bt8xx/ |
| H A D | bttv-cards.c | 4370 * connection prior to establish a new one, pulsing the STROBE pin.
|
| /linux/drivers/usb/dwc2/ |
| H A D | hcd.c | 2055 /* Set external TS Dline pulsing bit if needed */ in dwc2_core_init()
|