| /linux/Documentation/hid/ |
| H A D | hidraw.rst | 51 On a device which uses numbered reports, the first byte of the returned data
53 byte. For devices which do not use numbered reports, the report data
64 number. If the device does not use numbered reports, the first byte should
117 which do not use numbered reports, set the first byte to 0. The report data
126 number of the requested report. For devices which do not use numbered
129 device. For devices which do not use numbered reports, the report data will
|
| /linux/Documentation/devicetree/bindings/iio/adc/ |
| H A D | ti,ads131e08.yaml | 89 Up to 4 channels, numbered from 0 to 3 for ti,ads131e04.
90 Up to 6 channels, numbered from 0 to 5 for ti,ads131e06.
91 Up to 8 channels, numbered from 0 to 7 for ti,ads131e08.
|
| H A D | st,stm32-adc.yaml | 295 - 16 channels, numbered from 0 to 15 (for in0..in15) on stm32f4
296 - 19 channels, numbered from 0 to 18 (for in0..in18) on stm32mp13.
297 - 20 channels, numbered from 0 to 19 (for in0..in19) on stm32h7 and
307 <vinp vinn>, <vinp vinn>,... vinp and vinn are numbered from 0 to 19.
|
| /linux/arch/s390/include/asm/ |
| H A D | bitops.h | 9 * Within a word, bits are numbered LSB first. Lot's of places make
16 * end up numbered:
20 * The bits are numbered:
81 * The bits are numbered:
|
| /linux/Documentation/devicetree/bindings/dma/ |
| H A D | apple,admac.yaml | 13 The controller has been seen with up to 24 channels. Even-numbered channels
14 are TX-only, odd-numbered are RX-only. Individual channels are coupled to
|
| /linux/Documentation/devicetree/bindings/media/ |
| H A D | cdns,csi2tx.txt | 26 port nodes are numbered as follows.
39 the endpoints are not numbered.
|
| /linux/arch/s390/lib/ |
| H A D | find.c | 3 * MSB0 numbered special bitops handling.
5 * The bits are numbered:
|
| /linux/Documentation/devicetree/bindings/display/bridge/ |
| H A D | thine,thc63lvd1024.yaml | 34 even-numbered pixels are received on port@0 and odd-numbered pixels on
|
| /linux/include/linux/mfd/ |
| H A D | adp5585.h | 111 * Bank 0 covers pins "GPIO 1/R0" to "GPIO 6/R5", numbered 0 to 5 by the
112 * driver, and bank 1 covers pins "GPIO 7/C0" to "GPIO 11/C4", numbered 6 to
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | mediatek,mt65xx-pinctrl.yaml | 31 pins-are-numbered:
34 Specify the subnodes are using numbered pinmux to specify pins. (UNUSED)
|
| /linux/Documentation/filesystems/iomap/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/input/devices/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/arch/nios2/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/filesystems/ext4/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/arch/loongarch/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/PCI/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/filesystems/xfs/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/arch/mips/ |
| H A D | index.rst | 9 :numbered:
|
| /linux/Documentation/input/ |
| H A D | input_kapi.rst | 10 :numbered:
|
| H A D | input_uapi.rst | 10 :numbered:
|
| /linux/arch/powerpc/lib/ |
| H A D | copyuser_64.S | 17 #define sLd sld /* Shift towards low-numbered address. */
18 #define sHd srd /* Shift towards high-numbered address. */
20 #define sLd srd /* Shift towards low-numbered address. */
21 #define sHd sld /* Shift towards high-numbered address. */
|
| /linux/tools/testing/selftests/powerpc/copyloops/ |
| H A D | copyuser_64.S | 17 #define sLd sld /* Shift towards low-numbered address. */
18 #define sHd srd /* Shift towards high-numbered address. */
20 #define sLd srd /* Shift towards low-numbered address. */
21 #define sHd sld /* Shift towards high-numbered address. */
|
| /linux/Documentation/translations/zh_CN/process/ |
| H A D | development-process.rst | 15 :numbered:
|
| /linux/tools/include/uapi/linux/ |
| H A D | kcmp.h | 25 __u32 toff; /* target offset within same numbered sequence */
|
| /linux/include/uapi/linux/ |
| H A D | kcmp.h | 25 __u32 toff; /* target offset within same numbered sequence */
|