| /linux/drivers/pwm/ |
| H A D | pwm-sl28cpld.c | 27 * which might lead to glitches and inconsistent states if a write fails.
29 * to glitches, too.
170 * To avoid glitches when we switch the prescaler, we have to make sure in sl28cpld_pwm_apply()
|
| H A D | pwm-mxs.c | 94 * glitches. in mxs_pwm_apply()
|
| H A D | pwm-microchip-core.c | 12 * writes will take effect immediately, causing glitches on the output.
27 * some output glitches) rather than 50%.
|
| H A D | pwm-renesas-tpu.c | 164 * glitches. in tpu_pwm_timer_start()
|
| /linux/Documentation/userspace-api/gpio/ |
| H A D | gpio-v2-line-set-config-ioctl.rst | 36 line or introducing potential glitches.
|
| H A D | gpio-handle-set-config-ioctl.rst | 40 line or introducing potential glitches.
|
| /linux/drivers/pinctrl/meson/ |
| H A D | pinctrl-meson8-pmx.c | 71 * The selected group is not disabled to avoid glitches. in meson8_pmx_set_mux()
|
| /linux/drivers/reset/hisilicon/ |
| H A D | hi6220_reset.c | 133 * the clocks and deasserting reset, to avoid glitches. in hi6220_ao_deassert()
|
| /linux/Documentation/devicetree/bindings/clock/ |
| H A D | silabs,si5351.yaml | 83 to be adjusted without glitches.
|
| /linux/Documentation/core-api/ |
| H A D | errseq.rst | 100 glitches and he makes a mistake. He sighs a heavy sigh, and marks it
|
| /linux/Documentation/driver-api/ |
| H A D | pwm.rst | 167 about the current PWM state would allow him to avoid glitches.
|
| /linux/drivers/watchdog/ |
| H A D | rti_wdt.c | 136 * To avoid any glitches, we accommodate 2% + max hardware error in rti_wdt_setup_hw_hb()
|
| /linux/drivers/regulator/ |
| H A D | ti-abb-regulator.c | 266 * be performed *before* switch to bias mode else VBB glitches. in ti_abb_set_opp()
286 * be performed *after* switch to bypass else VBB glitches. in ti_abb_set_opp()
|
| H A D | max8660.c | 420 * First, set up shadow registers to prevent glitches. As some in max8660_probe()
|
| /linux/Documentation/admin-guide/laptops/ |
| H A D | asus-laptop.rst | 108 - W1000N (albeit with some glitches)
|
| /linux/arch/arm/mach-s3c/ |
| H A D | pm-gpio.c | 98 * not as simple as once thought, due to the possibility of glitches
|
| /linux/sound/soc/meson/ |
| H A D | axg-spdifin.c | 67 * 2. Mode detection very often has glitches, and may detects the
|
| /linux/drivers/phy/lantiq/ |
| H A D | phy-lantiq-vrx200-pcie.c | 137 /* Reduced CDR BW to avoid glitches */ in ltq_vrx200_pcie_phy_common_setup()
|
| /linux/Documentation/sound/cards/ |
| H A D | emu-mixer.rst | 22 In particular, I got recording glitches during simultaneous playback on an
|
| /linux/drivers/gpio/ |
| H A D | gpio-tangier.c | 280 * To prevent glitches from triggering an unintended level interrupt, in tng_irq_set_type()
|
| /linux/drivers/i2c/busses/ |
| H A D | i2c-img-scb.c | 1203 * The clock generation logic allows to filter glitches on the bus. in img_i2c_init()
1204 * This filter is able to remove bus glitches shorter than 50ns. in img_i2c_init()
|
| /linux/drivers/net/ethernet/sfc/falcon/ |
| H A D | txc43128_phy.c | 464 * it glitches the link, and reconfigure gets called on link change, in txc43128_phy_reconfigure()
|
| /linux/drivers/gpu/drm/radeon/ |
| H A D | rs400.c | 266 * Problems shown up as HyperZ glitches, see: in rs400_gpu_init()
|
| /linux/Documentation/fb/ |
| H A D | matroxfb.rst | 91 architectures there are some glitches for 24bpp videomodes. 8, 16 and 32bpp
|
| /linux/drivers/thermal/ |
| H A D | armada_thermal.c | 791 * possible glitches by always selecting back only one channel (arbitrarily: the
|