Home
last modified time | relevance | path

Searched full:optimum (Results 1 – 25 of 28) sorted by relevance

12

/linux/include/linux/mfd/
H A Dac100.h106 #define AC100_ADC_DAP_OPT 0x95 /* AGC Optimum */
126 #define AC100_DAC_DAP_OPT 0xb1 /* DRC optimum */
/linux/include/linux/
H A Drational.h8 * e.g. when calculating optimum numerator/denominator pairs for
/linux/Documentation/ABI/testing/
H A Dsysfs-bus-iio-isl295017 which sets the analog signal levels at an optimum
/linux/Documentation/scsi/
H A DBusLogic.rst307 may be used to load "Optimum Performance" settings which allow UltraSCSI
310 the "Optimum Performance" settings are loaded.
377 used to load "Optimum Performance" settings which allow UltraSCSI speed to be
380 "Optimum Performance" settings are loaded.
/linux/drivers/accel/ivpu/
H A Divpu_hw.h33 * Pll ratio for the efficiency frequency. The VPU has optimum
/linux/arch/alpha/lib/
H A Dev6-copy_page.S29 conditions were such that I could not reach this optimum rate on
/linux/drivers/scsi/aic7xxx/
H A Dqueue.h42 * macro for this purpose for optimum efficiency. A singly-linked list may
53 * should use the explicit macro for this purpose for optimum efficiency.
/linux/drivers/net/wireless/ti/wlcore/
H A Dconf.h981 * Minimum required free tx memory blocks in order to assure optimum
989 * Minimum required free rx memory blocks in order to assure optimum
/linux/arch/s390/kernel/
H A Dhiperdispatch.c11 * Dynamically calculates the optimum number of high capacity COREs
/linux/Documentation/devicetree/bindings/pci/
H A Dnvidia,tegra194-pcie.yaml155 optimum number of FC (Flow Control) credits with downstream devices:
/linux/Documentation/networking/device_drivers/ethernet/freescale/dpaa2/
H A Doverview.rst382 There is typically one DPIO object per physical CPU for optimum
/linux/drivers/mtd/chips/
H A Dcfi_cmdset_0020.c99 printk(" Vcc Logic Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
102 printk(" Vpp Programming Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
H A Dcfi_cmdset_0001.c163 printk(" Vcc Logic Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
166 printk(" Vpp Programming Supply Optimum Program/Erase Voltage: %d.%d V\n", in cfi_tell_features()
/linux/Documentation/arch/powerpc/
H A Dhvcs.rst10 .. NOTE:Eight space tabs are the optimum editor setting for reading this file.
/linux/Documentation/admin-guide/pm/
H A Dcpufreq.rst661 The frequency boost mechanism is generally intended to help to achieve optimum
/linux/fs/smb/client/
H A Dcifspdu.h1021 boundary and optimum performance here */
1041 boundary and optimum performance here */
/linux/Documentation/mm/damon/
H A Ddesign.rst311 Hence the optimum value of ``aggregation interval`` depends on the access
/linux/drivers/scsi/aic94xx/
H A Daic94xx_sds.c1238 * a optimum balance of 50mus for ERASE which works well in asd_chk_write_status()
/linux/drivers/dma/
H A Dtegra186-gpc-dma.c825 * len to calculate the optimum burst size in get_burst_size()
/linux/sound/oss/dmasound/
H A Ddmasound_core.c594 The strategy - possibly not optimum - is to kill _POST status if we in sq_write()
/linux/drivers/media/dvb-frontends/
H A Ddrxd_hard.c2424 u32 ulRfAgcSettleLevel = 528; /* Optimum value for MT2060 */ in CDRXD()
/linux/drivers/mtd/nand/raw/
H A Dcadence-nand-controller.c2389 * The idea of those calculation is to get the optimum value in cadence_nand_setup_interface()
/linux/sound/pci/
H A Des1968.c768 /* next, back off prescaler whilst getting divider into optimum range */ in wave_get_register()
/linux/drivers/net/ethernet/natsemi/
H A Dnatsemi.c1204 /* On page 78 of the spec, they recommend some settings for "optimum in init_phy_fixup()
/linux/drivers/net/wireless/ath/ath5k/
H A Dphy.c1150 /* Set optimum value for early revisions (on pci-e chips) */ in ath5k_hw_rfregs_init()

12