Home
last modified time | relevance | path

Searched +full:led +full:- +full:0 +full:- +full:mode (Results 1 – 25 of 969) sorted by relevance

12345678910>>...39

/freebsd/sys/contrib/device-tree/Bindings/leds/
H A Dleds-lp55xx.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-lp55xx.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI/National Semiconductor LP55xx and LP8501 LED Drivers
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
15 LED Drivers.
27 - national,lp5521
28 - national,lp5523
[all …]
H A Dleds-lm3532.txt1 * Texas Instruments - lm3532 White LED driver with ambient light sensing
4 The LM3532 provides the 3 high-voltage, low-side current sinks. The device is
5 programmable over an I2C-compatible interface and has independent
7 method allows for different LED currents in each current sink thus allowing
11 each with 32 internal voltage setting resistors, 8-bit logarithmic and linear
16 - compatible : "ti,lm3532"
17 - reg : I2C slave address
18 - #address-cells : 1
19 - #size-cells : 0
22 - enable-gpios : gpio pin to enable (active high)/disable the device.
[all …]
H A Dleds-lp55xx.txt1 Binding for TI/National Semiconductor LP55xx Led Drivers
4 - compatible: one of
11 - reg: I2C slave address
12 - clock-mode: Input clock mode, (0: automode, 1: internal, 2: external)
15 - led-cur: Current setting at each led channel (mA x10, 0 if led is not connected)
16 - max-cur: Maximun current at each led channel.
19 - enable-gpio: GPIO attached to the chip's enable pin
20 - label: Used for naming LEDs
21 - pwr-sel: LP8501 specific property. Power selection for output channels.
22 0: D1~9 are connected to VDD
[all …]
H A Dcommon.yaml1 # SPDX-License-Identifier: GPL-2.0-only
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jacek Anaszewski <jacek.anaszewski@gmail.com>
11 - Pavel Machek <pavel@ucw.cz>
14 LED and flash LED devices provide the same basic functionality as current
15 regulators, but extended with LED and flash LED specific features like
16 blinking patterns, flash timeout, flash faults and external flash strobe mode.
18 Many LED devices expose more than one current output that can be connected
19 to one or more discrete LED component. Since the arrangement of connections
[all …]
H A Dti,tps61310.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Texas Instruments TPS6131X flash LED driver
10 - Matthias Fend <matthias.fend@emfend.at>
13 The TPS61310/TPS61311 is a flash LED driver with I2C interface.
15 The TPS6131x provides three constant-current sinks, capable of sinking
16 up to 2 x 400mA (LED1 and LED3) and 800mA (LED2) in flash mode.
17 In torch mode, each sink (LED1, LED2, LED3) supports currents up to 175mA.
19 flash timer, control logic, safety timer and the operating mode, they cannot
[all …]
H A Dmaxim,max77693.yaml1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Krzysztof Kozlowski <krzk@kernel.org>
16 There are two LED outputs available - FLED1 and FLED2. Each of them can
17 control a separate LED or they can be connected together to double the
18 maximum current for a single connected LED. One LED is represented by one
26 const: maxim,max77693-led
28 maxim,boost-mode:
30 In boost mode the device can produce up to 1.2A of total current on both
[all …]
H A Dleds-sc27xx-bltc.txt4 red LED, green LED and blue LED. Each LED can work at normal
5 PWM mode or breath light mode.
8 - compatible: Should be "sprd,sc2731-bltc".
9 - #address-cells: Must be 1.
10 - #size-cells: Must be 0.
11 - reg: Specify the controller address.
14 - reg: Port this LED is connected to.
17 - function: See Documentation/devicetree/bindings/leds/common.txt.
18 - color: See Documentation/devicetree/bindings/leds/common.txt.
19 - label: See Documentation/devicetree/bindings/leds/common.txt (deprecated).
[all …]
H A Dleds-mt6360.yaml1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/leds-mt6360.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: LED driver for MT6360 PMIC from MediaTek Integrated.
10 - Gene Chen <gene_chen@richtek.com>
15 Add MT6360 LED driver include 2-channel Flash LED with torch/strobe mode,
16 and 4-channel RGB LED support Register/Flash/Breath Mode
20 const: mediatek,mt6360-led
22 "#address-cells":
[all …]
H A Dleds-ktd2692.txt1 * Kinetic Technologies - KTD2692 Flash LED Driver
3 KTD2692 is the ideal power solution for high-power flash LEDs.
4 It uses ExpressWire single-wire programming for maximum flexibility.
6 The ExpressWire interface through CTRL pin can control LED on/off and
7 enable/disable the IC, Movie(max 1/3 of Flash current) / Flash mode current,
11 LED current will be ramped up to the flash-mode current level.
14 - compatible : Should be "kinetic,ktd2692".
