| /freebsd/sys/contrib/device-tree/Bindings/media/ |
| H A D | samsung-s5k6a3.txt | 1 Samsung S5K6A3(YX) raw image sensor
2 ---------------------------------
4 S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
9 - compatible : "samsung,s5k6a3";
10 - reg : I2C slave address of the sensor;
11 - svdda-supply : core voltage supply;
12 - svddio-supply : I/O voltage supply;
13 - afvdd-supply : AF (actuator) voltage supply;
14 - gpios : specifier of a GPIO connected to the RESET pin;
15 - clocks : should contain list of phandle and clock specifier pairs
[all …]
|
| H A D | samsung-fimc.txt | 2 ----------------------------------------------
4 The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices
6 the S5P SoCs series known as CAMIF), MIPI CSIS, FIMC-LITE and FIMC-IS (ISP).
8 The sub-subdevices are defined as child nodes of the common 'camera' node which
10 any single sub-device, like common camera port pins or the CAMCLK clock outputs
11 for external image sensors attached to an SoC.
14 --------------------
18 - compatible: must be "samsung,fimc", "simple-bus"
19 - clocks: list of clock specifiers, corresponding to entries in
20 the clock-names property;
[all …]
|
| H A D | video-interface-devices.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
4 $id: http://devicetree.org/schemas/media/video-interface-devices.yaml#
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
10 - Jacopo Mondi <jacopo@jmondi.org>
11 - Sakari Ailus <sakari.ailus@linux.intel.com>
14 flash-leds:
15 $ref: /schemas/types.yaml#/definitions/phandle-array
17 An array of phandles, each referring to a flash LED, a sub-node of the LED
20 lens-focus:
[all …]
|
| H A D | samsung-s5c73m3.txt | 2 ------------------------------
4 The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video
11 ---------------------
15 - compatible : "samsung,s5c73m3";
16 - reg : I2C slave address of the sensor;
17 - vdd-int-supply : digital power supply (1.2V);
18 - vdda-supply : analog power supply (1.2V);
19 - vdd-reg-supply : regulator input power supply (2.8V);
20 - vddio-host-supply : host I/O power supply (1.8V to 2.8V);
21 - vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V);
[all …]
|
| /freebsd/sys/contrib/device-tree/Bindings/media/i2c/ |
| H A D | imx274.txt | 1 * Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor
3 The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with
5 interface. The I2C address is fixed to 0x1a as per sensor data sheet.
6 Image data is sent through MIPI CSI-2, which is configured as 4 lanes
11 - compatible: value should be "sony,imx274" for imx274 sensor
12 - reg: I2C bus address of the device
15 - reset-gpios: Sensor reset GPIO
19 Documentation/devicetree/bindings/media/video-interfaces.txt.
22 sensor@1a {
25 #address-cells = <1>;
[all …]
|
| H A D | sony,imx274.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony 1/2.5-Inch 8.51MP CMOS Digital Image Sensor
10 - Leon Luo <leonl@leopardimaging.com>
13 The Sony IMX274 is a 1/2.5-inch CMOS active pixel digital image sensor with an
15 Image data is sent through MIPI CSI-2, which is configured as 4 lanes at 1440
25 reset-gpios:
31 clock-names:
34 vana-supply:
[all …]
|
| H A D | ov5647.txt | 1 Omnivision OV5647 raw image sensor
2 ---------------------------------
4 OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
9 - compatible : "ovti,ov5647".
10 - reg : I2C slave address of the sensor.
11 - clocks : Reference to the xclk clock.
13 The common video interfaces bindings (see video-interfaces.txt) should be
14 used to specify link to the image data receiver. The OV5647 device
19 - remote-endpoint: A phandle to the bus receiver's endpoint node.
31 remote-endpoint = <&csi1_ep1>;
|
| H A D | mt9v032.txt | 1 * Aptina 1/3-Inch WVGA CMOS Digital Image Sensor
3 The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with
5 two-wire serial interface.
