Home
last modified time | relevance | path

Searched full:flagged (Results 1 – 25 of 175) sorted by relevance

1234567

/linux/Documentation/devicetree/bindings/serio/
H A Dps2-gpio.yaml18 the gpio used for the data signal - this should be flagged as
26 the gpio used for the clock signal - this should be flagged as
/linux/include/uapi/linux/
H A Dneighbour.h80 * flagged entries explicitly are (which is also consistent with the routing
87 * NTF_EXT_MANAGED flagged neigbor entries are managed by the kernel on behalf
91 * NTF_EXT_LOCKED flagged bridge FDB entries are entries generated by the
H A Dbsg.h30 __u64 request_tag; /* [i] {SCSI: task tag (only if flagged)} */
H A Ddlm.h51 * -EAGAIN if request would block and is flagged DLM_LKF_NOQUEUE
/linux/Documentation/devicetree/bindings/i2c/
H A Di2c-gpio.yaml22 gpio used for the sda signal, this should be flagged as
30 gpio used for the scl signal, this should be flagged as
/linux/Documentation/devicetree/bindings/input/
H A Datmel,maxtouch.yaml42 (active low). The line must be flagged with
49 (active low). The line must be flagged with
/linux/drivers/power/supply/
H A Dmax8903_charger.c91 * library as the line should be flagged GPIO_ACTIVE_LOW in the device in max8903_dcin()
150 * library as the line should be flagged GPIO_ACTIVE_LOW in the device in max8903_usbin()
206 * library as the line should be flagged GPIO_ACTIVE_LOW in the device in max8903_fault()
/linux/Documentation/devicetree/bindings/gnss/
H A Dmediatek.yaml31 If the line is active low it should be flagged with GPIO_ACTIVE_LOW.
H A Dbrcm,bcm4751.yaml45 description: An optional active low reset line, should be flagged with
H A Dsirfstar.yaml47 description: An optional active low reset line, should be flagged with
/linux/arch/powerpc/include/asm/nohash/32/
H A Dpte-8xx.h162 * 4k pages, but they are flagged as 512k pages for the hardware.
164 * but they are flagged as 8M pages for the hardware.
/linux/drivers/net/ethernet/toshiba/
H A Dspider_net.h151 /* we rely on flagged descriptor interrupts */
323 /* We rely on flagged descriptor interrupts */
/linux/Documentation/networking/
H A Drxrpc.rst244 (#) When receiving data or messages for a call, MSG_EOR is flagged by recvmsg
315 for the next taker. MSG_TRUNC will never be flagged.
319 flagged.
616 pick up. MSG_MORE will be flagged by recvmsg() if there's more reply data
625 buffer instead, and MSG_EOR will be flagged to indicate the end of that
724 be delivered with MSG_MORE flagged.
752 MSG_EOR will be flagged to indicate that this is the final message for
/linux/Documentation/devicetree/bindings/iio/light/
H A Dcapella,cm3605.yaml29 ASET line (drive low to activate the ALS, should be flagged
/linux/drivers/clk/davinci/
H A Dpll-da830.c27 * NB: Technically, the clocks flagged as SYSCLK_FIXED_DIV are "fixed ratio",
/linux/Documentation/devicetree/bindings/nvmem/layouts/
H A Du-boot,env.yaml34 - description: Two redundant blocks with active one flagged
/linux/drivers/gpu/drm/nouveau/nvkm/engine/fifo/
H A Drunl.c74 /* Look for channel groups flagged for RC. */ in nvkm_runl_rc()
100 /* Look for engines that are still on flagged channel groups - reset them. */ in nvkm_runl_rc()
/linux/drivers/clk/qcom/
H A Dkrait-cc.c128 /* clk-krait ignore any rate change if mux is not flagged as enabled */ in krait_add_div()
212 /* clk-krait ignore any rate change if mux is not flagged as enabled */ in krait_add_sec_mux()
/linux/drivers/regulator/
H A Dirq_helpers.c218 * If any of the flagged regulators is enabled we do in regulator_notifier_isr()
321 * @common_errs: Errors which can be flagged by this IRQ for all rdevs.
/linux/Documentation/userspace-api/media/v4l/
H A Dpixfmt-v4l2-mplane.rst35 compressed data flagged with ``V4L2_FMT_FLAG_COMPRESSED`` at
/linux/Documentation/filesystems/
H A Dautomount-support.rst59 If a vfsmount was already flagged for expiry, and if its usage count is 1
/linux/Documentation/devicetree/bindings/soc/qcom/
H A Dqcom,smsm.yaml64 node. Nodes can either be flagged as an interrupt-controller to denote a
/linux/Documentation/dev-tools/
H A Dcheckuapi.rst368 types of changes may be flagged even though they intentionally break UAPI.
450 This change would be flagged by the script::
469 break userspace would not be flagged by this script. While the script
/linux/arch/arm/boot/dts/intel/ixp/
H A Dintel-ixp42x-dlink-dsm-g600.dts47 /* CHECKME: flagged as active low in the old board file */
/linux/Documentation/block/
H A Dwriteback_cache_control.rst27 storage before the flagged bio starts. In addition the REQ_PREFLUSH flag can be

1234567