| /linux/Documentation/trace/ |
| H A D | ftrace-uses.rst | 34 RCU is watching. These are explained below.
142 (as explained below), then a helper trampoline will be used to test
158 (as explained below), then a helper trampoline will be used to test
|
| /linux/arch/arm64/boot/dts/marvell/ |
| H A D | ac5x-rd-carrier.dtsi | 16 * So in this case, once the switch is set to external mode as explained above,
|
| H A D | ac5x-rd-carrier-cn9131.dts | 16 * So in this case, once the switch is set to external mode as explained above,
|
| /linux/Documentation/watchdog/ |
| H A D | convert_drivers_to_kernel_api.rst | 117 explained in 'watchdog-kernel-api.txt' in this directory. start() and
155 necessary information for the framework. The struct is also explained in detail
|
| /linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | lltc,ltc294x.yaml | 42 The prescaler exponent as explained in the datasheet.
|
| /linux/Documentation/devicetree/bindings/cache/ |
| H A D | freescale-l2cache.txt | 4 The cache bindings explained below are Devicetree Specification compliant
|
| /linux/Documentation/virt/ |
| H A D | guest-halt-polling.rst | 26 in response to events (explained below).
|
| /linux/drivers/media/rc/img-ir/ |
| H A D | img-ir-rc6.c | 43 * Due to the above explained irregularity the trailer bits cannot in img_ir_rc6_scancode()
|
| /linux/Documentation/scheduler/ |
| H A D | sched-arch.rst | 60 interrupts disabled, as explained in 3).
|
| /linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | abilis,tb10x-iomux.txt | 46 explained in Documentation/devicetree/bindings/gpio/gpio.txt.
|
| H A D | pinctrl-st.txt | 115 Each parameter is explained as below.
|
| /linux/fs/udf/ |
| H A D | unicode.c | 10 * OSTA Compressed Unicode is explained in the OSTA UDF specification.
12 * UTF-8 is explained in the IETF RFC XXXX.
|
| /linux/Documentation/fb/ |
| H A D | deferred_io.rst | 60 explained below.
|
| /linux/Documentation/driver-api/driver-model/ |
| H A D | device.rst | 56 As explained in Documentation/core-api/kobject.rst, device attributes must be
|
| /linux/Documentation/hwmon/ |
| H A D | lm83.rst | 63 The fact that the LM83 is only scarcely used can be easily explained.
|
| /linux/Documentation/admin-guide/ |
| H A D | quickly-build-trimmed-linux.rst | 242 additional adjustments explained in the reference section.
308 tag, as explained earlier. Afterwards adjust the build configuration to the
731 As explained briefly in the step-by-step guide already: with localmodconfig it
813 chance that you need to decode a stack trace later (as explained by 'Decode
847 -- or generate your own, as explained in
1004 explained the setup described in more detail <sources>`: you need to use a
|
| H A D | lockup-watchdogs.rst | 62 As explained above, a kernel knob is provided that allows
|
| H A D | reporting-regressions.rst | 61 using ``make olddefconfig``, as explained in more detail below.
89 regression using a bisection, as explained below in more detail.
276 development cycle a test run. This is best explained by imagining a change
|
| /linux/arch/powerpc/kernel/ |
| H A D | idle_6xx.S | 89 * L2 prefetch engines are idle. As explained by errata
|
| /linux/Documentation/cpu-freq/ |
| H A D | cpufreq-stats.rst | 35 cpufreq stats provides following statistics (explained in detail below).
|
| /linux/Documentation/driver-api/ |
| H A D | rfkill.rst | 130 "type" sysfs files explained above.
|
| /linux/Documentation/security/ |
| H A D | SCTP.rst | 92 SCTP_PARAM_SET_PRIMARY - Reconfiguration is enabled as explained below.
293 to a specific port type and the ``association`` permission that is explained
|
| /linux/Documentation/networking/ |
| H A D | fib_trie.rst | 18 A few concepts explained
|
| /linux/drivers/media/platform/renesas/vsp1/ |
| H A D | vsp1_lif.c | 137 * manual is not explained but is likely a buffer size or threshold. in lif_configure_stream()
|
| /linux/Documentation/virt/kvm/x86/ |
| H A D | nested-vmx.rst | 75 which L0 builds to actually run L2 - how this is done is explained in the
|