9 - compatible: value should be either one among the following
10 (a) "aptina,mt9v022" for MT9V022 color sensor
11 (b) "aptina,mt9v022m" for MT9V022 monochrome sensor
12 (c) "aptina,mt9v024" for MT9V024 color sensor
13 (d) "aptina,mt9v024m" for MT9V024 monochrome sensor
14 (e) "aptina,mt9v032" for MT9V032 color sensor
15 (f) "aptina,mt9v032m" for MT9V032 monochrome sensor
[all …]
|
| H A D | imi,rdacm2x-gmsl.yaml | 1 # SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
4 ---
5 $id: http://devicetree.org/schemas/media/i2c/imi,rdacm2x-gmsl.yaml#
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
11 - Jacopo Mondi <jacopo+renesas@jmondi.org>
12 - Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
13 - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
14 - Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
16 description: -|
17 The IMI D&D RDACM20 and RDACM21 are GMSL-compatible camera designed for
[all …]
|
| H A D | galaxycore,gc2145.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Galaxy Core 1/5'' UXGA CMOS Image Sensor
10 - Alain Volmat <alain.volmat@foss.st.com>
13 The Galaxy Core GC2145 is a 2 Megapixel CMOS image sensor, for mobile
15 1616V x 1232H active pixel array, on-chip 10-bit ADC, and image signal
16 processor allowing AE/AWB/interpolation/de-noise/color-conversion and
18 sensor. It is programmable through an I2C interface. Image data is sent
19 either through a parallel interface or through MIPI CSI-2.
[all …]
|
| H A D | aptina,mt9v111.txt | 1 * Aptina MT9V111 CMOS sensor
2 ----------------------------
4 The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
5 based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
7 The sensor has an active pixel array of 640x480 pixels and can output a number
8 of image resolution and formats controllable through a simple two-wires
12 --------------------
14 - compatible: shall be "aptina,mt9v111".
15 - clocks: reference to the system clock input provider.
18 --------------------
[all …]
|
| H A D | ov7740.txt | 1 * Omnivision OV7740 CMOS image sensor
3 The Omnivision OV7740 image sensor supports multiple output image
7 The common video interfaces bindings (see video-interfaces.txt) should
8 be used to specify link to the image data receiver. The OV7740 device
12 - compatible: "ovti,ov7740".
13 - reg: I2C slave address of the sensor.
14 - clocks: Reference to the xvclk input clock.
15 - clock-names: "xvclk".
18 - reset-gpios: Rreference to the GPIO connected to the reset_b pin,
19 if any. Active low with pull-ip resistor.
[all …]
|
| H A D | aptina,mt9v111.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Aptina MT9V111 CMOS sensor
10 - Jacopo Mondi <jacopo@jmondi.org>
13 The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
14 based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
16 The sensor has an active pixel array of 640x480 pixels and can output a number
17 of image resolutions and formats controllable through a simple two-wires
30 enable-gpios:
[all …]
|
| H A D | imx219.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
10 - Dave Stevenson <dave.stevenson@raspberrypi.com>
12 description: |-
13 The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor
15 I2C interface. The I2C address is fixed to 0x10 as per sensor data sheet.
16 Image data is sent through MIPI CSI-2, which is configured as either 2 or
30 VDIG-supply:
[all …]
|
| H A D | sony,imx214.txt | 1 * Sony 1/3.06-Inch 13.13Mp CMOS Digital Image Sensor
3 The Sony imx214 is a 1/3.06-inch CMOS active pixel digital image sensor with
6 Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a maximum
11 - compatible: Shall be "sony,imx214".
12 - reg: I2C bus address of the device. Depending on how the sensor is wired,
14 - enable-gpios: GPIO descriptor for the enable pin.
15 - vdddo-supply: Chip digital IO regulator (1.8V).
16 - vdda-supply: Chip analog regulator (2.7V).
17 - vddd-supply: Chip digital core regulator (1.12V).
18 - clocks: Reference to the xclk clock.
[all …]
|
| H A D | imx290.txt | 1 * Sony IMX290 1/2.8-Inch CMOS Image Sensor
3 The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with
4 Square Pixel for Color Cameras. It is programmable through I2C and 4-wire
5 interfaces. The sensor output is available via CMOS logic parallel SDR output,
6 Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the
10 - compatible: Should be "sony,imx290"
11 - reg: I2C bus address of the device
12 - clocks: Reference to the xclk clock.
13 - clock-names: Should be "xclk".
