| /linux/Documentation/devicetree/bindings/regulator/ |
| H A D | richtek,rtmv20-regulator.yaml | 38 load current pulse delay in microsecond after strobe pin pulse high.
45 Load current pulse width in microsecond after strobe pin pulse high.
52 Fsin1 pulse high delay in microsecond after vsync signal pulse high.
59 Fsin1 pulse high width in microsecond after vsync signal pulse high.
66 Fsin2 pulse high delay in microsecond after vsync signal pulse high.
73 Fsin2 pulse high width in microsecond after vsync signal pulse high.
79 description: Eye safety function pulse width limit in microsecond.
|
| /linux/drivers/gpu/drm/amd/display/include/ |
| H A D | ddc_service_types.h | 87 /* Maximum additional audio delay in microsecond (us) */
89 /* Audio latency value in microsecond (us) */
91 /* Interlace video latency value in microsecond (us) */
93 /* Progressive video latency value in microsecond (us) */
|
| /linux/arch/x86/include/asm/ |
| H A D | i8259.h | 40 * must be at least one microsecond, so be safe here: in inb_pic()
52 * must be at least one microsecond, so be safe here: in outb_pic()
|
| /linux/drivers/md/dm-vdo/indexer/ |
| H A D | funnel-requestqueue.c | 40 MICROSECOND = 1000 * NANOSECOND, enumerator
41 MILLISECOND = 1000 * MICROSECOND,
42 DEFAULT_WAIT_TIME = 20 * MICROSECOND,
|
| /linux/Documentation/devicetree/bindings/thermal/ |
| H A D | thermal-idle.yaml | 36 The idle duration in microsecond the device should cool down.
40 The exit latency constraint in microsecond for the injected idle state
|
| /linux/tools/tracing/rtla/tests/ |
| H A D | hwnoise.t | 10 check "detect noise higher than one microsecond" \
|
| /linux/Documentation/userspace-api/media/rc/ |
| H A D | lirc-get-rec-resolution.rst | 36 signals can only be reported in 50 microsecond steps.
|
| /linux/drivers/comedi/drivers/ |
| H A D | comedi_test.c | 322 /* round convert_arg to nearest microsecond */ in waveform_ai_cmdtest()
337 /* round scan_begin_arg to nearest microsecond */ in waveform_ai_cmdtest()
593 /* round scan_begin_arg to nearest microsecond */ in waveform_ao_cmdtest()
754 "%s: %u microvolt, %u microsecond waveform attached\n", in waveform_common_attach()
|
| /linux/drivers/scsi/isci/ |
| H A D | probe_roms.h | 126 * activity in increments of a microsecond, it can be in increments of
143 * outbound traffic in increments of a microsecond.
|
| /linux/drivers/iio/light/ |
| H A D | cm3232.c | 126 * @val2: pointer of int to load the integration time (microsecond).
155 * @val2: integration time in microsecond.
|
| /linux/arch/arm64/include/asm/ |
| H A D | rqspinlock.h | 24 * up at microsecond granularity.
|
| /linux/Documentation/devicetree/bindings/gpio/ |
| H A D | sprd,gpio-eic.yaml | 37 (microsecond resolution) to generate interrupts by level or edge trigger.
|
| /linux/arch/arm/mach-tegra/ |
| H A D | sleep.h | 42 /* waits until the microsecond counter (base) is > rn */
|
| /linux/drivers/gpu/drm/amd/display/dc/ |
| H A D | dc_ddc_types.h | 52 /* delay, in 100-microsecond units */
|
| /linux/arch/m68k/include/asm/ |
| H A D | delay.h | 98 * per microsecond
|
| /linux/Documentation/trace/ |
| H A D | hwlat_detector.rst | 22 you are trying to keep event service latencies down in the microsecond range.
|
| /linux/drivers/accel/ivpu/ |
| H A D | vpu_boot_api.h | 398 /* Microsecond value for DCT active cycle */
400 /* Microsecond value for DCT inactive cycle */
|
| /linux/Documentation/tools/rtla/ |
| H A D | rtla-hwnoise.rst | 43 The tool is set to detect any noise higher than *one microsecond*,
|
| /linux/arch/arm/mach-omap2/ |
| H A D | vc.c | 239 /* Convert microsecond value to number of 32kHz clock cycles */
519 * omap4_usec_to_val_scrm - convert microsecond value to SCRM module bitfield
524 * Converts microsecond value to OMAP4 SCRM bitfield. Bitfield is
|
| /linux/drivers/gpu/drm/nouveau/nvkm/subdev/pmu/fuc/ |
| H A D | kernel.fuc | 277 // calculate the number of ticks in the specified microsecond delay
304 // calculate the number of ticks in the specified microsecond delay
|
| /linux/drivers/clocksource/ |
| H A D | timer-tegra186.c | 158 /* select microsecond source */ in tegra186_wdt_enable()
261 /* Get the current counter value in microsecond. */ in tegra186_wdt_get_timeleft()
|
| /linux/drivers/clk/ux500/ |
| H A D | reset-prcc.c | 77 * Assert reset and then release it. The one microsecond in u8500_prcc_reset()
|
| /linux/drivers/pwm/ |
| H A D | pwm-visconti.c | 74 * microsecond resolution and so can divide by in visconti_pwm_apply()
|
| /linux/drivers/power/sequencing/ |
| H A D | pwrseq-thead-gpu.c | 60 * a very high GPU clock frequency, a delay of 1 microsecond is in pwrseq_thead_gpu_enable()
|
| /linux/drivers/staging/rtl8723bs/include/ |
| H A D | hal_intf.h | 87 /* Unit in microsecond. 0 means disable this function. */
|