Home
last modified time | relevance | path

Searched +full:micbias +full:- +full:lvl (Results 1 – 16 of 16) sorted by relevance

/freebsd/sys/contrib/device-tree/Bindings/sound/
H A Dda7219.txt8 - compatible : Should be "dlg,da7219"
9 - reg: Specifies the I2C slave address
11 - interrupts : IRQ line info for DA7219.
12 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
15 - VDD-supply: VDD power supply for the device
16 - VDDMIC-supply: VDDMIC power supply for the device
17 - VDDIO-supply: VDDIO power supply for the device
22 - interrupt-names : Name associated with interrupt line. Should be "wakeup" if
24 - wakeup-source: Flag to indicate this device can wake system (suspend/resume).
26 - #clock-cells : Should be set to '<1>', two clock sources provided;
[all …]
H A Dcs42l52.txt5 - compatible : "cirrus,cs42l52"
7 - reg : the I2C address of the device for I2C
11 - cirrus,reset-gpio : GPIO controller's phandle and the number
14 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
21 - cirrus,mica-differential-cfg : boolean, If present, then the MICA input is configured
23 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
25 - cirrus,micb-differential-cfg : boolean, If present, then the MICB input is configured
27 Single-ended input. Single-ended mode allows for MIC1 or MIC2 muxing for input.
29 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin
42 reset-gpio = <&gpio 10 0>;
[all …]
H A Dcs42l56.txt5 - compatible : "cirrus,cs42l56"
7 - reg : the I2C address of the device for I2C
9 - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
14 - cirrus,gpio-nreset : GPIO controller's phandle and the number
17 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
25 as a pseudo-differential input referenced to AIN1REF/AIN3A.
27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
28 as a pseudo-differential input referenced to AIN2REF/AIN3B.
30 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
[all …]
H A Ddialog,da7219.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schema
[all...]
H A Dcs53l30.txt5 - compatible : "cirrus,cs53l30"
7 - reg : the I2C address of the device
9 - VA-supply, VP-supply : power supplies for the device,
14 - reset-gpios : a GPIO spec for the reset pin.
16 - mute-gpios : a GPIO spec for the MUTE pin. The active state can be either
20 - cirru
[all...]
H A Dqcom,msm8916-wcd-analog.txt8 - compatible = "qcom,pm8916-wcd-analog-codec";
9 - reg: represents the slave base address provided to the peripheral.
10 - interrupts: List of interrupts in given SPMI peripheral.
11 - interrupt-names: Names specified to above list of interrupts in same
13 "cdc_spk_cnp_int" - Speaker click and pop interrupt.
14 "cdc_spk_clip_int" - Speaker clip interrupt.
15 "cdc_spk_ocp_int" - Speaker over current protect interrupt.
16 "mbhc_ins_rem_det1" - jack insert removal detect interrupt 1.
17 "mbhc_but_rel_det" - button release interrupt.
18 "mbhc_but_press_det" - button press event
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/mediatek/
H A Dmt8183-kukui-audio-da7219.dtsi1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
10 pinctrl-names = "default";
11 pinctrl-0 = <&da7219_pins>;
14 interrupts-extended = <&pio 165 IRQ_TYPE_LEVEL_LOW>;
16 dlg,micbias-lvl = <2600>;
17 dlg,mic-amp-in-sel = "diff";
18 VDD-supply = <&pp1800_alw>;
19 VDDMIC-supply = <&pp3300_alw>;
20 VDDIO-supply = <&pp1800_alw>;
25 dlg,adc-1bit-rpt = <1>;
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/qcom/
H A Dmsm8916-motorola-harpia.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-motorola-common.dtsi"
10 chassis-type = "handset";
20 interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>;
22 pinctrl-0 = <&battery_alert_default>;
23 pinctrl-names = "default";
25 maxim,rsns-microohm = <10000>;
26 maxim,over-heat-temp = <600>;
27 maxim,cold-temp = <(-200)>;
[all …]
H A Dmsm8916-wingtech-wt865x8.dtsi1 // SPDX-License-Identifier: GPL-2.0-only
3 #include "msm8916-pm8916.dtsi"
4 #include "msm8916-modem-qdsp6.dtsi"
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
17 stdout-path = "serial0";
20 headphones_switch: audio-switch {
21 compatible = "simple-audio-amplifier";
23 pinctrl-0 = <&headphones_switch_default>;
24 pinctrl-names = "default";
[all …]
H A Dmsm8916-acer-a1-724.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/irq.h>
11 #include <dt-bindings/leds/common.h>
14 * NOTE: The original firmware from Acer can only boot 32-bit kernels.
15 * To boot this device tree using arm64 it is necessary to flash 64-bit
[all …]
H A Dmsm8916-lg-m216.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
13 chassis-type = "handset";
22 stdout-path = "serial0";
26 compatible = "simple-battery";
27 voltage-min-design-microvolt = <3300000>;
28 voltage-max-design-microvolt = <4350000>;
[all …]
H A Dmsm8916-gplus-fl8005a.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/leds/common.h>
15 chassis-type = "tablet";
24 stdout-path = "serial0";
28 compatible = "simple-battery";
[all …]
H A Dmsm8916-longcheer-l8910.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
16 chassis-type = "handset";
25 stdout-path = "serial0";
[all …]
H A Dmsm8916-longcheer-l8150.dts1 // SPDX-License-Identifier: GPL-2.0-only
3 /dts-v1/;
5 #include "msm8916-pm8916.dtsi"
6 #include "msm8916-modem-qdsp6.dtsi"
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/input.h>
10 #include <dt-bindings/interrupt-controller/irq.h>
11 #include <dt-bindings/leds/common.h>
16 chassis-type = "handset";
25 stdout-path = "serial0";
[all …]
H A Dmsm8916-huawei-g7.dts1 // SPDX-License-Identifier: GPL-2.0-only
6 /dts-v1/;
8 #include "msm8916-pm8916.dtsi"
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/interrupt-controlle
[all...]
/freebsd/sys/contrib/device-tree/src/arm64/rockchip/
H A Drk3399-gru.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
5 * Copyright 2016-2017 Google, Inc
8 #include <dt-bindings/input/input.h>
9 #include "rk3399-op1.dtsi"
18 stdout-path = "serial2:115200n8";
27 * - Rails that only connect to the EC (or devices that the EC talks to)
29 * - Rails _are_ included if the rails go to the AP even if the AP
38 * - The EC controls the enable and the EC always enables a rail as
40 * - The rails are actually connected to each other by a jumper and
45 ppvar_sys: ppvar-sys {
[all …]