14 - clock-frequency: Frequency of the xclk clock in Hz.
[all …]
|
| H A D | sony,imx258.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor
10 - Krzysztof Kozlowski <krzk@kernel.org>
12 description: |-
13 IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel
14 type stacked image sensor with a square pixel array of size 4208 x 3120. It
15 is programmable through I2C interface. Image data is sent through MIPI
16 CSI-2. The sensor exists in two different models, a standard variant
[all …]
|
| H A D | mt9p031.txt | 1 * Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
3 The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with
5 two-wire serial interface.
8 - compatible: value should be either one among the following
9 (a) "aptina,mt9p031" for mt9p031 sensor
10 (b) "aptina,mt9p031m" for mt9p031m sensor
12 - input-clock-frequency: Input clock frequency.
14 - pixel-clock-frequency: Pixel clock frequency.
17 - reset-gpios: Chip reset GPIO
20 Documentation/devicetree/bindings/media/video-interfaces.txt.
[all …]
|
| H A D | mt9m001.txt | 1 MT9M001: 1/2-Inch Megapixel Digital Image Sensor
3 The MT9M001 is an SXGA-format with a 1/2-inch CMOS active-pixel digital
4 image sensor. It is programmable through I2C interface.
8 - compatible: shall be "onnn,mt9m001".
9 - clocks: reference to the master clock into sensor
13 - reset-gpios: GPIO handle which is connected to the reset pin of the chip.
15 - standby-gpios: GPIO handle which is connected to the standby pin of the chip.
19 sub-node for its digital output video port, in accordance with the video
21 Documentation/devicetree/bindings/media/video-interfaces.txt
26 camera-sensor@5d {
[all …]
|
| H A D | imx258.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor
10 - Krzysztof Kozlowski <krzk@kernel.org>
12 description: |-
13 IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel
14 type stacked image sensor with a square pixel array of size 4208 x 3120. It
15 is programmable through I2C interface. Image data is sent through MIPI
16 CSI-2.
[all …]
|
| H A D | sony,imx296.yaml | 1 # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony IMX296 1/2.8-Inch CMOS Image Sensor
10 - Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
11 - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
13 description: |-
14 The Sony IMX296 is a 1/2.9-Inch active pixel type CMOS Solid-state image
15 sensor with square pixel array and 1.58 M effective pixels. This chip
16 features a global shutter with variable charge-integration time. It is
[all …]
|
| H A D | samsung,s5k6a3.yaml | 1 # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Samsung S5K6A3(YX) raw image sensor
10 - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
13 S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data
26 clock-names:
28 - const: extclk
30 clock-frequency:
38 afvdd-supply:
[all …]
|
| H A D | ovti,og01a1b.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 # Copyright (c) 2023-2024 Linaro Ltd.
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: OmniVision OG01A1B Image Sensor
11 - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
15 image sensor controlled over an I2C-compatible SCCB bus.
16 The sensor transmits images on a MIPI CSI-2 output interface with one or
20 - $ref: /schemas/media/video-interface-devices.yaml#
32 reset-gpios:
[all …]
|
| H A D | sony,imx283.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
4 ---
6 $schema: http://devicetree.org/meta-schemas/core.yaml#
8 title: Sony IMX283 Sensor
11 - Kieran Bingham <kieran.bingham@ideasonboard.com>
12 - Umang Jain <umang.jain@ideasonboard.com>
15 IMX283 sensor is a Sony CMOS active pixel digital image sensor with an active
17 I2C client address is fixed to 0x1a as per sensor data sheet. Image data is
18 sent through MIPI CSI-2.
31 vadd-supply:
[all …]
|
| H A D | sony,imx214.yaml | 1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
3 ---
5 $schema: http://devicetree.org/meta-schemas/core.yaml#
7 title: Sony 1/3.06-Inch 13.13MP CMOS Digital Image Sensor
10 - Ricardo Ribalda <ribalda@kernel.org>
13 The Sony IMX214 is a 1/3.06-inch CMOS active pixel digital image sensor with
15 interface. Image data is sent through MIPI CSI-2, through 2 or 4 lanes at a
19 - $ref: /schemas/media/video-interface-devices.yaml#
27 - 0x10
28 - 0x1a
[all …]
|