15 - ctrl-gpios : Specifier of the GPIO connected to CTRL pin.
16 - aux-gpios : Specifier of the GPIO connected to AUX pin.
19 - vin-supply : "vin" LED supply (2.7V to 5.5V).
[all …]
H A Dleds-lm3601x.txt1 * Texas Instruments - lm3601x Single-LED Flash Driver
3 The LM3601X are ultra-small LED flash drivers that
7 - compatible : Can be one of the following
10 - reg : I2C slave address
11 - #address-cells : 1
12 - #size-cells : 0
15 - reg : 0 - Indicates a IR mode
16 1 - Indicates a Torch (white LED) mode
18 Required properties for flash LED child nodes:
20 - flash-max-microamp : Range from 11mA - 1.5A
[all …]
/freebsd/sys/contrib/dev/iwlwifi/mld/
H A Dled.c1 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
8 #include "fw/api/led.h"
10 #include "led.h"
20 if (WARN_ON(!mld->fw_status.running)) in iwl_mld_send_led_fw_cmd()
28 IWL_WARN(mld, "LED command failed: %d\n", err); in iwl_mld_send_led_fw_cmd()
34 struct iwl_mld *mld = container_of(led_cdev, struct iwl_mld, led); in iwl_led_brightness_set()
36 if (!mld->fw_status.running) in iwl_led_brightness_set()
39 iwl_mld_send_led_fw_cmd(mld, brightness > 0); in iwl_led_brightness_set()
44 int mode = iwlwifi_mod_params.led_mode; in iwl_mld_leds_init() local
47 switch (mode) { in iwl_mld_leds_init()
[all …]
/freebsd/sys/contrib/device-tree/Bindings/mfd/
H A Dmax77693.txt1 Maxim MAX77693 multi-function device
4 - PMIC,
5 - CHARGER,
6 - LED,
7 - MUIC,
8 - HAPTIC
14 - compatible : Must be "maxim,max77693".
15 - reg : Specifies the i2c slave address of PMIC block.
16 - interrupts : This i2c device has an IRQ line connected to the main SoC.
19 - regulators : The regulators of max77693 have to be instantiated under subnode
[all …]
H A Dtps6105x.txt3 The TP61050/TPS61052 is a high-power "white LED driver". The
4 device provides LED, GPIO and regulator functionalities.
7 - compatible: "ti,tps61050" or "ti,tps61052"
8 - reg: Specifies the I2C slave address
10 Optional sub-node:
12 This subnode selects the chip's operational mode.
15 - regulator: presence of this sub-node puts the chip in regulator mode.
18 - led: presence of this sub-node puts the chip in led mode.
20 - function : see ../leds/common.txt
21 - color : see ../leds/common.txt
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/microchip/
H A Dsparx5_pcb134_board.dtsi1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
10 gpio-restart {
11 compatible = "gpio-restart";
16 i2c0_imux: i2c-mux-0 {
17 compatible = "i2c-mux-pinctrl";
18 #address-cells = <1>;
19 #size-cells = <0>;
20 i2c-parent = <&i2c0>;
23 i2c0_emux: i2c-mux-1 {
[all …]
/freebsd/sys/contrib/dev/iwlwifi/mvm/
H A Dled.c1 // SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
3 * Copyright (C) 2012-2014, 2018-2019, 2025 Intel Corporation
7 #include "iwl-io.h"
8 #include "iwl-csr.h"
30 IWL_WARN(mvm, "LED command failed: %d\n", err); in iwl_mvm_send_led_fw_cmd()
35 if (fw_has_capa(&mvm->fw->ucode_capa, in iwl_mvm_led_set()
41 iwl_write32(mvm->trans, CSR_LED_REG, in iwl_mvm_led_set()
48 struct iwl_mvm *mvm = container_of(led_cdev, struct iwl_mvm, led); in iwl_led_brightness_set()
50 iwl_mvm_led_set(mvm, brightness > 0); in iwl_led_brightness_set()
55 int mode = iwlwifi_mod_params.led_mode; in iwl_mvm_leds_init() local
[all …]
/freebsd/sys/contrib/device-tree/Bindings/leds/backlight/
H A Dlm3630a-backlight.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/leds/backlight/lm3630a-backlight.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3630A High-Efficiency Dual-String White LED
10 - Lee Jones <lee@kernel.org>
11 - Daniel Thompson <daniel.thompson@linaro.org>
12 - Jingoo Han <jingoohan1@gmail.com>
15 The LM3630A is a current-mode boost converter which supplies the power and
26 '#address-cells':
[all …]
H A Dti,lm3509.yaml1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: TI LM3509 High Efficiency Boost for White LED's and/or OLED Displays
