| /linux/Documentation/driver-api/gpio/ |
| H A D | drivers-on-gpio.rst | 42 the system by pulling a GPIO line and will register a restart handler so
46 system down by pulling a GPIO line and will register a pm_power_off()
75 regulator providing a certain voltage by pulling a GPIO line, integrating
|
| /linux/mm/ |
| H A D | page_reporting.h | 30 * threshold then it will start the process of pulling some pages and
|
| /linux/arch/hexagon/kernel/ |
| H A D | vmlinux.lds.S | 11 #include <asm/cache.h> /* and now we're pulling cache line size */
|
| /linux/Documentation/devicetree/bindings/input/ |
| H A D | cypress,tm2-touchkey.yaml | 43 e.g. for pulling up the interrupt line or the I2C pins.
|
| /linux/Documentation/w1/masters/ |
| H A D | w1-uart.rst | 28 pulling the line low, which is used by the driver to evaluate the result of
|
| /linux/net/sched/ |
| H A D | sch_multiq.c | 101 * pulling an skb to avoid head-of-line blocking. in multiq_dequeue()
133 * pulling an skb to avoid head-of-line blocking. in multiq_peek()
|
| /linux/Documentation/leds/ |
| H A D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
|
| /linux/drivers/scsi/aacraid/ |
| H A D | dpcsup.c | 50 * Keep pulling response QEs off the response queue and waking in aac_response_normal()
167 * Keep pulling response QEs off the response queue and waking in aac_command_normal()
|
| /linux/drivers/clk/ux500/ |
| H A D | reset-prcc.c | 29 * the reset by pulling the line low. SET take the device out of
|
| /linux/Documentation/i2c/ |
| H A D | gpio-fault-injection.rst | 100 test and then pulling SDA low for some time. So, the I2C address sent out
|
| /linux/Documentation/w1/ |
| H A D | w1-generic.rst | 8 Devices communicate on the bus by pulling the signal to ground via an open
|
| /linux/tools/testing/selftests/drivers/sdsi/ |
| H A D | sdsi_test.py | 190 # Short wait needed to allow file to close before pulling driver
|
| /linux/Documentation/maintainer/ |
| H A D | rebasing-and-merging.rst | 127 requests, and upstream maintainers should verify the tags when pulling
|
| /linux/net/bluetooth/ |
| H A D | af_bluetooth.c | 515 /* Pulling partial data */ in bt_sock_stream_recvmsg()
521 /* Pulling all frag data */ in bt_sock_stream_recvmsg()
|
| /linux/Documentation/doc-guide/ |
| H A D | contributing.rst | 158 Note that the most value comes from pulling in the documentation for
|
| /linux/arch/arm/kernel/ |
| H A D | entry-header.S | 211 @ IRQs off again before pulling preserved data off the stack
|
| /linux/arch/arm/boot/dts/samsung/ |
| H A D | exynos5250-spring.dts | 361 * double-pulling gets us out of spec in some cases.
|
| H A D | exynos5250-snow-common.dtsi | 452 * double-pulling gets us out of spec in some cases.
|
| /linux/drivers/gpio/ |
| H A D | gpio-pcf857x.c | 354 * the '75c doesn't have a current source pulling high. in pcf857x_probe()
|
| /linux/tools/tracing/rtla/src/ |
| H A D | timerlat_top.c | 532 err_msg("Error pulling BPF data\n"); in timerlat_top_bpf_main_loop()
|
| /linux/drivers/comedi/drivers/ |
| H A D | das16m1.c | 25 * pulling the data across the ISA bus. I timed the interrupt handler, and it
|
| H A D | pcmuio.c | 209 * effectively pulling it low.
|
| /linux/drivers/net/wireguard/ |
| H A D | receive.c | 283 /* Another ugly situation of pushing and pulling the header so as to in decrypt_packet()
|
| /linux/drivers/md/bcache/ |
| H A D | alloc.c | 531 * The ideas is if you've got multiple tasks pulling data into the cache at the
|
| /linux/drivers/mtd/nand/raw/ |
| H A D | mtk_nand.c | 625 * 31:28: tpoecs, minimum required time for CS post pulling down after in mtk_nfc_setup_interface()
627 * 27:22: tprecs, minimum required time for CS pre pulling down before in mtk_nfc_setup_interface()
|