10 - Patrick Gansterer <paroga@paroga.com>
13 The LM3509 current mode boost converter offers two separate outputs.
23 "#address-cells":
26 "#size-cells":
27 const: 0
29 reset-gpios:
[all …]
/freebsd/sys/contrib/device-tree/src/arm/broadcom/
H A Dbcm4709-buffalo-wxr-1900dhp.dts1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WXR-1900DHP
9 /dts-v1/;
12 #include "bcm5301x-nand-cs0-bch8.dtsi"
15 compatible = "buffalo,wxr-1900dhp", "brcm,bcm4709", "brcm,bcm4708";
16 model = "Buffalo WXR-1900DHP";
22 memory@0 {
24 reg = <0x00000000 0x08000000>,
25 <0x88000000 0x18000000>;
29 compatible = "gpio-leds";
[all …]
H A Dbcm4708-buffalo-wzr-1750dhp.dts1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WZR-1750DHP
9 /dts-v1/;
12 #include "bcm5301x-nand-cs0-bch8.dtsi"
15 compatible = "buffalo,wzr-1750dhp", "brcm,bcm4708";
16 model = "Buffalo WZR-1750DHP (BCM4708)";
22 memory@0 {
24 reg = <0x00000000 0x08000000>,
25 <0x88000000 0x18000000>;
29 compatible = "spi-gpio";
[all …]
H A Dbcm4708-buffalo-wzr-1166dhp-common.dtsi1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
4 * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
12 #include "bcm5301x-nand-cs0-bch
[all...]
/freebsd/sys/contrib/device-tree/src/arm64/freescale/
H A Dimx8mm-venice-gw7904.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
6 /dts-v1/;
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/input/linux-event-codes.h>
10 #include <dt-bindings/leds/common.h>
11 #include <dt-bindings/phy/phy-imx8-pcie.h>
17 compatible = "gateworks,imx8mm-gw7904", "fsl,imx8mm";
25 stdout-path = &uart2;
30 reg = <0x0 0x40000000 0 0x80000000>;
33 gpio-keys {
[all …]
/freebsd/sys/contrib/device-tree/src/arm64/marvell/
H A Dcn9132-clearfog.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * Copyright (C) 2024 Josua Mayer <josua@solid-run.com>
9 /dts-v1/;
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/leds/common.h>
15 #include "cn9132-sr-cex7.dtsi"
19 compatible = "solidrun,cn9132-clearfog",
20 "solidrun,cn9132-sr-cex7", "marvell,cn9130";
32 gpio-keys {
33 compatible = "gpio-keys";
[all …]
/freebsd/sys/contrib/device-tree/src/arm/microchip/
H A Dat91-sam9x75_curiosity.dts1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
3 * at91-sam9x75_curiosity.dts - Device Tree file for Microchip SAM9X75 Curiosity board
9 /dts-v1/;
11 #include <dt-bindings/input/input.h>
15 compatible = "microchip,sam9x75-curiosity", "microchip,sam9x7", "atmel,at91sam9";
22 stdout-path = "serial0:115200n8";
25 gpio-keys {
26 compatible = "gpio-keys";
27 pinctrl-names = "default";
28 pinctrl-0 = <&pinctrl_key_gpio_default>;
[all …]
/freebsd/sys/contrib/device-tree/src/arm/marvell/
H A Darmada-385-turris-omnia.dts1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
5 * Copyright (C) 2016 Uwe Kleine-König <uwe@kleine-koenig.org>
8 * Schematic available at https://www.turris.cz/doc/_media/rtrom01-schema.pdf
11 /dts-v1/;
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/input/input.h>
15 #include <dt-bindings/leds/common.h>
16 #include "armada-385.dtsi"
20 compatible = "cznic,turris-omnia", "marvell,armada385", "marvell,armada380";
23 stdout-path = &uart0;
[all …]
/freebsd/sys/contrib/device-tree/src/arm/qcom/
H A Dqcom-ipq8064-rb3011.dts1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-ipq8064.dtsi"
3 #include <dt-bindings/input/input.h>
4 #include <dt-bindings/leds/common.h>
7 model = "MikroTik RB3011UiAS-RM";
14 mdio-gpio0 = &mdio0;
15 mdio-gpio1 = &mdio1;
20 stdout-path = "serial0:115200n8";
23 gpio-keys {
24 compatible = "gpio-keys";
[all …]

12345678910>>...39